Data Sheet No. PD94726 IR3629/IR3629A MPbF HIGH FREQUENCY SYNCHRONOUS PWM BUCK CONTROLLER WITH POWER GOOD OUTPUT Features Description • • • • The • • • • • • Internal 600kHz Oscillator (300kHz “A version”) Operates with Single 5V or 12V Supply Programmable Over Current Protection Hiccup Current Limit Using MOSFET RDS(on) sensing Precision Reference Voltage (0.6V) Programmable Soft-Start Programmable PGood output Pre-Bias Start-up Thermal Protection 12-Lead MLP Package IR3629/IR3629A is a PWM controller designed for high performance synchronous Buck DC/DC applications. The IR3629/IR3629A drives a pair of external N-MOSFETs using a fixed 600kHz (300kHz “A version”) switching frequency allowing the use of small external components. The output voltage can be precisely regulated using the internal 0.6V reference voltage for low voltage applications. Protection such as Pre-Bias startup, hiccup current limit and thermal shutdown Applications provide the required system level security in the • • • • • • • event of fault conditions. Distributed Point-of-Loads Embedded Systems Storage Systems DDR Applications Graphics Cards Computing Peripheral Voltage Regulators General DC-DC Converters Fig. 1: Typical application Circuit ORDERING INFORMATION PKG DESIG M M 11/26/2007 PACKAGE PIN DESCRIPTION COUNT IR3629/IR3629AMPBF 12 IR3629/IR3629AMTRPBF 12 PARTS PARTS T&R PER TUBE PER REEL ORIENTATION 122 -------------3000 Figure A IR3629/IR3629A MPbF ABSOLUTE MAXIMUM RATINGS (Voltages referenced to GND) • Vcc Supply Voltage ................................................… -0.5V to 16V • Vc Supply Voltage …………………………………….. -0.5V to 30V • PGood ………………………………………………… -0.5V to 16V • Fb, Comp, SS ……………………..………………….. -0.3V to 3.5V • OCset • AGnd to PGnd ………………………………….…….. -0.3V to +0.3V • Storage Temperature Range ..................................... -65°C To 150°C • Operating Junction Temperature Range ................... -40°C To 150°C • ESD Classification …………………………………..… JEDEC, JESD22-A114 • Moisture Sensitivity Level ……………………………. JEDEC Level 2 @ 260oC ………………………………………………… 10mA Caution: Stresses beyond those listed under “Absolute Maximum Rating” may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to “Absolute Maximum Rating” conditions for extended periods may affect device reliability. Package Information PGood 1 12 OCSet VCC 2 11 SS/SD LDrv 3 10 Gnd PGnd 4 9 Comp HDrv 5 8 Fb VC 6 7 Vsns Exposed Pad 12-Lead MLPD, 3x4mm ΘJA = 30o C/W * ΘJC = 2o C/W *Exposed pad on underside is connected to a copper pad through vias for 4-layer PCB board design 11/26/2007 2 IR3629/IR3629A MPbF Block Diagram Fig. 2: Simplified block diagram of the IR3629/IR3629A 11/26/2007 3 IR3629/IR3629A MPbF Pin Description Pin Name 1 PGood 2 Vcc 3 LDrv 4 PGnd 5 HDrv 6 Vc 7 Vsns 8 Fb 9 Comp 10 Gnd 11 SS/SD 12 OCSet 11/26/2007 Description Power Good status pin. Output is open collector. Connect a pull up resistor from this pin to Vcc. This pin provides biasing voltage for the internal blocks of the IC. It also biases the low side driver. A minimum of 0.1uF, high frequency capacitor must be connected from this pin to power ground. Output driver for the low side MOSFET Power Ground. This pin serves as a separate ground for the MOSFET drivers and should be connected to the system’s power ground plane. Output driver for the high side MOSFET This pin powers the high side driver and must be connected to a voltage higher than bus voltage. A minimum of 0.1uF, high frequency capacitor must be connected from this pin to power ground. PGood sense pin Inverting input to the error amplifier. This pin is connected directly to the output of the regulator via resistor divider to set the output voltage and provide feedback to the error amplifier. Output of the error amplifier. Signal ground for internal reference and control circuitry. Soft start / shutdown. This pin provides user programmable soft-start function. Connect an external capacitor from this pin to ground to set the start up time of the output voltage. The converter can be shutdown by pulling this pin below 0.3V. Current limit set point. A resistor from this pin to drain of the low side MOSFET will set the current limit threshold. 