Data Sheet No. PD60338 IRMCK312 Dual Channel Sensorless Motor Control IC for Appliances Features Product Summary Maximum crystal frequency TM MCE (Motion Control Engine) - Hardware based computation engine for high efficiency sinusoidal sensorless control of permanent magnet AC motor Integrated Power Factor Correction control Supports both interior and surface permanent magnet motors Built-in hardware peripheral for single shunt current feedback reconstruction No external current or voltage sensing operational amplifier required Dual channel three/two-phase Space Vector PWM Three-channel analog output (PWM) Embedded 8-bit high speed microcontroller (8051) for flexible I/O and man-machine control JTAG programming port for emulation/debugger Two serial communication interface (UART) I2C/SPI serial interface Watchdog timer with independent analog clock Three general purpose timers/counters Two special timers: periodic timer, capture timer Internal ‘One-Time Programmable’ (OTP) memory and internal RAM for final production usage 60 MHz Maximum internal clock (SYSCLK) frequency 128 MHz Maximum 8051 clock frequency 33 MHz Sensorless control computation time TM MCE computation data range 11 μsec typ 16 bit signed 8051 OTP Program memory 56K bytes MCE program and Data RAM 8K bytes GateKill latency (digital filtered) 2 μsec PWM carrier frequency counter 16 bits/ SYSCLK A/D input channels 11 A/D converter resolution 12 bits A/D converter conversion speed 2 μsec 8051 instruction execution speed Analog output (PWM) resolution UART baud rate (typ) Number of I/O (max) Package (lead-free) Operating temperature 2 SYSCLK 8 bits 57.6K bps 36 QFP100 -40°C ~ 85°C Pin compatible with IRMCF312 RAM version 1.8V/3.3V CMOS Description IRMCK312 is a high performance OTP based motion control IC designed primarily for appliance applications. IRMCK312 is designed to achieve low cost and high performance control solutions for advanced inverterized appliance motor control. IRMCK312 contains two computation engines. One is Motion Control Engine (MCETM) for sensorless control of permanent magnet motors; the other is an 8-bit high-speed microcontroller (8051). Both computation engines are integrated into one monolithic chip. The MCETM contains a collection of control elements such as Proportional plus Integral, Vector rotator, Angle estimator, Multiply/Divide, Low loss SVPWM, Single Shunt IFB. The user can program a motion control algorithm by connecting these control elements using a graphic compiler. Key components of the sensorless control algorithms, such as the Angle Estimator, are provided as complete pre-defined control blocks implemented in hardware. A unique analog/digital circuit and algorithm to fully support single shunt current reconstruction is also provided. The 8051 microcontroller performs 2cycle instruction execution (16MIPS at 33MHz). The MCE and 8051 microcontroller are connected via dual port RAM to process signal monitoring and command input. An advanced graphic compiler for the MCETM is seamlessly integrated into the MATLAB/Simulink environment, while third party JTAG based emulator tools are supported for 8051 developments. IRMCK312 comes with a small QFP100 pin lead-free package. Rev 1.0 IRMCK312 TABLE OF CONTENTS 1 2 3 4 Overview...................................................................................................................................... 5 IRMCK312 Block Diagram and Main Functions........................................................................ 6 Pinout........................................................................................................................................... 8 Input/Output of IRMCK312 ........................................................................................................ 9 4.1 8051 Peripheral Interface Group......................................................................................... 10 4.2 Motion Peripheral Interface Group ..................................................................................... 11 4.3 Analog Interface Group ...................................................................................................... 11 4.4 Power Interface Group ........................................................................................................ 12 4.5 Test Interface....................................................................................................................... 12 5 Application Connections ........................................................................................................... 13 6 DC Characteristics ..................................................................................................................... 14 6.1 Absolute Maximum Ratings ............................................................................................... 14 6.2 System Clock Frequency and Power Consumption............................................................ 14 6.3 Digital I/O DC Characteristics............................................................................................ 15 6.4 PLL and Oscillator DC Characteristics............................................................................... 16 6.5 Analog I/O DC Characteristics ........................................................................................... 16 6.6 Under Voltage Lockout DC Characteristics ....................................................................... 17 6.7 AREF Characteristics.......................................................................................................... 17 7 AC Characteristics ..................................................................................................................... 18 7.1 PLL AC Characteristics ...................................................................................................... 18 7.2 Analog to Digital Converter AC Characteristics ................................................................ 