PD - 95661 Applications l High Frequency Synchronous Buck Converters for Computer Processor Power l Lead-Free Benefits l Low RDS(on) at 4.5V VGS l Ultra-Low Gate Impedance l Fully Characterized Avalanche Voltage and Current IRL3714ZPbF IRL3714ZSPbF IRL3714ZLPbF HEXFET® Power MOSFET VDSS RDS(on) max 16m: 20V TO-220AB IRL3714Z D2Pak IRL3714ZS Qg 4.8nC TO-262 IRL3714ZL Absolute Maximum Ratings Parameter Max. Units 20 V VDS Drain-to-Source Voltage VGS Gate-to-Source Voltage ± 20 ID @ TC = 25°C Continuous Drain Current, VGS @ 10V 36 ID @ TC = 100°C Continuous Drain Current, VGS @ 10V 25 IDM Pulsed Drain Current 140 PD @TC = 25°C Maximum Power Dissipation 35 PD @TC = 100°C Maximum Power Dissipation 18 TJ Linear Derating Factor Operating Junction and TSTG Storage Temperature Range c g g A W 0.23 -55 to + 175 Soldering Temperature, for 10 seconds W/°C °C 300 (1.6mm from case) Thermal Resistance Parameter RθJC Junction-to-Case RθCS Case-to-Sink, Flat Greased Surface RθJA Junction-to-Ambient RθJA Junction-to-Ambient (PCB Mount) e e h Typ. Max. Units ––– 4.3 °C/W 0.50 ––– ––– 62 ––– 40 Notes through are on page 12 www.irf.com 1 7/30/04 IRL3714Z/S/LPbF Static @ TJ = 25°C (unless otherwise specified) Parameter Min. Typ. Max. Units BVDSS Drain-to-Source Breakdown Voltage ∆ΒVDSS/∆TJ RDS(on) V Conditions 20 ––– ––– VGS = 0V, ID = 250µA Breakdown Voltage Temp. Coefficient ––– 0.015 ––– Static Drain-to-Source On-Resistance ––– 13 16 mV/°C Reference to 25°C, ID = 1mA mΩ VGS = 10V, ID = 15A ––– 21 26 VGS = 4.5V, ID = 12A VGS(th) Gate Threshold Voltage 1.65 2.1 2.55 V ∆VGS(th)/∆TJ Gate Threshold Voltage Coefficient ––– -5.2 ––– mV/°C IDSS Drain-to-Source Leakage Current ––– ––– 1.0 µA VDS = 16V, VGS = 0V ––– ––– 150 Gate-to-Source Forward Leakage ––– ––– 100 nA VGS = 20V Gate-to-Source Reverse Leakage ––– ––– -100 21 ––– ––– ––– 4.8 7.2 IGSS gfs Qg Forward Transconductance Total Gate Charge e e VDS = VGS, ID = 250µA VDS = 16V, VGS = 0V, TJ = 125°C VGS = -20V S VDS = 10V, ID = 14A Qgs1 Pre-Vth Gate-to-Source Charge ––– 1.7 ––– Qgs2 Post-Vth Gate-to-Source Charge ––– 0.80 ––– Qgd Gate-to-Drain Charge ––– 1.7 ––– ID = 14A Qgodr ––– 0.60 ––– See Fig. 16 Qsw Gate Charge Overdrive Switch Charge (Qgs2 + Qgd) ––– 2.5 ––– Qoss Output Charge ––– 2.7 ––– td(on) Turn-On Delay Time ––– 6.0 ––– tr Rise Time ––– 13 ––– td(off) Turn-Off Delay Time ––– 10 ––– tf Fall Time ––– 5.0 ––– Ciss Input Capacitance ––– 550 ––– Coss Output Capacitance ––– 180 ––– Crss Reverse Transfer Capacitance ––– 99 ––– VDS = 10V nC nC VGS = 4.5V VDS = 10V, VGS = 0V VDD = 10V, VGS = 4.5V e ID = 14A ns Clamped Inductive Load pF VDS = 10V VGS = 0V ƒ = 1.0MHz Avalanche Characteristics EAS Parameter Single Pulse Avalanche Energy IAR Avalanche Current EAR Repetitive Avalanche Energy c d c Typ. ––– Max. 23 Units mJ ––– 14 A ––– 3.5 mJ Diode