6-Channel EMI Filter Array with ESD Protection

CM1440
6-Channel EMI Filter Array
with ESD Protection
Product Description
The CM1440 is a six channel low−pass EMI filter array with ESD
protection that reduces EMI/RFI emissions while providing robust
protection from ESD strikes. Each EMI filter channel integrates a high
quality pi−style filter (30 pF − 100 W − 30 pF) which provides greater
than 30 dB of attenuation in the 800 MHz to 2.7 GHz frequency range.
The parts include avalanche−type ESD diodes on every pin, which
provide a very high level of protection for sensitive electronic
components that may be subjected to electrostatic discharge (ESD).
The ESD protection diodes connected to the filter ports safely
dissipate ESD strikes of ±30 kV, beyond the maximum requirement of
the IEC61000−4−2 international standard. Using the MIL−STD−883
(Method 3015) specification for Human Body Model (HBM) ESD, the
pins are protected for contact discharges at greater than ±30 kV.
This device is particularly well−suited for portable electronics (e.g.
wireless handsets, PDAs, notebook computers) because of its small
package and easy−to−use pin assignments. In particular, the CM1440
is ideal for EMI filtering and protecting data and control lines for the
I/O data ports, LCD display and camera interface in mobile handsets.
The CM1440 incorporates OptiGuardt which results in improved
reliability at assembly. The CM1440 is available in a space saving, low
profile Chip Scale Package with RoHS−compliant lead−free finishing.
It is manufactured with a 0.40 mm pitch and 0.25 mm CSP solder ball
to provide up to 28% board space savings versus competing CSP
devices with 0.50 mm pitch and 0.30 mm CSP solder ball.
Features
• Six Channels of EMI Filtering for Data Ports
• Pi−Style EMI Filters in a Capacitor−Resistor−Capacitor (C−R−C)
•
•
•
•
•
•
•
Network
±30 kV ESD Protection on Each Channel
(IEC 61000−4−2 Level 4, Contact Discharge)
±30 kV ESD Protection on Each Channel (HBM)
Greater than 35 dB Attenuation (Typical) at 1 GHz
15−Bump, 0.4 mm pitch, 2.360 mm X 1.053 mm Footprint Chip
Scale Package (CSP)
Chip Scale Package Features Extremely Low Lead Inductance for
Optimum Filter and ESD Performance
OptiGuardt Coated for Improved Reliability at Assembly
These Devices are Pb−Free and are RoHS Compliant
Applications
• LCD and Camera Data Lines in Mobile Handsets
• I/O Port Protection for Mobile Handsets, Notebook
•
March, 2011 − Rev. 4
WLCSP15
CP SUFFIX
CASE 567BP
MARKING DIAGRAM
N406 MG
G
N406
= CM1440−06CP
M
= Date Code
G
= Pb−Free Package
(Note: Microdot may be in either location)
ORDERING INFORMATION
Device
Package
Shipping†
CM1440−06CP
CSP−15
(Pb−Free)
3500/Tape & Reel
†For information on tape and reel specifications,
including part orientation and tape sizes, please
refer to our Tape and Reel Packaging Specification
Brochure, BRD8011/D.
• Wireless Handsets
• Handheld PCs / PDAs
• LCD and Camera Modules
Computers, PDAs, etc.
EMI Filtering for Data Ports in Cell Phones, PDAs or
Notebook Computers
© Semiconductor Components Industries, LLC, 2011
http://onsemi.com
1
Publication Order Number:
CM1440/D
CM1440
BLOCK DIAGRAM
100 W
FILTERn*
(Pins A1−A6)
30 pF
FILTERn*
(Pins C1−C6)
30 pF
GND
(Pins B1−B3)
1 of 6 EMI/RFI + ESD Channels
*See Package/Pinout Diagrams for expanded pin information.
PACKAGE / PINOUT DIAGRAMS
Orientation
Marking
Table 1. PIN DESCRIPTIONS
15−bump CSP Package
Name
Description
A1
FILTER1
Filter Channel 1
A2
FILTER2
Filter Channel 2
A3
FILTER3
Filter Channel 3
A4
FILTER4
Filter Channel 4
A5
FILTER5
Filter Channel 5
A6
FILTER6
Filter Channel 6
B1−B3
GND
Device Ground
C1
FILTER1
Filter Channel 1
C2
FILTER2
Filter Channel 2
C3
FILTER3
Filter Channel 3
C4
FILTER4
Filter Channel 4
C5
FILTER5
Filter Channel 5
C6
FILTER6
Filter Channel 6
A
1
+
5
6
N406
B
C
Bottom View
(Bumps Up View)
FILTER1 FILTER2 FILTER3 FILTER4 FILTER5 FILTER6
C1
Orientation
Marking
Pin
Top View
(Bumps Down View)
2
3
4
C2
C3
C4
C5
C6
GND
GND
GND
B1
B2
B3
FILTER1 FILTER2 FILTER3 FILTER4 FILTER5 FILTER6
A1
A2
A3
A4
A5
A6
A1
CM1440−06CP
15 Bump CSP Package
SPECIFICATIONS
Table 2. ABSOLUTE MAXIMUM RATINGS
Parameter
Rating
Units
–65 to +150
°C
DC Power per Resistor
100
mW
DC Package Power Rating
500
mW
Storage Temperature Range
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
Table 3. STANDARD OPERATING CONDITIONS
Parameter
Operating Temperature Range
http://onsemi.com
2
Rating
Units
–40 to +85
°C
CM1440
Table 4. ELECTRICAL OPERATING CHARACTERISTICS (Note 1)
Symbol
R
CTOTAL
Parameter
Conditions
Resistance
Min
Typ
Max
Units
80
100
120
W
Total Channel Capacitance
At 2.5 VDC Reverse Bias,
1 MHz, 30 mVAC
48
60
72
pF
Capacitance
At 2.5 VDC Reverse Bias,
1 MHz, 30 mVAC
24
30
36
pF
Standoff Voltage
IDIODE = 10 mA
6.0
ILEAK
Diode Leakage Current (reverse bias)
VDIODE = 3.3 V
0.1
1.0
VSIG
Signal Voltage
Positive Clamp
Negative Clamp
ILOAD = 10 mA
6.8
–0.8
9.0
−0.4
VESD
In−system ESD Withstand Voltage
a) Human Body Model, MIL−STD−883,
Method 3015
b) Contact Discharge per IEC 61000−4−2
Level 4
(Note 2)