19 7.3 Op Amp AC Characteristics ............................................................................................... 19 7.4 SYNC to SVPWM and A/D Conversion AC Timing......................................................... 20 7.5 GATEKILL to SVPWM AC Timing.................................................................................. 21 7.6 Interrupt AC Timing ........................................................................................................... 21 7.7 I2C AC Timing .................................................................................................................... 22 7.8 SPI AC Timing.................................................................................................................... 23 7.8.1 SPI Write AC timing .................................................................................................... 23 7.8.2 SPI Read AC Timing.................................................................................................... 24 7.9 UART AC Timing .............................................................................................................. 25 7.10 CAPTURE Input AC Timing .......................................................................................... 26 7.11 JTAG AC Timing ............................................................................................................ 27 7.12 OTP Programming Timing .............................................................................................. 28 8 I/O Structure .............................................................................................................................. 29 9 Pin List....................................................................................................................................... 32 10 Package Dimensions............................................................................................................... 36 11 Part Marking Information....................................................................................................... 37 12 Ordering Information ............................................................................................................. 37 www.irf.com 2 © 2007 International Rectifier IRMCK312 TABLE OF FIGURES Figure 1. Typical Application Block Diagram Using IRMCK312 ................................................. 5 Figure 2. IRMCK312 Internal Block Diagram ............................................................................... 6 Figure 3. IRMCK312 Pin Configuration......................................................................................... 8 Figure 4. Input/Output of IRMCK312 ............................................................................................ 9 Figure 5. Application Connection of IRMCK312......................................................................... 13 Figure 6. Clock Frequency vs. Power Consumption..................................................................... 14 Figure 7 Crystal oscillator circuit.................................................................................................. 18 Figure 8 Voltage droop of sample and hold .................................................................................. 19 Figure 9 SYNC to SVPWM and A/D conversion AC Timing...................................................... 20 Figure 10 GATEKILL to SVPWM AC Timing............................................................................... 21 Figure 11 Interrupt AC Timing ..................................................................................................... 21 Figure 12 I2C AC Timing.............................................................................................................. 22 Figure 13 SPI AC Timing ............................................................................................................. 23 Figure 14 SPI Read AC Timing .................................................................................................... 24 Figure 15 UART AC Timing ........................................................................................................ 25 Figure 16 CAPTURE Input AC Timing........................................................................................ 26 Figure 17 JTAG AC Timing ......................................................................................................... 27 Figure 18 OTP Programming Timing ........................................................................................... 28 Figure 19 All digital I/O except motor PWM output ....................................................................... 29 Figure 20 RESET, GATEKILL I/O ................................................................................................. 29 Figure 21 Analog input..................................................................................................................... 30 Figure 22 Analog operational amplifier output and AREF I/O structure ..................................... 30 Figure 23 VPP programming pin I/O structure .................................................................... 30 Figure 24 VSS and AVSS pin structure ........................................................................................... 31 Figure 25 VDD1 and VDDCAP pin structure.................................................................................. 31 Figure 26 XTAL0/XTAL1 pins structure ..................................................................................... 31 www.irf.com 3 © 2007 International Rectifier IRMCK312 TABLE OF TABLES Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. Table 7. Table 8. Table 9. Table 10. Table 11. Table 12. Table 13. Table 14. Table 15. Table 16. Table 17. Table 18. Table 19. Table 20. Table 21. www.irf.com Absolute Maximum Ratings............................................................................................ 