PDF Data Sheet

Analog Devices Welcomes
Hittite Microwave Corporation
NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
www.analog.com
www.hittite.com
THIS PAGE INTENTIONALLY LEFT BLANK
HMC369LP3 / 369LP3E
v04.0210
SMT GaAs HBT MMIC x2 ACTIVE
FREQUENCY MULTIPLIER, 9.9 - 12.7 GHz OUTPUT
FREQ. MULTIPLIERS - ACTIVE - SMT
4
Typical Applications
Features
Active Multiplier for X Band Applications:
Output Power: +4 dBm
• OC-192 Clock Recovery
Sub-Harmonic Suppression: 30 dBc
• Microwave Radio & VSAT
SSB Phase Noise: -142 dBc/Hz
• Military Radios, Radar & ECM
Single Supply: 5V@ 46 mA
• Test Instrumentation
16 Lead 3x3mm SMT Package: 9mm2
Functional Diagram
General Description
The HMC369LP3 & HMC369LP3E are active miniature
x2 frequency multipliers utilizing InGaP GaAs HBT
technology in 3x3 mm leadless QFN surface mount
packages. Power output is +4 dBm typical from a
single +5V supply and varies little vs. input power,
temperature and supply voltage. Suppression of
undesired fundamental and sub-harmonics is 30
dBc typical with respect to output signal level. The
low additive SSB phase noise of -142 dBc/Hz at
100 kHz offset helps the user maintain good system
noise performance. The HMC369LP3(E) is ideal for
use in LO multiplier chains allowing reduced parts
count versus traditional approaches. The HMC369LP3(E) are also useful for OC-192 clock recovery.
The application of 10 GBPS data to the input generates a -7 dBm clock tone at the output with spurious
signals suppressed by 25 dB.
Electrical Specifi cations, TA = +25° C, Vcc= 5V
Parameter
Min.
Frequency Range, Input
Frequency Range, Output
Max.
Min.
-5
Output Power
-1
Typ.
Max.
5.3 - 6.35
9.9 - 10.6
Input Power Range
GHz
10.6 - 12.7
+5
3
-5
0
Units
GHz
+5
dBm
4
dBm
Sub-Harmonic Suppression
30
30
dBc
Input Return Loss
17
16
dB
Output Return Loss
5.5
6
dB
-142
-142
dBc/Hz
SSB Phase Noise (100 kHz Offset)
Supply Current (Icc)
4 - 40
Typ.
4.95 - 5.3
Pin= 0 dBm
46
61
46
61
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
mA
HMC369LP3 / 369LP3E
v04.0210
SMT GaAs HBT MMIC x2 ACTIVE
FREQUENCY MULTIPLIER, 9.9 - 12.7 GHz OUTPUT
Output Power vs. Drive Level
8
8
7
7
6
6
5
4
3
2
1
+25 C
+85 C
-40 C
0
-1
-2
9.5
4
5
4
3
2
-10 dBm
-5 dBm
0 dBm
+5 dBm
1
0
-1
10
10.5
11
11.5
12
12.5
-2
9.5
13
10
OUTPUT FREQUENCY (GHz)
10.5
11
11.5
12
12.5
13
OUTPUT FREQUENCY (GHz)
Output Power vs.
Supply Voltage @ 0 dBm Drive Level
Input Return Loss vs. Temperature
0
8
-5
RETURN LOSS (dB)
6
5
4
3
2
1
Vcc=4.5V
Vcc=5.0V
Vcc=5.5V
0
+25 C
+85 C
-40 C
-10
-15
-20
-25
-1
-2
9.5
-30
10
10.5
11
11.5
12
12.5
3
13
3.5
4
4.5
5
5.5
FREQUENCY (GHz)
OUTPUT FREQUENCY (GHz)
6
6.5
7
Output Return Loss vs. Temperature
0
-1
-2
RETURN LOSS (dB)
OUTPUT POWER (dBm)
7
FREQ. MULTIPLIERS - ACTIVE - SMT
OUTPUT POWER (dBm)
OUTPUT POWER (dBm)
Output Power vs.
