PDF Data Sheet

Analog Devices Welcomes
Hittite Microwave Corporation
NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
www.analog.com
www.hittite.com
THIS PAGE INTENTIONALLY LEFT BLANK
HMC498LC4
v04.0514
LINEAR & POWER AMPLIFIERS - SMT
GaAs PHEMT MEDIUM
POWER AMPLIFIER, 17 - 24 GHz
Typical Applications
Features
The HMC498LC4 is ideal for use as a LNA or Driver
amplifier for:
Output IP3: +36 dBm
• Point-to-Point Radios
Gain: 22 dB
• Point-to-Multi-Point Radios & VSAT
+5V @ 250 mA Supply
• Test Equipment & Sensors
50 Ohm Matched Input/Output
• Military End-Use
RoHS Compliant 4x4 mm SMT Package
Functional Diagram
General Description
Saturated Power: +26 dBm @ 23% PAE
The HMC498LC4 is a high dynamic range GaAs
PHEMT MMIC Medium Power Amplifier housed in a
leadless “Pb free” SMT package. Operating from 17
to 24 GHz, the amplifier provides 22 dB of gain, +26
dBm of saturated power and 23% PAE from a +5V
supply voltage. Noise figure is 4 dB while output IP3 is
+36 dBm typical enabling the HMC498LC4 to function
as a low noise front end as well as a driver amplifier.
The RF I/Os are DC blocked and matched to 50 Ohms
for ease of use. The HMC498LC4 eliminates the
need for wire bonding, allowing use of surface mount
manufacturing techniques.
Electrical Specifications, TA = +25° C, Vdd1, 2, 3 = 5V, Idd = 250 mA*
Parameter
Min.
Frequency Range
Gain
18
Gain Variation Over Temperature
Min.
20
0.03
25
Max.
Min.
18
0.03
10
15
24.5
Max.
22.5
Units
GHz
21
0.02
13
21.5
Typ.
23 - 24
22.5
0.02
15
22
Typ.
19 - 23
13
Output Return Loss
Saturated Output Power (Psat)
Max.
22
0.02
Input Return Loss
Output Power for 1 dB Compression (P1dB)
Typ.
17 - 19
dB
0.03
dB/ °C
dB
20
dB
25.5
dBm
26.5
25.5
26.5
dBm
Output Third Order Intercept (IP3)
35
36
35.5
dBm
Noise Figure
4.0
4.0
4.5
dB
Supply Current (Idd)(Vdd = +5V, Vgg = -0.8V
Typ.)
250
250
250
mA
* Adjust Vgg between -2 to 0V to achieve Idd = 250 mA typical.
1
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC498LC4
v04.0514
GaAs PHEMT MEDIUM
POWER AMPLIFIER, 17 - 24 GHz
Broadband Gain & Return Loss
Gain vs. Temperature
25
22
S21
S11
S22
5
GAIN (dB)
RESPONSE (dB)
15
-5
18
+25 C
+85 C
-40 C
14
-15
-25
10
12
14
16
18
20
22
24
26
28
16
17
18
FREQUENCY (GHz)
21
22
23
24
25
Output Return Loss vs. Temperature
0
0
-5
+25 C
+85 C
-40 C
-5
RETURN LOSS (dB)
RETURN LOSS (dB)
20
FREQUENCY (GHz)
Input Return Loss vs. Temperature
-10
-15
+25 C
+85 C
-40 C
-10
-15
-20
-25
-20
16
17
18
19
20
21
22
23
24
16
25
17
18
P1dB vs. Temperature
20
21
22
23
24
23
24
25
Psat vs. Temperature
30
26
26
Psat (dBm)
30
22
+25 C
+85 C
-40 C
18
19
FREQUENCY (GHz)
FREQUENCY (GHz)
P1dB (dBm)
19
LINEAR & POWER AMPLIFIERS - SMT
26
14
22
+25 C
+85 C
-40 C
18
14
10
10
16
17
18
19
20
21
22
FREQUENCY (GHz)
23
24
25
16
17
18
19
20
21
22
25
FREQUENCY (GHz)
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
2
HMC498LC4
v04.0514
GaAs PHEMT MEDIUM
POWER AMPLIFIER, 17 - 24 GHz
Output IP3 vs. Temperature
Noise Figure vs. Temperature
10
9
32
+25 C
+85 C
-40 C
28
24
-40 C
7
6
5
4
3
2
1
20
0
16
17
18
19
20
21
22
23
24
25
16
17
18
19
FREQUENCY (GHz)
Gain, Power & OIP3
vs. Supply Voltage @ 23 GHz
21
22
23
24
25
24
25
Reverse Isolation vs. Temperature
40
0
-10
32
ISOLATION (dB)
36
Gain
P1dB
Psat
IP3
28
24
-20
+25 C
+85 C
-40 C
-30
-40
-50
-60
20
4.5
5
-70
5.5
16
Vdd Supply Voltage (Vdc)
18
19
20
21
22
23
Power Compression @ 23 GHz
Pout (dBm), GAIN (dB), PAE (%)
30
25
20
15
10
Pout (dBm)
Gain (dB)
PAE (%)
5
0
-10
17
FREQUENCY (GHz)
30
Pout (dBm), GAIN (dB), PAE (%)
20
FREQUENCY (GHz)
Power Compression @ 18 GHz
-8
-6
-4
-2
0
2
INPUT POWER (dBm)
3
+25 C
+85 C
8
NOISE FIGURE (dB)
IP3 (dBm)
36
