NGTB75N60SWG IGBT - Inverter Welding This Insulated Gate Bipolar Transistor (IGBT) features a robust and cost effective Trench construction, and provides superior performance in demanding switching applications, offering both low on state voltage and minimal switching loss. The IGBT is well suited for welding applications. Incorporated into the device is a soft and fast co−packaged free wheeling diode with a low forward voltage. www.onsemi.com 75 A, 600 V VCEsat = 1.70 V EOFF = 1.0 mJ Features • • • • • TJmax = 175°C Soft Fast Reverse Recovery Diode Optimized for High Speed Switching 5 ms Short−Circuit Capability These are Pb−Free Devices C Typical Applications • Welding G ABSOLUTE MAXIMUM RATINGS Rating Symbol Value Unit Collector−emitter voltage VCES 600 V Collector current @ TC = 25°C @ TC = 100°C IC Diode Forward Current @ TC = 25°C @ TC = 100°C IF E A 100 75 A 100 75 C Diode Pulsed Current TPULSE Limited by TJ Max IFM 200 A Pulsed collector current, Tpulse limited by TJmax ICM 200 A Short−circuit withstand time VGE = 15 V, VCE = 400 V, TJ ≤ +150°C tSC 5 ms Gate−emitter voltage VGE $20 V V $30 Transient gate−emitter voltage (TPULSE = 5 ms, D < 0.10) G Power Dissipation @ TC = 25°C @ TC = 100°C PD Operating junction temperature range TJ −55 to +175 °C Storage temperature range Tstg −55 to +175 °C Lead temperature for soldering, 1/8” from case for 5 seconds TSLD 260 °C TO−247 CASE 340AL E MARKING DIAGRAM 75N60S AYWWG W 595 265 Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. A Y WW G ORDERING INFORMATION Device NGTB75N60SWG © Semiconductor Components Industries, LLC, 2014 December, 2014 − Rev. 1 1 = Assembly Location = Year = Work Week = Pb−Free Package Package Shipping TO−247 (Pb−Free) 30 Units / Rail Publication Order Number: NGTB75N60SW/D NGTB75N60SWG THERMAL CHARACTERISTICS Symbol Value Unit Thermal resistance junction−to−case, for IGBT Rating RqJC 0.28 °C/W Thermal resistance junction−to−case, for Diode RqJC 0.62 °C/W Thermal resistance junction−to−ambient RqJA 40 °C/W ELECTRICAL CHARACTERISTICS (TJ = 25°C unless otherwise specified) Parameter Test Conditions Symbol Min Typ Max Unit VGE = 0 V, IC = 500 mA V(BR)CES 600 − − V VGE = 15 V, IC = 75 A VGE = 15 V, IC = 75 A, TJ = 175°C VCEsat 1.50 − 1.70 1.85 2.00 − V STATIC CHARACTERISTIC Collector−emitter breakdown voltage, gate−emitter short−circuited Collector−emitter saturation voltage VGE = VCE, IC = 350 mA VGE(th) 4.5 5.5 6.5 V Collector−emitter cut−off current, gate− emitter short−circuited VGE = 0 V, VCE = 600 V VGE = 0 V, VCE = 600 V, TJ = 175°C ICES − − − − 0.1 4.0 mA Gate leakage current, collector−emitter short−circuited VGE = 20 V , VCE = 0 V IGES − − 200 nA Cies − 7500 − pF Coes − 300 − Cres − 190 − Qg − 310 − Qge − 60 − Qgc − 150 − td(on) − 110 − Gate−emitter threshold voltage DYNAMIC CHARACTERISTIC Input capacitance Output capacitance VCE = 20 V, VGE = 0 V, f = 1 MHz Reverse transfer capacitance Gate charge total Gate to emitter charge VCE = 480 V, IC = 75 A, VGE = 15 V Gate to collector charge nC SWITCHING CHARACTERISTIC, INDUCTIVE LOAD Turn−on delay time Rise time tr − 48 − td(off) − 270 − tf − 70 − Eon − 1.5 − Eoff − 1.0 − Total switching loss Ets − 2.5 − Turn−on delay time td(on) − 100 − tr − 50 − td(off) − 280 − tf − 100 − Eon − 1.9 − Turn−off switching loss Eoff − 1.8 − Total switching loss Ets − 3.7 − VF 1.70 − 2.20 2.40 2.90 − Turn−off delay time Fall time Turn−on switching loss TJ = 25°C VCC = 400 V, IC = 75 A Rg = 10 W VGE = 0 V/ 15 V Turn−off switching loss Rise time Turn−off delay time Fall time Turn−on switching loss TJ = 150°C VCC = 400 V, IC = 75 A Rg = 10 W VGE = 0 V/ 15 V ns mJ ns mJ DIODE CHARACTERISTIC Forward voltage Reverse recovery time Reverse recovery charge Reverse recovery current VGE = 0 V, IF = 75 A VGE = 0 V, IF = 50 A, TJ = 175°C TJ = 