Data Sheet No. PD94173 revD IRU3037/IRU3037A & (PbF) 8-PIN SYNCHRONOUS PWM CONTROLLER DESCRIPTION FEATURES Synchronous Controller in 8-Pin Package Operating with single 5V or 12V supply voltage Internal 200KHz Oscillator (400KHz for IRU3037A) Soft-Start Function Fixed Frequency Voltage Mode 500mA Peak Output Drive Capability Protects the output when control FET is shorted SOIC 8-Lead also available LEAD-FREE The IRU3037 controller IC is designed to provide a low cost synchronous Buck regulator for on-board DC to DC converter applications. With the migration of today’s ASIC products requiring low supply voltages such as 1.8V and lower, together with currents in excess of 3A, traditional linear regulators are simply too lossy to be used when input supply is 5V or even in some cases with 3.3V input supply. The IRU3037 together with dual N-channel MOSFETs such as IRF7313, provide a low cost solution for such applications. This device features an internal 200KHz oscillator (400KHz for "A" version), under-voltage lockout for both Vcc and Vc supplies, an external programmable soft-start function as well as output under-voltage detection that latches off the device when an output short is detected. APPLICATIONS DDR memory source sink Vtt application Low cost on-board DC to DC such as 5V to 3.3V, 2.5V or 1.8V Graphic Card Hard Disk Drive TYPICAL APPLICATION 5V 12V C4 1uF C3 1uF Vcc C9 2200pF C2 10TPB100M, 100uF, 55mΩ 1uH C1 47uF Vc HDrv C8 0.1uF L1 SS/SD U1 IRU3037 LDrv Q1 1/2 of IRF7313 L2 D05022P-562, 5.6uH, 5.3A Q2 1/2 of IRF7313 1.5V/5A C7 2x 6TPC150M, 150uF, 40mΩ R3 Comp Fb Gnd 249, 1% R5 1.24K, 1% R4 24k Figure 1 - Typical application of IRU3037 or IRU3037A. PACKAGE ORDER INFORMATION TA (°C) 0 To 70 0 To 70 0 To 70 0 To 70 DEVICE IRU3037CF IRU3037CS IRU3037ACF IRU3037ACS LEADFREE DEVICE PACKAGE IRU3037CFPbF 8-Pin Plastic TSSOP (F) IRU3037CSPbF 8-Pin Plastic SOIC NB (S) IRU3037ACFPbF 8-Pin Plastic TSSOP (F) IRU3037ACSPbF 8-Pin Plastic SOIC NB (S) www.irf.com FREQUENCY 200KHz 200KHz 400KHz 400KHz 1 IRU3037/IRU3037A & (PbF) ABSOLUTE MAXIMUM RATINGS Vcc Supply Voltage .................................................. 25V Vc Supply Voltage ...................................................... 30V (not rated for inductive load) Storage Temperature Range ...................................... -65°C To 150°C Operating Junction Temperature Range ..................... 0°C To 125°C CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. PACKAGE INFORMATION 8-PIN PLASTIC TSSOP (F) Fb 1 Vcc 2 8-PIN PLASTIC SOIC (S) 8 SS/SD Fb 1 8 SS/SD 7 Comp Vcc 2 7 Comp LDrv 3 6 Vc LDrv 3 6 Vc Gnd 4 5 HDrv Gnd 4 5 HDrv θJA=160°C/W (Also available LEAD-FREE) θJA=124°C/W ELECTRICAL SPECIFICATIONS Unless otherwise specified, these specifications apply over Vcc=5V, Vc=12V and TA=0 to 70°C. Typical values refer to TA=25°C. Low duty cycle pulse testing is used which keeps junction and case temperatures equal to the ambient temperature. PARAMETER Reference Voltage Fb Voltage Fb Voltage Line Regulation UVLO UVLO Threshold - Vcc UVLO Hysteresis - Vcc UVLO Threshold - Vc UVLO Hysteresis - Vc UVLO Threshold - Fb UVLO Hysteresis - Fb Supply Current Vcc Dynamic Supply Current Vc Dynamic Supply Current Vcc Static Supply Current Vc Static Supply Current Soft-Start Section Charge Current 2 SYM V FB LREG TEST CONDITION IRU3037 IRU3037A 5<Vcc<12 MIN TYP MAX UNITS 1.225 0.784 1.250 0.800 0.2 1.275 0.816 0.35 V % 4.2 0.25 3.3 0.2 0.6 0.4 0.1 4.4 UVLO Vcc Supply Ramping Up 4.0 UVLO Vc Supply Ramping Up 3.1 UVLO Fb Fb Ramping Down (IRU3037) (IRU3037A) 0.4 0.3 Dyn Icc Dyn Ic ICCQ ICQ SSIB 3.5 0.8 0.5 V V V V V V Freq=200KHz, CL=1500pF Freq=200KHz, CL=1500pF SS=0V SS=0V 2 2 1 0.5 5 7 3.3 1 8 10 6 4.5 mA mA mA mA SS=0V -10 -20 -30 µA