TE Analog Devices Welcomes Hittite Microwave Corporation O B SO LE NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com TE O B SO LE THIS PAGE INTENTIONALLY LEFT BLANK HMC488MS8G / 488MS8GE v03.0608 Features The HMC488MS8G / HMC488MS8GE is ideal for: Low Conversion Loss: 7 dB • Basestations & Repeaters Double-Balanced Topology • Access Points & Subscribers Integrated LO Amplifier: 0 to +6 dBm Drive • UNII, ISM, WLAN & WiMAX Input IP3: +15 dBm 9 • Point to Point/Multi-Point Radios Single Supply: +5V @ 46 mA • VSAT Radio MSOP8-G Package: 14.8 mm2 Functional Diagram General Description TE Typical Applications MIXERS - DBL-BAL - SMT GaAs MMIC MIXER W/ INTEGRATED LO AMPLIFIER, 4 - 7 GHz B SO LE The HMC488MS8G(E) is an ultra miniature doublebalanced mixer with integrated LO amplifier in an 8 lead plastic SMT MSOP8-G covering 4 - 7 GHz. This passive MMIC mixer integrates a GaAs Schottky diode quad, transformer baluns and a LO buffer on a single chip yielding a low conversion loss of 7 dB coupled with an input IP3 of +15 dBm. The LO buffer amplifier can be driven from 0 to +6 dBm and requires a single supply of +5V @ 46 mA. The device can be used as an upconverter, downconverter or bi-phase (de)modulator for a variety of point-to-point/ multipoint, VSAT, telemetry or broadband WLAN applications. O Electrical Specifi cations, TA = +25° C, IF= 100 MHz, Vdd= 5V LO = +2 dBm LO = 0 dBm Parameter Units Min. Frequency Range, RF & LO Frequency Range, IF Max. Min. Typ. Max. 4-7 5-6 GHz DC - 2.5 DC - 2.5 GHz Conversion Loss 7 Noise Figure (SSB) 7 9.5 8 10.5 dB 8 dB LO to RF Isolation 25 30 27 32 dB LO to IF Isolation 16 20 20 25 dB 15 dBm IP3 (Input) 15 1 dB Gain Compression (Input) Supply Current (Idd) 9 - 300 Typ. 5 8 46 6 60 9 46 dBm 60 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com mA HMC488MS8G / 488MS8GE v03.0608 GaAs MMIC MIXER W/ INTEGRATED LO AMPLIFIER, 4 - 7 GHz Conversion Gain vs. Temperature @ LO = +2 dBm Isolation @ LO = +2 dBm 0 -10 +25 C +85 C -40 C -15 RF TO IF LO TO RF LO TO IF -50 4.5 5 5.5 6 RF FREQUENCY (GHz) 6.5 7 4 4.5 5 5.5 6 FREQUENCY (GHz) LE 4 Conversion Gain vs. LO Drive 6.5 7 6.5 7 Return Loss @ LO = +2 dBm 0 0 -5 -5 B SO CONVERSION GAIN (dB) 9 -30 -40 -20 -10 0 dBm +2 dBm +4 dBm +6 dBm -15 -20 4 4.5 5 5.5 6 RF FREQUENCY (GHz) 6.5 RF LO -10 -15 -20 -25 4 7 Upconverter Performance Conversion Gain vs. LO Drive 4.5 5 5.5 6 FREQUENCY (GHz) O IF Bandwidth @ LO = +2 dBm 0 0 CONVERSION GAIN RETURN LOSS -5 -5 RESPONSE (dB) CONVERSION GAIN (dB) -20 TE -10 MIXERS - DBL-BAL - SMT ISOLATION (dB) -5 RETURN LOSS (dB) CONVERSION GAIN (dB) 0 -10 0 dBm +2 dBm +4 dBm +6 dBm -15 -10 -15 -20 -25 -20 4 4.5 5 5.5 6 RF FREQUENCY (GHz) 6.5 7 0 0.5 1 1.5 2 2.5 3 IF FREQUENCY (GHz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 3.5 4 9 - 301 HMC488MS8G / 488MS8GE v03.0608 GaAs MMIC MIXER W/ INTEGRATED LO AMPLIFIER, 4 - 7 GHz Input IP3 vs. LO Drive 25 20 20 IP3 (dBm) 25 15 +25 C +85 C -40 C 10 0 4.5 5 5.5 6 FREQUENCY (GHz) 6.5 7 4 4.5 5 5.5 6 FREQUENCY (GHz) 6.5 7 6.5 7 6.5 7 LE 4 Input IP2 vs. Temperature @ LO = +2 dBm Input IP2 vs. LO Drive 70 65 65 60 60 0 dBm +2 dBm +4 dBm 45 40 35 B SO 50 IP2 (dBm) 55 55 25 4.5 5 5.5 6 FREQUENCY (GHz) 6.5 50 45 40 35 +25 C +85 C -40 C 30 30 25 7 Input P1dB vs. Temperature @ LO = +2 dBm 4 O 12.5 12.5 10 10 P1dB (dBm) 15 7.5 +25 C +85 C -40 C 5 4.5 5 5.5 6 FREQUENCY (GHz) Input P1dB vs. LO Drive 15 P1dB (dBm) 0 dBm +2 dBm +4 dBm 5 0 4 2.5 7.5 0 dBm +2 dBm +3 dBm 5 2.5 0 0 4 9 - 302 15 TE 10 5 IP2 (dBm) MIXERS - DBL-BAL - SMT 9 IP3 (dBm) Input IP3 vs. Temperature @ LO = +2 dBm 4.5 5 5.5 6 FREQUENCY (GHz) 6.5 7 4 4.5 5 5.5 6 FREQUENCY (GHz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC488MS8G / 488MS8GE v03.0608 GaAs MMIC MIXER W/ INTEGRATED LO AMPLIFIER, 4 - 7 GHz MxN Spurious @ IF Port Harmonics of LO nLO Spur @ RF Port 1 2 3 4 0 xx 9 1 12 0 20 24 40 5 32 18 42 52 29 52 41 5.2 32 19 62 56 2 62 60 63 60 77 5.4 31 23 52 59 3 77 83 74 63 75 5.6 4 83 83 84 85 82 5.8 31 26 43 64 31 26 40 6 31 57 27 43 51 RF Freq. = 5.3 GHz @ -10 dBm LO Freq. = 5.2 GHz @ +3 dBm All values in dBc relative to the IF power level. LO Freq. (GHz) 1 2 3 TE 0 Typical Supply Current vs. Vdd Idd (mA) 45 +5.0 46 +5.25 47 B SO Vdd +4.75 LE LO = +3 dBm All values in dBc below input LO level measured at RF port. 9 O Mixer will operate over full voltage range shown above. 4 MIXERS - DBL-BAL - SMT nLO mRF For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 9 - 303 HMC488MS8G / 488MS8GE v03.0608 GaAs MMIC MIXER W/ INTEGRATED LO AMPLIFIER, 4 - 7 GHz Absolute Maximum Ratings +15 dBm +7 Vdc Channel Temperature 150°C Continuous Pdiss (T = 85°C) (derate 13.2 mW/°C above 85°C) 0.85 W Thermal Resistance (channel to ground paddle) 75.5 °C/W Storage Temperature -65 to +150°C Operating Temperature -40 to +85°C ESD Sensitivity (HBM) Class 1A LE Vdd ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS TE +13 dBm LO Drive (Vdd= +5V) B SO Outline Drawing NOTES: O MIXERS - DBL-BAL - SMT 9 RF / IF Input (Vdd= +5V) 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.15mm PER SIDE. 4. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.25mm PER SIDE. 5. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. Package Information Part Number Package Body Material Lead Finish MSL Rating HMC488MS8G Low Stress Injection Molded Plastic Sn/Pb Solder MSL1 HMC488MS8GE RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 Package Marking [3] [1] H488 XXXX [2] H488 XXXX [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX 9 - 304 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC488MS8G / 488MS8GE v03.0608 GaAs MMIC MIXER W/ INTEGRATED LO AMPLIFIER, 4 - 7 GHz Pin Descriptions Description Interface Schematic 1 LO This pin is AC coupled and matched to 50 Ohms. 2, 6, 7 GND This pin must be connected to RF ground. These pins are power supply for LO amp. An external RF bypass capacitor (10,000 pF) is required. 5 IF This pin is DC coupled. For applications not requiring operation to DC this port should be DC blocked externally using a series capacitor. Choose value of capacitor to pass IF frequency desired. For operation to DC, this pin must not sink/source more than 40 mA of current or failure may result. 8 RF This pin is DC coupled and matched to 50 Ohms. O B SO LE Vdd 3, 4 9 MIXERS - DBL-BAL - SMT Function TE Pin Number For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 9 - 305 HMC488MS8G / 488MS8GE v03.0608 GaAs MMIC MIXER W/ INTEGRATED LO AMPLIFIER, 4 - 7 GHz Evaluation PCB B SO LE MIXERS - DBL-BAL - SMT TE 9 O List of Materials for Evaluation PCB 108190 [1] Item Description J1 - J3 PCB Mount SMA RF Connector J4 - J5 DC Pins C1 10,000 pF Chip Capacitor, 0603 Pkg. U1 HMC488MS8G / HMC488MS8GE PCB [2] 106829 Evaluation Board, 1.000” x 1.000” [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 9 - 306 The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC488MS8G / 488MS8GE v03.0608 GaAs MMIC MIXER W/ INTEGRATED LO AMPLIFIER, 4 - 7 GHz MIXERS - DBL-BAL - SMT 9 O B SO LE TE Notes: For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 9 - 307