Characteristics Parameter Min. Typ. Max. Units g Conditions IS Continuous Source Current ––– ––– 36 ISM (Body Diode) Pulsed Source Current ––– ––– 140 showing the integral reverse VSD (Body Diode) Diode Forward Voltage ––– ––– 1.0 V p-n junction diode. TJ = 25°C, IS = 14A, VGS = 0V trr Reverse Recovery Time ––– 8.3 12 ns Qrr Reverse Recovery Charge ––– 1.5 2.3 nC 2 c MOSFET symbol A D G S e TJ = 25°C, IF = 14A, VDD = 10V di/dt = 100A/µs e www.irf.com IRL3714Z/S/LPbF 1000 1000 BOTTOM 100 TOP ID, Drain-to-Source Current (A) ID, Drain-to-Source Current (A) TOP VGS 10V 9.0V 7.0V 5.0V 4.5V 4.0V 3.5V 3.0V 10 3.0V 30µs PULSE WIDTH Tj = 25°C 1 0.1 1 10 3.0V 30µs PULSE WIDTH Tj = 175°C 1 10 0.1 V DS, Drain-to-Source Voltage (V) 1 10 V DS, Drain-to-Source Voltage (V) Fig 1. Typical Output Characteristics Fig 2. Typical Output Characteristics 1000 2.0 RDS(on) , Drain-to-Source On Resistance (Normalized) ID, Drain-to-Source Current (Α) BOTTOM 100 VGS 10V 9.0V 7.0V 5.0V 4.5V 4.0V 3.5V 3.0V TJ = 25°C 100 T J = 175°C 10 VDS = 10V 30µs PULSE WIDTH 1.0 ID = 36A VGS = 10V 1.5 1.0 0.5 2 3 4 5 6 7 8 9 VGS, Gate-to-Source Voltage (V) Fig 3. Typical Transfer Characteristics www.irf.com 10 -60 -40 -20 0 20 40 60 80 100 120 140 160 180 T J , Junction Temperature (°C) Fig 4. Normalized On-Resistance vs. Temperature 3 IRL3714Z/S/LPbF 10000 6.0 VGS = 0V, f = 1 MHZ C iss = C gs + C gd, C ds SHORTED C rss = C gd VGS, Gate-to-Source Voltage (V) ID= 14A C, Capacitance(pF) C oss = C ds + C gd 1000 Ciss Coss Crss 100 VDS= 16V VDS= 10V 5.0 4.0 3.0 2.0 1.0 0.0 10 1 10 100 0 3 4 5 6 7 1000 ID, Drain-to-Source Current (A) 1000.00 ISD, Reverse Drain Current (A) 2 Fig 6. Typical Gate Charge vs. Gate-to-Source Voltage Fig 5. Typical Capacitance vs. Drain-to-Source Voltage 100.00 OPERATION IN THIS AREA LIMITED BY R DS(on) 100 T J = 175°C 10.00 T J = 25°C 100µsec 10 Tc = 25°C Tj = 175°C Single Pulse VGS = 0V 1.00 1msec 10msec 1 0.0 0.5 1.0 1.5 2.0 VSD, Source-to-Drain Voltage (V) Fig 7. Typical Source-Drain Diode Forward Voltage 4 1 QG Total Gate Charge (nC) VDS, Drain-to-Source Voltage (V) 2.5 0 1 10 100 VDS, Drain-to-Source Voltage (V) Fig 8. Maximum Safe Operating Area www.irf.com IRL3714Z/S/LPbF 40 3.0 VGS(th) Gate threshold Voltage (V) ID, Drain Current (A) 35 30 25 20 15 10 5 2.5 2.0 ID = 250µA 1.5 1.0 0 25 50 75 100 125 150 -75 -50 -25 175 0 25 50 75 100 125 150 175 200 T J , Temperature ( °C ) T C , Case Temperature (°C) Fig 9. Maximum Drain Current vs. Case Temperature Fig 10. Threshold Voltage vs. Temperature Thermal Response ( Z thJC ) 10 D = 0.50 1 0.20 0.10 τJ 0.05 0.02 0.1 R1 R1 τJ τ1 τ1 R2 R2 τ2 τ2 Ci= τi/Ri Ci= τi/Ri 0.01 SINGLE PULSE ( THERMAL RESPONSE ) R3 R3 τ3 τC τ τ3 Ri (°C/W) τi (sec) 1.292 0.000135 2.337 0.000882 0.652 0.005472 Notes: 1. Duty Factor D = t1/t2 2. Peak Tj = P dm x Zthjc + Tc 0.01 1E-006 1E-005 