www.irf.com IRU3037/IRU3037A & (PbF) PARAMETER Error Amp Fb Voltage Input Bias Current Fb Voltage Input Bias Current Transconductance Oscillator Frequency SYM Ramp-Amplitude Voltage Output Drivers Rise Time Fall Time Dead Band Time Max Duty Cycle Min Duty Cycle V RAMP IFB1 IFB2 TEST CONDITION Tr Tf IRU3037 IRU3037A TOFF MAX UNITS 410 -0.1 -64 600 830 µA µA µmho 180 345 1.225 200 400 1.25 220 440 1.275 KHz 50 85 0 50 50 150 90 0 100 100 250 95 ns ns ns % % CL=1500pF CL=1500pF TDB TON TYP SS=3V, Fb=1V SS=0V, Fb=1V gm Freq MIN Fb=1V, Freq=200KHz Fb=1.5V V PIN DESCRIPTIONS PIN# 1 PIN SYMBOL PIN DESCRIPTION Fb This pin is connected directly to the output of the switching regulator via resistor divider to provide feedback to the Error amplifier. 2 Vcc This pin provides biasing for the internal blocks of the IC as well as power for the low side driver. A minimum of 1µF, high frequency capacitor must be connected from this pin to ground to provide peak drive current capability. 3 LDrv Output driver for the synchronous power MOSFET. 4 Gnd This pin serves as the ground pin and must be connected directly to the ground plane. A high frequency capacitor (0.1 to 1µF) must be connected from V5 and V12 pins to this pin for noise free operation. 5 HDrv Output driver for the high side power MOSFET. Connect a diode, such as BAT54 or 1N4148, from this pin to ground for the application when the inductor current goes negative (Source/ Sink), soft-start at no load and for the fast load transient from full load to no load. 6 Vc This pin is connected to a voltage that must be at least 4V higher than the bus voltage of the switcher (assuming 5V threshold MOSFET) and powers the high side output driver. A minimum of 1µF, high frequency capacitor must be connected from this pin to ground to provide peak drive current capability. 7 Comp Compensation pin of the error amplifier. An external resistor and capacitor network is typically connected from this pin to ground to provide loop compensation. 8 SS / SD This pin provides soft-start for the switching regulator. An internal current source charges an external capacitor that is connected from this pin to ground which ramps up the output of the switching regulator, preventing it from overshooting as well as limiting the input current. The converter can be shutdown by pulling this pin below 0.5V. www.irf.com 3 IRU3037/IRU3037A & (PbF) BLOCK DIAGRAM Vcc 3V Bias Generator 1.25V 0.2V POR 4.0V 3V 0.2V Vc 20uA 3.5V 6 Vc 64uA Max SS/SD 8 Ct POR Oscillator 5 HDrv S 1.25V Q Error Comp 25K Fb 1 Error Amp R 2 Vcc Reset Dom 25K 3 LDrv 0.5V FbLo Comp 4 Gnd Comp 7 POR Figure 2 - Simplified block diagram of the IRU3037. THEORY OF OPERATION Introduction The IRU3037 is a fixed frequency, voltage mode synchronous controller and consists of a precision reference voltage, an error amplifier, an internal oscillator, a PWM comparator, 0.5A peak gate driver, soft-start and shutdown circuits (see Block Diagram). The output voltage of the synchronous converter is set and controlled by the output of the error amplifier; this is the amplified error signal from the sensed output voltage and the reference voltage. This voltage is compared to a fixed frequency linear sawtooth ramp and generates fixed frequency pulses of variable duty-cycle, which drives the two N-channel external MOSFETs.The timing of the IC is provided through an internal oscillator circuit which uses on-chip capacitor to set the oscillation frequency to 200 KHz (400 KHz for “A” version). Soft-Start The IRU3037 has a programmable soft-start to control the output voltage rise and limit the current surge at the start-up. To ensure correct start-up, the soft-start sequence initiates when the Vc and Vcc rise above their threshold (3.3V and 