4 IR3629/IR3629A MPbF Recommended Operating Conditions Symbol Definition Min Max Units Vcc Vc Tj (Note1) Supply Voltage Supply Voltage Junction Temperature 4.5 Converter voltage + 5V -40 14 28 125 V V o C Note1: The junction temperature for 5V application is 0oC-125oC Electrical Specifications Unless otherwise specified, these specification apply over Vcc=Vc=12V, 0oC<Tj< 105oC Typical value are specified at Ta=25oC Parameter SYM Test Condition Min TYP MAX Units Accuracy Feedback Voltage VFB 0.6 o Accuracy o 0 C<Tj<125 C o o -40 C<Tj<105 C, Note2 -1.5 -2.5 V +1.5 +1.5 % Supply Current VCC Supply Current ICC(Static) SS=0V, No Switching 10 13 VCC Supply Current ICC(Dynamic) IR3629, CLOAD=1.5nF 15 25 IR3629A, CLOAD=1.5nF 15 19 SS=0V, No Switching 4.5 7 (Static) (Dynamic) VC Supply Current IC(Static) VC Supply Current (Dynamic) IC(Dynamic) (Static) IR3629, CLOAD=1.5nF 17 25 IR3629A, CLOAD=1.5nF 10 15 mA Under Voltage Lockout VCC-Start-Threshold VCC-Stop-Threshold VCC-Hysteresis VC-Start-Threshold VC-Stop-Threshold VC-Hysteresis VCC_UVLO(R) VCC_UVLO(F) VCC_Hys VC_UVLO(R) VC_UVLO(F) VC_Hys Supply ramping up Supply ramping down Supply ramping up and down Supply ramping up Supply ramping down Supply ramping up and down 4.0 3.7 0.15 3.1 2.85 0.15 4.2 3.9 0.25 3.3 3.05 0.2 4.4 4.1 0.3 3.5 3.25 0.25 IR3629A 270 300 330 IR3629 540 600 660 V Oscillator Frequency FS Ramp Amplitude Vramp Note3 Min Duty Cycle Dmin Fb=1V 0 IR3629, Note3 80 Min Pulse Width Dmin(ctrl) IR3629A , Note3 160 Max Duty Cycle Dmax 11/26/2007 1.25 IR3629, Fb=0.5V 71 IR3629A, Fb=0.5V 78 kHz V % ns % 5 IR3629/IR3629A MPbF Parameter SYM Test Condition Min TYP MAX -0.1 -0.5 20 35 50 Units Error Amplifier Input Bias Current IFB1 SS=3V Input Bias Current IFB2 SS=0V Source/Sink Current I(source/Sink) 50 70 90 Transconductance gm 1000 1300 1600 μmho 15 20 28 μA 0.25 V μA Soft Start/SD Soft Start Current ISS Shutdown Threshold SD Output SS=0V Over Current Protection OCSET Current Hiccup Current Hiccup Duty Cycle IOCSET IHiccup Hiccup(duty) 15 20 3 15 26 0.35 0.38 0.41 V 15 27.5 40 mV 0.25 0.5 V 0.3 1 μA Note3 IHiccup / ISS , Note3 μA % Power Good Vsns Lower Trip Point Vsns(trip) Hysteresis PGood(Hys) Pgood Output Low Voltage Input Bias Curent PG(voltage) Vsns ramping Down IPgood =4mA ISns 0 Thermal Shutdown Thermal Threshold Thermal Hysteresis Shutdown TD Note3 140 Shutdown TD(Hys) Note3 20 o C Output Drivers LO, Drive Rise Time Tr(Lo) CL=1.5nF, See Fig 3 30 60 HI Drive Rise Time Tr(Hi) CL=1.5nF, See Fig 3 30 60 LO Drive Fall Time Tf(Lo) CL=1.5nF, See Fig 3 30 60 HI Drive Fall Time Tf(Hi) CL=1.5nF, See Fig 3 30 60 Dead Band Time Tdead See Fig 3 50 100 10 ns Note2: Cold temperature performance is guaranteed via correlation using statistical quality control. Not tested in production. Note3: Guaranteed by Design but not tested in production. Tr Tf 9V High Side Driver (HDrv) 2V Tr Tf 9V Low Side Driver (LDrv) 2V Deadband H_to_L Deadband L_to_H Fig. 3: Definition of Rise/Fall time and Deadband Time 11/26/2007 6 IR3629/IR3629A MPbF TYPICAL OPERATING CHARACTERISTICS Iss(mA) 601.0 25.0 600.5 24.0 600.0 23.0 599.5 22.0 [uA] [mV] Vfb(mV) 599.0 21.0 20.0 598.5 19.0 598.0 18.0 597.5 17.0 597.0 -40 -20 0 20 40 60 80 100 -40 120 -20 0 20 12.0 6.0 11.0 5.5 10.0 5.0 9.0 80 100 120 60 80 100 120 4.5 8.0 4.0 7.0 3.5 3.0 6.0 -40 -20 0 20 40 60 80 100 -40 120 -20 0 20 40 Temp[oC] Temp[oC] Iocset(uA) Transconductance (gm)[mMHO] 1.5 22.0 1.4 21.5 1.4 21.0 1.3 20.5 1.3 [uA] [mMHO] 60 Ic(Static)(mA) [mA] [mA] Icc(static)(mA) 1.2 20.0 19.5 1.2 1.1 19.0 1.1 18.5 1.0 18.0 -40 -20 0 20 40 60 80 100 120 -40 -20 0 20 Temp[oC] 40 60 80 100 120 140 80 100 120 140 Temp[oC] Frequency (kHz)(IR3629) Frequency(kHz)(IR3629A) 615.0 310.0 610.0 305.0 605.0 300.0 600.0 295.0 595.0 [kHz] [kHz] 40 Temp[oC] Temp[oC] 590.0 290.0 285.0 585.0 580.0 280.0 575.0 275.0 570.0 270.0 -40 -20 0 20 40 60 Temp[oC] 11/26/2007 80 100 120 140 -40 -20 0 20 40 60 Temp[oC] 7 IR3629/IR3629A MPbF Circuit Description THEORY OF OPEARTION Introduction The IR3629/29A is a voltage mode PWM synchronous controller and operates with a fixed 600kHz (300kHz for IR3629A) switching frequency, allowing the use of small external components. The output voltage is set by a feedback pin (Fb) and the internal reference voltage (0.6V). These are the two inputs to the error amplifier. The error signal between these two inputs is amplified and it is compared to a fixed frequency linear sawtooth ramp and generates fixed frequency pulses of variable duty-cycle (D) which drivers N-channel external MOSFETs. The internal oscillator circuit uses an on-chip capacitor to set the switching frequency. The IR3629/29A operates with single input voltage from 4.5V to 12V allowing an extended operating input voltage range. The current limit is programmable and uses onresistance of the low-side MOSFET, eliminating the need for an external current sense resistor. Under-Voltage Lockout The under-voltage lockout circuit monitors the two input supplies (Vcc and Vc) and ensures that the MOSFET driver outputs remain in the off state whenever the supply voltage drops below set thresholds. Lockout occurs if Vc or Vcc fall below 3.3V and 4.2V respectively. Normal operation resumes once Vc and Vcc rise above the set values. Thermal Shutdown Temperature sensing is provided inside the IR3629/29A. The trip threshold is typically set to 145oC. When the trip threshold is exceeded, thermal shutdown discharges the Soft Start voltage and turns off both MOSFETs. Thermal shutdown is not latched and automatic restart is initiated when the sensed temperature drops within the operating range. There is a 20oC hysteresis in the thermal shutdown threshold. 