JULY 2000 NEW! L 30W CCF esign Inverter D ML4877* LCD Desktop Backlight Lamp Driver GENERAL DESCRIPTION FEATURES The ML4877 is an ideal solution for driving multiple cold cathode fluorescent tubes (CCFL) used in liquid crystal display (LCD) backlight applications. It provides dimming ballast control for the LCD display. ■ Ideal for 30W inverter designs, 1 to 8 lamp design ■ PWM dimming capability ■ Backlight lamp driver with differential drive ■ Up to 30% lower power for same light output ■ Low standby current (<10µA) ■ Improved efficiency (»95%) ■ Allows all N-channel MOSFET drive ■ Adjustable lamp out detect with latch ■ Resonant threshold detection and synchronous rectification ■ Positive input for dimming control By utilizing differential drive the ML4877 can deliver the same light output with significantly less input power compared to existing single ended drive schemes. Improvements as high as 30% can be realized when using low power lamps and advanced LCD screen housings. This increased light output is achieved because the differential drive configuration is much less sensitive, and therefore less power is wasted in the capacitive parasitics that exist in the backlight housing. An additional benefit of this configuration is an even distribution of light. The IC includes an adjustable lamp out detect circuit that latches the IC off when a lamp fault is detected. Also, the unique architecture of the ML4877 allows the development of a backlight system that will inherently meet the UL requirements for safety. The ML4877 is optimized for large LCD applications applications where high efficiency is critical to maximize battery life. The high efficiency is achieved by a resonant scheme with zero voltage switching. * THIS PART IS END OF LIFE AS OF JULY 1, 2000 BLOCK DIAGRAM AZR 2 B ON 19 VDD 13 B SYNC OUT 11 B OFF 20 VDD HVDD 12 VREF 5 10 L RTD LINEAR REGULATOR DR3 MASTER BIAS & UVLO DR1 DR1 DR2 14 L GATE 1 DR2 16 L GATE 2 Q ONE SHOT NEG EDGE DELAY S Q T Q R Q 6 L ILIM 8 LEA OUT – 7 LEA– + 1 LEA+ + – 0.5V ON/OFF 15 RESONANT THRESHOLD DETECTOR SS Q S Q R + – VDD CLK – + OSCILLATOR SS 17 18 4 9 3 PGND GND RT CT SS CAP 1 ML4877 PIN CONFIGURATION ML4877 20-Pin SSOP (R20) LEA+ 1 20 B OFF AZR 2 19 B ON SS CAP 3 18 GND RT 4 17 PGND VREF 5 16 L GATE 2 L ILIM 6 15 ON/OFF LEA– 7 14 L GATE 1 LEA OUT 8 13 VDD CT 9 12 HVDD L RTD 10 11 B SYNC OUT TOP VIEW PIN DESCRIPTION PIN NAME FUNCTION PIN NAME FUNCTION 1 LEA+ Positive input for lamp error amp 11 B SYNC OUT Output of MOSFET driver to gate of synchronous FET catch diode. 2 AZR Connection to gate of external FET for high voltage regulator. Internally a zener diode to ground. 12 HVDD Battery power input to linear regulator 13 VDD Output of linear regulator. Positive power for IC. 14 L GATE1 Output of MOSFET driver. Connection to gate of one side of inverter FET drive pair. 15 ON/OFF Logic input for chip 16 L GATE2 Output of MOSFET driver. Connection to gate of one side of inverter FET drive pair. 3 SS CAP Connection of optional external soft start capacitor 4 RT Oscillator timing resistor 5 VREF Voltage reference output 6 L ILIM Input to current limit amplifier 7 LEA- Negative input for lamp error amplifier 8 LEA OUT Output of lamp error amplifier. External compensation capacitor connects between this pin and LEA. 17 PGND Power ground 18 GND Signal ground 19 B ON Connection to primary side of gate pulse transformer 20 B OFF Output of MOSFET driver. Connection to gate of FET that disables the input power. 9 CT Oscillator timing capacitor 10 L RTD Input to resonant threshold detector 2 ML4877 ABSOLUTE MAXIMUM RATINGS Voltage on HVIDD .................................................... 