4.2V respectively) and generates 4 the Power On Reset (POR) signal. Soft-start function operates by sourcing an internal current to charge an external capacitor to about 3V. Initially, the soft-start function clamps the E/A’s output of the PWM converter. As the charging voltage of the external capacitor ramps up, the PWM signals increase from zero to the point the feedback loop takes control. Short-Circuit Protection The outputs are protected against the short-circuit. The IRU3037 protects the circuit for shorted output by sensing the output voltage (through the external resistor divider). The IRU3037 shuts down the PWM signals, when the output voltage drops below 0.6V (0.4V for IRU3037A). The IRU3037 also protects the output from over-voltaging when the control FET is shorted. This is done by turning on the sync FET with the maximum duty cycle. Under-Voltage Lockout The under-voltage lockout circuit assures that the MOSFET driver outputs remain in the off state whenever the supply voltage drops below set parameters. Lockout occurs if Vc or Vcc fall below 3.3V and 4.2V respectively. Normal operation resumes once Vc and Vcc rise above the set values. www.irf.com IRU3037/IRU3037A & (PbF) APPLICATION INFORMATION Design Example: The following example is a typical application for IRU3037, the schematic is Figure 18 on page 14. VIN = 5V VOUT = 3.3V IOUT = 4A ∆VOUT = 100mV fS = 200KHz tSTART = 75×Css (ms) ( R6 1+ R5 ) ---(1) When an external resistor divider is connected to the output as shown in Figure 3. VOUT IRU3037 R6 Fb R5 Figure 3 - Typical application of the IRU3037 for programming the output voltage. Equation (1) can be rewritten as: R6 = R5 × ( VV ---(2) Where: CSS is the soft-start capacitor (µF) Output Voltage Programming Output voltage is programmed by reference voltage and external voltage divider. The Fb pin is the inverting input of the error amplifier, which is internally referenced to 1.25V (0.8V for IRU3037A). The divider is ratioed to provide 1.25V at the Fb pin when the output is at its desired value. The output voltage is defined by using the following equation: VOUT = VREF × Soft-Start Programming The soft-start timing can be programmed by selecting the soft start capacitance value. The start up time of the converter can be calculated by using: OUT REF ) For a start-up time of 7.5ms, the soft-start capacitor will be 0.1µF. Choose a ceramic capacitor at 0.1µF. Shutdown The converter can be shutdown by pulling the soft-start pin below 0.5V. The control MOSFET turns off and the synchronous MOSFET turns on during shutdown. Boost Supply Vc To drive the high-side switch it is necessary to supply a gate voltage at least 4V greater than the bus voltage. This is achieved by using a charge pump configuration as shown in Figure 18. The capacitor is charged up to approximately twice the bus voltage. A capacitor in the range of 0.1µF to 1µF is generally adequate for most applications. In application, when a separate voltage source is available the boost circuit can be avoided as shown in Figure 1. Input Capacitor Selection The input filter capacitor should be based on how much ripple the supply can tolerate on the DC input line. The larger capacitor, the less ripple expected but consider should be taken for the higher surge current during the power-up. The IRU3037 provides the soft-start function which controls and limits the current surge. The value of the input capacitor can be calculated by the following formula: -1 CIN = Choose R5 = 1KΩ This will result to R6 = 1.65KΩ If the high value feedback resistors are used, the input bias current of the Fb pin could cause a slight increase in output voltage. The output voltage set point can be more accurate by using precision resistor. IIN × ∆t ∆V ---(3) Where: CIN is the input capacitance (µF) IIN is the input current (A) ∆t is the turn on time of the high-side switch (µs) ∆V is the allowable peak to peak voltage ripple (V) www.irf.com 5 IRU3037/IRU3037A & (PbF) Assuming the following: ∆V = 1%(VIN), Efficiency(η) = 90% 1 ∆t = D × ∆t = 3.3µs fS VO × IO IIN = η × VIN IIN = 2.93A By using equation (3), CIN = 193.3µF For higher efficiency, low ESR capacitor is recommended. Choose two 100µF capacitors. The Sanyo TPB series PosCap capacitor 100µF, 10V with 55mΩ ESR is a good choice. Output Capacitor Selection The criteria to select the output capacitor is normally based on the value of the Effective Series Resistance (ESR). In general, the output capacitor must have low enough ESR to meet output ripple and load transient requirements, yet have high enough ESR to satisfy stability requirements. The ESR of the output capacitor is calculated by the following relationship: ESR ≤ ∆VO ∆IO ---(4) Where: ∆VO = Output Voltage Ripple ∆IO = Output Current ∆VO=100mV and ∆IO=4A Results to ESR=25mΩ If ∆i = 20%(IO), then the output inductor will be: L = 7µH The Toko D124C series provides a range of inductors in different values, low profile suitable for large currents, 10µH, 4.2A is a good choice for this application. This will result to a ripple approximately 14% of output current. Power MOSFET Selection The IRU3037 uses two N-Channel MOSFETs. The selections criteria to meet power transfer requirements is based on maximum drain-source voltage (VDSS), gatesource drive voltage (VGS), maximum output current, Onresistance RDS(ON) and thermal management. The MOSFET must have a maximum operating voltage (VDSS) exceeding the maximum input voltage (VIN). The Sanyo TPC series, PosCap capacitor is a good choice. The 6TPC150M 150µF, 6.3V has an ESR 40mΩ. Selecting two of these capacitors in parallel, results to an ESR of ≅ 20mΩ which achieves our low ESR goal. The capacitor value must be high enough to absorb the inductor's ripple current. The larger the value of capacitor, the lower will be the output ripple voltage. Inductor Selection The inductor is selected based on output power, operating frequency and efficiency requirements. Low inductor value causes large ripple current, resulting in the smaller size, but poor efficiency and high output noise. Generally, the selection of inductor value can be reduced to desired maximum ripple current in the inductor (∆i). The optimum point is usually found between 20% and 50% ripple of the output current. For the buck converter, the inductor value for desired operating ripple current can be determined using the following relation: 6 ∆i VOUT 1 ; ∆t = D× ; D = ∆t VIN fS VOUT L = (VIN - VOUT)× ---(5) VIN×∆i×fS Where: VIN = Maximum Input Voltage VOUT = Output Voltage ∆i = Inductor Ripple Current fS = Switching Frequency ∆t = Turn On Time D = Duty Cycle VIN - VOUT = L× The gate drive requirement is almost the same for both MOSFETs. Logic-level transistor can be used and caution should be taken with devices at very low VGS to prevent undesired turn-on of the complementary MOSFET, which results a shoot-through current. The total power dissipation for MOSFETs includes conduction and switching losses. For the Buck converter the average inductor current is equal to the DC load current. The conduction loss is defined as: 2 PCOND (Upper Switch) = ILOAD × RDS(ON) × D × ϑ 2 PCOND (Lower Switch) = ILOAD × RDS(ON) × (1 - D) × ϑ ϑ = RDS(ON) Temperature Dependency The RDS(ON) temperature dependency should be considered for the worst case operation. This is typically given in the MOSFET data sheet. Ensure that the conduction losses and switching losses do not exceed the package ratings or violate the overall thermal budget. www.irf.com