11/26/2007 Power Good The IR3629/29A provides an open collector power good signal which reports the status of the output. The output is sensed through the dedicated Vsns pin. The power good threshold can be externally programmed using two external resistors. The power good comparator is internally set to 0.38V (typical). Shutdown The output can be shutdown by pulling the softstart pin below 0.3V. This can easily be done by using an external small signal transistor. During shutdown both MOSFET drivers will be turned off. Normal operation will resume by cycling the soft start pin. Pre-Bias Startup The IR3629/29A is able to start up into precharged output, which prevents oscillation and disturbances of the output voltage. The output starts in asynchronous fashion and keeps the synchronous MOSFET off until the first gate signal for control MOSFET is generated. Figure 4 shows a typical Pre-Bias condition at startup. Depending on the system configuration, specific amount of output capacitors may be required to prevent discharging the output voltage. Volt Vo Pre-Bias Voltage (Output Voltage before startup) Time Fig. 4: Pre-Bias startup Minimum Pulse Width The time required for turning on and off the high side MOSFET is defined as “Minimum Pulse Width”. To ensure that a reliable operation is achieved the following condition needs to be met: Vout Ton(min) < Vin(max) * Fs 8 IR3629/IR3629A MPbF Soft-Start The IR3629/29A has a programmable soft-start to control the output voltage rise and limit the inrush current during start-up. To ensure correct start-up, the soft-start sequence initiates when Vcc and Vc rise above their threshold and generate the Power On Ready (POR) signal. The soft-start function operates by sourcing current to charge an external capacitor to about 3V. Initially, the soft-start function clamps the output of error amplifier by injecting a current (35uA) into the Fb pin and generates a voltage about 0.84V (35ux24K) across the negative input of error amplifier (see figure 5). The magnitude of the injected current is inversely proportional to the voltage at the soft-start pin. As the soft-start voltage ramps up, the injected current decreases linearly and so does the voltage at the negative input of error amplifier. When the soft-start capacitor voltage is around 1V, the voltage at the positive input of the error amplifier is approximately 0.6V. The output of the error amplifier will start increasing and generating the first PWM signal. As the soft-start capacitor voltage continues to rise up, the current flowing into the Fb pin will keep decreasing. The feedback voltage increases linearly as the soft-start voltage ramps up. When soft-start voltage is around 2V the output voltage reaches the steady state and the injected current is zero. Figure 6 shows the theoretical waveforms during soft-start. operating The output voltage start-up time is the time period when soft-start capacitor voltage increases from 1V to 2V. The start-up time will be dependent on the size of the external soft-start capacitor and can be estimated by: 20μA ∗ 3V 20uA SS/SD 35uA 40uA POR Comp 0.6V Fb Error Amp 24K 24K Fig. 5: Soft-Start circuit for IR3629/29A Output of UVLO POR 3V ≅2V Soft-Start Voltage ≅1V 0V 35uA 40uA Current flowing into Fb pin 0uA Voltage at negative input ≅0.96V of Error Amp 0.84V 0.6V 0.6V Voltage at Fb pin 0V Fig. 6: Theoretical operation waveforms during soft-start Tstart = 2V −1V Css For a given start-up time, the soft-start capacitor (nF) can be estimated as: CSS ≅ 20μA * Tstart (ms) 11/26/2007 --(1) 9 IR3629/IR3629A MPbF Over-Current Protection 28uA The over current protection is performed by sensing current through the RDS(on) of the lowside MOSFET. This method enhances the converter’s efficiency and reduces cost by eliminating a current sense resistor. As shown in figure 7, an external resistor (RSET) is connected between OCSet pin and the drain of the low-side MOSFET (Q2) which determines the current limit set point. The internal current source develops a voltage across RSET. When the low-side MOSFET is turned on, the inductor current flows through the Q2 and results in a voltage which is given by: VOCSet = (IOCSet ∗ ROCSet ) − (RDS(on) ∗ IL ) --(2 ) IOCSET IR3624 IR3629/29A Q1 L1 OCSet RSET VOUT OCP 20uA SS1 / SD 20 3uA Fig. 8: 3uA current source for discharging soft-start capacitor during hiccup The OCP circuit starts sampling current when the low gate drive is about 3V. The OCSet pin is internally clamped during deadtime to prevent false trigging. Figure 9 shows the OCSet pin during one switching cycle. As shown, there