C
VDIODE
RDYN
fC
mA
V
kV
±30
±30
Dynamic Resistance
Positive
Negative
Cut−off Frequency
ZSOURCE = 50 W, ZLOAD = 50 W
5.6
−1.5
V
2.3
0.9
R = 100 W, C = 30 pF
1. TA = 25°C unless otherwise specified.
2. ESD applied to input and output pins with respect to GND, one at a time.
http://onsemi.com
3
60
W
MHz
CM1440
PERFORMANCE INFORMATION
Typical Filter Performance (TA = 255C, DC Bias = 0 V, 50 W Environment)
Figure 1. Insertion Loss vs. Frequency (A1−C1 to GND B1)
Figure 2. Insertion Loss vs. Frequency (A2−C2 to GND B1)
http://onsemi.com
4
CM1440
PERFORMANCE INFORMATION (Cont’d)
Typical Filter Performance (TA = 255C, DC Bias = 0 V, 50 W Environment)
Figure 3. Insertion Loss vs. Frequency (A3−C3 to GND B2)
Figure 4. Insertion Loss vs. Frequency (A4−C4 to GND B2)
http://onsemi.com
5
CM1440
PERFORMANCE INFORMATION (Cont’d)
Typical Filter Performance (TA = 255C, DC Bias = 0 V, 50 W Environment)
Figure 5. Insertion Loss vs. Frequency (A5−C5 to GND B3)
Figure 6. Insertion Loss vs. Frequency (A6−C6 to GND B3)
http://onsemi.com
6
CM1440
PERFORMANCE INFORMATION (Cont’d)
Typical Diode Capacitance vs. Input Voltage
Figure 7. Filter Capacitance vs. Input Voltage
(normalized to capacitance at 2.5 VDC and 255C)
http://onsemi.com
7
CM1440
APPLICATION INFORMATION
Table 5. PRINTED CIRCUIT BOARD RECOMMENDATIONS
Parameter
Value
Pad Size on PCB
0.240 mm
Pad Shape
Round
Pad Definition
Non−Solder Mask defined pads
Solder Mask Opening
0.290 mm Round
Solder Stencil Thickness
0.125 − 0.150 mm
Solder Stencil Aperture Opening (laser cut, 5% tapered walls)
0.300 mm Round
Solder Flux Ratio
50/50 by volume
Solder Paste Type
No Clean
Pad Protective Finish
OSP (Entek Cu Plus 106A)
Tolerance − Edge To Corner Ball
±50 mm
Solder Ball Side Coplanarity
±20 mm
Maximum Dwell Time Above Liquidous
60 seconds
Maximum Soldering Temperature for Lead−free Devices using a Lead−free Solder Paste
260°C
Non−Solder Mask Defined Pad
0.240 mm DIA.
Solder Stencil Opening
0.300 mm DIA.
Solder Mask Opening
0.290 mm DIA.
Figure 8. Recommended Non−Solder Mask Defined Pad Illustration
Temperature (5C)
250
200
150
100
50
0
1:00.0
2:00.0
3:00.0
Time (minutes)
4:00.0
Figure 9. Lead−free (SnAgCu) Solder Ball Reflow Profile
http://onsemi.com
8
CM1440
PACKAGE DIMENSIONS
WLCSP15, 2.36x1.05
CASE 567BP−01
ISSUE O
PIN A1
REFERENCE
2X
0.05 C
2X
D
È
È
0.05 C
A
E
DIM
A
A1
A2
b
D
E
eD
eE
TOP VIEW
ÉÉÉÉÉÉ
OptiGuard Option
0.05 C
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. COPLANARITY APPLIES TO SPHERICAL
CROWNS OF SOLDER BALLS.
B
A2
RECOMMENDED
SOLDERING FOOTPRINT*
A
0.05 C
NOTE 3
A1
SIDE VIEW
C
SEATING
PLANE
eD/2
15X
b
0.05 C A B
0.03 C
eD
MILLIMETERS
MIN
MAX
0.72
0.57
0.17
0.24
0.42 REF
0.24
0.29
2.36 BSC
1.05 BSC
0.400 BSC
0.347 BSC
PACKAGE
OUTLINE
A1
0.35
eE
0.35
15X
0.40
PITCH
C
B
0.25
DIMENSIONS: MILLIMETERS
A
1 2 3
4 5 6
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
7 8 9
BOTTOM VIEW
OptiGuardt is a trademark of Semiconductor Components Industries, LLC (SCILLC).
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
9
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
CM1440/D