IRU3037/IRU3037A & (PbF) For this design, IRF7301 is a good choice. The device provides low on-resistance in a compact SOIC 8-Pin package. These values are taken under a certain condition test. For more detail please refer to the IRF7301 data sheet. By using equation (6), we can calculate the switching losses. The IRF7301 has the following data: PSW = 0.186W VDSS = 20V ID = 5.2A RDS(ON) = 0.05Ω The total conduction losses will be: P CON(TOTAL)=P CON(Upper Switch)+P CON(Lower Switch) 2 PCON(TOTAL) = ILOAD × RDS(ON) × ϑ ϑ = 1.5 according to the IRF7301 data sheet for 150)C junction temperature PCON(TOTAL) = 1.2W The switching loss is more difficult to calculate, even though the switching transition is well understood. The reason is the effect of the parasitic components and switching times during the switching procedures such as turn-on / turnoff delays and rise and fall times. With a linear approximation, the total switching loss can be expressed as: VDS(OFF) tr + tf × ILOAD × PSW = ---(6) T 2 Where: VDS(OFF) = Drain to Source Voltage at off time tr = Rise Time tf = Fall Time T = Switching Period ILOAD = Load Current Feedback Compensation The IRU3037 is a voltage mode controller; the control loop is a single voltage feedback path including error amplifier and error comparator. To achieve fast transient response and accurate output regulation, a compensation circuit is necessary. The goal of the compensation network is to provide a closed loop transfer function with the highest 0dB crossing frequency and adequate phase margin (greater than 45)). The output LC filter introduces a double pole, –40dB/ decade gain slope above its corner resonant frequency, and a total phase lag of 180) (see Figure 5). The Resonant frequency of the LC filter expressed as follows: FLC = 1 2π× ---(7) LO×CO Figure 5 shows gain and phase of the LC filter. Since we already have 180) phase shift just from the output filter, the system risks being unstable. Gain Phase 0) 0dB -40dB/decade The switching time waveform is shown in figure 4. VDS 90% FLC Frequency -180) FLC Frequency Figure 5 - Gain and phase of LC filter. 10% VGS td(ON) The IRU3037’s error amplifier is a differential-input transconductance amplifier. The output is available for DC gain control or AC phase compensation. tr td(OFF) tf Figure 4 - Switching time waveforms. From IRF7301 data sheet we obtain: tr = 42ns tf = 51ns The E/A can be compensated with or without the use of local feedback. When operated without local feedback the transconductance properties of the E/A become evident and can be used to cancel one of the output filter poles. This will be accomplished with a series RC circuit from Comp pin to ground as shown in Figure 6. www.irf.com 7 IRU3037/IRU3037A & (PbF) Note that this method requires that the output capacitor should have enough ESR to satisfy stability requirements. In general the output capacitor’s ESR generates a zero typically at 5KHz to 50KHz which is essential for an acceptable phase margin. The ESR zero of the output capacitor expressed as follows: 1 FESR = ---(8) 2π × ESR × Co VOUT R6 Fb E/A R5 Comp Ve C9 VREF R4 H(s) dB To cancel one of the LC filter poles, place the zero before the LC filter resonant frequency pole: FZ FZ ≅ 75%FLC Frequency Figure 6 - Compensation network without local feedback and its asymptotic gain plot. The transfer function (Ve / VOUT) is given by: ( R5 R6 + R5 For: VIN = 5V VOSC = 1.25V Fo = 30KHz FESR = 26.52KHz FLC = 2.9KHz R5 = 1K R6 = 1.65K gm = 600µmho This results to R4=104.4KΩ. Choose R4=105KΩ Gain(dB) H(s) = gm × Where: VIN = Maximum Input Voltage VOSC = Oscillator Ramp Voltage Fo = Crossover Frequency FESR = Zero Frequency of the Output Capacitor FLC = Resonant Frequency of the Output Filter