SINAMICS V20 The cost-effective, reliable and easy-to-use AC drive for basic applications usa.siemens.com/sinamics-v20 Answers for industry. SINAMICS V20 The perfect drive solution for basic applications Power range 0.12–30kW (1/6–40 hp) Voltage range 1AC 200V ... 240V (+ / –10%) 3AC 380V ... 480V (+10 % / –15%) Control modes V/f V2/f FCC V/f multi-point SINAMICS V20, the simple and versatile drive system for basic demands Today, in an increasing number of applications, automation and drive solutions are required to automate motion sequences. The SINAMICS V20 from Siemens offers a simple drive solution for these types of applications. It sets itself apart with its quick commissioning times, robustness, ease-of-operation and cost-efficiency. With five frame sizes, it covers a power range extending from 0.12 kW up to 30 kW (1/6 hp up to 40 hp). Minimize your costs In today’s competitive environment, engineering, commissioning and operating costs must be kept to a minimum. With SINAMICS V20, you have the precise answer. To increase energy efficiency, the drive uses a control technique, which automatically reduces motor flux when the motor is not operating at optimal loading (ECO mode). The V20 displays actual energy consumption and has a “hibernate” mode for periods when the drive is not being used — allowing energy consumption to be drastically reduced. Easy-to-install n Push-through and wall mounting — side-by-side possible for both n USS and Modbus RTU at terminals n Integrated braking chopper for 7.5–30 kW (10–40 hp) Easy-to-use n Parameter loading without power supply n Integrated application and connection macros n Keep Running Mode for uninterrupted operation n Advanced cooling design and coated PCBs increase robustness Easy to save money 2 n ECO mode for V/f, V2/f n Hibernation mode n DC coupling n High overload and low overload mode for FSE Typical applications and SINAMICS V20 benefits Pumping, ventilating and compressing n High availability through automatic restart and flying restart after power failures n Broken belt detection by monitoring the load torque n Pump protection against cavitation n Hammer start and blockage clearing modes for clogged pumps n PID controller for process values (e.g. temperature, pressure, level, flow) n PID auto tuning to optimize controller parameters n Hibernation mode stops the motor when demand is low n n Centrifugal pumps n Radial / axial fans n Compressors n Motor staging extends the flow range by adding two more fixed-speed drives (cascade) Frost and condensation protection preventsmoisture in motors under extreme environmental conditions Moving n n Super torque start for conveyor belts with high breakaway torque n Dynamic behavior by using braking resistor or DC braking n Direct control of mechanical holding brake n Broken belt detection by monitoring the load torque n n Belt conveyors n Roller conveyors n Chain conveyors Soft, jerk-free acceleration reduces the stress on the gear units, bearings, drums and rollers Precise stopping with Quick Stop (switch-off positioning) independently from the control cycle Processing n n n Single drives in the process industry such as mills, mixers, kneaders, crushers, agitators, centrifuges Main drives in machines with mechanically coupled axes such as ring spinning machines, braiding machines for textile, ropes and wire Frost and condensation protection prevents moisture in motors under extreme environmental conditions n Higher productivity with uninterrupted