Previous Datasheet Index Next Data Sheet DISCRETE POWER DIODES and THYRISTORS DATA BOOK D-294 To Order Previous Datasheet Index Next Data Sheet Bulletin I25159/B ST280C..C SERIES PHASE CONTROL THYRISTORS Hockey Puk Version Features 500A Center amplifying gate Metal case with ceramic insulator International standard case TO-200AB (A-PUK) Typical Applications DC motor controls Controlled DC power supplies AC controllers case style TO-200AB (A-PUK) Major Ratings and Characteristics Parameters ST280C..C Units 500 A 55 °C 960 A 25 °C @ 50Hz 7850 A @ 60Hz 8220 A @ 50Hz 308 KA2s @ 60Hz 281 KA2s IT(AV) @ Ths IT(RMS) @ Ths ITSM 2 I t V DRM /V RRM tq TJ typical 400 to 600 V 100 µs - 40 to 125 °C D-295 To Order Previous Datasheet Index Next Data Sheet ST280C..C Series ELECTRICAL SPECIFICATIONS Voltage Ratings Voltage V DRM /V RRM , max. repetitive VRSM , maximum non- I DRM /I RRM max. Code peak and off-state voltage repetitive peak voltage @ TJ = TJ max V V mA 04 400 500 06 600 700 Type number ST280C..C 30 On-state Conduction Parameter I T(AV) Max. average on-state current @ Heatsink temperature ST280C..C Units Conditions 500 (185) A 180° conduction, half sine wave 55 (85) °C double side (single side) cooled I T(RMS) Max. RMS on-state current 960 DC @ 25°C heatsink temperature double side cooled I TSM Max. peak, one-cycle 7850 t = 10ms non-repetitive surge current 8220 12 A 6600 I2 t Maximum I2t for fusing Maximum I2√t for fusing V T(TO) 1 Low level value of threshold Low level value of on-state t = 8.3ms reapplied Sinusoidal half wave, No voltage Initial TJ = TJ max. t = 8.3ms reapplied KA2s 218 t = 10ms 100% VRRM 200 t = 8.3ms reapplied KA2√s 3080 High level value of on-state slope resistance t = 0.1 to 10ms, no voltage reapplied (16.7% x π x IT(AV) < I < π x IT(AV)), TJ = TJ max. 0.84 V (I > π x IT(AV)),TJ = TJ max. 0.88 (16.7% x π x IT(AV) < I < π x IT(AV)), TJ = TJ max. 0.50 slope resistance rt2 100% VRRM t = 10ms voltage rt1 reapplied t = 10ms 308 voltage V T(TO) 2 High level value of threshold t = 8.3ms 6900 281 I 2 √t No voltage mΩ (I > π x IT(AV)),TJ = TJ max. 0.47 V TM Max. on-state voltage 1.36 IH Maximum holding current 600 IL Max. (typical) latching current V 2222222222222 I = 1050A, TJ = 125°C, t = 10ms sine pulse mA T J = 25°C, anode supply 12V resistive load 1000 (300) pk p Switching Parameter di/dt Max. non-repetitive rate of rise of turned-on current t d Typical delay time ST280C..C 1000 Units Conditions A/µs q Typical turn-off time r TJ = TJ max, anode voltage ≤ 80% VDRM Gate current 1A, di /dt = 1A/µs g 1.0 µs t Gate drive 20V, 20Ω, t ≤ 1µs 100 V = 0.67% VDRM, TJ = 25°C d ITM = 300A, TJ = TJ max, di/dt = 20A/µs, VR = 50V dv/dt = 20V/µs, Gate 0V 100Ω, t = 500µs p D-296 To Order Previous Datasheet Index Next Data Sheet ST280C..C Series Fig. 3 - Current Ratings Characteristics Fig. 4 - Current Ratings Characteristics Fig. 6- On-state Power Loss Characteristics Fig. 5- On-state Power Loss Characteristics Fig. 7 - Maximum Non-Repetitive Surge Current Single and Double Side Cooled Fig. 8 - Maximum Non-Repetitive Surge Current Single and Double Side Cooled D-300 To Order Previous Datasheet Index Next Data Sheet ST280C..C Series Fig. 9 - On-state Voltage Drop Characteristics Fig. 10 - Thermal Impedance Z thJ-hs Characteristics Fig. 11 - Gate Characteristics D-301 To Order Previous Datasheet Index Next Data Sheet ST280C..C Series Blocking Parameter ST280C..C Units