PD- 95084A
IRLR/U2905PbF
l
l
l
l
l
l
l
l
Logic-Level Gate Drive
Ultra Low On-Resistance
Surface Mount (IRLR2905)
Straight Lead (IRLU2905)
Advanced Process Technology
Fast Switching
Fully Avalanche Rated
Lead-Free
HEXFET® Power MOSFET
D
VDSS = 55V
RDS(on) = 0.027Ω
G
ID = 42A
S
Description
Fifth Generation HEXFETs from International Rectifier utilize advanced
processing techniques to achieve the lowest possible on-resistance per
silicon area. This benefit, combined with the fast switching speed and
ruggedized device design that HEXFET Power MOSFETs are well known for,
provides the designer with an extremely efficient device for use in a wide
variety of applications.
The D-PAK is designed for surface mounting using vapor phase, infrared, or
wave soldering techniques. The straight lead version (IRFU series) is for
through-hole mounting applications. Power dissipation levels up to 1.5 watts
are possible in typical surface mount applications.
D-Pak
TO-252AA
I-Pak
TO-251AA
Absolute Maximum Ratings
Parameter
ID @ TC = 25°C
ID @ TC = 100°C
IDM
PD @TC = 25°C
VGS
EAS
IAR
EAR
dv/dt
TJ
TSTG
Continuous Drain Current, VGS @ 10V
Continuous Drain Current, VGS @ 10V
Pulsed Drain Current
Power Dissipation
Linear Derating Factor
Gate-to-Source Voltage
Single Pulse Avalanche Energy
Avalanche Current
Repetitive Avalanche Energy
Peak Diode Recovery dv/dt
Operating Junction and
Storage Temperature Range
Soldering Temperature, for 10 seconds
Max.
Units
42
30
160
110
0.71
± 16
210
25
11
5.0
-55 to + 175
A
W
W/°C
V
mJ
A
mJ
V/ns
°C
300 (1.6mm from case )
Thermal Resistance
Parameter
RθJC
RθJA
RθJA
Junction-to-Case
Case-to-Ambient (PCB mount)**
Junction-to-Ambient
Typ.
Max.
Units
–––
–––
–––
1.4
50
110
°C/W
** When mounted on 1" square PCB (FR-4 or G-10 Material ) .
For recommended footprint and soldering techniques refer to application note #AN-994
www.irf.com
1
12/7/04
IRLR/U2905PbF
Electrical Characteristics @ TJ = 25°C (unless otherwise specified)
∆V(BR)DSS/∆TJ
Parameter
Drain-to-Source Breakdown Voltage
Breakdown Voltage Temp. Coefficient
RDS(on)
Static Drain-to-Source On-Resistance
VGS(th)
gfs
Gate Threshold Voltage
Forward Transconductance
IDSS
Drain-to-Source Leakage Current
V(BR)DSS
Qg
Qgs
Qgd
td(on)
tr
td(off)
tf
Gate-to-Source Forward Leakage
Gate-to-Source Reverse Leakage
Total Gate Charge
Gate-to-Source Charge
Gate-to-Drain ("Miller") Charge
Turn-On Delay Time
Rise Time
Turn-Off Delay Time
Fall Time
LD
Internal Drain Inductance
LS
Internal Source Inductance
Ciss
Coss
Crss
Input Capacitance
Output Capacitance
Reverse Transfer Capacitance
IGSS
Min. Typ. Max. Units
Conditions
55
––– –––
V
VGS = 0V, ID = 250µA
––– 0.070 ––– V/°C Reference to 25°C, I D = 1mA
–––
––– 0.027
VGS = 10V, ID = 25A
–––
––– 0.030
W
VGS = 5.0V, ID = 25A
–––
––– 0.040
VGS = 4.0V, ID = 21A
1.0
––– 2.0
V
VDS = VGS, ID = 250µA
21
––– –––
S
VDS = 25V, ID = 25A
–––
––– 25
VDS = 55V, VGS = 0V
µA
–––
––– 250
VDS = 44V, VGS = 0V, TJ = 150°C
–––
––– 100
VGS = 16V
nA
–––
––– -100
VGS = -16V
–––
––– 48
ID = 25A
–––
––– 8.6
nC
VDS = 44V
–––
––– 25
VGS = 5.0V, See Fig. 6 and 13
–––
11 –––
VDD = 28V
–––
84 –––
ID = 25A
ns
–––
26 –––
RG = 3.4Ω, VGS = 5.0V
–––
15 –––
RD = 1.1Ω, See Fig. 10
Between lead,
4.5
nH
6mm (0.25in.)