production due to Keep Running Mode n Exchange of regenerative energy via the DC link n Super torque start for machines with a high breakaway torque 3 SINAMICS V20 — Easy-to-install Installation SINAMICS V20 feature Wall mounting Side-by-side mounting Push-through mounting V20 No space required Cooling Cooling Compact design, side-by-side mounting and flexible device installation for both wall mounting and push-through mounting. Operation without additional option modules possible. Your benefits n n n n Compact installation allows smaller cabinets to be used Push-through mounting allows the cabinet to be cooled more easily Can be run “out-of-the-box” without other options Basic operator actions at a built-in BOP (Basic Operator Panel) Communication SINAMICS V20 feature Siemens products Other products Standard library USS The communication port is available at the terminals. The preset parameters of the USS and Modbus RTU are defined in the connection macro. Your benefits n n n Modbus Easy integration into existing systems Easy integration into micro automation systems Easier commissioning through standard libraries and connection macros SINAMICS V20 Braking module SINAMICS V20 feature Your benefits SINAMICS V20 The dynamic energy is dissipated as heat in a braking resistor with an adjustable duty cycle of between 5–100%. Braking module Motor f t 4 Resistor n n Possible to use dynamic braking to increase braking performance Drives ≥ 7.5 kW have an integrated braking module. In this case, the braking resistor can be directly connected. SINAMICS V20 — Easy-to-use Parameter cloning SINAMICS V20 feature Parameter loading Commissioning Parameter settings can be easily transferred from one unit to another using the parameter loader — even without a power supply. Your benefits n Less technical support required n Short commissioning time n The product is delivered to the customer already preset Copy configuration Macro approach SINAMICS V20 feature Connection and application macros to simplify I/O configuration and make the appropriate settings. Your benefits n n n Fan Macro SINAMICS V20 n Shorter training and commissioning time Integrated and optimized application setting Simple connection and application macros can be selected instead of configuring long complicated parameter lists Errors caused by wrong parameter settings can be avoided Keep Running Mode SINAMICS V20 feature The function provides higher productivity in production by automatic adaptation in the case of unstable line supplies. SINAMICS V20 Your benefits n n Motor n Stable operation under difficult line supply conditions Higher productivity through prevention of interruptions of the production line Adaptation to application-relevant reactions through flexible definition in case of fault / alarm Robustness SINAMICS V20 feature Better cooling design and coated PCB increase robustness of the drive in difficult application environments. Your benefits n n SINAMICS V20 n Motor Operation possible when the line supply voltage fluctuates Reliable operation for line voltages: 1AC 200V … 240V (–10% / +10%) 3AC 380V … 480V (–15% / +10%) Operation up to an ambient temperature of 60° C 5 SINAMICS V20 — Easy to save money Energy reduction during operation ¹⁾ SINAMICS V20 feature Integrated ECO mode for V/f and V2/f automatically adapts the flux to save energy. The energy consumption can be shown in kWh, CO2 or even in the local currency. 