is about 150ns delay to mask the deadtime. Since this node contains switching noises, this delay also functions as a filter. Q2 Hiccup Control Fig. 7: Connection of over current sensing resistor Deadtime The critical inductor current can be calculated by setting: VOCSet = (IOCSet ∗ ROCSet ) − (RDS(on) ∗ IL ) = 0 ISET = IL(critical) = ROCSet ∗ IOCSet RDS(on) Blanking time Clamp voltage --(3 ) An over-current is detected if the OCSet pin goes below ground. This trips the OCP comparator and cycles the soft start function in hiccup mode. The hiccup is performed by charging and discharging the soft-start capacitor in a certain slope rate. As shown in figure 8, a 3uA current source is used to discharge the soft-start capacitor. The OCP comparator resets after every soft start cycle. The converter stays in this mode until the overload or short circuit is removed. The converter will automatically recover. 11/26/2007 IOCSet*ROCSet Fig. 9: OCset pin during normal condition Ch1: Inductor point, Ch2:Ldrv, Ch3:OCSet The value of RSET should be checked in an actual circuit to ensure that the over-current protection circuit activates as expected. The IR3629 current limit is designed primarily as a disaster preventing, "no blow up" circuit, and does not operate as a precision current regulator. 10 IR3629/IR3629A MPbF Soft-Start Programming Application Information Design Example: The following example is a typical application for IR3629. The application circuit is shown on page 18. Vin=12V,(13.2V, max ) Vo=1.5V Io=12 A ΔVo≤30 mV(output voltage ripple) Fs=600 kHz The soft-start timing can be programmed by selecting the soft-start capacitance value. The start-up time of the converter can be calculated by using: CSS ≅ 20μA * Tstart --(1) Where Tstart is the desired start-up time (ms). For a start-up time of 10ms, the soft-start capacitor will be 0.2uF. Choose a ceramic capacitor at 0.22uF. Vc supply for single input voltage Output Voltage Programming Output voltage is programmed by reference voltage and external voltage divider. The Fb pin is the inverting input of the error amplifier, which is internally referenced to 0.6V. The divider is ratioed to provide 0.6V at the Fb pin when the output is at its desired value. The output voltage is defined by using the following equation: ⎛ R ⎞ Vo = Vref ∗ ⎜⎜1 + 8 ⎟⎟ R9 ⎠ ⎝ --( 4 ) When an external resistor divider is connected to the output as shown in figure 10. VOUT IR3629 IR3624 R8 Fb R9 Fig. 10: Typical application of the IR3629 for programming the output voltage To drive the high side switch, it is necessary to supply a gate voltage at least 4V greater than the bus voltage. This is achieved by using a charge pump configuration as shown in figure 11. This method is simple and inexpensive. The operation of the circuit is as follows: when the lower MOSFET is turned on, the capacitor (C1) is pulled down to ground and charges, up to VBUS value, through the diode (D1). The bus voltage will be added to this voltage when the upper MOSFET turns on in the next cycle, and providing supply voltage (Vc) through diode (D2). Vc is approximately: VC ≅ 2 ∗Vbus − (VD1 + VD2 ) --(6 ) A capacitors in the range of 0.1uF is generally adequate for most applications. Fast recovery diodes must be used to minimize the amount of charge fed back from the charge pump capacitor into VBUS. The diodes need to be able to block the full power rail voltage, which is seen when the high-side MOSFET is switched on. For lowvoltage applications, schottky diodes can be used to minimize forward drop. VBUS Equation (4) can be rewritten as: D1 C3 D2 ⎛ V R9 = R8 ∗ ⎜⎜ ref ⎝ V O−Vref ⎞ ⎟⎟ ⎠ For the calculated values of R8 and R9 see feedback compensation section. VBUS Vc --( 5 ) C2 C1 Q1 L IR3629/29A IR3624 HDrv Q2 Fig. 11: Charge pump circuit to generate Vc voltage 11/26/2007 11 IR3629/IR3629A MPbF Input Capacitor Selection The ripple current generated during the on time of upper the MOSFET should be provided by the input capacitor. The RMS value of this ripple is expressed by: IRMS = Io ∗ D ∗ (1 − D ) --(7 ) V D= o Vin Where: D is the Duty Cycle IRMS is the RMS value of the input capacitor current. Io is the output current. For Io=10A and D=0.125, the IRMS=3.3A. Ceramic capacitors are recommended due to their peak current capabilities, they also feature low ESR and ESL at higher frequency which enables better efficiency. Use 4x22uF, 16V ceramic capacitors from Panasonic. If Δi ≈ 37%(Io ) , then the output inductor will be: L = 0.6uH The MPL104-0R6 from Delta provides a compact, low profile inductor suitable for this application. Output Capacitor Selection The voltage ripple and transient requirements determine the output capacitors type and values. The criteria is normally based on the value of the Effective Series Resistance (ESR). However the actual