G
from package
––– 7.5 –––
and center of die contact
––– 1700 –––
VGS = 0V
–––
400 –––
pF
VDS = 25V
–––
150 –––
ƒ = 1.0MHz, See Fig. 5
D
S
Source-Drain Ratings and Characteristics
IS
ISM
VSD
trr
Qrr
ton
Parameter
Continuous Source Current
(Body Diode)
Pulsed Source Current
(Body Diode)
Diode Forward Voltage
Reverse Recovery Time
Reverse RecoveryCharge
Forward Turn-On Time
Min. Typ. Max. Units
Conditions
D
MOSFET symbol
––– ––– 42
showing the
A
G
integral reverse
––– ––– 160
S
p-n junction diode.
––– ––– 1.3
V
TJ = 25°C, IS = 25A, VGS = 0V
––– 80
120
ns
TJ = 25°C, IF = 25A
––– 210 320
nC
di/dt = 100A/µs
Intrinsic turn-on time is negligible (turn-on is dominated by LS+LD)
Notes:
Repetitive rating; pulse width limited by
max. junction temperature. ( See fig. 11 )
VDD = 25V, starting TJ = 25°C, L =470µH
RG = 25Ω, IAS = 25A. (See Figure 12)
ISD ≤ 25A, di/dt ≤ 270A/µs, VDD ≤ V(BR)DSS,
TJ ≤ 175°C
Pulse width ≤ 300µs; duty cycle ≤ 2%.
2
Caculated continuous current based on maximum allowable
junction temperature;
Package limitation current = 20A.
This is applied for I-PAK, LS of D-PAK is measured between
lead and center of die contact.
Uses IRLZ44N data and test conditions.
www.irf.com
IRLR/U2905PbF
1000
1000
VGS
15V
12V
10V
8.0V
6.0V
4.0V
3.0V
BOTTOM 2.5V
100
10
2.5V
20µs PULSE WIDTH
T J = 25°C
1
0.1
1
10
100
10
A
100
3.0
R DS(on) , Drain-to-Source On Resistance
(Normalized)
I D , Drain-to-Source Current (A)
TJ = 25°C
100
TJ = 175°C
10
V DS= 25V
20µs PULSE WIDTH
4.0
5.0
6.0
7.0
8.0
1
10
9.0
A
I D = 41A
2.5
2.0
1.5
1.0
0.5
VGS = 10V
0.0
-60 -40 -20
0
20
40
60
A
80 100 120 140 160 180
VGS , Gate-to-Source Voltage (V)
TJ , Junction Temperature (°C)
Fig 3. Typical Transfer Characteristics
Fig 4. Normalized On-Resistance
Vs. Temperature
www.irf.com
A
100
Fig 2. Typical Output Characteristics
1000
3.0
20µs PULSE WIDTH
T J = 175°C
VDS , Drain-to-Source Voltage (V)
Fig 1. Typical Output Characteristics
1
2.5V
1
0.1
VDS , Drain-to-Source Voltage (V)
2.0
VGS
15V
12V
10V
8.0V
6.0V
4.0V
3.0V
BOTTOM 2.5V
TOP
ID , Drain-to-Source Current (A)
ID , Drain-to-Source Current (A)
TOP
3
IRLR/U2905PbF
2400
Ciss
15
V GS = 0V,
f = 1MHz
C iss = Cgs + C gd , Cds SHORTED
C rss = C gd
C oss = Cds + C gd
VGS , Gate-to-Source Voltage (V)
2800
C, Capacitance (pF)
2000
1600
Coss
1200
800
Crss
400
0
1
10
100
I D = 25A
V DS = 44V
V DS = 28V
12
9
6
3
FOR TEST CIRCUIT
SEE FIGURE 13
0
A
0
VDS , Drain-to-Source Voltage (V)
20
30
40
50
60
70
A
Q G , Total Gate Charge (nC)
Fig 6. Typical Gate Charge Vs.