Conditions dv/dt Maximum critical rate of rise of off-state voltage 500 V/µs TJ = TJ max. linear to 80% rated VDRM IDRM IRRM Max. peak reverse and off-state leakage current 30 mA TJ = TJ max, rated V DRM/V RRM applied Triggering Parameter PGM ST280C..C Maximum peak gate power 10.0 PG(AV) Maximum average gate power 2.0 IGM Max. peak positive gate current 3.0 +VGM Maximum peak positive Maximum peak negative VGT VGD TJ = TJ max, t ≤ 5ms V TJ = TJ max, t ≤ 5ms DC gate voltage required 180 - 90 150 40 - 2.9 - 1.8 3.0 1.2 - DC gate current not to trigger DC gate voltage not to trigger p p MAX. TJ = - 40°C DC gate current required to trigger IGD A 23 TYP. to trigger TJ = TJ max, t p ≤ 5ms TJ = TJ max, f = 50Hz, d% = 50 5.0 gate voltage IGT W 20 gate voltage -VGM Units Conditions 10 mA TJ = 25°C TJ = 125°C TJ = - 40°C V TJ = 25°C TJ = 125°C mA 0.30 Max. required gate trigger/ current/ voltage are the lowest value which will trigger all units 12V anode-to-cathode applied V TJ = TJ max Max. gate current/voltage not to trigger is the max. value which will not trigger any unit with rated VDRM anode-to-cathode applied Thermal and Mechanical Specification Parameter ST280C..C TJ Max. operating temperature range -40 to 125 T Max. storage temperature range -40 to 150 stg RthJ-hs Max. thermal resistance, junction to heatsink RthC-hs Max. thermal resistance, Units °C 0.17 DC operation single side cooled K/W 0.08 0.033 K/W case to heatsink 0.017 F Mounting force, ± 10% 4900 N (500) (Kg) wt Approximate weight 50 g Case style Conditions DC operation double side cooled DC operation single side cooled DC operation double side cooled TO - 200AB (A-PUK) See Outline Table D-297 3333 To Order Previous Datasheet Index Next Data Sheet ST280C..C Series ∆RthJ-hs Conduction (The following table shows the increment of thermal resistence RthJ-hs when devices operate at different conduction angles than DC) Conduction angle Sinusoidal conduction Rectangular conduction Single Side Double Side Single Side Double Side 180° 0.016 0.016 0.011 0.011 120° 0.019 0.019 0.019 0.019 90° 0.024 0.024 0.026 0.026 60° 0.035 0.035 0.036 0.037 30° 0.060 0.060 0.060 0.061 Units Conditions TJ = TJ max. K/W 12 Ordering Information Table Device Code ST 28 0 C 06 C 1 1 2 3 4 5 6 7 8 1 - Thyristor 2 - Essential part number 3 - 0 = Converter grade 4 - C = Ceramic Puk 5 - Voltage code: Code x 100 = VRRM (See Voltage Rating Table) 6 - C = Puk Case TO-200AB (A-PUK) 7 - 0 = Eyelet terminals (Gate and Auxiliary Cathode Unsoldered Leads) 1 = Fast-on terminals (Gate and Auxiliary Cathode Unsoldered Leads) 2 = Eyelet terminals (Gate and Auxiliary Cathode Soldered Leads) 3 = Fast-on terminals (Gate and Auxiliary Cathode Soldered Leads) 8 - Critical dv/dt: None = 500V/µsec (Standard selection) L = 1000V/µsec (Special selection) D-298 To Order 2222222222222 Previous Datasheet Index Next Data Sheet ST280C..C Series Outline Table ANODE TO GATE CREEPAGE DISTANCE: 7.62 (0.30) MIN. STRIKE DISTANCE: 7.12 (0.28) MIN. 19 (0.75) 0.3 (0.01) MIN. DIA. MAX. 13.7 / 14.4 (0.54 / 0.57) 0.3 (0.01) MIN. 19 (0.75) GATE TERM. FOR 1.47 (0.06) DIA. PIN RECEPTACLE DIA. MAX. 38 (1.50) DIA MAX. Case Style TO-200AB (A-PUK) 2 HOLES 3.56 (0.14) x 1.83 (0.07) MIN. DEEP All dimensions in millimeters (inches) 6.5 (0.26) 4.75 (0.19) 23 25°± 5° 42 (1.65) MAX. 28 (1.10) Fig. 1 - Current Ratings Characteristics Fig. 2 - Current Ratings Characteristics D-299 3333 To Order