Gain (dB), P1dB (dBm), Psat (dBm), IP3 (dBm)
LINEAR & POWER AMPLIFIERS - SMT
40
4
6
8
10
25
20
15
10
Pout (dBm)
Gain (dB)
PAE (%)
5
0
-10
-8
-6
-4
-2
0
2
4
6
8
10
INPUT POWER (dBm)
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC498LC4
v04.0514
GaAs PHEMT MEDIUM
POWER AMPLIFIER, 17 - 24 GHz
Typical Supply Current vs. Vdd
Drain Bias Voltage (Vdd1, Vdd2, Vdd3)
+5.5 Vdc
Gate Bias Voltage (Vgg)
-4.0 to 0 Vdc
Vdd (Vdc)
Idd (mA)
+4.5
239
RF Input Power (RFIN)(Vdd = +5Vdc)
+10 dBm
+5.0
250
Channel Temperature
175 °C
+5.5
262
Continuous Pdiss (T= 85 °C)
(derate 18 mW/°C above 85 °C)
1.62 W
Thermal Resistance
(channel to ground paddle)
55.6 °C/W
Storage Temperature
-65 to +150 °C
Operating Temperature
-40 to +85 °C
ESD Sensitivity (HBM)
Class 1A
Note: Amplifier will operate over full voltage ranges shown
above. Vgg adjusted to achieve Idd= 250 mA at +5V.
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Outline Drawing
LINEAR & POWER AMPLIFIERS - SMT
Absolute Maximum Ratings
NOTES:
1. PACKAGE BODY MATERIAL: ALUMINA.
2. LEAD AND GROUND PADDLE PLATING: GOLD FLASH OVER NICKEL.
3. DIMENSIONS ARE IN INCHES (MILLIMETERS).
4. LEAD SPACING TOLERANCE IS NON-CUMULATIVE.
5. CHARACTERS TO BE HELVETICA MEDIUM, .025 HIGH, BLACK INK, OR LASER MARK
LOCATED APPROX. AS SHOWN.
6. PACKAGE WARP SHALL NOT EXCEED 0.05MM DATUM – C –
7. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND.
Package Information
Part Number
Package Body Material
Lead Finish
HMC498LC4
Alumina, White
Gold over Nickel
MSL Rating
MSL3
[1]
Package Marking [2]
H498
XXXX
[1] Max peak reflow temperature of 260 °C
[2] 4-Digit lot number XXXX
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
4
HMC498LC4
v04.0514
GaAs PHEMT MEDIUM
POWER AMPLIFIER, 17 - 24 GHz
Pin Descriptions
LINEAR & POWER AMPLIFIERS - SMT
Pin Number
5
Function
Description
1, 5 - 8, 10 - 14,
18, 20, 22, 24
N/C
These pins are not connected internally; however, all data
shown herein was measured with these pins connected to
RF/DC ground externally.
2, 4, 15, 17
GND
Package bottom has an exposed metal paddle that must
also be connected to RF/DC ground.
3
RFIN
This pin is AC coupled
and matched to 50 Ohms.
9
Vgg
Gate control for amplifier. Adjust to achieve Id of 250 mA.
Please follow “MMIC Amplifier Biasing Procedure”
Application Note. External bypass capacitors of 100 pF,
1000 pF and 2.2 µF are required.
16
RFOUT
This pin is AC coupled
and matched to 50 Ohms.
23, 21, 19
Vdd1, Vdd2, Vdd3
Power Supply Voltage for the amplifier. External bypass
capacitors of 100 pF, 1000pF, and 2.2 µF are required.
Interface Schematic
Application Circuit
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC498LC4
v04.0514
GaAs PHEMT MEDIUM
POWER AMPLIFIER, 17 - 24 GHz
LINEAR & POWER AMPLIFIERS - SMT
Evaluation PCB
List of Materials for Evaluation PCB 108537 [1]
Item
Description
J1, J2
2.92 mm PC mount K-connector
J3 - J8
DC Pin
C1 - C4
100 pF capacitor, 0402 pkg.
C5 - C8
1,000 pF Capacitor, 0603 pkg.
C9 - C12
2.2µF Capacitor, Tantalum
U1
HMC498LC4 Amplifier
PCB [2]
108535 Evaluation PCB
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Rogers 4350.
The circuit board used in this application should use
RF circuit design techniques. Signal lines should
have 50 Ohm impedance while the package ground
leads and exposed paddle should be connected
directly to the ground plane similar to that shown.
A sufficient number of via holes should be used to
connect the top and bottom ground planes. The
evaluation board should be mounted to an appropriate heat sink. The evaluation circuit board shown
is available from Hittite upon request.
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
6