60% UP TO ENERGY-SAVINGS POTENTIAL Your benefits n n n Energy saving during low dynamic load cycles If the setpoint changes, the ECO mode is automatically deactivated Tells end-users the actual energy that has been saved Energy reduction during operation — DC coupling Energy consumption Energy generation SINAMICS V20 feature Applications that use SINAMICS V20 drives with the same power rating can share a common DC bus to reuse the regenerative energy. Your benefits n n Energy n SINAMICS V20 SINAMICS V20 Generate and save energy in applications that use coupled motors Pairs of identical drives can optimally share resources Reduce the need for dynamic braking and external components Energy reduction during standby — hibernation mode SINAMICS V20 feature f Save energy threshold t Inverter and motor only operate when the plant or machine re-quires them to. Hibernation mode will be automatically activated when the frequency demand or the feedback from a sensor drops below a specific threshold. Your benefits n Smart hibernation saves energy n Extended lifetime of motor n Reduced pump wear at low speed n Less time to program PLC code for pump / fan applications (PLC) Cost-savings at low overload application High Overload Low Overload SINAMICS V20 feature SINAMICS V20 FSE (22 kW and 30 kW) integrated two different load cycles. n n Low Overload (LO): 110% IL ²) for 60 s (cycle time: 300 s) High Overload (HO): 150% IH ³) for 60 s (cycle time: 300 s) ¹⁾ Application and machine-type dependent ²⁾ The output current IL is based upon the duty cycle for low overload (LO). ³⁾ The output current IH is based upon the duty cycle for high overload (HO). 6 Your benefits n n With low overload cycle, the drive can reach a higher output current and power. A smaller drive can be used. Optimally designed for a variety of applications: Low Overload for applications with a low dynamic response (continuous duty) High Overload for applications with a high dynamic response (cyclic duty) n n Combining SINAMICS V20 drives with SIMATIC PLC Easy automation system SIMATIC Panel SIMATIC PLC Ethernet / PROFINET SINAMICS V20 USS MODBUS RTU Saving time and minimizing errors n Easy system configuration with pre-defined macros in the drive and pre-built Totally Integrated Automation Portal function blocks for quick connection to SIMATIC S7-1200** n One cable to connect SINAMICS V20 with USS or MODBUS RTU n Integrated communication interface ** A pplication example with function blocks can be downloaded from Siemens Industry Online Support: http://support.automation.siemens.com/WW/view/en/63696870 7 SINAMICS V20 — Overload capability characteristics M= n² P ~ n³ M= torque n = speed P = power Low Overload (LO) is generally used for applications demanding a low level of dynamic performance (continuous duty), square-law torque characteristic with low breakaway torque and low speed precision. For example: centrifugal pumps, radial / axial fans, reciprocating blowers, radial compressors, vacuum pumps, agitators, etc. Low overload (LO) capability 110% IL ¹) for 60 s within a cycle time of 300 s ¹) The output current IL is based on the duty cycle for low overload (LO). M= constant P ~ n M= torque n = speed P = power High Overload (HO) is generally used for applications demanding a higher dynamic performance (cyclic duty), as well as constant torque characteristics with a high breakaway torque. For example: conveyor belts, geared pumps, eccentric worm pumps, mills, mixers, crushers, vertical conveying equipment, centrifuges, etc. High overload (HO) capability 150% IH ²) for 60 s within a cycle time of 300 s 2) The output current IH is based on the duty cycle for high overload (HO). SINAMICS V20 — best-in-class service and support At home or across the globe n n n 8 Global hotline support Comprehensive service network of factory-trained repair specialists Online Support The comprehensive online information platform supports you in all aspects of our service and support at any time and from any location in the world. Multiple language web-based support and FAQs siemens.com/automation/service&support Country Hotline Technical support USA +1 423 262 5710 / +1 800 333 7421 Germany +49 911 895 7222 India +91 22 2760 0150 China +86 400 810 4288 Expert advice on technical questions with a wide range of demand-optimized services for all our products and systems. Additional service contact information: siemens.com/automation/support-request SINAMICS V20 — Full range of options, everything you need… Fuse Circuit breaker V20 BOP (Basic Operator Panel) Line reactor Braking resistor, small (FSA, FSB, FSC) Braking resistor, large (FSD and FSE) Line filter BOP Cable BOP Interface (Basic Operator Panel) Braking module (FSA, FSB, FSC) SINAMICS Memory Card (SD) Shield connection kit Output reactor Parameter loader SINAMICS V20 — Options V20 BOP Same functionality as the integrated Basic Operator Panel (BOP), but can be used for remote mounting. The value and setpoint are changed by rotating the wheel. BOP interface n Connection between inverter and BOP BOP cable 3 m cable with connectors Parameter loader Up to 100 parameter sets with parameter settings can be written from the memory card to the inverter or saved from the inverter to the memory card without connecting the inverter to the line supply. SINAMICS Memory Card (SD) n 512 MB Line filter n Improved EMC performance n Longer motor cable for FSA Line reactor n Reduces the harmonic current n Improves the power factor n Recommended if input current (RMS value) is higher than the rated current of the drive. Braking module n Shortens the deceleration ramp time n Suitable for 1AC 230V and 3AC 400V n Adjustable duty cycle from 5–100% n FSD and FSE already have an integrated braking unit Braking resistor n Dissipates regenerative energy as heat n 5% duty cycle as default setting Output reactor Longer motor cable: n 3AC 400V shielded and unshielded cable: 150 m n 1AC 230V shielded and unshielded cable: 200 m Shield connection kit n Shield connection n Strain relief Fuse Recommended fuse corresponding to the EC/UL standard Circuit breaker Recommended circuit breaker corresponding to the EC/UL standard 9 Technical information Power and control Voltage 1AC 230V: 1AC 200V ... 240V (–10% ... +10%) 3AC 400V: 3AC 380V ... 480V (–15% ... +10%) Maximum output voltage 100% of input voltage Supply frequency 50 / 60 Hz Line supply type TN, TT, TT earthed line, IT ¹) Power range 1AC 230V 0.12 … 3.0 kW (1/6 … 4 hp) 3AC 400V 0.37 … 30 kW (1/2 … 40 hp) cos φ / Power factor ≥ 0.95 / 0.72 Overload capability up to 15 kW: High Overload (HO): 150% IH for 60 s within a cycle time of 300 s from 18.5 kW: Low Overload (LO): 110% IL for 60 s within a cycle time of 300 s High Overload (HO): 150% IH for 60 s within a cycle time of 300 s Output frequency 0 ... 