14 System Clock Frequency................................................................................................. 14 Digital I/O DC Characteristics ........................................................................................ 15 PLL DC Characteristics .................................................................................................. 16 Analog I/O DC Characteristics ....................................................................................... 16 UVcc DC Characteristics ................................................................................................ 17 AREF DC Characteristics ............................................................................................... 17 PLL AC Characteristics .................................................................................................. 18 A/D Converter AC Characteristics.................................................................................. 19 Current Sensing OP Amp AC Characteristics............................................................... 19 SYNC AC Characteristics............................................................................................. 20 GATEKILL to SVPWM AC Timing ............................................................................ 21 Interrupt AC Timing...................................................................................................... 21 I2C AC Timing .............................................................................................................. 22 SPI Write AC Timing.................................................................................................... 23 SPI Read AC Timing..................................................................................................... 24 UART AC Timing......................................................................................................... 25 CAPTURE AC Timing ................................................................................................. 26 JTAG AC Timing.......................................................................................................... 27 OTP Programming Timing............................................................................................ 28 Pin List .......................................................................................................................... 35 4 © 2007 International Rectifier IRMCK312 1 Overview IRMCK312 is a new International Rectifier integrated circuit device primarily designed as a onechip solution for complete inverter controlled appliance dual motor control applications. Unlike a traditional microcontroller or DSP, the IRMCK312 provides a built-in closed loop sensorless control algorithm using the unique Motion Control Engine (MCETM) for permanent magnet motors. The MCETM consists of a collection of control elements, motion peripherals, a dedicated motion control sequencer and dual port RAM to map internal signal nodes. IRMCK312 also employs a unique single shunt current reconstruction circuit to eliminate additional analog/digital circuitry and enables a direct shunt resistor interface to the IC. The sensorless control is the same for both motors with a single shunt current sensing capability. Motion control programming is achieved using a dedicated graphical compiler integrated into the MATLAB/SimulinkTM development environment. Sequencing, user interface, host communication, and upper layer control tasks can be implemented in the 8051 high-speed 8-bit microcontroller. The 8051 microcontroller is equipped with a JTAG port to facilitate emulation and debugging tools. Figure 1 shows a typical application schematic using IRMCK312. IRMCK312 is intended for volume production purpose and contains 64K bytes of OTP (One Time Programming) ROM, which can be programmed through a JTAG port. For a development purpose use, IRMCF312 contains a 48k byte of RAM in place of program OTP to facilitate an application development work. Both IRMCF312 and IRMCK312 come in the same 100-pin QFP package with identical pin configuration to facilitate PC board layout and transition to mass production Figure 1. Typical Application Block Diagram Using IRMCK312 www.irf.com 5 © 2007 International Rectifier IRMCK312 2 IRMCK312 Block Diagram and Main Functions IRMCK312 block diagram is shown in Figure 2. Figure 2. IRMCK312 Internal Block Diagram IRMCK312 contains the following functions for sensorless AC motor control applications: • www.irf.com Motion Control Engine (MCETM) o Proportional plus Integral block o Low pass filter o Differentiator and lag (high pass filter) o Ramp o Limit o Angle estimate (sensorless control) o Inverse Clark transformation o Vector rotator o Bit latch o Peak detect o Transition o Multiply-divide (signed and unsigned) o Divide (signed and unsigned) 6 © 2007 International Rectifier IRMCK312 o o o o o o o o o o o o • Adder Subtractor Comparator Counter Accumulator Switch Shift ATAN (arc tangent) Function block (any curve fitting, nonlinear function) 16-bit wide Logic operations (AND, OR, XOR, NOT, NEGATE) MCETM program and data memory (6K byte). Note 1 MCETM control sequencer 8051 microcontroller o Three 16-bit timer/counters o 16-bit periodic timer o 16-bit analog watchdog timer o 16-bit capture timer o Up to 36 discrete I/Os o Eleven-channel 12-bit A/D Five buffered channels (0 – 1.2V input) Six unbuffered channels (0 – 1.2V input) o JTAG port (4 pins) o Up to three channels of analog output (8-bit PWM) o Two UART o I2C/SPI port o 64K byte Note 1program One-Time Programmable memory o 2K byte data RAM. Note 2 Note 1: Total size of OTP memory is 64K byte, however MCE program occupies maximum 8K byte which will be loaded into internal RAM at a powerup/boot process. Therefore only 56K byte OTP memory area is usable for 8051 microcontroller. Note 2: Total size of RAM is 8K byte including