capacitance value and the Equivalent Series Inductance (ESL) are other contributing components. These components can be described as: ΔVo = ΔVo(ESR) + ΔVo(ESL) + ΔVo(C ) ΔVo(ESR) = ΔIL * ESR - -(9) ⎛Vin ⎞ ⎟ * ESL ⎝L⎠ ΔVo(ESL) = ⎜ Inductor Selection The inductor is selected based on output power, operating frequency and efficiency requirements. A low inductor value causes large ripple current, resulting in the smaller size, faster response to a load transient but poor efficiency and high output noise. Generally, the selection of the inductor value can be reduced to the desired maximum ripple current in the inductor ( Δi ) . The optimum point is usually found between 20% and 50% ripple of the output current. For the buck converter, the inductor value for the desired operating ripple current can be determined using the following relation: Vin − Vo = L ∗ Δi 1 ; Δt = D ∗ Fs Δt Where:L = (Vin − Vo ) ∗ Vo Vin ∗ Δi * Fs Vin = Maximum input voltage Vo = Output Voltage Δi = Inductor ripple current F s= Switching frequency Δt = Turn on time D = Duty cycle 11/26/2007 --(8 ) ΔVo(C ) = ΔIL 8 * Co * Fs ΔVo = Output voltage ripple ΔIL = Inductor ripple current Since the output capacitor has a major role in the overall performance of the converter and determines the result of transient response, selection of the capacitor is critical. The IR3629 can perform well with all types of capacitor. As a rule, the capacitor must have low enough ESR to meet output ripple and load transient requirements. The goal for this design is to meet the voltage ripple requirement in the smallest possible capacitor size. Therefore a ceramic capacitor is selected due to low ESR and small size. Five of the Panasonic ECJ2FB0J226M (22uF, 6.3V, X5R and EIA 0805 case size) is a good choice. In the case of tantalum or low ESR electrolytic capacitors, the ESR dominates the output voltage ripple, equation (9) can be used to calculate the required ESR for the specific voltage ripple. 12 IR3629/IR3629A MPbF Power MOSFET Selection The IR3629 uses two N-Channel MOSFETs per channel. The selection criteria to meet power transfer requirements are based on maximum drain-source voltage (VDSS), gate-source drive voltage (Vgs), maximum output current, Onresistance RDS(on), and thermal management. The MOSFET must have a maximum operating voltage (VDSS) exceeding the maximum input voltage (Vin). The gate drive requirement is almost the same for both MOSFETs. A logic-level transistor can be used and caution should be taken with devices at very low gate threshold voltage (Vgs) to prevent undesired turn-on of the complementary MOSFET, which results in a shoot-through current. The total power dissipation for MOSFETs includes conduction and switching losses. For the Buck converter the average inductor current is equal to the DC load current. The conduction loss is defined as: switching losses in a synchronous Buck converter. The synchronous MOSFET turns on under zero voltage conditions, therefore, the turn on losses for synchronous MOSFET can be neglected. With a linear approximation, the total switching loss can be expressed as: Psw = Vds(off ) tr + tf * * Iload - - - (10) 2 T Where: V ds(off) = Drain to source voltage at the off time tr = Rise time tf = Fall time T = Switching period Iload = Load current The switching time waveforms is shown in figure12. VDS 90% 2 Pcond = (upper switch)= Iload ∗ Rds(on) ∗ D ∗ ϑ 2 Pcond = (lower switch)= Iload ∗ Rds(on) ∗ (1 − D) ∗ϑ ϑ = Rds(on) temperature dependency The RDS(on) temperature dependency should be considered for the worst case operation. This is typically given in the MOSFET datasheet. Ensure that the conduction losses and switching losses do not exceed the package ratings or violate the overall thermal budget. For this design, the IRF7823 is selected for control FET and IRF7832Z is selected for the synchronous FET. These devices provide low on resistance in a cost effective SO8 package. The MOSFETs have the following data: ControlFET(IRF7823): Vds = 30V,Qg = 14nC SyncFET(IRF7832Z): Vds = 30V,Qg = 45nC Rds(on) = 8.7mΩ @Vgs = 10V Rds(on) = 3.8mΩ @Vgs = 10V The conduction losses will be: Pcon=0.44W. The switching loss is more difficult to calculate, even though the switching transition is well understood. The reason is the effect of the parasitic components and switching times during the switching procedures such as turn-on / turnoff delays and rise and fall times. The control MOSFET contributes to the majority of the 11/26/2007 10% VGS td(ON) tr td(OFF) tf Fig. 12: switching time waveforms From IRF7832Z data sheet: tr = 13ns tf = 14ns These values are taken under a certain test condition. For more details please refer to the IRF7832Z data sheet. By using equation (10), we can calculate the switching losses. Psw=0.74W The reverse recovery loss is also another