OP284-DSCC: Military Data Sheet

REVISIONS
LTR
DESCRIPTION
DATE
Prepared in accordance with ASME Y14.24
APPROVED
Vendor item drawing
REV
PAGE
REV
PAGE
REV STATUS
OF PAGES
REV
PAGE
1
2
PMIC N/A
PREPARED BY
RICK OFFICER
Original date of drawing
YY-MM-DD
CHECKED BY
RAJESH PITHADIA
15-02-19
4
A
REV
5
6
7
8
9
10
11
12
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
http://www.landandmaritime.dla.mil/
TITLE
MICROCIRCUIT, LINEAR, PRECISION, RAIL TO
RAIL INPUT AND OUTPUT DUAL OPERATIONAL
AMPLIFIER, MONOLITHIC SILICON
APPROVED BY
CHARLES F. SAFFLE
SIZE
AMSC N/A
3
CODE IDENT. NO.
DWG NO.
V62/14624
16236
PAGE
1
OF
12
5962-V045-15
1. SCOPE
1.1 Scope. This drawing documents the general requirements of a high performance precision rail to rail input and output (RRIO)
dual operational amplifier microcircuit, with an operating temperature range of -55C to +125C.
1.2 Vendor Item Drawing Administrative Control Number. The manufacturer’s PIN is the item of identification. The vendor item
drawing establishes an administrative control number for identifying the item on the engineering documentation:
V62/14624
-
Drawing
number
01
X
E
Device type
(See 1.2.1)
Case outline
(See 1.2.2)
Lead finish
(See 1.2.3)
1.2.1 Device type(s).
Device type
Generic
01
OP284-EP
Circuit function
Precision rail to rail input and output (RRIO)
dual operational amplifier
1.2.2 Case outline(s). The case outline(s) are as specified herein.
Outline letter
Number of pins
X
8
JEDEC PUB 95
Package style
MS-001
Plastic dual in line
1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacturer:
Finish designator
A
B
C
D
E
Z
DLA LAND AND MARITIME
COLUMBUS, OHIO
Material
Hot solder dip
Tin-lead plate
Gold plate
Palladium
Gold flash palladium
Other
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/14624
PAGE
2
1.3 Absolute maximum ratings.
1/
Supply voltage range (VS) .......................................................................................... 18 V
Input voltage (VIN) ......................................................................................................
Differential input voltage .............................................................................................
Output short circuit duration to GND ..........................................................................
Storage temperature range (TSTG) ............................................................................
18 V
0.6 V 2/
Indefinite
-65C to +150C
Junction temperature range (TJ) ................................................................................ -65C to +150C
Lead temperature (soldering, 60 seconds) ................................................................. 300C
Power dissipation (PD) ............................................................................................... 45 mW
Thermal resistance, junction to ambient (JC) ............................................................ 43C/W
Thermal resistance, junction to ambient (JA) ............................................................ 158C/W
1.4 Recommended operating conditions. 3/
Supply voltage range (VS) .......................................................................................... +5.0 V to 15 V
Operating temperature range (TA) ............................................................................. -55C to +125C
1/
2/
3/
Stresses beyond those listed under “absolute maximum rating” may cause permanent damage to the device. These are stress
ratings only, and functional operation of the device at these or any other conditions beyond those indicated under
“recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may
affect device reliability.
For input voltages greater than 0.6 V, the input current should be, limited to less than 5 mA to prevent degradation or destruction
of the input devices.
Use of this product beyond the manufacturers design rules or stated parameters is done at the user’s risk. The manufacturer
and/or distributor maintain no responsibility or liability for product used beyond the stated limits.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/14624
PAGE
3
2. APPLICABLE DOCUMENTS
JEDEC Solid State Technology Association
JEDEC PUB 95 –
Registered and Standard Outlines for Semiconductor Devices
(Copies of these documents are available online at http:/www.jedec.org or from JEDEC – Solid State Technology Association,
3103 North 10th Street, Suite 240–S, Arlington, VA 22201-2107).
3. REQUIREMENTS
3.1 Marking. Parts shall be permanently and legibly marked with the manufacturer’s part number as shown in 6.3 herein and as
follows:
A.
