Not for New Designs TSOP852.., TSOP854.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES 2 1 Very low supply current Photo detectors and preamplifier in one package Internal filter for PCM frequency Supply voltage: 2.5 V to 5.5 V Improved immunity against ambient light Capable of side or top view Two lenses for high sensitivity and wide receiving angle • Insensitive to supply voltage ripple and noise • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 5 4 3 • • • • • • • 20427-1 MECHANICAL DATA DESCRIPTION Pinning These products are miniaturized receivers for infrared remote control systems. A PIN diode and a preamplifier are assembled on a lead frame, the epoxy package acts as an IR filter. The demodulated output signal can be directly connected to a microprocessor. The TSOP852.. are legacy products for all common IR remote control data formats. The TSOP854.. is optimized to suppress almost all spurious pulses from energy saving fluorescent lamps. They may suppress some data signals. This component has not been qualified according to automotive specifications. 1, 4, 5 = GND, 2 = VS, 3 = OUT PARTS TABLE AGC Carrier frequency Package 30 kHz 33 kHz 36 kHz 38 kHz 40 kHz 56 kHz Pinning Dimensions (mm) Mounting Application Best remote control code LEGACY, FOR RECOMMENDED FOR LONG BURST REMOTE CONTROLS (AGC2) LONG BURST CODES (AGC4) (1) TSOP85230 TSOP85430 TSOP85233 TSOP85433 TSOP85236 TSOP85436 (2)(3)(4) TSOP85238 TSOP85438 (5)(6)(9) TSOP85240 TSOP85440 TSOP85256 TSOP85456 (7)(8) 1, 4, 5 = GND, 2 = VS, 3 = OUT 8.0 H x 3.3 W x 2.7 L SMD Remote control (2) RC-5 (3) RC-6 (4) Panasonic (5) NEC (6) Sharp (7) r-step (8) Thomson RCA (9) r-map Note (1) We advise try AGC4 first if the burst length is unknown BLOCK DIAGRAM APPLICATION CIRCUIT 17170_5 2 Transmitter with TSALxxxx VS 30 kΩ Input AGC Band pass Demodulator VS Circuit 3 R1 IR receiver OUT + VS C1 µC OUT GND VO GND 1, 4, 5 PIN Control circuit GND R1 and C1 are recommended for protection against EOS. Components should be in the range of 33 Ω < R1 < 1 kΩ, C1 > 0.1 µF. 20445 Rev. 1.8, 27-Feb-15 1 Document Number: 81764 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Designs TSOP852.., TSOP854.. www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT VS -0.3 to +6 V mA Supply voltage Supply current IS 3 Output voltage VO -0.3 to (VS + 0.3) V Output current IO 5 mA Junction temperature Tj 100 °C Tstg -25 to +85 °C Tamb -25 to +85 °C Ptot 10 mW Tsd 260 °C Storage temperature range Operating temperature range Tamb ≤ 85 °C Power consumption Soldering temperature Note • Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability. ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL MIN. VS 2.5 VS = 3.3 V, Ev = 0 ISD 0.27 Ev = 40 klx, sunlight ISH 0.45 mA Ev = 0 IR diode TSAL6200, IF = 250 mA test signal see fig. 1 d 45 m Output voltage low IOSL = 0.5 mA, Ee = 0.7 mW/m2, test signal see fig. 1 VOSL Minimum irradiance Pulse width tolerance: tpi - 5/fo < tpo < tpi + 6/fo test signal see fig. 1 Ee min. Maximum irradiance tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 1 Ee max. Directivity Angle of half transmission distance ϕ1/2 Supply voltage Supply current Transmission distance TYP. MAX. 0.35 0.1 UNIT 5.5 V 0.45 mA 100 mV 0.25 mW/m2 W/m2 30 ± 50 deg TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) Optical Test Signal 1 (IR diode TSAL6200, IF = 0.4 A, 30 pulses, f = f0, t = 10 ms) tpo - Output Pulse Width (ms) Ee t tpi * * tpi VO T 10/f0 is recommended for optimal function Output Signal 1) VOH 2) 16110 Output Pulse Width 0.9 0.8 Input Burst Length 0.7 0.6 0.5 0.4 0.3 λ = 950 nm, Optical Test Signal, Fig. 1 0.2 0.1 7/f0 < td < 15/f0 tpi - 5/f0 < tpo < tpi + 6/f0 0 