MCE program, MCE data, and 8051 data. Different sizes can be allocated depending on applications. www.irf.com 7 © 2007 International Rectifier IRMCK312 P5.0/PFCGKILL PFCPWM P3.1/AOPWM2 P3.3/INT1 P3.2/INT0 P3.4/T0 P3.6/RXD1 P3.5/T1 P3.7/TXD1 VSS VSS VDD1 P4.2/INT5 P4.6/INT9 SCL/SO-SI/VPP SDA/CS0 P5.1/TMS P5.2/TDO P5.3/TDI TCLK NC VDD2 RESET PLLVDD PLLVSS 3 Pinout 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 XTAL0 1 75 P3.0/INT2/CS1 XTAL1 2 74 PWMUH P1.0/T2 3 73 PWMUL P1.1/RXD 4 72 PWMVH P1.2/TXD 5 71 PWMVL P1.3/SYNC/SCK 6 70 PWMWH P1.4/CAP 7 69 PWMWL P1.5 8 68 GATEKILL P1.6 9 67 VDD1 P1.7 10 P4.3/INT6 11 P4.7/INT10 12 VDD2 13 VSS 14 VDD1 FGATEKILL IRMCK312 66 VSS 65 VDD2 64 P4.1/INT4 63 P4.5/INT8 62 IPFC- 15 61 IPFC+ 16 60 IPFCO 17 59 VACO FPWMWH 18 58 VAC- FPWMVL 19 57 VAC+ FPWMVH 20 56 AIN6 FPWMUL 21 55 AIN5 FPWMUH 22 54 AIN4 P2.0/NMI 23 53 AIN3 P2.1 24 52 AIN2 P2.2 25 51 DNC FPWMWL (Top View) IFBCO IFBC- IFBC+ AREF AIN1 CMEXT AVSS AVDD VDC- VDC+ IFBF+ IFBFO AIN0/VDCO IFBF- P4.4/INT7 P4.0/INT3 VDD1 VSS VSS VDD2 P2.7/AOPWM1 P2.5 P2.6/AOPWM0 P2.4 P2.3 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 Figure 3. IRMCK312 Pin Configuration Attention: Pin 51 must be left floating. Do not connect. www.irf.com 8 © 2007 International Rectifier IRMCK312 4 Input/Output of IRMCK312 All I/O signals of IRMCK312 are shown in Figure 4. All I/O pins are 3.3V logic interface except A/D interface pins. Crystal Communication Interface XTAL0 XTAL1 CPWMUH CPWMUL P1.1/RXD P1.2/TXD CPWMVH CPWMVL CPWMWH P3.6/RXD1 P3.7/TXD1 CPWMWL CGATEKILL SDA SCL FPWMUH FPWMUL P1.3/SYNC Discrete I/O D/A Interface (PWM output) P1.4/CAP P3.0/INT2 P1.0/T2 P1.5 P1.6 P1.7 P2.0/NMI FPWMVH FPWMVL FPWMWH FPWMWL FGATEKILL P2.1 P2.2 P2.3 P2.4 P2.5 P3.2/INT0 P3.3/INT1 P3.4/T0 P3.5/T1 P4.0/INT3 P4.1/INT4 P4.2/INT5 P4.3/INT6 P4.4/INT7 P4.5/INT8 P4.6/INT9 P4.7/INT10 P5.0/PGKILL PFCPWM AVDD (1.8V) AVSS System Reset Digital power/ ground PLL power/ ground Channel 2 PWM gate signal Interface Power Factor Control PWM gate signal Interface Analog Power CMEXT AREF IFBC+ IFBCIFBCO IFBF+ IFBFIFBFCO A/D Interface VAC+ VACVACO IPFC+ IPFCIPFCO VDC+ VDCVDCO P2.6/AOPWM0 P2.7/AOPWM1 P3.1/AOPWM2 P5.3/TDI JTAG port Channel 1 PWM gate signal Interface TCLK P5.1/TSM P5.2/TDO AIN1 AIN2 AIN3 AIN4 RESET AIN5 AIN6 VPP(6.75V) VDD1(3.3V) VDD2(1.8V) VSS PLLVDD(1.8V) PLLVSS Figure 4. Input/Output of IRMCK312 www.irf.com 9 © 2007 International Rectifier IRMCK312 4.1 8051 Peripheral Interface Group UART Interface P1.1/RXD P1.2/TXD P3.6/RXD1 P3.7/TXD1 Input, Receive data to IRMCK312, can be configured as P1.1 Output, Transmit data from IRMCK312, can be configured as P1.2 Input, 2nd channel Receive data to IRMCK312, can be configured as P3.6 Output, 2nd channel Transmit data from IRMCK312, can be configured as P3.7 Discrete I/O Interface P1.0/T2 Input/output port 1.0, can be configured as Timer/Counter 2 input P1.3/SYNC/SCK Input/output port 1.3, can be configured as SYNC output or SPI clock P1.4/CAP Input/output port 1.4, can be configured as Capture Timer input P1.5 Input/output port 1.5 P1.6 Input/output port 1.6 P1.7 Input/output port 1.7 P2.0/NMI Input/output port 2.0, can be configured as non-maskable interrupt P2.1 Input/output port 2.1 P2.2 Input/output port 2.2 P2.3 Input/output port 2.3 P2.4 Input/output port 2.4 P2.5 Input/output port 2.5 P3.0/INT2/CS1 Input/output port 3.0, can be configured as external interrupt 2 or SPI chip select 1 P3.2/INT0 Input/output port 3.2, can be configured as external interrupt 0 P3.3/INT1 Input/output port 3.3, can be configured as external interrupt 1 P3.4/T0 Input/output port 3.4, can be configured as Timer/Counter 0 input P3.5/T1 Input/output port 3.5, can be configured as Timer/Counter 1 input P4.0/INT3 Input/output port 4.0, can be configured as external interrupt 3 P4.1/INT4 Input/output port 4.1, can be configured as external interrupt 4 P4.2/INT5 Input/output port 4.2, can be configured as external interrupt 5 P4.3/INT6 Input/output port 4.3, can be configured as external interrupt 6 P4.4/INT7 Input/output port 4.4, can be configured as external interrupt 7 P4.5/INT8 Input/output port 4.5, can be configured as external interrupt 8 P4.6/INT9 Input/output port 4.6, can be configured as external interrupt 9 P4.7/INT10 Input/output port 4.7, can be configured as external interrupt 10 P5.0/PFCGKILL Input/output port 5.0, can be configured as PFCGKILL P5.1/TMS Input/output port 5.1, can be configured as JTAG TMS pin P5.2/TDO Input/output port 5.2, can be configured as JTAG TDO pin P5.3/TDI Input/output port 5.3, can be configured as JTAG TDI pin Analog Output Interface P2.6/AOPWM0 Input/output, can be configured as 8-bit PWM output 0 with programmable carrier frequency P2.7/AOPWM1 Input/output, can be configured as 8-bit PWM output 1 with programmable carrier frequency P3.1/AOPWM2 Input/output, can be configured as 8-bit PWM output 2 with programmable carrier frequency www.irf.com 10 © 2007 International Rectifier IRMCK312 Crystal Interface XTAL0 XTAL1 Reset Interface RESET Input, connected to crystal Output, connected to crystal Inout, system reset, needs to be pulled up to VDD1 but doesn’t require external RC time constant I2C/SPI Interface SCL/SO-SI/VPP Output, I2C clock output, SPI SO-SI SDA/CS0 Input/output, I2C Data line, Chip Select 0 of SPI P3.0/INT2/CS1 Input/output port 3.0, can be configured as external interrupt 2 or SPI chip select 1 P1.3/SYNC/SCK Input/output port 1.3, can be configured as SYNC output or SPI clock 4.2 Motion Peripheral Interface Group PWM CPWMUH CPWMUL CPWMVH CPWMVL CPWMWH CPWMWL FPWMUH FPWMUL FPWMVH FPWMVL FPWMWH FPWMWL PFCPWM Fault CGATEKILL P5.0/PFCGKILL FGATEKILL 4.3 Input, upon assertion, this negates all six PWM signals for motor 1, programmable logic sense Input, upon assertion, this negates PFCPWM signal, programmable logic sense, can be configured as discrete I/O in which case CGATEKILL negates PFCPWM Input, upon assertion, this negates all six PWM signals for motor 2, programmable logic sense Analog Interface Group AVDD AVSS AREF CMEXT www.irf.com Output, motor 1 PWM phase U high side gate signal Output, motor 1 PWM phase U low side gate signal Output, motor 1 PWM phase V high side gate signal Output, motor 1 PWM phase V low side gate signal Output, motor 1 PWM phase W high side gate signal Output, motor 1 PWM phase W low side gate signal Output, motor 2 PWM phase U high side gate signal Output, motor 2 PWM phase U low side gate signal Output, motor 2 PWM phase V high side gate signal Output, motor 2 PWM phase V low side gate signal Output, motor 2 PWM phase W high side gate signal Output, motor 2 PWM phase W low side gate signal Output, PFC PWM Analog power (1.8V) Analog power return Buffered 0.6V output Unbuffered 0.6V, input to the AREF buffer, capacitor needs to be connected. 