25°C IF = 75 A, VR = 200 V diF/dt = 200 A/ms V trr − 80 − ns Qrr − 0.40 − mC Irrm − 8 − A Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be indicated by the Electrical Characteristics if operated under different conditions. www.onsemi.com 2 NGTB75N60SWG TYPICAL CHARACTERISTICS 200 VGE = 20 V to 13 V 180 TJ = 25°C 160 140 11 V 120 100 10 V 80 60 40 9V 20 8V 7V 7 0 0 1 2 3 4 5 6 VGE = 20 V to 15 V 180 140 TJ = 150°C 120 11 V 100 10 V 80 60 9V 40 8V 7V 20 0 0 8 1 4 5 6 7 Figure 2. Output Characteristics IF, FORWARD CURRENT (A) Cies 1000 Coes 100 Cres 10 60 50 40 30 20 TJ = 150°C 10 TJ = 25°C 0 10 20 30 40 50 60 70 80 90 100 0 0.5 Figure 3. Typical Capacitance SWITCHING LOSS (mJ) 10 8 6 VCE = 400 V VGE = 15 V IC = 75 A 50 100 150 200 250 2.5 3.5 3.0 VCE = 400 V VGE = 15 V TJ = 150°C Rg = 10 W 5 12 0 2.0 4.0 6 14 2 1.5 Figure 4. Diode Forward Characteristics VCE = 400 V 4 1.0 VF, FORWARD VOLTAGE (V) VCE, COLLECTOR−EMITTER VOLTAGE (V) 16 8 70 1 VGE, GATE−EMITTER VOLTAGE (V) 3 Figure 1. Output Characteristics 10,000 0 2 VCE, COLLECTOR−EMITTER VOLTAGE (V) TJ = 25°C 0 13 V 160 VCE, COLLECTOR−EMITTER VOLTAGE (V) 100,000 C, CAPACITANCE (pF) IC, COLLECTOR CURRENT (A) IC, COLLECTOR CURRENT (A) 200 300 Eon 4 3 Eoff 2 1 0 350 15 25 35 45 55 65 75 85 QG, GATE CHARGE (nC) IC, COLLECTOR CURRENT (A) Figure 5. Typical Gate Charge Figure 6. Switching Loss vs. IC www.onsemi.com 3 95 105 NGTB75N60SWG TYPICAL CHARACTERISTICS 1000 IC, COLLECTOR CURRENT (A) SWITCHING TIME (ns) 1000 td(off) tf 100 td(on) tr 10 VCE = 400 V VGE = 15 V TJ = 150°C Rg = 10 W 50 ms 100 1 ms 1 Single Nonrepetitive Pulse TC = 25°C Curves must be derated linearly with increase in temperature 0.1 0.01 15 25 35 45 55 65 75 85 95 100 ms dc operation 10 105 1 IC, COLLECTOR CURRENT (A) 10 100 1000 VCE, COLLECTOR−EMITTER VOLTAGE (V) Figure 7. Switching Time vs. IC Figure 8. Safe Operating Area SQUARE−WAVE PEAK R(t) (°C/W) 1 RqJC = 0.282 50% Duty Cycle 0.1 20% 10% 5% 0.01 2% R1 Junction R2 C1 0.001 0.000001 Case Cn C2 Ri (°C/W) Ci (J/°C) 0.026955 0.024252 0.022476 0.055395 0.112157 0.040934 0.003710 0.013039 0.044492 0.057085 0.089161 0.772537 Duty Factor = t1/t2 Peak TJ = PDM x ZqJC + TC Single Pulse 0.0001 Rn 0.00001 0.001 0.0001 0.01 0.1 1 ON−PULSE WIDTH (s) Figure 9. IGBT Transient Thermal Impedance SQUARE−WAVE PEAK R(t) (°C/W) 1 RqJC = 0.622 50% Duty Cycle 20% 0.1 10% 5% Junction R1 R2 Rn C1 C2 Cn 2% 0.01 Single Pulse Duty Factor = t1/t2 Peak TJ = PDM x ZqJC + TC 0.001 0.000001 0.00001 0.0001 0.001 0.01 ON−PULSE WIDTH (s) Figure 10. Diode Transient Thermal Impedance www.onsemi.com 4 Case Ri (°C/W) Ci (J/°C) 0.007983 0.010584 0.011330 0.026752 0.047379 0.103276 0.061288 0.065591 0.134666 0.152791 0.000125 0.000945 0.002791 0.003738 0.006674 0.009683 0.051597 0.152460 0.234823 0.654488 0.1 1 NGTB75N60SWG PACKAGE DIMENSIONS TO−247 CASE 340AL ISSUE A B A NOTE 4 E SEATING PLANE 0.635 M P A Q E2 D S NOTE 3 1 2 4 DIM A A1 b b2 b4 c D E E2 e L L1 P Q S 3 L1 NOTE 5 L 2X b2 c b4 3X e A1 b 0.25 NOTE 7 M B A M NOTE 6 E2/2 NOTE 4 B A NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. SLOT REQUIRED, NOTCH MAY BE ROUNDED. 4. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.13 PER SIDE. THESE DIMENSIONS ARE MEASURED AT THE OUTERMOST EXTREME OF THE PLASTIC BODY. 5. LEAD FINISH IS UNCONTROLLED IN THE REGION DEFINED BY L1. 6. ∅P SHALL HAVE A MAXIMUM DRAFT ANGLE OF 1.5° TO THE TOP OF THE PART WITH A MAXIMUM DIAMETER OF 3.91. 7. DIMENSION A1 TO BE MEASURED IN THE REGION DEFINED BY L1. M MILLIMETERS MIN MAX 4.70 5.30 2.20 2.60 1.00 1.40 1.65 2.35 2.60 3.40 0.40 0.80 20.30 21.40 15.50 16.25 4.32 5.49 5.45 BSC 19.80 20.80 3.50 4.50 3.55 3.65 5.40 6.20 6.15 BSC ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5817−1050 www.onsemi.com 5 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NGTB75N60SW/D