R5 and R6 = Resistor Dividers for Output Voltage Programming gm = Error Amplifier Transconductance ) × 1 +sCsR C 4 9 ---(9) 9 FZ ≅ 0.75 × 1 2π LO × CO ---(13) For: Lo = 10µH Co = 300µF FZ = 2.17KHz R4 = 86.6KΩ Using equations (11) and (13) to calculate C9, we get: The (s) indicates that the transfer function varies as a function of frequency. This configuration introduces a gain and zero, expressed by: R5 |H(s)| = gm× × R4 ---(10) R6×R5 FZ = 1 2π×R4×C9 ---(11) The gain is determined by the voltage divider and E/A's transconductance gain. First select the desired zero-crossover frequency (Fo): Fo > FESR and FO ≤ (1/5 ~ 1/10)× fS Use the following equation to calculate R4: R4 = 8 1 VOSC Fo×FESR R5 + R6 × × × gm VIN FLC2 R5 C9 = 698pF Choose C9 = 680pF One more capacitor is sometimes added in parallel with C9 and R4. This introduces one more pole which is mainly used to supress the switching noise. The additional pole is given by: 1 FP = C9 × CPOLE 2π × R4 × C9 + CPOLE The pole sets to one half of switching frequency which results in the capacitor CPOLE: CPOLE = ---(12) www.irf.com 1 π×R4×fS - 1 C9 fS for FP << 2 ≅ 1 π×R4×fS IRU3037/IRU3037A & (PbF) For a general solution for unconditionally stability for any type of output capacitors, in a wide range of ESR values we should implement local feedback with a compensation network. The typically used compensation network for voltage-mode controller is shown in Figure 7. VOUT ZIN R7 Zf Fb E/A R5 Comp Ve VREF Gain(dB) H(s) dB FZ1 FZ2 FP2 FP3 FP3 = In such configuration, the transfer function is given by: 1 - gmZf Ve = VOUT 1 + gmZIN gmZIN >>1 ---(14) By replacing ZIN and Zf according to Figure 7, the transformer function can be expressed as: 1 × sR6(C12+C11) (1+sR7C11)×[1+sC10(R6+R8)] C12×C11 1+sR7 ×(1+sR8C10) C12+C11 [ ( ) C12×C11 2π×R7× C12+C11 ≅ 1 2π×R7×C12 1 2π×R7×C11 1 FZ2 = 2π×C10×(R6 + R8) ≅ 1 2π×C10×R6 Cross Over Frequency: VIN 1 FO = R7×C10× × VOSC 2π×Lo×Co Where: VIN = Maximum Input Voltage VOSC = Oscillator Ramp Voltage Lo = Output Inductor Co = Total Output Capacitors ---(15) The stability requirement will be satisfied by placing the poles and zeros of the compensation network according to following design rules. The consideration has been taken to satisfy condition (14) regarding transconductance error amplifier. 1) Select the crossover frequency: Fo < FESR and Fo ≤ (1/10 ~ 1/6)× fS The error amplifier gain is independent of the transconductance under the following condition: and 1 Frequency Figure 7 - Compensation network with local feedback and its asymptotic gain plot. H(s)= 1 2π×R8×C10 FZ1 = C11 R6 gmZf >> 1 FP2 = C12 C10 R8 FP1 = 0 ( )] As known, transconductance amplifier has high impedance (current source) output, therefore, consider should be taken when loading the E/A output. It may exceed its source/sink output current capability, so that the amplifier will not be able to swing its output voltage over the necessary range. 2) Select R7, so that R7 >> 2 gm 3) Place first zero before LC’s resonant frequency pole. FZ1 ≅ 75% FLC 1 C11 = 2π × FZ1 × R7 4) Place third pole at the half of the switching frequency. fS FP3 = 2 1 C12 = 2π × R7 × FP3 C12 > 50pF If not, change R7 selection. 5) Place R7 in (15) and calculate C10: The compensation network has three poles and two zeros and they are expressed as follows: C10 ≤ www.irf.com VOSC 2π × Lo × Fo × Co × VIN R7 9 IRU3037/IRU3037A & (PbF) 6) Place second pole at the ESR zero. FP2 = FESR 1 R8 = 2π × C10 × FP2 Check if R8 > 1 gm If R8 is too small, increase R7 and start from step 2. 