0.0001 0.001 0.01 0.1 t1 , Rectangular Pulse Duration (sec) Fig 11. Maximum Effective Transient Thermal Impedance, Junction-to-Case www.irf.com 5 IRL3714Z/S/LPbF 15V D.U.T RG + V - DD IAS 20V VGS A 0.01Ω tp Fig 12a. Unclamped Inductive Test Circuit V(BR)DSS tp EAS , Single Pulse Avalanche Energy (mJ) DRIVER L VDS 100 ID 3.7A 6.2A BOTTOM 14A TOP 80 60 40 20 0 25 50 75 100 125 150 175 Starting T J , Junction Temperature (°C) Fig 12c. Maximum Avalanche Energy vs. Drain Current LD I AS VDS Fig 12b. Unclamped Inductive Waveforms + VDD D.U.T Current Regulator Same Type as D.U.T. VGS Pulse Width < 1µs Duty Factor < 0.1% 50KΩ 12V .2µF .3µF Fig 14a. Switching Time Test Circuit D.U.T. + V - DS VDS 90% VGS 3mA 10% IG ID Current Sampling Resistors Fig 13. Gate Charge Test Circuit VGS td(on) tr td(off) tf Fig 14b. Switching Time Waveforms 6 www.irf.com IRL3714Z/S/LPbF D.U.T Driver Gate Drive P.W. + + - - * D.U.T. ISD Waveform Reverse Recovery Current + RG • • • • dv/dt controlled by R G Driver same type as D.U.T. I SD controlled by Duty Factor "D" D.U.T. - Device Under Test P.W. Period VGS=10V Circuit Layout Considerations • Low Stray Inductance • Ground Plane • Low Leakage Inductance Current Transformer D= Period V DD + - Body Diode Forward Current di/dt D.U.T. VDS Waveform Diode Recovery dv/dt Re-Applied Voltage Body Diode VDD Forward Drop Inductor Curent ISD Ripple ≤ 5% * VGS = 5V for Logic Level Devices Fig 15. Peak Diode Recovery dv/dt Test Circuit for N-Channel HEXFET® Power MOSFETs Id Vds Vgs Vgs(th) Qgs1 Qgs2 Qgd Qgodr Fig 16. Gate Charge Waveform www.irf.com 7 IRL3714Z/S/LPbF Power MOSFET Selection for Non-Isolated DC/DC Converters Control FET Synchronous FET Special attention has been given to the power losses in the switching elements of the circuit - Q1 and Q2. Power losses in the high side switch Q1, also called the Control FET, are impacted by the Rds(on) of the MOSFET, but these conduction losses are only about one half of the total losses. The power loss equation for Q2 is approximated by; * Ploss = Pconduction + Pdrive + Poutput ( 2 Ploss = Irms × Rds(on) ) Power losses in the control switch Q1 are given by; + (Qg × Vg × f ) Ploss = Pconduction+ Pswitching+ Pdrive+ Poutput ⎛Q ⎞ + ⎜ oss × Vin × f + (Qrr × Vin × f ) ⎝ 2 ⎠ This can be expanded and approximated by; *dissipated primarily in Q1. Ploss = (Irms 2 × Rds(on ) ) ⎛ Qgd +⎜I × × Vin × ig ⎝ ⎞ ⎞ ⎛ Qgs 2 f⎟ + ⎜ I × × Vin × f ⎟ ig ⎠ ⎝ ⎠ + (Qg × Vg × f ) + ⎛ Qoss × Vin × f ⎞ ⎝ 2 ⎠ This simplified loss equation includes the terms Qgs2 and Qoss which are new to Power MOSFET data sheets. Qgs2 is a sub element of traditional gate-source charge that is included in all MOSFET data sheets. The importance of splitting this gate-source charge into two sub elements, Qgs1 and Qgs2, can be seen from Fig 16. Qgs2 indicates the charge that