Gate-to-Source Voltage
Fig 5. Typical Capacitance Vs.
Drain-to-Source Voltage
1000
1000
OPERATION IN THIS AREA LIMITED
BY R DS(on)
I D , Drain Current (A)
ISD , Reverse Drain Current (A)
10
100
TJ = 175°C
10µs
100µs
10
1ms
TJ = 25°C
VGS = 0V
10
0.4
4
100
0.8
1.2
1.6
2.0
A
2.4
TC = 25°C
TJ = 175°C
Single Pulse
1
1
10ms
A
10
100
VSD , Source-to-Drain Voltage (V)
VDS , Drain-to-Source Voltage (V)
Fig 7. Typical Source-Drain Diode
Forward Voltage
Fig 8. Maximum Safe Operating Area
www.irf.com
IRLR/U2905PbF
50
LIMITED BY PACKAGE
VGS
40
ID , Drain Current (A)
RD
V DS
D.U.T.
RG
30
+
-VDD
5V
Pulse Width ≤ 1 µs
Duty Factor ≤ 0.1 %
20
Fig 10a. Switching Time Test Circuit
10
VDS
90%
0
25
50
75
100
125
150
175
TC , Case Temperature ( °C)
10%
VGS
Fig 9. Maximum Drain Current Vs.
Case Temperature
td(on)
tr
t d(off)
tf
Fig 10b. Switching Time Waveforms
Thermal Response (Z thJC )
10
1
D = 0.50
0.20
0.10
0.1
PDM
0.05
0.02
0.01
t1
SINGLE PULSE
(THERMAL RESPONSE)
t2
Notes:
1. Duty factor D = t 1 / t 2
2. Peak T J = P DM x Z thJC + TC
0.01
0.00001
0.0001
0.001
0.01
0.1
t1 , Rectangular Pulse Duration (sec)
Fig 11. Maximum Effective Transient Thermal Impedance, Junction-to-Case
www.irf.com
5
15V
L
VDS
D.U.T
RG
IAS
20V
DRIVER
+
V
- DD
0.01Ω
tp
Fig 12a. Unclamped Inductive Test Circuit
A
E AS , Single Pulse Avalanche Energy (mJ)
IRLR/U2905PbF
500
TOP
BOTTOM
400
ID
10A
17A
25A
300
200
100
0
VDD = 25V
25
50
A
75
100
125
150
175
Starting TJ , Junction Temperature (°C)
V(BR)DSS
tp
Fig 12c. Maximum Avalanche Energy
Vs. Drain Current
I AS
Current Regulator
Same Type as D.U.T.
Fig 12b. Unclamped Inductive Waveforms
50KΩ
QG
10 V
QGS
.3µF
D.U.T.
QGD
+
V
- DS
VGS
VG
3mA
Charge
Fig 13a. Basic Gate Charge Waveform
6
12V
.2µF
IG
ID
Current Sampling Resistors
Fig 13b. Gate Charge Test Circuit
www.irf.com
IRLR/U2905PbF
Peak Diode Recovery dv/dt Test Circuit
+
D.U.T
Circuit Layout Considerations
• Low Stray Inductance
• Ground Plane
• Low Leakage Inductance
Current Transformer
+
-
-
+
RG
•
•
•
•
Driver Gate Drive
P.W.