contributing factor in control FET switching losses. This is equivalent to extra current required to remove the minority charges from the synchronous FET. The reverse recovery loss can be expressed as: PQrr = Qrr*trr*Fs Qrr : Reverse Recovery Charge trr : Reverse Recovery Time Fs: Switching Frequency 13 IR3629/IR3629A MPbF Feedback Compensation The IR3629 is a voltage mode controller. The control loop is a single voltage feedback path including error amplifier and error comparator. To achieve fast transient response and accurate output regulation, a compensation circuit is necessary. The goal of the compensation network is to provide a closed-loop transfer function with the highest 0dB crossing frequency and adequate phase margin (greater than 45o). The output LC filter introduces a double pole, – 40dB/decade gain slope above its corner resonant frequency, and a total phase lag of 180o (see figure 13). The resonant frequency of the LC filter is expressed as follows: FLC = 1 - - - (11) 2 ∗ π Lo ∗ Co Phase 0 0dB -180 E/A R9 Comp Ve C4 VREF R3 CPOLE Gain(dB) H(s) dB Frequency Fig. 14: TypeII compensation network and its asymptotic gain plot The transfer function (Ve/Vo) is given by: ⎛ R9 ⎞ 1 + sR3C4 ⎟* H(s) = ⎜⎜ gm * - - - (13) R9 + R8 ⎟⎠ sC4 ⎝ [H(s)] = ⎛⎜⎜ g FLC ⎝ Frequency Fig. 13: Gain and Phase of LC filter The IR3629/29A’s error amplifier is a differentialinput transconductance amplifier. The output is available for DC gain control or AC phase compensation. The error amplifier can be compensated either in type II or type III compensation. When it is used in type II compensation the transconductance properties of the error amplifier become evident and can be used to cancel one of the output filter poles. This will be accomplished with a series RC circuit from Comp pin to ground as shown in figure 14. This method requires the output capacitor should have enough ESR to satisfy stability requirements. In general the output capacitor’s ESR generates a zero typically at 5kHz to 50kHz which is essential for an acceptable phase margin. 11/26/2007 Fb The (s) indicates that the transfer function varies as a function of frequency. This configuration introduces a gain and zero, expressed by: -40dB/decade FLC Frequency R8 FZ Figure 13 shows gain and phase of the LC filter. Since we already have 180o phase shift from the output filter a lone , the system risks being unstable. Gain The ESR zero of the output capacitor expressed as follows: 1 FESR = - - - (12) 2 ∗ π * ESR * Co VOUT Fz = m * R9 ⎞ ⎟ * R3 - - - (14) R9 + R8 ⎟⎠ 1 2π * R3 * C4 - - - (15) The gain is determined by the voltage divider and error amplifier’s transconductance gain. First select the desired zero-crossover frequency (Fo): Fo > FESR and Fo ≤ (1/5 ~ 1/10) * Fs Use the following equation to calculate R3: R3 = Vosc * Fo * FESR * (R8 + R9 ) * 1.28 2 Vin * FLC * R9 * gm - - - (15A) Where: Vin = Maximum Input Voltage Vosc = Oscillator Ramp Voltage Fo = Crossover Frequency FESR = Zero Frequency of the Output Capacitor FLC = Resonant Frequency of the Output Filter R8 and R9 = Feedback Resistor Dividers gm = Error Amplifier Transconductance 1.28 = Empirical number to compensate thermal, process variations and components tolerances 14 IR3629/IR3629A MPbF To cancel one of the LC filter poles, place the zero before the LC filter resonant frequency pole: VOUT ZIN Fz = 75%FLC C7 1 Fz = 0.75 * 2π Lo * Co - - - (16) Using equations (15) and (16) to calculate C9. One more capacitor is sometimes added in parallel with C4 and R3. This introduces one more pole which is mainly used to suppress the switching noise. The additional pole is given by: 1 FP = C *C 2π * R3 * 4 POLE C4 + CPOLE 1 1 π * R3 * Fs − C4 ≅ R3 R10 1 π * R 3 * Fs For a general solution for unconditional stability for any type of output capacitors, in a wide range of ESR values we should implement local feedback with a compensation network (type III). The typically used compensation network for voltage-mode controller is shown in figure 15. In such configuration, the transfer function is given by: C4 R8 Zf Fb R9 E/A Comp H(s) dB FZ2 FP2 FP3 As known, the transconductance amplifier has a high impedance (current source) output, therefore, consideration should be taken when loading the error amplifier output. It may exceed its source/sink output current capability, so that the amplifier will not be able to swing its output voltage over the necessary range. The compensation network has three poles and two zeros and they are expressed as follows: FP1 = 0 FP 2 = 1 2π * R10 * C7 FP 3 = The error amplifier gain is independent of the transconductance under the following condition: Fz1 = 1 2π * R3 * C4 Fz 2 = 1 1 ≅ 2π * C7 * (R8 + R10 ) 2π * C7 * R8 - - - (17) Frequency Fig.15: Compensation network with local feedback and its asymptotic gain plot Ve 