Temperature @ 0 dBm Drive Level
+25 C
+85 C
-40 C
-3
-4
-5
-6
-7
-8
-9
-10
9.5
10
10.5
11
11.5
12
12.5
13
FREQUENCY (GHz)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
4 - 41
HMC369LP3 / 369LP3E
v04.0210
SMT GaAs HBT MMIC x2 ACTIVE
FREQUENCY MULTIPLIER, 9.9 - 12.7 GHz OUTPUT
SSB Phase Noise
Performance, Fout= 10.66 GHz,
Input Power= 0 dBm
Output Spectrum
4 - 42
10
0
0
-20
SSB PHASE NOISE (dBc/Hz)
OUTPUT POWER (dBm)
FREQ. MULTIPLIERS - ACTIVE - SMT
4
-10
-20
-30
-40
-60
-80
-100
-40
-120
-50
-140
-60
0
2
4
6
8
10
12
14 16 18
FREQUENCY (GHz)
20 22 24
26
-160
2
10
3
10
4
10
5
10
6
10
OFFSET FREQUENCY (Hz)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
7
10
HMC369LP3 / 369LP3E
v04.0210
SMT GaAs HBT MMIC x2 ACTIVE
FREQUENCY MULTIPLIER, 9.9 - 12.7 GHz OUTPUT
Typical Supply Current vs. Vcc
RF Input (Vcc = +5V)
+20 dBm
Vcc (V)
Icc (mA)
Vcc
+5.5V
4.5
45
Channel Temperature
135 °C
5.0
46
5.5
47
Continuous Pdiss (T=85 °C)
(derate 6.8 mW/°C above 85 °C)
440 mW
Thermal Resistance (Rth)
(junction to ground paddle)
147.8 °C/W
Storage Temperature
-65 to +150 °C
Operating Temperature
-40 to +85 °C
Note: Multiplier will operate over full voltage range shown
above.
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Outline Drawing
4
FREQ. MULTIPLIERS - ACTIVE - SMT
Absolute Maximum Ratings
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS]
3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE.
4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM.
PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM.
5. PACKAGE WARP SHALL NOT EXCEED 0.05mm.
6. ALL GROUND LEADS AND GROUND PADDLE MUST BE
SOLDERED TO PCB RF GROUND.
7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED
LAND PATTERN.
Package Information
Part Number
Package Body Material
Lead Finish
MSL Rating
HMC369LP3
Low Stress Injection Molded Plastic
Sn/Pb Solder
MSL1
HMC369LP3E
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
MSL1
Package Marking [3]
[1]
369
XXXX
[2]
369
XXXX
[1] Max peak reflow temperature of 235 °C
[2] Max peak reflow temperature of 260 °C
[3] 4-Digit lot number XXXX
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
4 - 43
HMC369LP3 / 369LP3E
v04.0210
SMT GaAs HBT MMIC x2 ACTIVE
FREQUENCY MULTIPLIER, 9.9 - 12.7 GHz OUTPUT
Pin Description
FREQ. MULTIPLIERS - ACTIVE - SMT
4
4 - 44
Pin Number
Function
Description
1, 2, 5 - 8,
11 - 13, 15, 16
N/C
The pins are not connected internally; however, all
data shown herein was measured with these pins
connected to RF/DC ground externally.
3
RFIN
RF input needs to be DC blocked only if there is an
external DC voltage applied to RFIN.
4, 9
GND
All ground leads and ground paddle must be soldered
to PCB RF/DC ground.
10
RFOUT
Multiplied Output. AC coupled.
No external DC blocks necessary.
14
Vcc
Supply voltage 5V ± 0.5V.
Interface Schematic
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC369LP3 / 369LP3E
v04.0210
SMT GaAs HBT MMIC x2 ACTIVE
FREQUENCY MULTIPLIER, 9.9 - 12.7 GHz OUTPUT
Evaluation PCB
FREQ. MULTIPLIERS - ACTIVE - SMT
4
List of Materials for Evaluation PCB 107712 [1]
Item
Description
J1, J2
PCB Mount SMA Connector
J3, J4
DC Pin
C1
0.01 μF Capacitor, 0603 Pkg.
U1
HMC369LP3 / HMC369LP3E
x2 Active Multiplier
PCB [2]
107710 Eval Board
[1] Reference this number when ordering complete evaluation PCB
The circuit board used in the final application
should be generated with proper RF circuit design
techniques. Signal lines should have 50 ohm
impedance while the package ground leads and
exposed paddle should be connected directly to the
ground plane similar to that shown. The evaluation
circuit board shown is available from Hittite upon
request.
[2] Circuit Board Material: Rogers 4350
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
4 - 45