AD712-DSCC: Military Data Sheet

REVISIONS
LTR
DESCRIPTION
A
Update document paragraphs to current
requirements. - ro
DATE
APPROVED
16-02-08
C. SAFFLE
Prepared in accordance with ASME Y14.24
Vendor item drawing
REV
PAGE
REV
PAGE
REV STATUS
OF PAGES
REV
A
A
A
A
A
A
A
A
A
A
A
PAGE
1
2
3
4
5
6
7
8
9
10
11
PMIC N/A
PREPARED BY
RICK OFFICER
Original date of drawing
YY-MM-DD
CHECKED BY
RAJESH PITHADIA
10-12-13
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
http://www.landandmaritime.dla.mil/
TITLE
SIZE
CODE IDENT. NO.
A
REV
AMSC N/A
MICROCIRCUIT, LINEAR, DUAL, HIGH SPEED
BiFET OPERATIONAL AMPLIFIER, MONOLITHIC
SILICON
APPROVED BY
CHARLES F. SAFFLE
DWG NO.
V62/11603
16236
A
PAGE
1
OF
11
5962-V036-16
1. SCOPE
1.1 Scope. This drawing documents the general requirements of a high performance dual, high speed bipolar field effect transistor
(BiFET) operational amplifier microcircuit, with an operating temperature range of -55C to +125C.
1.2 Vendor Item Drawing Administrative Control Number. The manufacturer’s PIN is the item of identification. The vendor item
drawing establishes an administrative control number for identifying the item on the engineering documentation:
V62/11603
-
Drawing
number
01
X
E
Device type
(See 1.2.1)
Case outline
(See 1.2.2)
Lead finish
(See 1.2.3)
1.2.1 Device type(s).
Device type
Generic
01
AD712-EP
Circuit function
Dual, high speed BiFET operational amplifier
1.2.2 Case outline(s). The case outline(s) are as specified herein.
Outline letter
Number of pins
X
8
JEDEC PUB 95
Package style
MS-012-AA
Plastic small outline
1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacturer:
Finish designator
A
B
C
D
E
Z
DLA LAND AND MARITIME
COLUMBUS, OHIO
Material
Hot solder dip
Tin-lead plate
Gold plate
Palladium
Gold flash palladium
Other
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/11603
PAGE
2
1.3 Absolute maximum ratings.
1/
Supply voltage (VS) ................................................................................................................ 18 V
Input voltage (VIN) .................................................................................................................... 18 V 2/
Output short circuit duration ..................................................................................................... Indefinite
Differential input voltage ........................................................................................................... +VS and -VS
Power dissipation(PD) .............................................................................................................. 14.4 mW
Junction temperature range (TJ) .............................................................................................. -65C to +150C
Storage temperature range (TSTG) .......................................................................................... -65C to +125C
Lead temperature range (soldering, 60 seconds) ..................................................................... +300C
Thermal resistance, junction to ambient (JC) .......................................................................... 43C/W
Thermal resistance, junction to ambient (JA) .......................................................................... 100C/W
1.4 Recommended operating conditions. 3/
Supply voltage (VS) ................................................................................................................ 15 V
Operating temperature range (TA) ........................................................................................... -55C to +125C
1/
2/
3/
Stresses beyond those listed under “absolute maximum rating” may cause permanent damage to the device. These are stress
ratings only, and functional operation of the device at these or any other conditions beyond those indicated under
“recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may
affect device reliability.
For supply voltages less than 18 V, the absolute maximum voltage is equal to the supply voltage.
Use of this product beyond the manufacturers design rules or stated parameters is done at the user’s risk. The manufacturer
and/or distributor maintain no responsibility or liability for product used beyond the stated limits.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/11603
PAGE
3
2. APPLICABLE DOCUMENTS
JEDEC Solid State Technology Association
JEDEC PUB 95
–
Registered and Standard Outlines for Semiconductor Devices
(Copies of these documents are available online at http:/www.jedec.org or from JEDEC – Solid State Technology Association,
3103 North 10th Street, Suite 240–S, Arlington, VA 22201-2107).
3. REQUIREMENTS
3.1 Marking. Parts shall be permanently and legibly marked with the manufacturer’s part number as shown in 6.3 herein and as
follows:
A.
B.
C.
Manufacturer’s name, CAGE code, or logo
Pin 1 identifier
ESDS identification (optional)
3.2 Unit container. The unit container shall be marked with the manufacturer’s part number and with items A and C (if applicable)
above.
3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are
as specified in 1.3, 1.4, and table I herein.
3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified herein.