11 © 2007 International Rectifier IRMCK312 IFBC+ IFBCIFBCO IFBF+ IFBFIFBFO IPFC+ IPFCIPFO VAC+ VACVACO VDC+ VDCAIN0/VDCO AIN1 AIN2 AIN3 AIN4 AIN5 AIN6 4.4 Power Interface Group VDD1 VDD2 VSS PLLVDD PLLVSS SCL/SO-SI/VPP 4.5 Digital power for I/O (3.3V) Digital power for core logic (1.8V) Digital common PLL power (1.8V) PLL ground return OTP programming supply. Can be left open in OTP read mode (normal) Test Interface P5.3/TDI P5.1/TMS TCK P5.2/TDO www.irf.com Input, Operational amplifier positive input for shunt resistor current sensing of motor 1 Input, Operational amplifier negative input for shunt resistor current sensing of motor 1 Output, Operational amplifier output for shunt resistor current sensing of motor 1 Input, Operational amplifier positive input for shunt resistor current sensing of motor 2 Input, Operational amplifier negative input for shunt resistor current sensing of motor 2 Output, Operational amplifier output for shunt resistor current sensing of motor 2 Input, Operational amplifier positive input for PFC current sensing Input, Operational amplifier negative input for PFC current sensing Output, Operational amplifier output for PFC current sensing Input, Operational amplifier positive input for PFC AC voltage sensing Input, Operational amplifier negative input for PFC AC voltage sensing Output, Operational amplifier output for PFC AC voltage sensing Input, Operational amplifier positive input for DC bus voltage sensing Input, Operational amplifier negative input for DC bus voltage sensing Input/Output, Analog input channel 0 or Operational amplifier output for DC bus voltage sensing Input, Analog input channel 1 (0-1.2V), needs to be pulled down to AVSS if unused Input, Analog input channel 2 (0-1.2V), needs to be pulled down to AVSS if unused Input, Analog input channel 3 (0-1.2V), needs to be pulled down to AVSS if unused Input, Analog input channel 4 (0-1.2V), needs to be pulled down to AVSS if unused Input, Analog input channel 5 (0-1.2V), needs to be pulled down to AVSS if unused Input, Analog input channel 6 (0-1.2V), needs to be pulled down to AVSS if unused Input, JTAG test data input Input, JTAG test mode select Input, JTAG test clock Output, JTAG test data output 12 © 2007 International Rectifier IRMCK312 5 Application Connections Typical application connection is shown in Figure 5. All components necessary to implement a complete sensorless drive control algorithm are shown connected to IRMCK312. System Clock XTAL0 XTAL1 4MHz Crystal PLLVDD PLLVSS 1.8V To indoor unit Microcontroller (RS232C) To other Host (RS232C) Other Communication (I2C or SPI) PLL Logic P1.2/TXD P1.1/RXD RS232C P3.7/TXD P3.6/RXD RS232C SDA/CS0 SCL/SO-SI/VPP System clock Motion Control Modules I2C/SPI P1.3/SYNC/SCK P1.4/CAP P1.5 P1.6 PORT1 P1.7 P2.0/NMI P2.1 P2.2 P2.3 P2.4 Digital I/O Control Low Loss Space Vector PWM Dual Port Memory (0.5kB) & MCE Memory (5.5kB) P1.0/T2 PORT2 Low Loss Space Vector PWM Motion Control Sequencer PFC PWM Analog Output P3.1/AOPWM2 PFCPWM PGATEKILL Compressor DC bus shunt resistor 0.6V IFBF+ PORT3 S/H Timers FAN motor DC bus shunt resistor IFBFIFBFO Watchdog Timer S/H IPFCO PORT4 Local RAM 2kByte PWM0 FAN motor DC bus shunt resistor IPFC- VAC+ 12bit A/D & MUX VDC+ P5.3/TDI P5.1/TSM RESET Program OTP ROM (64kB) PWM2 VDCO 6 AIN1 – AIN6 6.75V Power 3.3V 1.8V SCL/SO-SI/VPP System Reset 8051 CPU Other analog input (0-1.2V) Optional External Voltage Reference (0.6V) CMEXT System clock JTAG Port Interface 5 RESET Other Buffered Analog input VDC- PWM1 TCLK P5.2/TDO AC line voltage VACVACOMP AREF JTAG Control 0.6V IPFC+ P4.6/INT9 P4.7/INT10 P2.7/AOPWM1 FPWMWL FGATEKILL IFBC- P3.5/T1 P2.6/AOPWM0 FPWMVH FPWMVL FPWMWH IFBCO P4.0/INT3 P4.1/INT4 P4.4/INT7 P4.5/INT8 FPWMUH FPWMUL 0.6V S/H P3.0/INT2/CS1 P3.2/INT0 P4.2/INT5 P4.3/INT6 CPWMWH CPWMWL CGATEKILL IFBC+ P2.5 P3.3/INT1 P3.4/T0 CPWMUH CPWMUL CPWMVH CPWMVL AVDD Clock divider 1.8V AVSS VDD1 VDD2 VSS Figure 5. Application Connection of IRMCK312 www.irf.com 13 © 2007 International Rectifier IRMCK312 6 DC Characteristics 6.1 Absolute Maximum Ratings Symbol VDD1 VDD2 VPP VIA VID TA TS Parameter Min Typ Max Supply Voltage -0.3 V 3.6 V Supply Voltage -0.3 V 1.98 V OTP Programming -0.3V 7.0V Voltage Analog Input Voltage -0.3 V 1.98 V Digital Input Voltage -0.3 V 3.65 V Ambient Temperature -40 ˚C 85 ˚C Storage Temperature -65 ˚C 150 ˚C Table 1. Absolute Maximum Ratings Condition Respect to VSS Respect to VSS Respect to VSS Respect to AVSS Respect to VSS Caution: Stresses beyond those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only and function of the device at these or any other conditions beyond those indicated in the operational sections of the specifications are not implied. 