PD - 95091B IRLR7821PbF IRLU7821PbF ® Applications l High Frequency Synchronous Buck Converters for Computer Processor Power l High Frequency Isolated DC-DC Converters with Synchronous Rectification for Telecom and Industrial Use l Lead-Free HEXFET Power MOSFET VDSS RDS(on) max 10m: 30V Benefits l Very Low RDS(on) at 4.5V VGS l Ultra-Low Gate Impedance l Fully Characterized Avalanche Voltage and Current Qg 10nC D-Pak I-Pak IRLR7821PbF IRLU7821PbF Absolute Maximum Ratings Max. Units VDS Drain-to-Source Voltage Parameter 30 V VGS Gate-to-Source Voltage ± 20 ID @ TC = 25°C Continuous Drain Current, VGS @ 10V 65 ID @ TC = 100°C Continuous Drain Current, VGS @ 10V 47 IDM Pulsed Drain Current 260 PD @TC = 25°C Maximum Power Dissipation 75 PD @TC = 100°C Maximum Power Dissipation 37.5 TJ Linear Derating Factor Operating Junction and TSTG Storage Temperature Range c f f A W W/°C °C 0.50 -55 to + 175 Thermal Resistance Typ. Max. ––– 2.0 RθJA Junction-to-Case Junction-to-Ambient (PCB Mount) Parameter ––– 50 RθJA Junction-to-Ambient ––– 110 RθJC g Units °C/W Notes through are on page 11 www.irf.com 1 10/02/06 IRLR/U7821PbF Static @ TJ = 25°C (unless otherwise specified) Parameter Min. Typ. Max. Units Conditions BVDSS Drain-to-Source Breakdown Voltage 30 ––– ––– ∆ΒVDSS/∆TJ Breakdown Voltage Temp. Coefficient ––– 23 ––– RDS(on) Static Drain-to-Source On-Resistance ––– 7.5 10 mV/°C Reference to 25°C, ID = 1mA mΩ VGS = 10V, ID = 15A ––– 9.5 12.5 VGS = 4.5V, ID = 12A V VGS = 0V, ID = 250µA VGS(th) Gate Threshold Voltage 1.0 ––– ––– V ∆VGS(th) Gate Threshold Voltage Coefficient ––– -5.3 ––– mV/°C IDSS Drain-to-Source Leakage Current ––– ––– 1.0 µA VDS = 24V, VGS = 0V ––– ––– 150 IGSS Gate-to-Source Forward Leakage ––– ––– 100 nA VGS = 20V Gate-to-Source Reverse Leakage ––– ––– -100 gfs Qg Forward Transconductance 46 ––– ––– S VDS = 15V, ID = 12A f f VDS = VGS, ID = 250µA VDS = 24V, VGS = 0V, TJ = 125°C VGS = -20V Total Gate Charge ––– 10 14 Qgs1 Pre-Vth Gate-to-Source Charge ––– 2.0 ––– Qgs2 Post-Vth Gate-to-Source Charge ––– 1.2 ––– Qgd Gate-to-Drain Charge ––– 2.5 ––– ID = 12A Qgodr ––– 4.3 ––– See Fig. 16 Qsw Gate Charge Overdrive Switch Charge (Qgs2 + Qgd) ––– 3.7 ––– Qoss Output Charge ––– 8.5 ––– td(on) Turn-On Delay Time ––– 11 ––– VDD = 15V, VGS = 4.5V tr Rise Time ––– 4.2 ––– ID = 12A td(off) Turn-Off Delay Time ––– 10 ––– tf Fall Time ––– 3.2 ––– Ciss Input Capacitance ––– 1030 ––– Coss Output Capacitance ––– 360 ––– Crss Reverse Transfer Capacitance ––– 120 ––– VDS = 16V nC nC ns VGS = 4.5V VDS = 16V, VGS = 0V f Clamped Inductive Load VGS = 0V pF VDS = 15V ƒ = 1.0MHz Avalanche Characteristics EAS Parameter Single Pulse Avalanche Energy IAR Avalanche Current EAR Repetitive Avalanche Energy c dh c Typ. Max. Units ––– 230 mJ ––– 12 A ––– 7.5 mJ Diode Characteristics Parameter Min. Typ. Max. Units f Conditions IS Continuous Source Current ––– ––– 65 ISM (Body Diode) Pulsed Source Current ––– ––– 260 showing the integral reverse VSD (Body Diode) Diode Forward Voltage ––– ––– 1.0 V p-n junction diode. TJ = 25°C, IS = 12A, VGS = 0V trr Reverse Recovery Time ––– 26 38 ns Qrr Reverse Recovery Charge ––– 