RGP10A THRU RGP10M GLASS PASSIVATED JUNCTION FAST SWITCHING RECTIFIER * Reverse Voltage - 50 to 1000 Volts FEATURES ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ High temperature metallurgically bonded construction ♦ Glass passivated cavity-free junction ♦ Capable of meeting environmental standards of MIL-S-19500 ♦ For use in high frequency rectifier circuits ♦ Fast switching for high efficiency ♦ 1.0 Ampere operation at TA=55°C with no thermal runaway ♦ Typical IR less than 0.1µA ♦ High temperature soldering guaranteed: 350°C/10 seconds 0.375" (9.5mm) lead length, 5 lbs. (2.3kg) tension N T E D DO-204AL E P A T Forward Current - 1.0 Ampere 1.0 (25.4) MIN. 0.107 (2.7) 0.080 (2.0) DIA. 0.205 (5.2) 0.160 (4.1) 1.0 (25.4) MIN. 0.034 (0.86) 0.028 (0.71) DIA. NOTE: Lead diameter is 0.026 (0.66) 0.023 (0.58) for suffix "E" part numbers MECHANICAL DATA Dimensions in inches and (millimeters) *Glass-plastic encapsulation technique is covered by Case: JEDEC DO-204AL molded plastic over glass body Terminals: Plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight: 0.012 ounce, 0.3 gram Patent No. 3,996,602 and brazed-lead assembly by Patent No. 3,930,306 ® MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS RGP 10A RGP 10B RGP 10D RGP 10G RGP 10J RGP 10K RGP 10M UNITS Maximum recurrent peak reverse voltage VRRM 50 100 200 400 600 800 1000 Volts Maximum RMS voltage VRMS 35 70 140 280 420 560 700 Volts Maximum DC blocking voltage VDC 50 100 200 400 600 800 1000 Volts Maximum average forward rectified current 0.375" (9.5mm) lead length at TA=55°C I(AV) 1.0 Amp Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) IFSM 30.0 Amps Maximum instantaneous forward voltage at 1.0A VF 1.3 Volts Maximum full load reverse current, full cycle average 0.375" (9.5mm) lead length TA=55°C IR 100.0 µA Maximum DC reverse current at rated DC blocking voltage IR 5.0 200.0 µA TA=25°C TA=150°C Maximum reverse recovery time (NOTE 1) Typical junction capacitance (NOTE 2) Typical thermal resistance (NOTE 3) Operating junction and storage temperature range trr 250 500 ns CJ 15.0 pF RΘJA 55.0 °C/W TJ, TSTG -65 to +175 °C NOTES: (1) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25A (2) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts (3) Thermal resistance from junction to ambient at 0.375" (9.5mm) lead length, P.C.B. mounted 4/98 150 RATINGS AND CHARACTERISTIC CURVES RGP10A THRU RGP10M FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 1.0 30 RESISTIVE OR INDUCTIVE LOAD FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD RECTIFIED CURRENT, AMPERES FIG. 1 - FORWARD CURRENT DERATING CURVE 0.75 0.5 0.25 20 10 0 0.375" (9.5mm) LEAD LENGTH 0 25 50 75 100 125 150 TJ=TJ max. 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 1 10 100 NUMBER OF CYCLES AT 60 HZ 175 AMBIENT TEMPERATURE, °C FIG. 4 - TYPICAL REVERSE CHARACTERISTICS FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 20 10 10 INSTANTANEOUS REVERSE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT, AMPERES TJ=125°C TJ=25°C 1 PULSE WIDTH=300µs 1% DUTY CYCLE 0.1 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1 TJ=75°C 0.1 TJ=25°C 1.6 INSTANTANEOUS FORWARD VOLTAGE, VOLTS 0.01 0 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE, % FIG. 5 - TYPICAL JUNCTION CAPACITANCE 100 10 1 1 10 REVERSE VOLTAGE, VOLTS 100 FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE TRANSIENT THERMAL IMPEDANCE (°C/W) JUNCTION CAPACITANCE pF TJ=25°C f=1.0 MHZ Vsig=50mVp-p 100 10 1 0.1 0.01 0.1 1 t, PULSE DURATION, sec 10 100