550 Hz resolution: 0.01 Hz Efficiency factor 98% Control modes Voltage / frequency control mode: linear V/f, square law V/f, multi-point V/f Flux current control mode: FCC Standards Standards CE, cULus, C-tick, KC EMC standards, radiated emissions and disturbance voltage (conducted emissions) EN61800-3 category C2, 1st environment (domestic premises): n n 1AC 230V with integrated line filter, shielded cables ≤ 25 m (FSA ≤ 10 m ²)) 3AC 400V without integrated line filter with external line filter, shielded cables FSA up to FSD ≤ 25 m, FSE ≤ 50 m EN61800-3 category C3, 2nd environment (industrial premises): n 3AC 400V with integrated line filter, shielded cables FSA ≤ 10 m, FSB up to FSD ≤ 25 m, FSE ≤ 50 m Features Energy savings Ease-of-use Application Protection n ECO mode n Hibernation mode n Energy consumption monitoring n n Connection and application macro n Drive status at fault Parameter cloning n Automatic restart n Keep Running Mode n Flying start n USS / Modbus RTU communication n DC-link voltage control n Customized default value n Imax control n List of modified parameters n PID controller n Flexible boost control n BICO function n Wobble function n Hammer start n Slip compensation n Super torque mode n Dual ramp n Blockage clearing mode n Adjustable PWM modulation n Motor staging n Frost protection n Kinetic buffering n Condensation protection n Load failure detection n Cavitation protection ¹) Only 3AC 400V unfiltered devices can be operated at IT network. ²) To achieve 25 m shielded motor cable length also with FSA, unfiltered devices with external filter have to be used. 10 Signal inputs and outputs Analog inputs AI1: bipolar current / voltage mode AI2: unipolar current / voltage mode Can be used as digital inputs Analog outputs A01: 0 … 20 mA Digital inputs DI1–DI4, optically isolated PNP/NPN selectable by terminal Digital outputs DO1: transistor output DO2: relay output n n 250V AC 0.5 A with resistive load 30V DC 0.5 A with resistive load Connection diagram FSA up to FSC FSD, FSE 400 V Main circuit M 230 V Control circuit External 24V supply Digital inputs Digital outputs Internal 24V supply Transistor output Relay output Analog output Analog inputs ≥ 4.7 Ω RS-485 Expansion port Mounting and environment Degree of protection IP20 Mounting Wall mounting, side-by-side mounting, push-through mounting for FSB, FSC, FSD and FSE Cooling n n FSA up to 0.75 kW: convection cooling FSA up to FSE: power electronics cooled using heat sinks with external fan Ambient temperature In operation n –10 … 60° C (14 … 140° F) n 40 … 60° C (104 … 140° F) with derating In Storage n –40 ... 70° C (–40 ... 158° F) Relative humidity 95% (non-condensing) Altitude n Up to 4000 m above sea level n 1000 ... 4000 m: output current derating n 2000 ... 4000 m: supply voltage derating n Unshielded cable: 50 m for FSA up to FSD, 100 m for FSE n Shielded cable: 25 m for FSA up to FSD, 50 m for FSE n Longer motor cables possible with output reactor (see options) Motor cable length Dynamic braking Option module for FSA, FSB and FSC; integrated for FSD and FSE 11 Dimensions SINAMICS V20 drive W2 D Width (mm) H2 H3 H1 W1 Depth (mm) Weight (kg) H1 Height (mm) H2 H3 D WT approx. 90 – 140 150 145.5 1 90 166 140 150 145.5 1.05 127 140 160 135 – 164.5 1.8 Frame size W1 W2 FSA without fan 79 FSA 79 FSB FSC 170 184 182 140 – 169 2.6 FSD 223 240 206.5 166 – 172.5 4.3 FSE 228 245 264.5 206 – 209 6.6 V20 Basic Operator Panel (BOP) 31.5 Basic Operator Panel (BOP) interface 66.9 91 28.7 21.9 89.9 3.7 17 36.6 81.7 57 97 35 3. 