0.1 VOL td 1) tpo 2) 20743 t Fig. 1 - Output Active Low Rev. 1.8, 27-Feb-15 1 10 100 1000 10 000 Ee - Irradiance (mW/m²) Fig. 2 - Pulse Length and Sensitivity in Dark Ambient 2 Document Number: 81764 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Designs TSOP852.., TSOP854.. www.vishay.com Optical Test Signal 600 µs t 600 µs t = 60 ms 94 8134 Output Signal, (see fig. 4) VO VOH VOL t off t on 4 Ee min. - Threshold Irradiance (mW/m²) Ee Vishay Semiconductors Correlation with Ambient Light Sources: 3.5 10 W/m² = 1.4 klx (Std. illum. A, T = 2855 K) 10 W/m² = 8.2 klx (Daylight, T = 5900 K) 3 Wavelength of Ambient Illumination: λ = 950 nm 2.5 2 1.5 1 0.5 0 0.01 t 20745 Fig. 3 - Output Function Ee min. - Threshold Irradiance (mW/m²) Ton, Toff - Output Pulse Width (ms) Ton 0.7 0.6 0.5 Toff 0.4 0.3 0.2 λ = 950 nm, Optical Test Signal, Fig. 3 0 0.1 20744 1 10 100 1000 10 100 1 f = 100 Hz 0.9 0.8 f = 10 kHz 0.7 0.6 f = 20 kHz 0.5 0.4 f = 30 kHz 0.3 0.2 f = f0 0.1 0 10 000 1 Ee - Irradiance (mW/m²) 10 100 1000 Δ VsRMS - AC Voltage on DC Supply Voltage (mV) 20746 Fig. 4 - Output Pulse Diagram Fig. 7 - Sensitivity vs. Supply Voltage Disturbances 1.2 500 E - Max. Field Strength (V/m) E e min./Ee - Rel. Responsivity 1 Fig. 6 - Sensitivity in Bright Ambient 0.8 0.1 0.1 Ee - Ambient DC Irradiance (W/m²) 1.0 0.8 0.6 0.4 f = f0 ± 5 % Δ f(3 dB) = f0/10 0.2 450 400 350 300 250 200 150 100 50 0.0 0 0.7 16925 0.9 1.1 1.3 0 20747 f/f0 - Relative Frequency Fig. 5 - Frequency Dependance of Responsivity Rev. 1.8, 27-Feb-15 500 1000 1500 2000 2500 3000 f - EMI Frequency (MHz) Fig. 8 - Sensitivity vs. Electric Field Disturbances 3 Document Number: 81764 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Designs TSOP852.., TSOP854.. www.vishay.com Vishay Semiconductors 1.0 S(λ)rel - Relative Spectral Sensitivity 1 Max. Envelope Duty Cycle 0.9 0.8 0.7 0.6 0.5 TSOP852.. 0.4 0.3 TSOP854.. 0.2 0.1 2 f = 38 kHz, Ee = 2 mW/m 0 0 20817 20 40 60 80 100 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 700 750 800 850 900 950 1000 1050 1100 120 Burst Length (number of cycles/burst) λ - Wavelength (nm) 20431 Fig. 9 - Max. Envelope Duty Cycle vs. Burst Length Ee min. - Threshold Irradiance (mW/m²) 0.9 Fig. 11 - Relative Spectral Sensitivity vs. Wavelength 0.2 0.18 0° 0.16 - 20° 20° 0.14 - 40° 0.12 40° 0.1 - 60° 0.08 60° 0.06 0.04 - 80° 80° 0.02 0 - 30 20749 20432 - 10 10 30 50 70 0.3 0.5 0.7 0.9 Tamb - Ambient Temperature (°C) Fig. 10 - Sensitivity vs. Ambient Temperature Rev. 1.8, 27-Feb-15 0.1 90 Fig. 12 - Directivity 4 Document Number: 81764 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Designs TSOP852.., TSOP854.. www.vishay.com Vishay Semiconductors SUITABLE DATA FORMAT IR Signal The TSOP852.., TSOP854 series are designed to suppress spurious output pulses due to noise or disturbance signals. Data and disturbance signals can be distinguished by the devices according to carrier frequency, burst length and envelope duty cycle. The data signal should be close to the band-pass center frequency (e.g. 38 kHz) and fulfill the conditions in the table below. When a data signal is applied to the TSOP852.., TSOP854 in the presence of a disturbance signal, the sensitivity of the receiver is reduced to insure that no spurious pulses are present at the output. Some examples of disturbance signals which are suppressed are: 0 • DC light (e.g. from tungsten bulb or sunlight) 5 10 15 20 Time (ms) 16920 • Continuous signals at any frequency Fig. 13 - IR Signal from Fluorescent Lamp with Low Modulation IR Signal • Strongly or weakly modulated noise from fluorescent lamps with electronic ballasts (see fig. 13 or fig. 14) 0 5 16921 10 15 20 Time (ms) Fig. 14 - IR Signal