6.2 System Clock Frequency and Power Consumption Symbol SYSCLK 8051CLK Parameter Min Typ Max Unit System Clock 32 128 8051 Clock 32 Table 2. System Clock Frequency MHz MHz Power Consumption 180 160 140 Power (mW) 120 100 80 1.8V 3.3V 60 Total Power 40 20 0 0 20 40 60 80 100 120 140 MCE Frequency (MHz) Figure 6. Clock Frequency vs. Power Consumption www.irf.com 14 © 2007 International Rectifier IRMCK312 6.3 Digital I/O DC Characteristics Symbol VDD1 VDD2 VPP VIL VIH CIN IL IOL1(2) IOH1(2) IOL2(3) IOH2(3) Parameter Min Typ Max Supply Voltage 3.0 V 3.3 V 3.6 V Supply Voltage 1.62 V 1.8 V 1.98 V OTP Programming 6.50V 6.75V 7.0V voltage Input Low Voltage -0.3 V 0.8 V Input High Voltage 2.0 V 3.6 V Input capacitance 3.6 pF Input leakage current ±10 nA ±1 μA Low level output 8.9 mA 13.2 mA 15.2 mA current High level output 12.4 mA 24.8 mA 38 mA current Low level output 17.9 mA 26.3 mA 33.4 mA current High level output 24.6 mA 49.5 mA 81 mA current Table 3. Digital I/O DC Characteristics Condition Recommended Recommended Recommended Recommended Recommended (1) VO = 3.3 V or 0 V VOL = 0.4 V (1) VOH (1) = 2.4 V VOL (1) = 0.4 V VOH (1) = 2.4 V Note: (1) Data guaranteed by design. (2) Applied to SCL/SO-SI, SDA/CS0 pins. (3) Applied to P1.0/T2, P1.1/RXD, P1.2/TXD, P1.3/SYNC/SCK, P1.4/CAP, P1.5, P1.6, P1.7, P2.0/NMI, P2.1, P2.2, P2.3, P2.4, P2.5, P2.6/AOPWM0, P2.7/AOPWM1, P3.0/INT2/CS1, P3.1/AOPWM2, P3.2/INT0, P3.3/INT1, P3.4/T0, P3.5/T1, P3.6/RXD1, P3.7/TXD1, P4.0/INT3, P4.1/INT4, P4.2/INT5, P4.3/INT6, P4.4/INT7, P4.5/INT8, P4.6/INT9, P4.7/INT10, P5.0/PFCGKILL, P5.1/TMS, P5.2/TDO, P5.3/TDI, CGATEKILL, FGATEKILL, CPWMUL, CPWMUH, CPWMVL, CPWMVH, CPWMWL, CPWMWH, FPWMUL, FPWMUH, FPWMVL, FPWMVH, FPWMWL, FPWMWH, and PFCPWM pins. www.irf.com 15 © 2007 International Rectifier 6.4 PLL and Oscillator DC Characteristics Symbol VPLLVDD VIL OSC Parameter Supply Voltage Oscillator Input Low Voltage Oscillator Input High Voltage Table 4. VIH OSC Min Typ Max 1.62 V VPLLVSS 1.8 V - 1.92 V 0.2* VPLLVDD VPLLVDD 0.8* VPLLVDD PLL DC Characteristics Condition Recommended VPLLVDD = 1.8 V (1) VPLLVDD (1) = 1.8 V Note: (1) Data guaranteed by design. 6.5 Analog I/O DC Characteristics - OP amps for current sensing (IFBC+, IFBC-, IFBCO, IFBF+, IFBF-, IFBFO, IPFC+, IPFC-, IPFCO) CAREF = 1nF, CMEXT= 100nF. Unless specified, Ta = 25˚C. Symbol VAVDD VOFFSET VI VOUTSW CIN RFDBK OP GAINCL Parameter Min Typ Max Supply Voltage Input Offset Voltage Input Voltage Range OP amp output operating range Input capacitance OP amp feedback resistor 1.71 V 0V 50 mV 1.8 V - 1.89 V 26 mV 1.2 V 1.2 V Recommended VAVDD = 1.8 V Recommended VAVDD = 1.8 V 5 kΩ 3.6 pF - 20 kΩ (1) (1) Operating Close loop 80 db Gain CMRR Common Mode 80 db Rejection Ratio ISRC Op amp output 1 mA source current ISNK Op amp output sink 100 μA current Table 5. Analog I/O DC Characteristics Note: (1) Data guaranteed by design. Rev 1.0 Condition Requested between op amp output and negative input (1) (1) VOUT (1) = 0.6 V VOUT (1) = 0.6 V 6.6 Under Voltage Lockout DC Characteristics - Based on AVDD (1.8V) Unless specified, Ta = 25˚C. Symbol UVCC+ Parameter Min Typ Max UVcc positive going 1.53 V 1.66 V 1.71 V Threshold1) UVcc negative going 1.52 V 1.62 V 1.71 V Threshold UVcc Hysteresys 40 mV Table 6. UVcc DC Characteristics UVCCUVCCH Condition VDD1 = 3.3 V VDD1 = 3.3 V Note: 1) Data guaranteed by design. 6.7 AREF Characteristics CAREF = 1nF, CMEXT= 100nF. Unless specified, Ta = 25˚C. Symbol VAREF ΔVo PSRR Parameter Typ Max AREF Output Voltage 495 mV 600 mV 700 mV Load regulation (VDC-0.6) 1 mV Power Supply Rejection 75 db Ratio Table 7. AREF DC Characteristics Note: (1) Data guaranteed by design. Rev 1.0 Min Condition VAVDD (1) (1) = 1.8 V IRMCK312 7 AC Characteristics 7.1 PLL AC Characteristics Symbol FCLKIN FPLL FLWPW JS D TLOCK Parameter Min Typ Max Crystal input 3.2 MHz 4 MHz 60 MHz frequency Internal clock 32 MHz 50 MHz 128 MHz frequency Sleep mode output FCLKIN ÷ 256 frequency Short time jitter 200 psec Duty cycle 50 % PLL lock time 500 μsec Table 8. PLL AC Characteristics Condition (1) (see figure below) (1) (1) (1) (1) (1) Note: (1) Data guaranteed by design. R1=1M R2=10 Xtal C1=30PF C2=30PF Figure 7 Crystal oscillator circuit www.irf.com 18 © 2007 International Rectifier IRMCK312 7.2 Analog to Digital Converter AC Characteristics Unless specified, Ta = 25˚C. Symbol TCONV THOLD Parameter Min Conversion time Sample/Hold maximum hold time Typ - Max - 2.05 μsec 10 μsec Condition (1) Voltage droop ≤ 15 LSB (see figure below) Table 9. A/D Converter AC Characteristics Note: (1) Data guaranteed by design. Input Voltage Voltage droop S/H Voltage tSAMPLE THOLD Figure 8 Voltage droop of sample and hold 7.3 Op Amp AC Characteristics - OP amps for current sensing (IFBC+, IFBC-, IFBCO, IFBF+, IFBF-, IFBFO, IPFC+, IPFC-, IPFCO) Unless specified, Ta = 25˚C. Min Typ Max Condition OPSR Symbol OP amp slew rate Parameter - 10 V/μsec - OPIMP TSET OP input impedance Settling time - 108 Ω 400 ns VAVDD = 1.8 V, CL = 33 pF (1) - (1) VAVDD = 1.8 V, CL = 33 pF (1) Table 10. Current Sensing OP Amp AC Characteristics Note: (1) Data guaranteed by design. www.irf.com 19 © 2007 International Rectifier IRMCK312 7.4 SYNC to SVPWM and A/D Conversion AC Timing twSYNC SYNC tdSYNC1 IU,IV,IW tdSYNC2 AINx tdSYNC3 PWMUx,PWMVx,PWMWx Figure 9 SYNC to SVPWM and A/D conversion AC Timing Unless specified, Ta = 25˚C. Symbol twSYNC tdSYNC1 tdSYNC2 tdSYNC3 Parameter Min Typ Max Unit SYNC pulse width 32 100 SYNC to current feedback conversion time 200 SYNC to AIN0-6 analog input conversion time SYNC to PWM output 2 delay time Table 11. SYNC AC Characteristics SYSCLK SYSCLK SYSCLK (1) SYSCLK Note: (1) AIN1 through AIN6 channels are converted once every 6 SYNC events www.irf.com 20 © 2007 International Rectifier IRMCK312 7.5 GATEKILL to SVPWM AC Timing Figure 10 GATEKILL to SVPWM AC Timing Unless specified, Ta = 25˚C. Symbol twGK tdGK 7.6 Parameter Min Typ Max GATEKILL pulse width 32 GATEKILL to PWM 100 output delay Table 12. GATEKILL to SVPWM AC Timing Unit SYSCLK SYSCLK Interrupt AC Timing Figure 11 Interrupt AC Timing Unless specified, Ta = 25˚C. Symbol Parameter twINT INT0, INT1 Interrupt 4 Assertion Time INT0, INT1 latency 4 Table 13. Interrupt AC Timing tdINT www.irf.com Min Typ 21 Max Unit SYSCLK SYSCLK © 2007 International Rectifier IRMCK312 7.7 I2C AC Timing TI2CLK TI2CLK SCL tI2WSETUP tI2ST1 tI2WHOLD tI2RSETUP tI2EN1 