+
dv/dt controlled by RG
Driver same type as D.U.T.
ISD controlled by Duty Factor "D"
D.U.T. - Device Under Test
Period
D=
-
VDD
P.W.
Period
VGS=10V
*
D.U.T. ISD Waveform
Reverse
Recovery
Current
Body Diode Forward
Current
di/dt
D.U.T. VDS Waveform
Diode Recovery
dv/dt
Re-Applied
Voltage
Body Diode
VDD
Forward Drop
Inductor Curent
Ripple ≤ 5%
ISD
* VGS = 5V for Logic Level Devices
Fig 14. For N-Channel HEXFETS
www.irf.com
7
IRLR/U2905PbF
D-Pak (TO-252AA) Package Outline
Dimensions are shown in millimeters (inches)
D-Pak (TO-252AA) Part Marking Information
EXAMPLE: T HIS IS AN IRFR120
WITH AS S EMBLY
LOT CODE 1234
AS S EMBLED ON WW 16, 1999
IN THE AS S EMBLY LINE "A"
PART NUMBER
INTERNATIONAL
RECTIFIER
LOGO
Note: "P" in as sembly line pos ition
indicates "Lead-Free"
IRFU120
12
916A
34
AS S EMBLY
LOT CODE
DAT E CODE
YEAR 9 = 1999
WEEK 16
LINE A
OR
INT ERNAT IONAL
RECT IFIER
LOGO
PART NUMBER
IRFU120
12
AS S EMBLY
LOT CODE
8
34
DATE CODE
P = DES IGNAT ES LEAD-FREE
PRODUCT (OPT IONAL)
YEAR 9 = 1999
WEEK 16
A = AS S EMBLY S ITE CODE
www.irf.com
IRLR/U2905PbF
I-Pak (TO-251AA) Package Outline
Dimensions are shown in millimeters (inches)
I-Pak (TO-251AA) Part Marking Information
EXAMPLE: T HIS IS AN IRFU120
WIT H AS S EMBLY
LOT CODE 5678
AS S EMBLED ON WW 19, 1999
IN T HE AS S EMBLY LINE "A"
INT ERNAT IONAL
RECT IFIER
LOGO
PART NUMBER
IRF U120
919A
56
78
AS S EMBLY
LOT CODE
Note: "P" in assembly line
position indicates "Lead-Free"
DAT E CODE
YEAR 9 = 1999
WEEK 19
LINE A
OR
INT ERNAT IONAL
RECT IFIER
LOGO
PART NUMBER
IRFU120
56
AS S EMBLY
LOT CODE
www.irf.com
78
DAT E CODE
P = DES IGNAT ES LEAD-FREE
PRODUCT (OPT IONAL)
YEAR 9 = 1999
WEEK 19
A = AS S EMBLY S IT E CODE
9
IRLR/U2905PbF
D-Pak (TO-252AA) Tape & Reel Information
Dimensions are shown in millimeters (inches)
TR
TRR
16.3 ( .641 )
15.7 ( .619 )
12.1 ( .476 )
11.9 ( .469 )
FEED DIRECTION
TRL
16.3 ( .641 )
15.7 ( .619 )
8.1 ( .318 )
7.9 ( .312 )
FEED DIRECTION
NOTES :
1. CONTROLLING DIMENSION : MILLIMETER.
2. ALL DIMENSIONS ARE SHOWN IN MILLIMETERS ( INCHES ).
3. OUTLINE CONFORMS TO EIA-481 & EIA-541.
13 INCH
16 mm
NOTES :
1. OUTLINE CONFORMS TO EIA-481.
IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105
TAC Fax: (310) 252-7903
Visit us at www.irf.com for sales contact information.
Data and specifications subject to change without notice. 12/04
10
www.irf.com
Note: For the most current drawings please refer to the IR website at:
http://www.irf.com/package/