15 23 nC ton Forward Turn-On Time 2 ch MOSFET symbol A D G S f TJ = 25°C, IF = 12A, VDD = 15V di/dt = 100A/µs f Intrinsic turn-on time is negligible (turn-on is dominated by LS+LD) www.irf.com IRLR/U7821PbF 1000 10000 VGS 10V 4.5V 3.7V 3.5V 3.3V 3.0V 2.7V 2.5V 1000 100 BOTTOM 10 1 2.5V 100 BOTTOM 10 2.5V 20µs PULSE WIDTH Tj = 175°C 20µs PULSE WIDTH Tj = 25°C 0.1 0.1 1 10 1 0.1 100 1 Fig 1. Typical Output Characteristics 2.0 °C 10 °C V DS= 15V 20µs PULSE WIDTH 1 2.0 4.0 6.0 8.0 V GS, Gate-to-Source Voltage (V) Fig 3. Typical Transfer Characteristics www.irf.com 10.0 I D = 65A 1.5 (Normalized) R DS(on) , Drain-to-Source On Resistance I D , Drain-to-Source Current (A) TJ = 175 100 Fig 2. Typical Output Characteristics 1000 100 10 VDS, Drain-to-Source Voltage (V) VDS, Drain-to-Source Voltage (V) TJ = 25 VGS 10V 4.5V 3.7V 3.5V 3.3V 3.0V 2.7V 2.5V TOP ID, Drain-to-Source Current (A) ID, Drain-to-Source Current (A) TOP 1.0 0.5 V GS = 10V 0.0 -60 -40 -20 0 20 40 60 80 100 120 140 160 180 TJ, Junction Temperature (°C) Fig 4. Normalized On-Resistance Vs. Temperature 3 IRLR/U7821PbF 10000 6 VGS , Gate-to-Source Voltage (V) VGS = 0V, f = 1 MHZ Ciss = Cgs + Cgd, Cds SHORTED Crss = Cgd C, Capacitance(pF) Coss = Cds + Cgd Ciss 1000 Coss Crss 100 ID= 12A 4 3 2 1 0 10 1 10 0 100 4 6 8 10 12 Fig 6. Typical Gate Charge Vs. Gate-to-Source Voltage Fig 5. Typical Capacitance Vs. Drain-to-Source Voltage 1000 ID, Drain-to-Source Current (A) 1000 OPERATION IN THIS AREA LIMITED BY R DS(on) 100 100 I SD , Reverse Drain Current (A) 2 Q G Total Gate Charge (nC) VDS, Drain-to-Source Voltage (V) TJ = 175 ° C 10 T J= 25 ° C 1 V GS = 0 V 0.1 0.0 0.5 1.0 1.5 V SD,Source-to-Drain Voltage (V) Fig 7. Typical Source-Drain Diode Forward Voltage 4 VDS= 24V VDS= 16V 5 100µsec 10 1msec 1 10msec Tc = 25°C Tj = 175°C Single Pulse 0.1 2.0 1 10 100 VDS, Drain-to-Source Voltage (V) Fig 8. Maximum Safe Operating Area www.irf.com IRLR/U7821PbF 2.5 70 VGS(th) Gate threshold Voltage (V) LIMITED BY PACKAGE 60 I D , Drain Current (A) 50 40 30 20 10 2.0 ID = 250µA 1.5 1.0 0.5 0 25 50 75 100 125 150 175 -75 -50 -25 TC , Case Temperature ( °C) 0 25 50 75 100 125 150 175 200 T J , Temperature ( °C ) Fig 9. Maximum Drain Current Vs. Case Temperature Fig 10. Threshold Voltage Vs. Temperature (Z thJC ) 10 1 D = 0.50 Thermal Response 0.20 0.10 0.05 0.1 0.02 0.01 P DM SINGLE PULSE (THERMAL RESPONSE) t1 t2 Notes: 1. Duty factor D = 2. Peak T 0.01 0.00001 0.0001 0.001 0.01 t1/ t 2 J = P DM x Z thJC +T C 0.1 1 t1, Rectangular Pulse Duration (sec) Fig 11. Maximum Effective Transient Thermal Impedance, Junction-to-Case www.irf.com 5 IRLR/U7821PbF 15V 1000 ID 4.9A 8.5A 12A TOP + V - DD IAS 800 A 0.01Ω tp Fig 12a. Unclamped Inductive Test Circuit V(BR)DSS tp EAS , Single Pulse Avalanche Energy (mJ) D.U.T RG 20V VGS DRIVER L VDS BOTTOM 600 400 200 0 25 50 75 100 125 150 175 ( ° C) Starting Tj, Junction Temperature Fig 12c. Maximum Avalanche Energy Vs. Drain Current I AS VDS Fig 12b. Unclamped Inductive Waveforms VGS RG Current Regulator Same Type as D.U.T. RD D.U.T. + -V DD V GS Pulse Width ≤ 1 µs Duty Factor ≤ 0.1 % 50KΩ 12V Fig 14a. Switching Time Test Circuit .2µF .3µF D.U.T. + V - DS VDS 90% VGS 3mA IG ID Current Sampling Resistors Fig 13. Gate Charge Test Circuit 6 10% VGS td(on) tr t d(off) tf Fig 14b. Switching Time Waveforms www.irf.com IRLR/U7821PbF D.U.T Driver Gate Drive + - * D.U.T. ISD Waveform Reverse Recovery Current + RG • • • • dv/dt controlled by R G Driver same type as D.U.T. I SD controlled by Duty Factor "D" D.U.T. - Device Under Test V DD P.W. Period VGS=10V Circuit Layout Considerations • Low Stray Inductance • Ground Plane • Low Leakage Inductance Current Transformer - D= Period P.W. + + Body Diode Forward Current di/dt D.U.T. VDS Waveform Diode Recovery dv/dt Re-Applied Voltage - Body Diode VDD Forward Drop Inductor Curent ISD Ripple ≤ 5% * VGS = 5V for Logic Level Devices Fig 15. Peak Diode Recovery dv/dt Test Circuit for N-Channel HEXFET® Power MOSFETs Id Vds Vgs Vgs(th) Qgs1 Qgs2 Qgd Qgodr Fig 16. Gate Charge Waveform www.irf.com 7 IRLR/U7821PbF Power MOSFET Selection for Non-Isolated DC/DC Converters Control FET Synchronous FET Special attention has been given to the power losses in the switching elements of the circuit - Q1 and Q2. Power losses in the high side switch Q1, also called the Control FET, are impacted by the Rds(on) of the MOSFET, but these conduction losses are only about one half of the total losses. The power loss equation for Q2 is approximated by; * Ploss = Pconduction + Pdrive + Poutput ( 2 Ploss = Irms × Rds(on) ) Power losses in the control switch Q1 are given by; + (Qg × Vg × f ) Ploss = Pconduction+ Pswitching+ Pdrive+ Poutput ⎛Q ⎞ + ⎜ oss × Vin × f + (Qrr × Vin × f ) ⎝ 2 ⎠ This can be expanded and approximated by; *dissipated primarily in Q1. Ploss = (Irms 2 × Rds(on ) ) ⎛ Qgd +⎜I × × Vin × ig ⎝ ⎞ ⎛ Qgs 2 ⎞ f⎟ + ⎜ I × × Vin × f ⎟ ig ⎠ ⎝ ⎠ + (Qg × Vg × f ) + ⎛ Qoss × Vin × f ⎞ ⎝ 2 ⎠ This simplified loss equation includes the terms Qgs2 and Qoss which are new to Power MOSFET data sheets. Qgs2 is a sub element of traditional gate-source charge that is included in all MOSFET data sheets. The importance of splitting this gate-source charge into two sub elements, Qgs1 and Qgs2, can be seen from Fig 16. Qgs2 indicates the charge that must be supplied by the gate driver between the time that the threshold voltage has been reached and the time the drain current rises to Idmax at which time the drain voltage begins to change. Minimizing Q gs2 is a critical factor in reducing switching losses in Q1. Qoss is the charge that must be supplied to the output capacitance of the MOSFET during every switching cycle. Figure A shows how Qoss is formed by the parallel combination of the voltage dependant (nonlinear) capacitances Cds and Cdg when multiplied by the power supply input buss voltage. For the synchronous MOSFET Q2, Rds(on) is an important characteristic; however, once again the importance of gate charge must not be overlooked since it impacts three critical areas. Under light load the MOSFET must still be turned on and off by the control IC so the gate drive losses become much more significant. Secondly, the output charge Qoss and reverse recovery charge Qrr both generate losses that are transfered to Q1 