7) Place second zero around the resonant frequency. FZ2 = FLC 1 R6 = - R8 2π × C10 × FZ2 8) Use equation (1) to calculate R5. VREF R5 = × R6 VOUT - VREF These design rules will give a crossover frequency approximately one-tenth of the switching frequency. The higher the band width, the potentially faster the load transient speed. The gain margin will be large enough to provide high DC-regulation accuracy (typically -5dB to 12dB). The phase margin should be greater than 45) for overall stability. Start to place the power components, make all the connection in the top layer with wide, copper filled areas. The inductor, output capacitor and the MOSFET should be close to each other as possible. This helps to reduce the EMI radiated by the power traces due to the high switching currents through them. Place input capacitor directly to the drain of the high-side MOSFET, to reduce the ESR replace the single input capacitor with two parallel units. The feedback part of the system should be kept away from the inductor and other noise sources, and be placed close to the IC. In multilayer PCB use one layer as power ground plane and have a control circuit ground (analog ground), to which all signals are referenced. The goal is to localize the high current path to a separate loop that does not interfere with the more sensitive analog control function. These two grounds must be connected together on the PC board layout at a single point. Figure 8 shows a suggested layout for the critical components, based on the schematic on page 14. PGnd PGnd C2A, B C1 Vin L1 Vout 8 IC Quiescent Power Dissipation Power dissipation for IC controller is a function of applied voltage, gate driver loads and switching frequency. The IC's maximum power dissipation occurs when the IC operating with single 12V supply voltage (Vcc=12V and Vc≅24V) at 400KHz switching frequency and maximum gate loads. Layout Consideration The layout is very important when designing high frequency switching converters. Layout will affect noise pickup and can cause a good design to perform with less than expected results. 10 www.irf.com 7 6 5 L2 Q1 1 D D D C 3 2 1 5 2 5 C4 6 PGnd Figures 9 and 10 show voltage vs. current, when the gate drivers loaded with 470pF, 1150pF and 1540pF capacitors. The IC's power dissipation results to an excessive temperature rise. This should be considered when using IRU3037A for such application. C7A, B PGnd R4 C9 7 3 Single Point Analog Gnd Connect to Power Ground plane 4 U1 IRU3037 4 3 2 C3 Analog Gnd R5 C8 8 1 R6 Analog Gnd Figure 8 - Suggested layout. (Topside shown only) IRU3037/IRU3037A & (PbF) TYPICAL PERFORMANCE CHARACTERISTICS IR U 3037A V cc vs. Icc TA = 25)C Icc (m A ) @ 470P F , 1150P F and 1540P F G ate Load 14 12 10 8 6 4 2 0 CLOAD=1540pF CLOAD=1150pF CLOAD=470pF 0 2 4 6 8 10 12 14 V cc (V ) Figure 9 - Vcc vs. Icc IRU3037A Vc vs. Ic TA = 25)C @470PF, 1150PF and 1540PF Gate Load 30 Ic (ma) 25 CLOAD=1540pF 20 CLOAD=1150pF 15 10 CLOAD=470pF 5 0 0 2 4 6 8 10 12 14 16 18 20 22 24 26 Vc (V) Figure 10 - Vc vs. Ic www.irf.com 11 IRU3037/IRU3037A & (PbF) TYPICAL PERFORMANCE CHARACTERISTICS IR U 3 0 3 7 O u tp u t V o lta g e IR U 3 0 3 7 O u tp u t F re q u e n c y 240 1 .3 230 1 .2 8 Max 220 Max 210 Volts Kilo Hertz 1 .2 6 200 1 .2 4 190 Min Min 180 1 .2 2 170 1 .2 160 -4 0 ° C 0°C O u tp u t Vo lta g e + 50 °C + 100°C S p e c M a x. -4 0 ° C + 150°C 0 °C S p e c M in . O s c illa tio n F r e q u e n c y Figure 11 - Output Voltage 92.0% 90.0% Percent Duty Cycle 88.0% 86.0% 84.0% 82.0% 80.0% -25°C 0°C +25°C +50°C +75°C +100°C +125°C Max Duty Cycle Figure 13 - Maximum Duty Cycle 12 + 10 0 °C S p ec Max. Figure 12 - Output Frequency IRU3037 Maximum Duty Cycle -40°C + 50°C www.irf.com +150°C S p e c M in . + 15 0 °C IRU3037/IRU3037A & (PbF) TYPICAL PERFORMANCE CHARACTERISTICS IR U 3 0 3 7 A O u tp u t V o lta g e IR U 3 0 3 7 A O u tp u t F re q u e n c y 820 460 Max 440 Max 810 420 800 Kilo Hertz 790 380 360 Min Min 780 340 770 320 760 300 -4 0 ° C -2 5 ° C 0°C + 25 °C O u tp u t Vo lta g e + 50 °C + 75 °C S p e c M a x. + 100°C + 150°C -4 0 ° C -2 5 ° C S p e c M in . 