20V Current into L RTD ............................................... ±10mA Junction Temperature .............................................. 150ºC Storage Temperature Range ....................... -65ºC to 150ºC Lead Temperature (Soldering 10 sec.) ..................... 260ºC Thermal Resistance (qJA) .................................... 100ºC/W Absolute maximum ratings are those values beyond which the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied. Supply Current (ICC) ............................................... 75mA Output Current, Source or Sink ............................. 250mA Voltage on Pins LEA+, AZR, SS CAP, RT, VREF, L ILIM, LEA-, LEA OUT, CT, B SYNC OUT, VDD, L GATE 1, ON/OFF, L GATE 2, PGND, GND, B ON, B OFF ............................... –0.3V to VDD +0.3V OPERATING CONDITIONS Temperature Range ML4877C ................................................... 0ºC to 70ºC ML4877E...............................................–20ºC to 70ºC ELECTRICAL CHARACTERISTICS Unless otherwise specified, VDD = 5V ±5%, TA= Operating Temperature Range, CT = 47pF, RT = 82kW (Note 1) SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS 60 70 dB CURRENT REGULATOR ERROR AMPLIFIER Open Loop Gain Output High ILOAD = 5µA Output Low ILOAD = 25µA 2.8 3.0 0.4 Bandwidth (-3dB) V 0.7 1 Common Mode Voltage Range 0 MHz 1.0 V 50 100 nA -5 0 5 mv 750 950 nA 2.5 V 500 550 mV Input Bias Current Input Offset Voltage V Soft Start Charge Current VSSCAP = 1V 550 Soft Start Threshold (LEA OUT) VSSCAP = 1V 2 CURRENT LIMIT COMPARATOR Current Threshold 450 Input Bias Current VILIM = 0.1V 50 100 nA Propagation Delay (Note 2) 150 250 ns OUTPUT DRIVERS Output High - B SYNC OUT, B OFF VDD 5V, ILOAD = 12mA 4.625 Output Low - B SYNC OUT, B OFF ILOAD 12mA 0.2 0.375 V Rise & Fall time - B SYNC OUT, B OFF CLOAD =100pF 20 50 ns Output High - B ON VDD 5V, ILOAD = 12mA Output Low - B ON ILOAD 50mA 0.2 0.375 V Fall Time - B ON CLOAD = 2400pF (Note 2) 45 80 ns 150 200 ns 4.625 4.8 V 4.8 V ONE SHOT Pulse Width 100 3 ML4877 ELECTRICAL CHARACTERISTICS SYMBOL (Continued) PARAMETER CONDITIONS MIN TYP MAX UNITS 20 35 55 ns 68 80 92 kHz 500 700 900 µA Peak Voltage 2.3 2.5 2.7 V Valley Voltage 0.8 1 1.2 V 4.625 4.8 DELAY TIMER Delay Time HIGH VOLTAGE INVERTER Oscillator Nominal Frequency Discharge Current VCT = 2V Output Drivers Output High - L GATE 1, 2 VDD = 5V, ILOAD 12mA V Output Low - L GATE 1, 2 ILOAD = 50mA 0.2 0.375 V Rise & Fall Time - L GATE 1, 2 CLOAD =1000pF 20 50 ns Resonant Threshold Detector Threshold 0.45 0.8 1.15 V Hysteresis 0.15 03 0.45 mV -2 VDD 2 % Lamp Out Detect Threshold Latch Inhibit Threshold (SSCAP) LRTD > VDD + 0.1V 2.5 V Under Voltage Detector Start Up Threshold 3.8 4.1 4.4 V Hysteresis 150 300 450 mV Logic Interface (ON/OFF) V IH 2.5 V VIL Input Bias Current 0.5 ON/OFF = 3V V 10 25 µA Linear Regulator Aux Zener Reference Voltage (AZR) IAZR = 10µA 12.3 13.5 14.7 V Regulator Voltage (VDD) HVDD = 12V 4.75 5.0 5.35 V Regulator Source Current External to device 10 Drop Out Voltage IHVDD = 1mA 30 90 mA Drop Out Voltage lHVDD = 5mA 125 275 mA 18 V HVDD Input Voltage Range 4 5 mA ML4877 ELECTRICAL CHARACTERISTICS SYMBOL (Continued) PARAMETER CONDITIONS MIN TYP MAX UNITS 375 450 µA 1 10 µA 10 20 mV 2.5 2.53 V 20 30 mV 2.5 2.535 V BIAS VDD Supply Current ON/OFF = “I”, no load VDD Supply Current ON/OFF = “0”, HVDD = 12V VREF Load Regulation ILOAD = 25µA VREF Output Voltage TA = 25ºC 2.47 VREF Line Regulation VREF Line, Load, Temp 2.465 Note 1: Limits are guaranteed by 100% testing, sampling, or correlation with worst case test conditions. Note 2: Actual load is 1200pF. The 2:1 transformer reflects an effective 2400pF. 