3.5 Diagrams.
3.5.1 Case outline. The case outline shall be as shown in 1.2.2 and figure 1.
3.5.2 Terminal connections. The terminal connections shall be as shown in figure 2.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/11603
PAGE
4
TABLE I. Electrical performance characteristics. 1/
Test
Symbol
Conditions
VS = 15 V
unless otherwise specified
Temperature,
TA
Device
type
Limits
Min
Unit
Max
Input offset voltage section 2/
Initial offset voltage
01
+25C
VIO
3
4
-55C to +125C
Initial offset voltage
versus temperature
VIO / T
+25C
01
Initial offset voltage
versus supply
VIO /
+25C
01
Long term offset
stability
Input bias current 3/
Input offset current
IIB
IIO
20
V/C
76
dB
76
-55C to +125C
VS
mV
+25C
01
+25C
01
15 typical
V/
month
75
pA
+125C
77
nA
VCM = 10 V
+25C
100
pA
VCM = 0 V
+25C
25
pA
26
nA
3
mV
VCM = 0 V
01
+125C
Matching characteristics section
Input offset voltage
01
+25C
VIO
4
-55C to +125C
Input offset voltage drift
Input bias current
IIB
Crosstalk
At f = 1 kHz
+25C
01
20
V/C
+25C
01
25
pA
+25C
01
At f = 100 kHz
120 typical
dB
90 typical
See footnotes at end of table.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/11603
PAGE
5
TABLE I. Electrical performance characteristics – Continued. 1/
Test
Symbol
Conditions
VS = 15 V
unless otherwise specified
Temperature,
TA
Device
type
Limits
Min
Unit
Max
Frequency response section
Small signal bandwidth
SSBW
+25C
01
3.0
MHz
Full power response
FPR
+25C
01
Slew rate
SR
+25C
01
Settling time to 0.01%
tS
+25C
01
1.2
s
Total harmonic
distortion
THD
+25C
01
0.0003 typical
%
12
||pF
200 typical
kHz
16
V/s
Input impedance section
Differential input
impedance
4/
+25C
01
3 x 10 || 5.5
typical
Common mode input
impedance
4/
+25C
01
3 x 10 || 5.5
typical
12
||pF
VDIN
+25C
01
20 typical
V
VCM
+25C
01
+14.5, -11.5
typical
V
Input voltage range section
Differential input
voltage range
Common mode
voltage
5/
6/
-55C to +125C
Common mode
rejection ratio
CMRR
VCM = 10 V
-VS
+4
01
+25C
76
-55C to +125C
76
+25C
70
-55C to +125C
70
VCM = 11 V
+VS
-2
dB
Input voltage noise section
Input voltage noise
2 typical
Vp-p
f = 10 Hz
45 typical
nV / Hz
f = 100 Hz
22 typical
f = 1 kHz
18 typical
f = 10 kHz
16 typical
0.1 Hz to 10 Hz
01
+25C
See footnotes at end of table.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/11603
PAGE
6
TABLE I. Electrical performance characteristics – Continued. 1/
Test
Symbol
Input current noise
NI
Open loop gain
AOL
Conditions
VS = 15 V
unless otherwise specified
Temperature,
TA
Device
type
Limits
Min
f = 1 kHz
+25C
01
+25C
01
Unit
Max
0.01 typical
150
pA / Hz
V/mV
100
-55C to +125C
Output characteristics
Output voltage swing
high
+25C
VOH
01
13.0
12.0
-55C to +125C
Output voltage swing
low
+25C
VOL
V
01
-12.5
V
-12.0
-55C to +125C
+25C
01
25 typical
mA
Rated performance
+25C
01
15 typical
V
Operating range
+25C
01
Quiescent current
+25C
01
Output current
IOUT
Power supply section
4.5
18
V
6.8
mA
1/
Testing and other quality control techniques are used to the extent deemed necessary to assure product performance over
the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters
may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization
and/or design.
2/
Input offset voltage specifications are guaranteed after 5 minutes of operation at TA = +25C.
3/
Bias current specifications are guaranteed maximum at either input after five minutes of operation at TA = +25C.
For higher temperatures, the current doubles every 10C.
4/
The || symbolizes that the input impedance is being represented as the resistance value is in parallel with the capacitance.
5/
Defined as voltage between inputs, such that neither exceeds 10 V from ground.
6/
Typically exceeding -14.1 V negative common mode voltage on either input results in an output phase reversal.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/11603
PAGE
7
Case X
FIGURE 1. Case outline.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/11603
PAGE
8
Case X
Dimensions
Inches
Symbol
Millimeters
Min
Max
Min
Max
A
0.0532
0.0688
1.35
1.75
A1
0.0040
0.0098
0.10
0.25
b
0.0122
0.0201
0.31
0.51
c
0.0067
0.0098
0.17
0.25
D
0.1890
0.1968
4.80
5.00
E
0.1497
0.1574
3.80
4.00
E1
0.2284
0.2441
5.80
6.20
e
0.0500 BSC
L
0.0157
n
1.27 BSC
0.0500
0.40
8
1.27
8
NOTES:
1. Controlling dimensions are millimeter, inch dimensions are given for reference only and are not appropriate
for use in design.
2. Body dimensions do not include mold flash or protrusion not to exceed 0.006 inch (0.15 mm).
3. Falls with JEDEC MS-012-AA.
FIGURE 1. Case outline – Continued.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/11603
PAGE
9
Device type
01
Case outline
X
Terminal number
Terminal symbol
1
OUTPUT 1
2
INVERTING INPUT 1
3
NONINVERTING INPUT 1
4
-VS
5
NONINVERTING INPUT 2
6
INVERTING INPUT 2
7
OUTPUT 2
8
+VS
FIGURE 2. Terminal connections.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/11603
PAGE
10
4. VERIFICATION
4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as
indicated in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices,
classification, packaging, and labeling of moisture sensitive devices, as applicable.
5. PREPARATION FOR DELIVERY
5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturer’s standard commercial
practices for electrostatic discharge sensitive devices.
6. NOTES
6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum.
6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturer’s data book.
The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided.
6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee
of present or continued availability as a source of supply for the item. DLA Land and Maritime maintains an online database of all
current sources of supply at http://www.landandmaritime.dla.mil/Programs/Smcr/.
Vendor item drawing
administrative control
number 1/
Device
manufacturer
CAGE code
Vendor part number
V62/11603-01XE
24355
AD712TRZ-EP-R7
1/ The vendor item drawing establishes an administrative control number
for identifying the item on the engineering documentation.
CAGE code
24355
DLA LAND AND MARITIME
COLUMBUS, OHIO
Source of supply
Analog Devices
Route 1 Industrial Park
P.O. Box 9106
Norwood, MA 02062
Point of contact: Raheen Business Park
Limerick, Ireland
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/11603
PAGE
11