and increase the dissipation in that device. Thirdly, gate charge will impact the MOSFETs’ susceptibility to Cdv/dt turn on. The drain of Q2 is connected to the switching node of the converter and therefore sees transitions between ground and Vin. As Q1 turns on and off there is a rate of change of drain voltage dV/dt which is capacitively coupled to the gate of Q2 and can induce a voltage spike on the gate that is sufficient to turn the MOSFET on, resulting in shoot-through current . The ratio of Qgd/Qgs1 must be minimized to reduce the potential for Cdv/dt turn on. Figure A: Qoss Characteristic 8 www.irf.com IRLR/U7821PbF D-Pak (TO-252AA) Package Outline D-Pak (TO-252AA) Part Marking Information EXAMPL E: T HIS IS AN IRF R120 WIT H AS S EMBLY LOT CODE 1234 AS S EMB LED ON WW 16, 2001 IN T HE AS S EMBLY LINE "A" PART NUMBER INT ERNAT IONAL RECT IFIER LOGO Note: "P" in as s embly line pos ition indicates "Lead-Free" IRFR120 12 116A 34 AS S EMBL Y LOT CODE DAT E CODE YEAR 1 = 2001 WEEK 16 L INE A OR INT ERNAT IONAL RECT IF IER L OGO PART NUMBER IRF R120 12 AS S EMBLY L OT CODE www.irf.com 34 DAT E CODE P = DES IGNAT ES LEAD-F REE PRODUCT (OPT IONAL) YEAR 1 = 2001 WEEK 16 A = AS S EMBL Y S IT E CODE 9 IRLR/U7821PbF I-Pak (TO-251AA) Package Outline Dimensions are shown in millimeters (inches) I-Pak (TO-251AA) Part Marking Information EXAMPLE: THIS IS AN IRFU120 WIT H AS SEMBLY LOT CODE 5678 AS S EMBLED ON WW 19, 2001 IN THE AS S EMBLY LINE "A" INTERNATIONAL RECTIFIER LOGO PART NUMBER IRFU120 119A 56 78 AS S EMBLY LOT CODE Note: "P" in ass embly line position indicates Lead-Free" DATE CODE YEAR 1 = 2001 WEEK 19 LINE A OR INTERNATIONAL RECTIFIER LOGO PART NUMBER IRFU120 56 AS S EMBLY LOT CODE 10 78 DATE CODE P = DESIGNATES LEAD-FREE PRODUCT (OPTIONAL) YEAR 1 = 2001 WEEK 19 A = AS S EMBLY S ITE CODE www.irf.com IRLR/U7821PbF D-Pak (TO-252AA) Tape & Reel Information Dimensions are shown in millimeters (inches) TR TRR 16.3 ( .641 ) 15.7 ( .619 ) 12.1 ( .476 ) 11.9 ( .469 ) FEED DIRECTION TRL 16.3 ( .641 ) 15.7 ( .619 ) 8.1 ( .318 ) 7.9 ( .312 ) FEED DIRECTION NOTES : 1. CONTROLLING DIMENSION : MILLIMETER. 2. ALL DIMENSIONS ARE SHOWN IN MILLIMETERS ( INCHES ). 3. OUTLINE CONFORMS TO EIA-481 & EIA-541. 13 INCH 16 mm NOTES : 1. OUTLINE CONFORMS TO EIA-481. Notes: Repetitive rating; pulse width limited by max. junction temperature. Starting TJ = 25°C, L = 3.2mH RG = 25Ω, IAS = 12A. Pulse width ≤ 400µs; duty cycle ≤ 2%. Calculated continuous current based on maximum allowable junction temperature. Package limitation current is 30A. When mounted on 1" square PCB (FR-4 or G-10 Material). For recommended footprint and soldering techniques refer to application note #AN-994. Data and specifications subject to change without notice. This product has been designed and qualified for the Industrial market. Qualification Standards can be found on IR’s Web site. IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105 TAC Fax: (310) 252-7903 Visit us at www.irf.com for sales contact information.10/2006 www.irf.com 11 Note: For the most current drawings please refer to the IR website at: http://www.irf.com/package/