5 ML4877 U2-A 5 TO 18V IN *OPTIONAL SEE NOTE C7 C8 R1 T2 D1 U2-B Q2 C1 OR OPTIONAL C9 L1 100µh Q1 R7 10k 2 VDD 13 B ON 19 B ON 20 B SYNC 11 T1 L RTD VDD HVDD 12 DR3 DR1 DR1 ONE SHOT VREF C3 1.0µF S Q S Q C6 DR2 GATE1 14 DR2 GATE2 16 0.1µF Q NEG EDGE DELAY MASTER BIAS & UVLO 5 39pF 10 LINEAR REGULATOR T Q Q4 L ILIM 6 + R6 O.5Ω – 0.5V ON/OFF LEA OUT 8 15 1 – + + – R – Q VDD + S RESONANT THRESHOLD DETECTOR 7 R5 100kΩ SS CLK 17 PGND OSCILLATOR 18 4 GND RT R2 82kΩ 9 3 CT C5 47pF SS CAP C2 0.1µF Figure 1. Typical Application Schematic for the ML4877 6 R6 100k C4 LEA– 0.047µF SS Q C11 LAMP AZR R4 1.6MΩ ML4877 FUNCTIONAL DESCRIPTION The ML4877 consists of a PWM regulator, a lamp driver/ inverter, a linear regulator and control circuits. This IC, in conjunction with external components, converts a DC battery voltage into the high voltage and high frequency AC signal required to start and drive miniature cold cathode fluorescent lamps. Typical application circuits are shown in Figure 1 and Figure 5. Note: Please read the Power Sequencing section below prior to using the ML4877. LAMP DRIVER The lamp driver, sometimes referred to as a lamp inverter, is comprised of a PWM regulator and a Royer type inverter circuit to drive the lamp. The PWM regulator, in a buck configuration, controls the magnitude of the lamp current to provide the dimming capability. Figure 2 shows a simplified circuit to more easily illustrate the operation of the circuit. Due to the presence of the buck inductor, L1, the circuit shown in Figure 2 is essentially a current fed parallel loaded resonant circuit. Lm is the primary inductance of the output transformer, T1, which tunes with the resonant capacitor CR to set the resonant frequency of the inverter. The oscillator frequency is always set lower than the natural resonant frequency to ensure synchronization. The current source IC models the current through the buck inductor L1. The MOSFETs, (Q3 and Q4) are alternately turned on with a constant 50% duty cycle signal (L GATE1, L GATE2) at one-half the frequency of the oscillator. In this way each transistor pulses, or excites, the resonant tank on each half cycle. The combination of these two signals appear across the primary winding of the output transformer as a sinusoidal waveform. This voltage is multiplied by the step-up turns ratio of the output transformer and impressed across the lamp. The output transitions are controlled by feedback through the L RTD pin by sensing the voltage at the center tap of the output transformer. Each time this signal reaches the minimum resonant threshold detection point an internal clock pulse is generated to keep the system synchronized. Figure 3 shows some of these representative waveforms at the important nodes of the circuit. The PWM regulator is comprised of a MOSFET (U2-A), inductor L1, and the gate control and drive circuitry as shown in Figure 1. A signal with a constant pulse width of I 50ns is applied to the primary of the 2:1 pulse transformer T2, rectified by diode D1, and used to charge the gate capacitance of U2-A, thereby turning it on. The turn off is controlled by discharging this capacitance through MOSFET Q2. The pulse width of the signal on the gate of Q2 (B OFF) varies according to the difference of the amplitude of the feedback signal on LEA+, and LEA–. The signal on LEA– is proportional to the AC current flowing in the lamp, while the signal on LEA+ is a function of the brightness control setting. The AC lamp current feedback signal is developed by monitoring the current through resistor R6 in the common source connection of the inverter MOSFETs, Q3 and Q4. The lamp current, and therefore