must be supplied by the gate driver between the time that the threshold voltage has been reached and the time the drain current rises to Idmax at which time the drain voltage begins to change. Minimizing Q gs2 is a critical factor in reducing switching losses in Q1. Qoss is the charge that must be supplied to the output capacitance of the MOSFET during every switching cycle. Figure A shows how Qoss is formed by the parallel combination of the voltage dependant (nonlinear) capacitances Cds and Cdg when multiplied by the power supply input buss voltage. For the synchronous MOSFET Q2, Rds(on) is an important characteristic; however, once again the importance of gate charge must not be overlooked since it impacts three critical areas. Under light load the MOSFET must still be turned on and off by the control IC so the gate drive losses become much more significant. Secondly, the output charge Qoss and reverse recovery charge Qrr both generate losses that are transfered to Q1 and increase the dissipation in that device. Thirdly, gate charge will impact the MOSFETs’ susceptibility to Cdv/dt turn on. The drain of Q2 is connected to the switching node of the converter and therefore sees transitions between ground and Vin. As Q1 turns on and off there is a rate of change of drain voltage dV/dt which is capacitively coupled to the gate of Q2 and can induce a voltage spike on the gate that is sufficient to turn the MOSFET on, resulting in shoot-through current . The ratio of Qgd/Qgs1 must be minimized to reduce the potential for Cdv/dt turn on. Figure A: Qoss Characteristic 8 www.irf.com IRL3714Z/S/LPbF TO-220AB Package Outline Dimensions are shown in millimeters (inches) 2.87 (.113) 2.62 (.103) 10.54 (.415) 10.29 (.405) -B- 3.78 (.149) 3.54 (.139) 4.69 (.185) 4.20 (.165) -A- 1.32 (.052) 1.22 (.048) 6.47 (.255) 6.10 (.240) 4 15.24 (.600) 14.84 (.584) LEAD ASSIGNMENTS 1.15 (.045) MIN 1 2 LEAD ASSIGNMENTS IGBTs, CoPACK 1 - GATE 2 - DRAIN 1- GATE 1- GATE 3 - SOURCE 2- COLLECTOR 2- DRAIN 3- SOURCE 3- EMITTER 4 - DRAIN HEXFET 3 4- DRAIN 14.09 (.555) 13.47 (.530) 3X 1.40 (.055) 3X 1.15 (.045) 4- COLLECTOR 4.06 (.160) 3.55 (.140) 0.93 (.037) 0.69 (.027) 0.36 (.014) 3X M B A M 0.55 (.022) 0.46 (.018) 2.92 (.115) 2.64 (.104) 2.54 (.100) 2X NOTES: 1 DIMENSIONING & TOLERANCING PER ANSI Y14.5M, 1982. 3 OUTLINE CONFORMS TO JEDEC OUTLINE TO-220AB. 2 CONTROLLING DIMENSION : INCH 4 HEATSINK & LEAD MEASUREMENTS DO NOT INCLUDE BURRS. TO-220AB Part Marking Information E XAMP L E : T HIS IS AN IR F 1010 L OT CODE 1789 AS S E MB L E D ON WW 19, 1997 IN T H E AS S E MB L Y L INE "C" Note: "P" in assembly line position indicates "Lead-Free" INT E R NAT IONAL R E CT IF IE R L OGO AS S E MB L Y L OT CODE www.irf.com P AR T NU MB E R DAT E CODE YE AR 7 = 1997 WE E K 19 L INE C 9 IRL3714Z/S/LPbF D2Pak Package Outline