from Fluorescent Lamp with High Modulation TSOP852.. TSOP854.. Minimum burst length 10 cycles/burst 10 cycles/burst After each burst of length a minimum gap time is required of 10 to 70 cycles ≥ 10 cycles 10 to 35 cycles ≥ 10 cycles For bursts greater than a minimum gap time in the data stream is needed of 70 cycles > 4 x burst length 35 cycles > 10 x burst length Maximum number of continuous short bursts/second 1800 1500 Recommended for NEC code yes yes Recommended for RC5/RC6 code yes yes Recommended for Thomson 56 kHz code yes yes Recommended for Mitsubishi code (38 kHz, preburst 8 ms, 16 bit) yes no Recommended for Sharp code yes yes Most common disturbance signals are suppressed Even extreme disturbance signals are suppressed Suppression of interference from fluorescent lamps Notes • For data formats with short bursts please see the datasheet for TSOP853.., TSOP855.. • Example of compatible products for IR-codes: -TSOP85436: RC-5, RC-6, Panasonic -TSOP85438: NEC, Sharp, r-map -TSOP85456: r-step, Thomson RCA Rev. 1.8, 27-Feb-15 5 Document Number: 81764 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Designs TSOP852.., TSOP854.. www.vishay.com Vishay Semiconductors PACKAGE DIMENSIONS in millimeters (0.6) (5x) (0.5) technical drawings according to DIN specifications Not indicated to lerances ± 0.25 optional GND pad connection not necessary Marking area (R1.35) (4.9) (R1.35) (2.2) 1 min. 1.5 1 3.3 0 - 0.1 1 2 3 4 5 possible package deviations caused by 1.7 nom 1.7 nom. 1.7 nom. tolerances in the manufacturing process either on pick and place side or solder pad side 1.7 nom 2.74 8 Proposed pad layout from component side (dim. for reference only) (sideview assembly) 4 x 1.7 = 6.8 1.7 2 min. 1.5 5:1 0.7 (5x) (topview assembly) 1.1 Pick and Place area Drawing-No.: 6.550-5292.01-4 Issue: 3; 19.11.10 0.8 1.7 (5x) 20426 4 x 1.7 = 6.8 ASSEMBLY INSTRUCTIONS Reflow Soldering Manual Soldering • Reflow soldering must be done within 72 h while stored under a max. temperature of 30 °C, 60 % RH after opening the dry pack envelope • Use a soldering iron of 25 W or less. Adjust the temperature of the soldering iron below 300 °C • Set the furnace temperatures for pre-heating and heating in accordance with the reflow temperature profile as shown in the diagram. Exercise extreme care to keep the maximum temperature below 260 °C. The temperature shown in the profile means the temperature at the device surface. Since there is a temperature difference between the component and the circuit board, it should be verified that the temperature of the device is accurately being measured • Handle products only after the temperature has cooled off • Finish soldering within 3 s • Handling after reflow should be done only after the work surface has been cooled off Rev. 1.8, 27-Feb-15 6 Document Number: 81764 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Designs TSOP852.., TSOP854.. www.vishay.com Vishay Semiconductors VISHAY LEAD (Pb)-FREE REFLOW SOLDER PROFILE 300 max. 260 °C 245 °C 255 °C 240 °C 217 °C 250 T (°C) 200 max. 20 s 150 max. 100 s max. 120 s 100 max. Ramp Up 3 °C/s max. Ramp Down 6 °C/s 50 0 0 19800 50 100 150 t (s) 200 250 300 max. 2 cycles allowed TAPING VERSION TSOP..TR DIMENSIONS in millimeters 20628 Rev. 1.8, 27-Feb-15 7 Document Number: 81764 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Designs TSOP852.., TSOP854.. www.vishay.com Vishay Semiconductors TAPING VERSION TSOP..TT DIMENSIONS in millimeters 20629 Rev. 1.8, 27-Feb-15 8 Document Number: 81764 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Designs TSOP852.., TSOP854.. www.vishay.com Vishay Semiconductors LABEL Standard bar code labels for finished goods The