brightness, is adjusted by varying the voltage applied to R4, at the brightness adjust control point. Increasing this voltage increases the brightness. OSCILLATOR The frequency of the oscillator in the ML4877 is set by selecting the values Of CT and RT. Figure 4 shows the CT IC ➞ COUT T1 CLOCK T1 Lm Lm 1:N LAMP L GATE1 CR DRAIN-Q4 L GATE2 Q3 Q4 DRAIN-Q3 T1-CNTR-PRI SOURCE OF U2-A Figure 2. Kelvin Sense Connections Figure 3. Operating Waveforms of the Lamp Driver Section 7 ML4877 FUNCTIONAL DESCRIPTION (Continued) oscillator frequency versus the value of RT for different values Of CT. This nomograph may be used to select the appropriate value of RT and CT to achieve the desired oscillator frequency for the ML4877. By selecting the appropriate value the AC lamp current can be set to slowly increase with a controlled time constant. The capacitor value can be calculated according to the following formula. C = (3 X 10-7)TS LINEAR REGULATOR (1) A linear voltage regulator is provided to power the low voltage and low current control circuitry on the ML4877. This is typically used when there is no separate 5V supply available at the inverter board. For operation up to 18V, the linear regulator is used by connecting the HVDD pin to the input battery voltage. For operation over 18V, a MOSFET, and a resistor (Q and R1, Figure 1) are connected as shown. The MOSFET is required to stand off the high voltage. The AZR pin is just a zener diode to ground used to bias the gate of Q1. Where TS = Duration of the soft start sequence in seconds LAMP OUT DETECT It is important to observe correct power and logic input sequencing when powering up the ML4877. The following procedure must be observed to avoid damaging the device. In those cases when there is no lamp connected, or the connection is faulty, the output voltage of the lamp driver circuit will tend to rise to a high level in an attempt to start the nonexistent lamp. The lamp out detect circuit on the ML4877 will detect this condition by sensing a voltage proportional to the center tap voltage on the primary of the output transformer, T1 on the L RTD pin. The ration of resistors R7 and R8 sets the lamp out detect threshold. When the voltage on the L RTD pin exceeds VDD, an internal latch is set and the lamp driver goes into a shutdown mode. The logic control pin ON/OFF must be cycled low, then high to reset the latch and return the lamp driver to the normal state. The input to the lamp out latch is inhibited by the signal on the soft start pin. The latch will not be set until the voltage on SS CAP (pin 3) rises to more than 4.2V nominally. LOGIC CONTROL The ML4877 is controlled by a single logic input, ON/ OFF. A logic level high on this pin enables the lamp driver. A logic zero puts the circuit into a very low power state. POWER SEQUENCING 1. Apply the battery power to HVDD, or 2. If HVDD is not used. Apply the VDD voltage. With HVDD connected the VDD voltage is supplied by the internal regulator on the ML4877. 3. Apply a logic high to the ON/OFF input. Please refer to Application Note 32 for detailed application information beyond what is presented here. APPLICATIONS SECTION SOFT START HIGH POWER INVERTER The capability to control the start up behavior is achieved by setting the value of a single capacitor, C2 in Figure 1. The ML4877 is easily adapted to high power CCFL inverter designs. Figure 5 displays a schematic of a 30W ML4877 application. This particular design employs PWM dimming in order to extend dimming range. C = pF = 100 The 30W inverter design is ideal for applications between the 20W and 30W range. Deep dimming capability is achieved via PWM technique with no flicker and no popon effects. Uniform intensity can be maintained across 1 to 8 lamps to well below 5%. 