1 − g m Zf = Vo 1 + g m ZIN gm * Z f >> 1 and gm * Z in >> 1 Ve VREF Gain(dB) FZ1 The pole sets to one half of the switching frequency which results in the capacitor CPOLE: CPOLE = C3 1 1 ≅ ⎛ C * C3 ⎞ 2π * R3 * C3 ⎟⎟ 2π * R3 ⎜⎜ 4 ⎝ C4 + C3 ⎠ Cross over frequency is expressed as: By replacing Zin and Zf according to figure 15, the transfer function can be expressed as: H (s ) = Fo = R3 * C7 * Vin 1 * Vosc 2π * Lo * Co (1 + sR3C4 ) * [1 + sC7 (R8 + R10 )] 1 * sR8 (C4 + C3 ) ⎡ ⎛ C4 * C3 ⎞⎤ ⎟⎟⎥ * (1 + sR10C7 ) ⎢1 + sR3 ⎜⎜ ⎝ C4 + C3 ⎠⎦ ⎣ 11/26/2007 15 IR3629/IR3629A MPbF Based on the frequency of the zero generated by the output capacitor and its ESR versus crossover frequency, the compensation type can be different. The table below shows the compensation types and location of the crossover frequency. Compensator type FESR vs. Fo Output capacitor TypII(PI) FLC<FESR<Fo<Fs/2 Electrolytic , Tantalum TypeIII(PID) Method A FLC<Fo<FESR<Fs/2 Tantalum, ceramic TypeIII(PID) Method B FLC<Fo<Fs/2<FESR Ceramic The following design rules will give a crossover frequency approximately one-tenth of the switching frequency. The higher the band width, the potentially faster the load transient response. The DC gain will be large enough to provide high DC-regulation accuracy (typically -5dB to -12dB). The phase margin should be greater than 45o for overall stability. Desired Phase Margin: Θmax = π 3 1 SinΘ FZ 2 = Fo * 1 + SinΘ FZ 2 = 16kHz Table1- The compensation type and location of FESR versus Fo 1 + SinΘ 1 SinΘ FP 2 = 224kHz The details of these compensation types are discussed in application note AN-1043 which can be downloaded from IR’s website at www.irf.com. Select : FZ1 = 0.5 * FZ 2 and FP3 = 0.5 * Fs For this design we have: R3 ≥ Vin=12V Vo=0.9V Vosc=1.25V Vref=0.6V gm=1000umoh Lo=0.56uH Co=5x22uF, ESR=2mOhm Note: Use 15uF instead of 22uF for calculation, this is due to derating of ceramic capacitor Fs=600kHz These result to: FLC=24.6kHz FESR=1MHz Fs/2=300kHz Select crossover frequency: FP 2 = Fo * 2 ; R ≥ 2KΩ; Select : R3 = 10KΩ gm 3 Calculate C4 , C3 and C7 : C4 = 1 ; C = 1.98nF, Select : C4 = 2.2nF 2π * FZ1 * R 3 4 C3 = 1 ; C = 65.8 pF, Select : C3 = 12pF 2π * FP 3 * R3 3 C7 = 2π * Fo * Lo * Co * Vosc * 1.28 ; C7 = 0.22nF, R3 * Vin Select : C7 = 0.22nF Calculate R10 , R8 and R9 : Fo < FESR and Fo ≤ (1/5 ~ 1/10) * Fs R10 = Fo=60kHz Since: FLC<Fo<Fs/2<FESR, typeIII method B is selected to place the pole and zeros. 11/26/2007 1 ; R = 3.23KΩ, Select : R10 = 3.24KΩ 2π * C7 * FP 2 10 R8 = 1 2π * C7 * FZ 2 R9 = Vref * R8 ; R9 = 27.47KΩ, Select : R9 = 27.4KΩ Vo Vref R10 ; R8 = 41.76KΩ, Select : R8 = 42.20KΩ 16 IR3629/IR3629A MPbF Programming the Current-Limit The Current-Limit threshold can be set by connecting a resistor (RSET) from the drain of the low-side MOSFET to the OCSet pin. The resistor can be calculated by using equation (3). The RDS(on) has a positive temperature coefficient and it should be considered for the worst case operation. This resistor must be placed close to the IC, place a small ceramic capacitor from this pin to ground for noise rejection purposes. ISET = IL( critical) = ROCSet ∗ IOCSet RDS( on ) --(3 ) RDS( on ) = 3.8 mΩ *1.5 = 5.7 mΩ ISET Io( LIM ) = 12 A *1.5 = 18 A (50% over nominal output current) ROCSet = 5.13KΩ Select R7 = 5.23KΩ Setting the Power Good Threshold Power Good threshold can be programmed by using two external resistors (R1, R2 in figure 16). The following formulas can be used to set the threshold: R2 = 0.38V *R1 0.9*Vout − 0.38V --(18 ) Where; 0.38V is reference of the internal comparator 0.9*Vout is selectable threshold for power good, for this design it is 1.35V. Layout Consideration The layout is very important when designing high frequency switching converters. Poor layout will affect noise pickup and can cause a good design to perform with less than expected results. Start to place the power components, making all the connection in the top layer with wide, copper filled areas. The inductor, output capacitors and the MOSFETS should be as close to each other as possible. This helps to reduce the EMI radiated by the power traces due to the high switching currents through them. Place input capacitor very close to the drain of the high-side MOSFET, to reduce the ESR replace the single input capacitor with two parallel units. The feedback part of the system should be kept away from the inductor and other noise sources. The critical bypass components such as capacitors for Vcc and Vc should be close to the respective pins. It is important to place the feedback components including feedback resistors and compensation components close to Fb and Comp pins. In a multilayer PCB use one layer as a power ground plane and have a control circuit ground (analog ground), to which all signals are referenced. The goal is to localize