tI2RHOLD tI2ST2 tI2EN2 SDA Figure 12 I2C AC Timing Unless specified, Ta = 25˚C. Symbol TI2CLK tI2ST1 tI2ST2 tI2WSETUP tI2WHOLD tI2RSETUP tI2RHOLD Parameter 2 I C clock period I2C SDA start time I2C SCL start time I2C write setup time I2C write hold time I2C read setup time I2C read hold time Min Typ Max Unit 10 0.25 0.25 0.25 0.25 I2C filter time(1) 1 Table 14. I2C AC Timing 8192 - SYSCLK TI2CLK TI2CLK TI2CLK TI2CLK SYSCLK SYSCLK Note: (1) I2C read setup time is determined by the programmable filter time applied to I2C communication. www.irf.com 22 © 2007 International Rectifier IRMCK312 7.8 SPI AC Timing 7.8.1 SPI Write AC timing Figure 13 SPI AC Timing Unless specified, Ta = 25˚C. Symbol TSPICLK tSPICLKHT tSPICLKLT tCSDELAY tWRDELAY tCSHIGH tCSHOLD www.irf.com Parameter Min Typ Max SPI clock period 4 SPI clock high time 1/2 SPI clock low time 1/2 CS to data delay time 10 CLK falling edge to data 10 delay time CS high time between two 1 consecutive byte transfer CS hold time 1 Table 15. SPI Write AC Timing 23 Unit SYSCLK TSPICLK TSPICLK nsec nsec TSPICLK TSPICLK © 2007 International Rectifier IRMCK312 7.8.2 SPI Read AC Timing Figure 14 SPI Read AC Timing Unless specified, Ta = 25˚C. Symbol TSPICLK tSPICLKHT tSPICLKLT tCSRD tRDSU tRDHOLD tCSHIGH tCSHOLD www.irf.com Parameter Min Typ Max SPI clock period 4 SPI clock high time 1/2 SPI clock low time 1/2 CS to data delay time 10 SPI read data setup time 10 SPI read data hold time 10 CS high time between two 1 consecutive byte transfer CS hold time 1 Table 16. SPI Read AC Timing 24 Unit SYSCLK TSPICLK TSPICLK nsec nsec nsec TSPICLK TSPICLK © 2007 International Rectifier IRMCK312 7.9 UART AC Timing TBAUD TXD Data and Parity Bit Start Bit Stop Bit RXD TUARTFIL Figure 15 UART AC Timing Unless specified, Ta = 25˚C. Symbol TBAUD TUARTFIL Parameter Min Typ Baud Rate Period 57600 UART sampling filter 1/16 period (1) Table 17. UART AC Timing Max Unit - bit/sec TBAUD Note: (1) Each bit including start and stop bit is sampled three times at center of a bit at an interval of 1/16 TBAUD. If three sampled values do not agree, then UART noise error is generated. www.irf.com 25 © 2007 International Rectifier IRMCK312 7.10 CAPTURE Input AC Timing Figure 16 CAPTURE Input AC Timing Unless specified, Ta = 25˚C. Symbol TCAPCLK tCAPHIGH tCAPLOW tCRDELAY tCLDELAY tINTDELAY www.irf.com Parameter Min Typ CAPTURE input period 8 CAPTURE input high 4 time CAPTURE input low 4 time CAPTURE falling edge to capture register latch time CAPTURE rising edge to capture register latch time CAPTURE input interrupt latency time Table 18. CAPTURE AC Timing 26 Max Unit - SYSCLK SYSCLK - SYSCLK 4 SYSCLK 4 SYSCLK 4 SYSCLK © 2007 International Rectifier IRMCK312 7.11 JTAG AC Timing TJCLK TCK tJHIGH tJLOW tCO TDO tJSETUP tJHOLD TDI/TMS Figure 17 JTAG AC Timing Unless specified, Ta = 25˚C. Symbol TJCLK tJHIGH tJLOW tCO tJSETUP tJHOLD www.irf.com Parameter Min Typ TCK Period TCK High Period 10 TCK Low Period 10 TCK to TDO propagation 0 delay time TDI/TMS setup time 4 TDI/TMS hold time 0 Table 19. JTAG AC Timing 27 Max Unit 50 5 MHz nsec nsec nsec - nsec nsec © 2007 International Rectifier IRMCK312 7.12 OTP Programming Timing Figure 18 OTP Programming Timing Unless specified, Ta = 25˚C. Symbol TVPS TVPH www.irf.com Parameter Min Typ Max VPP Setup Time 10 VPP Hold Time 15 Table 20. OTP Programming Timing 28 Unit nsec nsec © 2007 International Rectifier IRMCK312 8 I/O Structure The following figure shows the motor PWM and digital I/O structure except the motor PWM output Figure 19 All digital I/O except motor PWM output The following figure shows RESET and GATEKILL I/O structure. Figure 20 RESET, GATEKILL I/O www.irf.com 29 © 2007 International Rectifier IRMCK312 The following figure shows the analog input structure. AVDD Analog input 6.0V PIN 100 Analog Circuit 6.0V AVSS Figure 21 Analog input The following figure shows all analog operational amplifier output pins and AREF pin I/O structure. 1.8V Analog output 6.0V PIN Analog Circuit 6.0V AVSS Figure 22 Analog operational amplifier output and AREF I/O structure The following figure shows the VPP pin I/O structure Figure 23 VPP programming pin I/O structure The following figure shows the VSS, AVSS and PLLVSS pin structure www.irf.com 30 © 2007 International Rectifier IRMCK312 Figure 24 VSS, AVSS and PLLVSS pin structure The following figure shows the VDD1, VDD2, AVDD and PLLVDD pin structure PIN 6.0V VSS Figure 25 VDD1, VDD2, AVDD and PLLVDD pin structure The following figure shows the XTAL0 and XTAL1 pins structure Figure 26 XTAL0/XTAL1 pins structure www.irf.com 31 © 2007 International Rectifier IRMCK312 9 Pin List Pin Number 1 2 3 4 5 6 Pin Name Internal IC Pin Pull-up Type /Pull-down 7 8 9 10 11 12 13 14 15 16 XTAL0 XTAL1 P1.0/T2 P1.1/RXD P1.2/TXD P1.3/SYNC/ SCK P1.4/CAP P1.5 P1.6 P1.7 P4.3/INT6 P4.7/INT10 VDD2 VSS VDD1 FGATEKILL 17 FPWMWL 18 FPWMWH 19 FPWMVL 20 FPWMVH 21 FPWMUL 22 FPWMUH 23 P2.0/NMI I/O 24 25 26 27 28 29 P2.1 P2.2 P2.3 P2.4 P2.5 P2.6/ AOPWM0 P2.7/ AOPWM1 VDD2 I/O I/O I/O I/O I/O I/O 30 31 www.irf.com Description I O I/O I/O I/O I/O Crystal input Crystal output Discrete programmable I/O or Timer/Counter 2 input Discrete programmable I/O or UART receive input Discrete programmable I/O or UART transmit output Discrete programmable I/O or SYNC output or SPI clock output Discrete programmable I/O or Capture Timer input Discrete programmable I/O Discrete programmable I/O Discrete programmable I/O Discrete programmable I/O or Interrupt 6 Discrete programmable I/O or Interrupt 10 1.8V digital power Digital common 3.3V digital power Fan PWM shutdown input, 2-μsec digital filter, configurable either high or low true. Fan PWM gate drive for phase W low side, configurable either high or low true Fan PWM gate drive for phase W high side, configurable either high or low true Fan PWM gate drive for phase V low side, configurable either high or low true Fan PWM gate drive for phase V high side, configurable either high or low