Semiconductor Qualification Test Report: GaAs HBT-E (QTR: 2013-00271)

Analog Devices Welcomes
Hittite Microwave Corporation
NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
www.analog.com
www.hittite.com
Report Title:
Qualification Test Report
Report Type:
See Attached
Date:
See Attached
QTR: 2013- 00271
Wafer Process: GaAs HBT-E
HMC740
HMC741
HMC754
HMC789
Rev: 03
QTR: 2013- 00271
Wafer Process: GaAs HBT-E
Rev: 03
Introduction
The testing performed for this report is designed to accelerate the predominant failure mode, electro-migration
(EM), for the devices under test. The devices are stressed at high temperature and DC biased to simulate a lifetime
of use at typical operating temperatures. Using the Arrhenius equation, the acceleration factor (AF) is calculated for
the stress testing based on the stress temperature and the typical use operating temperature.
This report is intended to summarize all of the High Temperature Operating Life Test (HTOL) data for the GaAs
HBT-E process. The FIT/MTTF data contained in this report includes all the stress testing performed on this
process to date and will be updated periodically as additional data becomes available. Data sheets for the tested
devices can be found at www.hittite.com.
Glossary of Terms & Definitions:
1. HTOL: High Temperature Operating Life. This test is used to determine the effects of bias conditions and
temperature on semiconductor devices over time. It simulates the devices’ operating condition in an accelerated
way, through high temperature and/or bias voltage, and is primarily for device qualification and reliability
monitoring. This test was performed in accordance with JEDEC JESD22-A108.
2. Operating Junction Temp (Toj): Temperature of the die active circuitry during typical operation.
3. Stress Junction Temp (Tsj): Temperature of the die active circuitry during stress testing.
QTR: 2013- 00271
Wafer Process: GaAs HBT-E
Rev: 03
Qualification Sample Selection:
All qualification devices used were manufactured and tested on standard production processes and met pre-stress
acceptance test requirements.
Summary of Qualification Tests:
HMC789 (QTR10004)
QTY
IN
77
QTY
OUT
77
HTOL, 1000 hours
77
77
Complete
Post HTOL Electrical Test
77
77
Pass
Bond Pull
10
10
Pass
Die Shear
10
10
Pass
SEM Inspection
5
5
Pass
Metal and Dielectric Thickness
5
5
Pass
QTY
IN
81
QTY
OUT
81
HTOL, 1000 hours
81
81
Complete
Post HTOL Electrical Test
81
81
Pass
TEST
Initial Electrical
PASS/FAIL
NOTES
Complete
30 wires from 10
devices.
HMC2172 (QTR2013-00339)
TEST
Initial Electrical
PASS/FAIL
Complete
NOTES
QTR: 2013- 00271
Wafer Process: GaAs HBT-E
Rev: 03
GaAs HBT-E Failure Rate Estimate
Based on the HTOL test results, a failure rate estimation was determined using the following
parameters:
With Device case temp, Tc = 85°C
HMC789 (QTR10004)
Operating Junction Temp (Toj) = 143°C (416°K)
Stress Junction Temp (Tsj) = 183°C (456°K)
HMC2171 (QTR2013-00339)
Operating Junction Temp (Toj) = 124°C (397°K)
Stress Junction Temp (Tsj) = 152°C (425°K)
Device hours:
HMC789 (QTR10004) = (77 X 1000hrs) = 77,000 hours
HMC2171 (QTR2013-00339) = (81 X 1000hrs) = 81,000 hours
For GaAs HBT-E MMIC, Activation Energy = 1.5 eV
Acceleration Factor (AF):
HMC789 (QTR10004) Acceleration Factor = exp[1.5/8.6 e-5(1/416-1/456)] = 39.6
HMC2171 (QTR2013-00339) Acceleration Factor = exp[1.5/8.6 e-5(1/397-1/425)] = 18.1
Equivalent hours = Device hours x Acceleration Factor
Equivalent hours = (77,000x39.6)+(81,000x18.1) = 4.51x106 hours
QTR: 2013- 00271
Wafer Process: GaAs HBT-E
Rev: 03
Since there was no failures and we used a time terminated test, F=0, and R = 2F+2 = 2
The failure rate was calculated using Chi Square Statistic:
at 60% and 90% Confidence Level (CL), with 0 units out of spec
and a 85°C device case temp;
Failure Rate
λ60 = [(χ2)60,2]/(2X 4.51x106 )] = 1.8/ 9.02x106 = 2.03x10-7 failures/hour or 202
FIT or MTTF = 4.93x106 Hours
λ90 = [(χ2)90,2]/(2X 4.51x106 )] = 4.6/ 9.02x106 = 5.11x10-7 failures/hour or 511
FIT or MTTF = 1.96x106 Hours