30 C = pF 46 C Figure 6 provides a top view of an example of a ML4877 30W design. This design can be modified for 1 to 8 lamps and contains a PWM dimming interface using standard low cost components. C pF 81 FRQUENCY (kHz) 1000 = F 0p 12 10 10 100 1000 RESISTANCE (kΩ) Figure 4. Oscillator Frequency Nomograph 8 For the latest application notes and other information, visit the Micro Linear website at www.microlinear.com. ML4877 J2 J1 1 2 3 GND VDD DIMMING 3 T1 1 5 8 4, 10 L1 22µH Q4 IRF7416 F1 4A R17 20Ω C20 0.1µF C24 220µF C22 220µF C23 1nF R13 10kΩ R16 20Ω C18 1nF C13 1µF C17 4.7nF R4 6.2kΩ 1 2 3 4 5 6 7 8 9 10 LEA+ B OFF AZR B ON SS CAP GND RT ML4877 PGND VREF L GATE 2 L ILIM ON/OFF LEA– U2 L GATE 1 LEA OUT VDD CT HVDD L RTD B SYNC OUT 1 R2 10kΩ 3 + U1B 1 CR4 1N4148 R1 10kΩ R11 0.2Ω 1W R12 0.2Ω 1W 20 19 18 17 16 15 14 13 12 11 J3 C6 68pF 1kV C7 68pF 1kV C8 68pF 1kV C9 68pF 1kV 1 2 3 4 5 6 7 8 9 10 11 R3 10kΩ R9 143kΩ C14 C12 1µF 1µF CR1 5.1V J2 2 – Q2 IRLR2905 1 2 3 4 5 6 7 8 9 10 11 C16 47pF J1 2 Q1 IRLR2905 12 Q5 2N3904 R8 91kΩ 1 R6 7.5kΩ Q8 2N3906 Q6 2N3904 C19 4.7nF R7 10kΩ R5 30kΩ 9 CR5 C21 1nF R14 1kΩ CR6 SK34MSCT Q7 2N3904 R18 200Ω R15 1kΩ C1 0.22µF MKS-10 63V C2 68pF 1kV C3 68pF 1kV C4 68pF 1kV C5 68pF 1kV R6 390kΩ 5 6 CR2 1N4148 2 8 + – U1A 4 Q3 2N3906 C10 0.033µF CR3 1N4148 C15 1µF 7 C11 1µF R10 10kΩ PWM Control Figure 5. 30W Backlight CCFL Inverter with PWM Dimming 9 ML4877 Figure 6. 30W CCFL Inverter Board, 1 to 8 Lamps 10 ML4877 PHYSICAL DIMENSIONS inches (millimeters) Package: R20 20-Pin SSOP 0.279 - 0.289 (7.08 - 7.34) 20 0.205 - 0.213 (5.20 - 5.40) 0.301 - 0.313 (7.65 - 7.95) PIN 1 ID 1 0.026 BSC (0.65 BSC) 0.068 - 0.078 (1.73 - 1.98) 0º - 8º 0.066 - 0.070 (1.68 - 1.78) 0.009 - 0.015 (0.23 - 0.38) SEATING PLANE 0.002 - 0.008 (0.05 - 0.20) 0.022 - 0.038 (0.55 - 0.95) 0.004 - 0.008 (0.10 - 0.20) ORDERING INFORMATION © Micro Linear 1998. PART NUMBER TEMPERATURE RANGE PACKAGE ML4877CR (END OF LIFE) 0°C to 70°C Molded SSOP (R20) ML4877ER (OBSOLETE) –20ºC to 70ºC Molded SSOP (R20) is a registered trademark of Micro Linear Corporation. All other trademarks are the property of their respective owners. Products described herein may be covered by one or more of the following U.S. patents: 4,897,611; 4,964,026; 5,027,116; 5,281,862; 5,283,483; 5,418,502; 5,508,570; 5,510,727; 5,523,940; 5,546,017; 5,559,470; 5,565,761; 5,592,128; 5,594,376; 5,652,479; 5,661,427; 5,663,874; 5,672,959; 5,689,167; 5,714,897; 5,717,798; 5,742,151; 5,747,977; 5,754,012; 5,757,174; 5,767,653; 5,777,514; 5,793,168; 5,798,635; 5,804,950; 5,808,455; 5,811,999; 5,818,207; 5,818,669; 5,825,165; 5,825,223. Japan: 2,598,946; 2,619,299; 2,704,176; 2,821,714. Other patents are pending. Micro Linear reserves the right to make changes to any product herein to improve reliability, function or design. Micro Linear does not assume any liability arising out of the application or use of any product described herein, neither does it convey any license under its patent right nor the rights of others. The circuits contained in this data sheet are offered as possible applications only. Micro Linear makes no warranties or representations as to whether the illustrated circuits infringe any intellectual property rights of others, and will accept no responsibility or liability for use of any application herein. The customer is urged to consult with appropriate legal counsel before deciding on a particular application. 10/29/98 Printed in U.S.A. DS4877-01 2092 Concourse Drive San Jose, CA 95131 Tel: (408) 433-5200 Fax: (408) 432-0295 www.microlinear.com 11