OPTO Solid State Relay Lineup Package DIP 6-pin DIP 8-pin Applied voltage ON-state current (rms) Features Model No. Page AC 100 V lines 0.15 A General purpose PR22MA11NTZF 44 AC 200 V lines 0.06 A General purpose PR31MA11NTZF 44 0.15 A General purpose PR32MA11NTZF 44 0.3/0.6/0.9/1.2 A General purpose PR33MF5 series / PR39MF5 series / PR36MF5 series / PR3BMF5 series / PR36MF12NSZF 44 0.6/0.9/1.2 A Built-in zero-cross circuit PR36MF2 series / PR39MF2 series 44 AC 200 V lines Optoelectronics ■ SOLID STATE RELAY LINEUP 43 OPTO ■ Solid SOLID STATE RELAYS State Relays <DIP type> ○: Approved Approved by safety standards*1 Model No. Internal connection diagram Features UL CSA VDE*2 PR22MA11NTZF 100 V lines, 150 mA model in a small package ○ ○ ○ PR31MA11NTZF 200 V lines, compact ○ ○ ○ PR32MA11NTZF 200 V lines, 150 mA model in a small package ○ ○ ○ PR33MF51NSLF 200 V lines, compact ○ ○ ○ 200 V lines, compact ○ ○ ○ PR36MF51NSLF 200 V lines, compact ○ ○ ○ PR36MF12NSZF 200 V lines, compact, low input current ○ ○ ○ PR39MF51NSLF 200 V lines, compact ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ PR33MF52NSLF PR3BMF51NSLF 200 V lines, compact PR3BMF52NSZF PR36MF21NSZF PR36MF22NSZF PR39MF22NSZF Zerocross circuit 200 V lines, compact, low input current 200 V lines, compact (built-in zerocross circuit) 200 V lines, compact (built-in zerocross circuit), low input current 200 V lines, compact (built-in zerocross circuit), low input current (Ta = 25°C) Electrical Absolute maximum ratings characteristics Min. trigger Repetitive Isolation current Package ON-state voltage peak current IFT (AC) OFF-state (mA) MAX. IT (rms) voltage Viso (rms) (A) VD = 6 V, (kV) VDRM (V) RL = 100Ω 0.15 6-pin DIP 400 10 5.0 0.06 10 600 0.15 10 10 0.3 10 10 0.6 5 600 8-pin DIP 0.9 10 4.0 10 1.2 5 10 0.6 600 0.9 5 5 *1 Please refer to Specification Sheets for model numbers approved by safety standards. *2 Optionally available. PR22MA11NTZF (6-pin DIP) 44 PR26MF21NSZF (8-pin DIP) Notice In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP. *RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants (PBBs and PBDEs), with certain exceptions. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.