B.
C.
Manufacturer’s name, CAGE code, or logo
Pin 1 identifier
ESDS identification (optional)
3.2 Unit container. The unit container shall be marked with the manufacturer’s part number and with items A and C (if applicable)
above.
3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are
as specified in 1.3, 1.4, and table I herein.
3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified herein.
3.5 Diagrams.
3.5.1 Case outline. The case outline shall be as shown in 1.2.2 and figure 1.
3.5.2 Terminal connections. The terminal connections shall be as shown in figure 2.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/14624
PAGE
4
TABLE I. Electrical performance characteristics. 1/
Test
Symbol
Conditions
VS = 5.0 V, VCM = 2.5 V
unless otherwise specified
Temperature,
TA
Device
type
Limits
Min
Unit
Max
Input characteristics.
Offset voltage
25C
VOS
01
600
-55C to +125C
Input bias current
25C
IB
01
450
60 typical
25C
IOS
Input voltage range
VINR
Common mode
rejection ratio
CMRR
VCM = 0 V to 5 V
Large signal voltage
gain
AVO
-55C to +125C
01
25C
01
0
25C
01
60
1 V  VO  4 V, RL = 2 k
25C
01
5
V
dB
50
V/mV
240 typical
25C
IB / T
nA
25
-55C to +125C
Bias current drift
100
86
-55C to +125C
VCM = 1.0 V to 4.0 V
nA
700
-55C to +125C
Input offset current
V
100
25C
01
150 typical
pA/C
Output characteristics.
Output voltage high
VOH
IL = 1.0 mA
25C
01
Output voltage low
VOL
IL = 1.0 mA
25C
01
Output current
IOUT
25C
01
-55C to +125C
01
25C
01
4.80
V
125
mV
6.5
mA
Power supply.
Supply current/amplifier
ISY
Supply voltage
VS
VO = 2.5 V
3
1.45
mA
36
V
See footnote at end of table.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/14624
PAGE
5
TABLE I. Electrical performance characteristics – Continued. 1/
Test
Symbol
Conditions
VS = 5.0 V, VCM = 2.5 V
unless otherwise specified
Temperature,
TA
Device
type
Limits
Min
Unit
Max
Dynamic performance
Slew rate
SR
25C
RL = 2 k
01
1.65
V/s
2.4 typical
25C
01
2.5 typical
s
GBP
25C
01
3.25 typical
MHz
M
25C
01
45 typical
Degrees
Settling time
tS
Gain bandwidth
product
Phase margin
To 0.01%, 1.0 V step
Noise performance
Voltage noise
en p-p
0.1 Hz to 10 Hz
25C
01
0.3 typical
V p-p
Voltage noise density
en
f = 1 kHz
25C
01
3.9 typical
nV/ Hz
Current noise density
in
25C
01
0.4 typical
pA/ Hz
See footnote at end of table.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/14624
PAGE
6
TABLE I. Electrical performance characteristics – Continued. 1/
Test
Symbol
Conditions
VS = 15.0 V, VCM = 0 V
unless otherwise specified
Temperature,
TA
Device
type
Limits
Min
Unit
Max
Input characteristics.
Offset voltage
25C
VOS
01
550
-55C to +125C
Input bias current
25C
IB
01
450
80 typical
25C
IOS
Input voltage range
VINR
Common mode
rejection ratio
CMRR
VCM = -14.0 V to +14.0 V
-55C to +125C
01
25C
01
-15
-55C to +125C
01
86
AVO
-10 V  VO  10 V, RL = 2 k
25C
01
+15
V
dB
150
V/mV
1000 typical
25C
IB / T
nA
75
-55C to +125C
Bias current drift
100
90
25C
Large signal voltage
gain
nA
700
-55C to +125C
Input offset current
V
125
25C
01
150 typical
pA/C
Output characteristics.
Output voltage high
VOH
IL = 1.0 mA
25C
01
Output voltage low
VOL
IL = 1.0 mA
25C
01
Output current
IOUT
25C
01
10
mA
90
dB
14.8
V
-14.875
mV
Power supply.