the high current path to a separate loop that does not interfere with the more sensitive analog control function. These two grounds must be connected together on the PC board layout at a single point. The MLPD is a thermally enhanced package. Based on thermal performance it is recommended to use 4-layers PCB. To effectively remove heat from the device the exposed pad should be connected to ground plane using vias. Select R1=10KOhm Using (18): R2=3.91KOhm Select R2=3.92K Use a pull up resistor (4.99K) from PGood pin to Vcc. 11/26/2007 17 IR3629/IR3629A MPbF Fig.16: Application circuit for 12V to 1.5V 11/26/2007 18 IR3629/IR3629A MPbF PCB Metal and Components Placement The lead land width should be equal to the nominal part lead width. The minimum lead to lead spacing should be ≥ 0.2mm to minimize shorting. The lead land length should be equal to maximum part lead length + 0.3 mm outboard extension + 0.05mm inboard extension. The outboard extension ensures a large and inspectable toe fillet, and the inboard extension will accommodate any part misalignment and ensure a fillet. The center pad land length and width should be equal to maximum part pad length and width. However, the minimum metal to metal spacing should be ≥ 0.17mm for 2 oz. Copper (≥ 0.1mm for 1 oz. Copper and ≥ 0.23mm for 3 oz. Copper). Two 0.30mm diameter via should be placed in the center of the pad land and connected to ground to minimize the noise effect on the IC. 11/26/2007 19 IR3629/IR3629A MPbF Solder Resist The solder resist should be pulled away from the metal lead lands by a minimum of 0.06mm. The solder resist mis-alignment is a maximum of 0.05mm and it is recommended that the lead lands are all Non Solder Mask Defined (NSMD). Therefore pulling the S/R 0.06mm will always ensure NSMD pads. The minimum solder resist width is 0.13mm. At the inside corner of the solder resist where the lead land groups meet, it is recommended to provide a fillet so a solder resist width of ≥ 0.17mm remains. The land pad should be Non Solder Mask Defined (NSMD), with a minimum pullback of the solder resist off the copper of 0.06mm to accommodate solder resist mis-alignment. Ensure that the solder resist in-between the lead lands and the pad land is ≥ 0.15mm due to the high aspect ratio of the solder resist strip separating the lead lands from the pad land. Each via in the land pad should be tented or plugged from bottom boardside with solder resist. 11/26/2007 20 IR3629/IR3629A MPbF Stencil Design The stencil apertures for the lead lands should be approximately 80% of the area of the lead lands. Reducing the amount of solder deposited will minimize the occurrence of lead shorts. Since for 0.5mm pitch devices the leads are only 0.25mm wide, the stencil apertures should not be made narrower; openings in stencils < 0.25mm wide are difficult to maintain repeatable solder release. The stencil lead land apertures should therefore be shortened in length by 80% and centered on the lead land. The land pad aperture should deposit approximately 50% area of solder on the center pad. If too much solder is deposited on the center pad the part will float and the lead lands will be open. The maximum length and width of the land pad stencil aperture should be equal to the solder resist opening minus an annular 0.2mm pull back to decrease the incidence of shorting the center land to the lead lands when the part is pushed into the solder paste. 11/26/2007 21 IR3629/IR3629A MPbF (IR3629/IR3629A M) MLPD Package 3x4-12Lead D E/2 E S Y M B O L A A3 SEATING PLANE A1 D2 E2 Terminal 1 Identifier A A1 A3 b D2 D E E2 L e N ND VGED-4 MILLIMETERS MIN NOM MAX 0.80 0.90 1.00 0.00 0.02 0.05 0.20 REF 0.18 0.25 0.30 INCHES NOM MAX .035 .039 .0008 .0019 .008 REF .0118 .0071 .0096 3.0 .118 3.70 _ 4.00 BSC 3.00 BSC 1.40 _ 1.80 0.30 0.40 0.50 0.50 PITCH 12 6 MIN .032 .000 _ .145 .157 BSC .118 BSC .070 .055 _ .012 .019 .016 .020 PITCH 10 6 Leads on 2 sides e b L (ND-1) x e TAPE & REEL ORIENTATION Figure A 11/26/2007 22 IR3629/IR3629A MPbF (IR3629M) MLPD Package 3x4-12Lead D E/2 E S Y M B O L A A3 A A1 A3 b SEATING PLANE D2 D E E2 L e N ND A1 D2 E2 Terminal 1 Identifier VEED-5 MILLIMETERS MIN NOM MAX 0.80 0.90 1.00 0.00 0.02 0.05 0.20 REF 0.18 0.25 0.30 INCHES NOM MAX .035 .039 .0008 .0019 .008 REF .0118 .0071 .0098 2.20 .087 2.70 _ 3.00 BSC 3.00 BSC 1.40 _ 1.75 0.30 0.40 0.50 0.50 PITCH 10 5 MIN .032 .000 _ .106 .118 BSC .118 BSC .068 .055 _ .012 .019 .016 .020 PITCH 10 5 Leads on 2 sides e b L (ND-1) x e TAPE & REEL ORIENTATION 1 1 1 Figure A IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105 TAC Fax: (310) 252-7903 This product has been designed and qualified for the Industrial market. Visit us at www.irf.com for sales contact information Data and specifications subject to change without notice. 11/2007 11/26/2007 23