5 drill pattern Parameter loader 35 89.9 57 OPEN 28.2 12 BOP 1AC 230V options Braking resistors Prated (HO) kW 1AC 230 V 0.12 FS W A 72 230 43.5 1.1 B 149 239 2.2 C 185 285 0.25 0.37 0.55 0.75 1.5 3 H D 150 WT 1 Line reactors W H 75.5 200 Output reactors Braking module Line filter class B D WT W H D WT W H D WT W 50 1.4 75 200 50 1.3 90 150 88 0.71 73 200 43.5 0.5 80 4.1 149 213 50.5 1.6 150 213 2.2 150 213 3.8 185 245 5.1 185 245 H 6.6 D WT 1 – 3AC 400V options Braking resistors Prated (LO) kW 3AC 400 V 0.37 0.55 FS W H A 105 295 105 D WT Line reactors W Output reactors Braking module Line filter class B H D WT W H D WT W H D WT W H D WT 100 1.48 125 120 71 1.1 207 175 73 3.4 90 150 80 0.71 73 202 65 1.75 345 100 1.80 125 140 71 2.1 207 180 73 3.9 175 345 100 2.73 125 145 91 2.95 247 215 100 10.1 100 297 85 4 250 490 140 6.20 140 359 95 7.3 270 515 175 260 180 600 7.3 0.75 1.1 1.5 2.2 3 B 5.5 C 4 7.5 11 15 22 D E 7.4 190 300 220 620 91 85 7.8 257 235 9.5 250 280 115 11.2 integrated 250 11.3 30 320 800 95 17 FS = frame size, WT = weight in kg, W = width in mm, H = height in mm, D = depth in mm 335 200 175 7.5 Simple entry using the DT Configurator The DT Configurator supports you with: n Selecting the drive based upon the application n The subsequent ordering process DT Configurator supplies you with: n A drive that is tailored to your requirements n 2D / 3D models n Operating instructions n Data sheets You can directly order the selected components through the Industry Mall — the Siemens e-commerce website — and without having to duplicate entries. In order to avoid making ordering mistakes, the order number is checked to ensure that it is correct. SINAMICS SELECTOR app — find part numbers quickly and easily Scan this QR code to download our SINAMICS SELECTOR app free-of-charge siemens.com/dt-configurator 13 Ordering information 1AC 230V Rated data Prated (HO) kW IH hp Part number A Fans 0.12 1/6 0.9 6SL3210-5BB11-2 V0 – 0.25 1/3 1.7 6SL3210-5BB12-5 V0 – 0.37 1/2 2.3 6SL3210-5BB13-7 V0 – 0.55 3/4 3.2 6SL3210-5BB15-5 V0 – 0.75 3/4 3.9 6SL3210-5BB17-5 V0 – 0.75 1 4.2 6SL3210-5BB18-0 V0 1 1.1 1–1/2 6 6SL3210-5BB21-1 V0 1 1.5 2 7.8 6SL3210-5BB21-5 V0 1 2.2 3 11 6SL3210-5BB22-2 V0 1 3 4 13.6 6SL3210-5BB23-0 V0 1 Frame size FSA FSB FSC EMC Standards With integrated line filter category C26) A Without integrated filter U 1AC 230V options FS A Prated (HO) kW Shield Braking resistor Line reactor Output reactor connection kit 6SE6400-... 6SE6400-... 6SE6400-... 6SL3266-... 0.12 Corresponding to the IEC standard Line filter class B³) 6SE6400-... Part number 3RV2011-1DA10 3NA3803 3NA3803 3RV2011-1FA10 10 3NA3803 3RV2011-1HA10 0.55 10 3NA3803 3RV2011-1JA10 0.75 16 3NA3805 3RV2011-1KA10 20 3NA3807 3RV2021-4BA10 32 3NA3812 3RV2021-4CA10 35 3NA3814 3RV2021-4EA10 50 3NA3820 3RV1031-4FA10 3CC00-4AB3 3TC00-4AD3 1AA00-0VA0 2FL01-0AB0 1.1 3CC01-0AB3 4BC11-2BA0 3CC02-6BB3 3TC01-0BD3 1AB00-0VA0 – 1.5 2.2 3 1AC00-0VA0 4BC12-5CA0 3CC03-5CB3 3TC03-2CD3 Accessories Spare parts Name Part number Replacement fan Parameter loader 6SL3255-0VE00-0UA0 Frame size Part number BOP (Basic Operator Panel) interface 6SL3255-0VA00-2AA0 FSA 6SL3200-0UF01-0AA0 FSB 6SL3200-0UF02-0AA0 FSC 6SL3200-0UF03-0AA0 Braking module 1AC 230V: 8A n 3AC 400V: 7A 6SL3201-2AD20-8VA0 n 14 Part number 10 0.37 C Current in A Circuit breaker⁴) 10 4BC05-0AA0 0.25 B Standard fuse⁴) V20 BOP (Basic Operator Panel) 6SL3255-0VA00-4BA0 BOP cable 3 m incl. 4 mounting screws 6SL3256-0VP00-0VA0 SINAMICS Memory Card (SD) 512 MB 6SL3054-4AG00-2AA0 RS485 Terminators (50 pieces) 6SL3255-0VC00-0HA0 SINAMICS V20 training case 6AG1067-2AA00-0AB6 DIN Rail mounting kit FSA: 6SL3261-1BA00-0AA0⁵) FSB: 6SL3261-1BB00-0AA0 FSD 