Power supply rejection
ratio
PSRR
VS = 2.0 V to 18 V
-55C to +125C
01
Supply current/amplifier
ISY
VO = 0 V
-55C to +125C
01
2.0
mA
Supply current/amplifier
ISY
VS = 18 V
-55C to +125C
01
2.25
mA
See footnote at end of table.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/14624
PAGE
7
TABLE I. Electrical performance characteristics – Continued. 1/
Test
Symbol
Conditions
VS = 15.0 V, VCM = 0 V
unless otherwise specified
Temperature,
TA
Device
type
Limits
Min
Unit
Max
Dynamic performance.
Slew rate
SR
25C
RL = 2 k
01
2.4
V/s
4.0 typical
Full power bandwidth
BWP
1% distortion, RL = 2 k,
25C
01
35 typical
kHz
25C
01
4 typical
s
VO = 29 Vp-p
To 0.01%, 1.0 V step
Settling time
tS
Gain bandwidth
product
GBP
25C
01
4.25 typical
MHz
Phase margin
M
25C
01
50 typical
Degrees
Noise performance.
Voltage noise
en p-p
0.1 Hz to 10 Hz
25C
01
0.3 typical
V p-p
Voltage noise density
en
f = 1 kHz
25C
01
3.9 typical
nV/ Hz
Current noise density
in
25C
01
0.4 typical
pA/ Hz
1/
Testing and other quality control techniques are used to the extent deemed necessary to assure product performance over
the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters
may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization
and/or design.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/14624
PAGE
8
Case X
FIGURE 1. Case outline.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/14624
PAGE
9
Case X – continued.
Dimensions
Inches
Symbol
Millimeters
Minimum
Medium
Maximum
Minimum
Medium
Maximum
A
---
---
0.210
---
---
5.33
A1
0.015
---
---
0.38
---
---
b
0.014
0.018
0.022
0.36
0.46
0.56
c
0.008
0.010
0.014
0.20
0.25
0.36
D
0.355
0.365
0.400
9.02
9.27
10.16
E
0.240
0.250
0.280
6.10
6.35
7.11
E1
0.300
0.310
0.325
7.62
7.87
8.26
E2
---
---
0.430
---
---
10.92
e
L
0.100 BSC
0.115
0.130
2.54 BSC
0.150
2.92
3.30
3.81
NOTES:
1. Controlling dimensions are inch, millimeter dimensions are rounded off inch equivalents for reference only and
are not appropriate for use in design.
2. Corner leads may be configured as whole or half leads.
3. Falls within reference to JEDEC MS-001.
FIGURE 1. Case outline - Continued.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/14624
PAGE
10
Device type
01
Case outline
X
Terminal number
Terminal symbol
1
OUTPUT A
2
-INPUT A
3
+INPUT A
4
-VS
5
+INPUT B
6
-INPUT B
7
OUTPUT B
8
+VS
FIGURE 2. Terminal connections.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/14624
PAGE
11
4. VERIFICATION
4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as
indicated in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices,
classification, packaging, and labeling of moisture sensitive devices, as applicable.
5. PREPARATION FOR DELIVERY
5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturer’s standard commercial
practices for electrostatic discharge sensitive devices.
6. NOTES
6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum.
6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturer’s data book.
The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided.
6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee
of present or continued availability as a source of supply for the item. DLA Land and Maritime maintains an online database of all
current sources of supply at http://www.landandmaritime.dla.mil/Programs/Smcr/.
Vendor item drawing
administrative control
number 1/
Device
manufacturer
CAGE code
Vendor part number
V62/14624-01XE
24355
OP284TRZ-EP-R7
1/ The vendor item drawing establishes an administrative control number
for identifying the item on the engineering documentation.
CAGE code
24355
DLA LAND AND MARITIME
COLUMBUS, OHIO
Source of supply
Analog Devices
Route 1 Industrial Park
P.O. Box 9106
Norwood, MA 02062
Point of contact: Raheen Business Park
Limerick, Ireland
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/14624
PAGE
12