M6000 series H6000 series VCXO 5.0V Full/Half size, Thru-hole, HCMOS/TTL Features RoHS Status Frequency range of 1KHz to 150MHz Industrial temperature range of -40 to +85ºC Excellent incremental and best-straight-line linearity Start-up time is less than 5ms Applications Phase locked loops xDSL customer premise equipment 3 MHz 55MHz to Cable modems ATM/SONET/SDH Electrical Specifications Parameter Symbol Frequency Range F Frequency Stability ∆F/F Aging Condition Min 0.001 Operating Temperature at 25°C 40 First Year After First Year 3 1 Operating Temperature T -40 Supply Voltage VCC 4.5 Supply Current ICC Output Levels Rise & Fall Times “0” Level, sinking 16mA “1” Level, sourcing 10mA From 0.4 to (VDD-.4) V (Above 35 MHz) Input Impedance Pin 5, VC Symmetry At VDD/2 Control Voltage Bandwidth Typ Max Unit 150 MHz 50 ppm ppm ppm/yr +85 C 5.0 5.5 V 30 45 mA 0.4 VDD-0.4 2.5 15 4 2 1000 150 V ns kOhm 45/55 15 Note % kHz 75 South Street, Hopkinton, MA 01748 • 800-982-5737 • 508-435-6831 • FAX 508-497-6377 • www.ctsvalpey.com • RevB0513 Specifications are subject to change without notice 1 M6000 series H6000 series VCXO 5.0V Full/Half size, Thru-hole, HCMOS/TTL Environmental and Mechanical Conditions Parameter Shock Vibration Humidity Gross Leak Fine Leak Pins Bend Test Conditions 1000 Gs, 0.35 ms, 1/2 sine wave, 3 shocks in each plane 10-2000 Hz of 0.06" d.a. or 20 Gs, whichever is less Resistant to 85° R.H. at 85°C Each unit checked in 125°C fluorocarbon Mass spectrometer leak rate less than 2 X 10-8 atm, cc/sec of helium Kovar, nickel plated with 60/40 solder coat Will withstand two bends of 90° from reference Header Steel, with nickel plated Case Stainless steel, type 304 Marking Resistance to Solvents Center frequency is between two voltages with ±50 ppm stability Permanent black epoxy ink or laser marked MIL STD 202, Method 215 DESCRIPTIONS M6001, H6001 M6002, H6002 M6003, H6003 M6004, H6004 M6005, H6005 M6006, H6006 Center frequency is at 2.5V with ±20 ppm stability M6007, H6007 M6021, H6021 M6022, H6022 M6023, H6023 ±175 ppm, min. deviation when using 0.3 to 10V control-voltage ±75 ppm, min. deviation when using 0.3 to 4.0V control-voltage ±175 ppm to ±300 ppm deviation when using 0.3 to 10V control-voltage ±125 ppm deviation when using 0.3 to 4.0V control-voltage ±75 ppm to ±300 ppm deviation when using 1.0 to 4.0 control-voltage, for use where the control voltage is 1 volt off both rails ±150 ppm, min. deviation when using 0 to 5.0 control-voltage ±125 ppm to ±250 ppm deviation when using 0.5 to 4.5 control-voltage ±75 ppm capture when using 0.5 to 4.5V control-voltage and 2.5V center with 50 ppm stability ±100 ppm capture when using 0.5 to 4.5V control-voltage and 2.5V center with 50 ppm stability ±150 ppm capture when using 0.5 to 4.5V control-voltage and 2.5V center with 50 ppm stability 75 South Street, Hopkinton, MA 01748 • 800-982-5737 • 508-435-6831 • FAX 508-497-6377 • www.ctsvalpey.com • RevB0513 Specifications are subject to change without notice 2 M6000 series H6000 series VCXO 5.0V Full/Half size, Thru-hole, HCMOS/TTL Pin # 1 Full size (M) Control Voltage 4 N/C 5 8 N/C Ground & Case Output 14 +5.0V, VDD 7 Half size (H) Control Voltage Ground & Case Output N/C +5.0V, VDD N/C HOW TO ORDER M - “M” is full size DIL “H” is half size DIL 6 0 0 1 “6001” is model type - FREQ. G Leave blank for straight leads Add “G” for gullwig 75 South Street, Hopkinton, MA 01748 • 800-982-5737 • 508-435-6831 • FAX 508-497-6377 • www.ctsvalpey.com • RevB0513 Specifications are subject to change without notice 3 M6000 series H6000 series VCXO 5.0V Full/Half size, Thru-hole, HCMOS/TTL Frequency Deviation, ppm FREQUENCY VS. CONTROL VOLTAGE FOR TYPICAL DEVICE 75 South Street, Hopkinton, MA 01748 • 800-982-5737 • 508-435-6831 • FAX 508-497-6377 • www.ctsvalpey.com • RevB0513 Specifications are subject to change without notice 4