true Fan PWM gate drive for phase U low side, configurable either high or low true Fan PWM gate drive for phase U high side, configurable either high or low true Discrete programmable I/O or Non Maskable Interrupt Discrete programmable I/O Discrete programmable I/O Discrete programmable I/O Discrete programmable I/O Discrete programmable I/O Discrete programmable I/O or analog output 0 (PWM) Discrete programmable I/O or analog output 1 (PWM) 1.8V digital power I/O I/O I/O I/O I/O I/O P P P I 70 kΩ Pull up 70 kΩ Pull up 70 kΩ Pull up 70 kΩ Pull up 70 kΩ Pull up 70 kΩ Pull up O O O O O O I/O P 32 © 2007 International Rectifier IRMCK312 Pin Number Pin Name 32 33 34 35 36 37 38 39 40 VSS VSS VDD1 P4.0/INT3 P4.4/INT7 IFBFIFBF+ IFBFO AIN0/VDCO 41 42 43 44 45 VDC+ VDCAVDD AVSS AIN1 I I P P I 46 47 48 CMEXT AREF IFBC- O O I 49 IFBC+ I 50 IFBCO O 51 52 DNC AIN2 I 53 AIN3 I 54 AIN4 I 55 AIN5 I 56 AIN6 I 57 58 59 60 61 62 63 64 65 VAC+ VACVACO IPFCO IPFC+ IPFCP4.5/INT8 P4.1/INT4 VDD2 www.irf.com Internal IC Pin Pull-up Type /Pull-down Description P P P I/O I/O I I O O Digital common Digital common 3.3 V digital power Discrete programmable I/O or Interrupt 3 Discrete programmable I/O or Interrupt 7 Fan single shunt current sensing OP amp input (-) Fan single shunt current sensing OP amp input (+) Fan single shunt current sensing OP amp output Analog input channel 0 or DC bus voltage sensing OP amp output DC bus voltage sensing OP amp input (+) DC bus voltage sensing OP amp input (-) Analog power (1.8V) Analog common Analog input channel 1, 0-1.2V range, needs to be pulled down to AVSS if unused Unbuffered analog reference voltage output (0.6V) Analog reference voltage output (0.6V) Compressor single shunt current sensing OP amp input (-) Compressor single shunt current sensing OP amp input (+) Compressor single shunt current sensing OP amp output Do not connect. Analog input channel 2, 0-1.2V range, needs to be pulled down to AVSS if unused Analog input channel 2, 0-1.2V range, needs to be pulled down to AVSS if unused Analog input channel 2, 0-1.2V range, needs to be pulled down to AVSS if unused Analog input channel 2, 0-1.2V range, needs to be pulled down to AVSS if unused Analog input channel 2, 0-1.2V range, needs to be pulled down to AVSS if unused AC input voltage sensing OP amp input (+) AC input voltage sensing OP amp input (-) AC input voltage sensing OP amp output PFC shunt current sensing OP amp output PFC shunt current sensing OP amp input (+) PFC shunt current sensing OP amp input (-) Discrete programmable I/O or Interrupt 8 Discrete programmable I/O or Interrupt 4 1.8 V digital power I I O O I I I/O I/O P 33 © 2007 International Rectifier IRMCK312 Pin Number Pin Name 66 67 68 VSS VDD1 CGATEKILL 69 CPWMWL 70 CPWMWH 71 CPWMVL 72 CPWMVH 73 CPWMUL 74 CPWMUH 75 P3.0/INT2/ CS1 P5.0/ PFCGKILL 76 Internal IC Pin Pull-up Type /Pull-down P P I 70 kΩ Pull up 70 kΩ Pull up 70 kΩ Pull up 70 kΩ Pull up 70 kΩ Pull up 70 kΩ Pull up Digital common 3.3V digital power Compressor PWM shutdown input, 2-μsec digital filter, configurable either high or low true. Compressor PWM gate drive for phase W low side, configurable either high or low true Compressor PWM gate drive for phase W high side, configurable either high or low true Compressor PWM gate drive for phase V low side, configurable either high or low true Compressor PWM gate drive for phase V high side, configurable either high or low true Compressor PWM gate drive for phase U low side, configurable either high or low true Compressor PWM gate drive for phase U high side, configurable either high or low true Discrete programmable I/O or INT2 digital input or SPI Chip Select 1 Discrete programmable I/O or PFC PWM shutdown input, 2-μsec digital filter, configurable either high or low true. PFC PWM gate drive, configurable either high or low true Discrete programmable I/O or analog output 2 (PWM) Discrete programmable I/O or external interrupt 0 Discrete programmable I/O or external interrupt 1 Discrete programmable I/O or Timer/Counter 0 input Discrete programmable I/O or Timer/Counter 1 input Discrete programmable I/O or 2nd UART receive input Discrete programmable I/O or 2nd UART transmit output Digital common Digital common 3.3V digital power Discrete programmable I/O or Interrupt 5 Discrete programmable I/O or Interrupt 9 I2C clock output or SPI data or OTP power supply during programming I2C data or SPI Chip Select 0 Discrete programmable I/O or JTAG test mode select Discrete programmable I/O or JTAG port test data output O O O O O O I/O I 77 PFCPWM 78 79 80 81 82 83 P3.1/ AOPWM2 P3.2/INT0 P3.3/INT1 P3.4/T0 P3.5/T1 P3.6/RXD1 I/O I/O I/O I/O I/O 84 P3.7/TXD1 I/O 85 86 87 88 89 90 P P P I/O I/O I/O 91 92 VSS VSS VDD1 P4.2/INT5 P4.6/INT9 SCL/SOSI/VPP SDA/CS0 P5.1/TMS 93 P5.2/TDO I/O www.irf.com Description 70 kΩ Pull up O I/O I/O I/O 34 © 2007 International Rectifier IRMCK312 Pin Number Pin Name 94 95 96 P5.3/TDI TCK TSTMOD 97 98 99 100 RESET VDD2 PLLVDD PLLVSS www.irf.com Internal IC Pin Pull-up Type /Pull-down 58 kΩ pull down Description I/O I I Discrete programmable I/O or JTAG test data input JTAG test clock Test mode. Must be tied to VSS. Factory use only I/O Reset, low true, Schmitt trigger input P 1.8V digital power P 1.8V PLL power. P PLL ground. Table 21. Pin List 35 © 2007 International Rectifier IRMCK312 10 Package Dimensions www.irf.com 36 © 2007 International Rectifier IRMCK312 11 Part Marking Information 12 Ordering Information Lead-Free Part in 100-lead QFP Moisture sensitivity rating – MSL3 Part number IRMCK312TR Order quantities 1000 parts on tape and reel in dry pack The LQFP-100 is MSL3 qualified This product has been designed and qualified for the industrial level Qualification standards can be found at www.irf.com <http://www.irf.com> IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, Tel: (310) 252-7105 Data and specifications subject to change without notice. 12/25/2007 www.irf.com 37 © 2007 International Rectifier