standard bar code labels are product labels and used for identification of goods. The finished goods are packed in final packing area. The standard packing units are labeled with standard bar code labels before transported as finished goods to warehouses. The labels are on each packing unit and contain Vishay Semiconductor GmbH specific data. VISHAY SEMICONDUCTOR GmbH STANDARD BAR CODE PRODUCT LABEL (finished goods) PLAIN WRITING ABBREVIATION LENGTH Item-description - 18 Item-number INO 8 Selection-code SEL 3 LOT-/serial-number BATCH 10 COD 3 (YWW) Plant-code PTC 2 Quantity QTY 8 Accepted by ACC - Packed by PCK - MIXED CODE - xxxxxxx+ Company logo TYPE LENGTH Data-code Mixed code indicator Origin LONG BAR CODE TOP Item-number N 8 Plant-code N 2 Sequence-number X 3 Quantity N 8 Total length - 21 TYPE LENGTH Selection-code X 3 Data-code N 3 Batch-number X 10 Filter - 1 Total length - 17 SHORT BAR CODE BOTTOM DRY PACKING RECOMMENDED METHOD OF STORAGE The reel is packed in an anti-humidity bag to protect the devices from absorbing moisture during transportation and storage. Dry box storage is recommended as soon as the aluminum bag has been opened to prevent moisture absorption. The following conditions should be observed, if dry boxes are not available: Aluminum bag • Storage temperature 10 °C to 30 °C • Storage humidity ≤ 60 % RH max. Label After more than 72 h under these conditions moisture content will be too high for reflow soldering. In case of moisture absorption, the devices will recover to the former condition by drying under the following condition: Reel FINAL PACKING 192 h at 40 °C + 5 °C / - 0 °C and < 5 % RH (dry air / nitrogen) or 96 h at 60 °C + 5 °C and < 5 % RH for all device containers or 24 h at 125 °C + 5 °C not suitable for reel or tubes. The sealed reel is packed into a cardboard box. A secondary cardboard box is used for shipping purposes. An EIA JEDEC® standard JSTD-020 level 4 label is included on all dry bags. 15973 Rev. 1.8, 27-Feb-15 9 Document Number: 81764 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Designs TSOP852.., TSOP854.. www.vishay.com CAUTION This bag contains MOISTURE-SENSITIVE DEVICES Vishay Semiconductors VISHAY SEMICONDUCTORS STANDARD BAR CODE LABELS LEVEL 4 The Vishay Semiconductors standard bar code labels are printed at final packing areas. The labels are on each packing unit and contain Vishay Semiconductors specific data. 1. Shelf life in sealed bag: 12 months at < 40 °C and < 90 % relative humidity (RH) 2. After this bag is opened, devices that will be subjected to soldering reflow or equivalent processing (peak package body temp. 260 °C) must be 2a. Mounted within 72 hours at factory condition of < 30 °C/60 % RH or 2b. Stored at < 5 % RH BAR CODE PRODUCT LABEL (example) 3. Devices require baking befor mounting if: Humidity Indicator Card is > 10 % when read at 23 °C ± 5 °C or 2a. or 2b. are not met. 4. If baking is required, devices may be baked for: 192 hours at 40 °C + 5 °C/- 0 °C and < 5 % RH (dry air/nitrogen) or 96 hours at 60 °C ± 5 °C and < 5 % RH for all device containers or 24 hours at 125 °C ± 5 °C not suitable for reels or tubes Bag Seal Date: (If blank, see barcode label) Note: Level and body temperature defined by EIA JEDEC Standard J-STD-020 22522 EIA JEDEC standard JSTD-020 level 4 label is included on all dry bags 22178 ESD PRECAUTION Proper storage and handling procedures should be followed to prevent ESD damage to the devices especially when they are removed from the antistatic shielding bag. Electrostatic sensitive devices warning labels are on the packaging. Rev. 1.8, 27-Feb-15 10 Document Number: 81764 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000