Dimensions are shown in millimeters (inches) D2Pak Part Marking Information T HIS IS AN IRF 530S WITH LOT CODE 8024 ASSE MBLE D ON WW 02, 2000 IN THE AS SE MB LY LINE "L" INT E RNAT IONAL RECT IF IE R LOGO Note: "P" in as s embly line pos ition indicates "Lead-F ree" AS SE MBLY LOT CODE OR INT ERNATIONAL RECT IFIER LOGO AS S EMBLY LOT CODE 10 PART NUMB ER F530S DAT E CODE YEAR 0 = 2000 WEE K 02 LINE L PART NUMBER F 530S DAT E CODE P = DES IGNAT ES LEAD-FREE PRODUCT (OPTIONAL) YEAR 0 = 2000 WEEK 02 A = AS S EMBLY S IT E CODE www.irf.com IRL3714Z/S/LPbF TO-262 Package Outline Dimensions are shown in millimeters (inches) TO-262 Part Marking Information EXAMPLE: T HIS IS AN IRL3103L LOT CODE 1789 AS S EMBLE D ON WW 19, 1997 IN THE AS S E MBLY LINE "C" Note: "P" in as sembly line position indicates "Lead-Free" INTERNATIONAL RECT IF IE R LOGO AS S EMBLY LOT CODE PART NUMBER DAT E CODE YEAR 7 = 1997 WEEK 19 LINE C OR INTERNATIONAL RECT IF IE R LOGO AS S EMBLY LOT CODE www.irf.com PART NUMBER DAT E CODE P = DES IGNAT ES LE AD-FREE PRODUCT (OPTIONAL) YE AR 7 = 1997 WE EK 19 A = AS S E MBLY S IT E CODE 11 IRL3714Z/S/LPbF D2Pak Tape & Reel Information Dimensions are shown in millimeters (inches) TRR 1.60 (.063) 1.50 (.059) 1.60 (.063) 1.50 (.059) 4.10 (.161) 3.90 (.153) FEED DIRECTION 1.85 (.073) 11.60 (.457) 11.40 (.449) 1.65 (.065) 0.368 (.0145) 0.342 (.0135) 15.42 (.609) 15.22 (.601) 24.30 (.957) 23.90 (.941) TRL 1.75 (.069) 1.25 (.049) 10.90 (.429) 10.70 (.421) 4.72 (.136) 4.52 (.178) 16.10 (.634) 15.90 (.626) FEED DIRECTION 13.50 (.532) 12.80 (.504) 27.40 (1.079) 23.90 (.941) 4 330.00 (14.173) MAX. 60.00 (2.362) MIN. NOTES : 1. COMFORMS TO EIA-418. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION MEASURED @ HUB. 4. INCLUDES FLANGE DISTORTION @ OUTER EDGE. Notes: Repetitive rating; pulse width limited by max. junction temperature. Starting TJ = 25°C, L = 0.22mH, RG = 25Ω, IAS = 14A. Pulse width ≤ 400µs; duty cycle ≤ 2%. 30.40 (1.197) MAX. 26.40 (1.039) 24.40 (.961) 3 4 Coss eff. is a fixed capacitance that gives the same charging time as Coss while VDS is rising from 0 to 80% VDSS. This is only applied to TO-220AB pakcage. This is applied to D2Pak, when mounted on 1" square PCB (FR4 or G-10 Material). For recommended footprint and soldering techniques refer to application note #AN-994. TO-220AB package is not recommended for Surface Mount Application. Data and specifications subject to change without notice. This product has been designed and qualified for the Industrial market. Qualification Standards can be found on IR’s Web site. IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105 TAC Fax: (310) 252-7903 Visit us at www.irf.com for sales contact information. 07/04 12 www.irf.com Note: For the most current drawings please refer to the IR website at: http://www.irf.com/package/