6SL3200-0UF04-0AA0 FSE 6SL3200-0UF05-0AA0 3AC 400V Rated data Prated (LO) kW IL 400 V¹) IL 480 V A A hp Prated (HO) kW hp IH 400 V²) IH 480 V A A Part number Fans Frame size FSA 0.37 1/2 1.3 1.3 0.37 1/2 1.3 1.3 6SL3210-5BE13-7 V0 – 0.55 3/4 1.7 1.7 0.55 3/4 1.7 1.7 6SL3210-5BE15-5 V0 – 0.75 1 2.2 2.2 0.75 1 2.2 2.2 6SL3210-5BE17-5 V0 – 1.1 1–1/2 3.1 3.1 1.1 1–1/2 3.1 3.1 6SL3210-5BE21-1 V0 1 1.5 2 4.1 4.1 1.5 2 4.1 4.1 6SL3210-5BE21-5 V0 1 2.2 3 5.6 4.8 2.2 3 5.6 4.8 6SL3210-5BE22-2 V0 1 3 4 7.3 7.3 3 4 7.3 7.3 6SL3210-5BE23-0 V0 1 4 5 8.8 8.24 4 5 8.8 8.24 6SL3210-5BE24-0 V0 1 5.5 7–1/2 12.5 11 5.5 7–1/2 12.5 11 6SL3210-5BE25-5 V0 1 FSC 7.5 10 16.5 16.5 7.5 10 16.5 16.5 6SL3210-5BE27-5 V0 2 FSD 11 15 25 21 11 15 25 21 6SL3210-5BE31-1 V0 2 15 20 31 31 15 20 31 31 6SL3210-5BE31-5 V0 2 22 30 45 40 18.5 25 38 34 6SL3210-5BE31-8 V0 2 30 40 60 52 22 30 45 40 6SL3210-5BE32-2 V0 2 FSB FSE EMC Standards With integrated line filter category C3 7) C Without integrated filter U 3AC 400V options FS FSA FSB Prated (LO) kW Prated (HO) kW 0.37 0.37 0.55 0.55 0.75 Braking resistor Line reactor 6SL3201-... 6SL3203-... Shield connection kit 6SL3266-... Line filter class B3) 6SL3203-... 0AE16-1CA0 1AA00-0VA0 0BE17-7BA0 Standard fuse⁴) Circuit breaker⁴) Current in A Part number 6 3NA3801 3RV2011-1CA10 6 3NA3801 3RV2011-1DA10 0.75 6 3NA3801 3RV2011-1EA10 1.1 1.1 6 3NA3801 3RV2011-1FA10 1.5 1.5 10 3NA3803 3RV2011-1HA10 2.2 2.2 16 3NA3805 3RV2011-1JA10 3 3 4 4 FSC 5.5 5.5 FSD 7.5 7.5 11 11 15 15 0BE14-3AA0 22 18.5 30 22 0CE13-2AA0 0CE21-0AA0 0BE21-0AA0 0AE18-8CA0 0BE21-8AA0 0CE21-8AA0 0AE23-8CA0 0BE23-8AA0 4BD21-2DA0 16 3NA3805 3RV2011-1KA10 3NA3807 3RV2021-4AA10 1AC00-0VA0 32 3NA3812 3RV2021-4BA10 1AD00-0VA0 – – 3VL1103-1KM30-0AA0 – – 3VL1104-1KM30-0AA0 – – 3VL1105-1KM30-0AA0 63 3NA3022 3VL1108-1KM30-0AA0 80 3NA3024 3VL1108-1KM30-0AA0 0BE21-8BA0 0BE23-8BA0 0CE23-8AA0 6SE6400-… 6SE6400-… 6SL3266-… 3CC05-2DD0 3TC05-4DD0 1AE00-0VA0 3CC08-3ED0 Part number 20 1AB00-0VA0 0AE21-8CA0 6SE6400-… FSE Corresponding to the IEC standard Output reactor 6SL3202-... 6SL3203-… 0BE23-8BA0 0BE27-5BA0 ¹⁾ The output current IL is based on the duty cycle for low overload (LO). ²⁾ The output current IH is based on the duty cycle for high overload (HO). ³⁾ See specification of EMC standards, page 10 ⁴⁾ Additional information about the listed fuses and circuit breakers can be found in Catalogs LV 10, IC 10 and IC 10 AO siemens.com/drives/infocenter ⁵⁾ Installation of FSA with fan — please refer to SINAMICS V20 manual. 6 ⁾ EN61800-3 Catagory C2, 1st environment (residential domestic) 7 ⁾ EN61800-3 Catagory C3, 2nd environment (industry) 15 There’s more to it usa.siemens.com/sinamics Everything about our drive family can be found online. SINAMICS — one family, one source, all applications Siemens Industry, Inc. 5300 Triangle Parkway, Suite 100 Norcross, GA 30092 1-800-879-8079 [email protected] usa.siemens.com/motioncontrol Order No. DRBR-V2001-0415 Printed in USA © 2015 Siemens Industry, Inc. This brochure contains only general descriptions or performance features, which do not always apply in the manner described in concrete application situations or may change as the products undergo further development. Performance features are valid only if they are formally agreed upon when the contract is closed. Siemens is a registered trademark of Siemens AG. Product names mentioned may be trademarks or registered trademarks of their respective companies. Specifications are subject to change without notice.