0 °C + 25°C O s c illa tio n F re q u e n c y Figure 14 - Output Voltage + 50°C + 75°C S p ec Max. + 10 0 °C + 15 0 °C S p e c M in . Figure 15 - Output Frequency IRU3037 / IRU3037A Transconductance ( GM ) 1000 900 800 700 600 micro Mho's milli Volts 400 500 400 300 200 100 0 -40°C -25°C 0°C +25°C Positive load GM +50°C +75°C +100°C Negative load GM Figure 16 - Transconductance www.irf.com 13 IRU3037/IRU3037A & (PbF) TYPICAL APPLICATION Single Supply 5V Input 5V D1 1N4148 D3 1N4148 1uH D2 1N4148 C3 1uF C4 1uF Vcc L1 C2 2x 10TPB100ML, 100uF, 55mΩ C5 0.1uF Vc Q1 1/2 of IRF7301 HDrv C8 0.1uF C9 680pF R4 105K SS/SD U1 L2 D05022P-103, 10uH, 4.3A IRU3037 Q2 1/2 of IRF7301 LDrv R6 Comp Fb 1.65K, 1% Gnd R5 1K, 1% Figure 17 - Typical application of IRU3037 in an on-board DC-DC converter using a single 5V supply. 14 C1 47uF Tantalum www.irf.com 3.3V @ 4A C7 2x 6TPC150M, 150uF, 40mΩ IRU3037/IRU3037A & (PbF) TYPICAL APPLICATION Dual Supply, 5V Bus and 12V Bias Input 5V L1 12V C4 1uF 1uH C2 10TPB100M, 100uF, 55mΩ , 1.5A rms C1 1uF C1 47uF 1.8V/1A IRU1206-18 Q1 1/2 of IRF7752 HDrv C7 0.1uF C8 2200pF C3 47uF Vc Vcc U1 IRU3037 SS/SD 2.5V/2A L2 CTX5-2P, 3.5uH @ 2.5A Q2 1/2 of IRF7752 LDrv C6 6TPB150M, 150uF, 55mΩ R1 Comp Fb 1K, 1% R3 1K 1% Gnd R2 14K L2 C6 CTX5-2P, 3.5uH @ 2.5A 6TPB150M, 150uF, 55mΩ (Qty 2) CTX10-5P, 5.7uH @ 2.5A 6TPB150M, 150uF, 55mΩ (Qty 1) C9 10TPB100M, 100uF, 55mΩ , 1.5A rms C10 1uF C11 1uF Vc Vcc Q3 1/2 of IRF7752 HDrv U2 IRU3037 SS/SD C13 0.1uF C14 2200pF R5 14K CTX5-1P, 3.4uH @ 2A Q4 1/2 of IRF7752 LDrv Comp C12 6TPB150M, 150uF, 55mΩ R4 Fb Gnd 3.3V/1.8A L3 1.65K, 1% R6 1K, 1% Figure 18 - Typical application of IRU3037 or IRU3037A in an on-board DC-DC converter providing the Core, GTL+, and Clock supplies for the Pentium II microprocessor. www.irf.com 15 IRU3037/IRU3037A & (PbF) TYPICAL APPLICATION 1.8V to 7.5V / 0.5A Boost Converter L1 1uH (CoilTronics UP2B-1R0) Vpwr (1.5V Min) C1 2x 68uF Vc/Vcc C5 1uF D1 1N5817 R1 20K Q3 IRF7402 Q2 2N2222 R2 10K Q1 2N2222 C10 100pF C4 0.01uF VOUT (7.5V / 0.5A) C9 2x 47uF C5 0.1uF R4 25K SS/SD Comp Vc U1 HDrv IRU3037 R3 20K Fb Vcc LDrv Gnd C8 1uF R5 R6 1K, 1% 5K, 1% Figure 19 - Typical application of IRU3037 as a boost converter. 16 www.irf.com Gnd IRU3037/IRU3037A & (PbF) DEMO-BOARD APPLICATION 5V or 12V to 3.3V @ 10A L1 VIN 5V or 12V 1uH C2A 47uF 16V D4 LL4148 C1 33uF 16V D1 LL4148 C2B 47uF 16V D2 Gnd LL4148 C3 1uF Vcc C19 1uF C6 0.1uF Vc C8 1uF Q1 IRF7457 HDrv L2 SS/SD C5 0.1uF VOUT 3.3V @ 10A 3.3uH U1 IRU3037 Q2 LDrv IRF7460 C7 470pF R4 4.7Ω C9B 150uF 6.3V C9C 150uF 6.3V C13 1uF Comp C4 2200pF Gnd R6 Gnd Fb 1.65K R5 1K R3 20K Figure 20 - Demo-board application of IRU3037. Application Parts List Ref Desig Q1 Q2 U1 D1, D2, D4 L1 L2 C1 C2A, C2B C9B, C9C C5, C6 C3 C4 C7 C8, C13, C19 R3 R4 R5 R6 Description MOSFET MOSFET Controller Diode Inductor Inductor Capacitor, Tantalum Capacitor, Poscap Capacitor, Poscap Capacitor, Ceramic Capacitor, Ceramic Capacitor, Ceramic Capacitor, Ceramic Capacitor, Ceramic Resistor Resistor Resistor Resistor Value Qty Part# 20V, 7mΩ, 15A 1 IRF7457 20V, 10mΩ, 12A 1 IRF7460 Synchronous PWM 1 IRU3037 Fast Switching 3 LL4148 1µH, 10A 1 D03316P-102HC 3.3µH, 12A 1 D05022P-332HC 33µF, 16V 1 ECS-T1CD336R 47µF, 16V, 70mΩ 2 16TPB47M 150µF, 6.3V, 40mΩ 2 6TPC150M 0.1µF, Y5V, 25V 2 ECJ-2VF1E104Z 1µF, X7R, 25V 1 ECJ-3YB1E105K 2200pF, X7R, 50V 1 ECJ-2VB1H222K 470pF, X7R 1 ECJ-2VB2D471K 1µF, Y5V, 16V 3 ECJ-2VF1C105Z 20K, 5% 1 4.7Ω, 5% 1 1K, 1% 1 1.65K, 1% 1 www.irf.com Manuf IR IR IR Coilcraft Coilcraft Panasonic Sanyo Sanyo Panasonic Panasonic Panasonic Panasonic Panasonic 17 IRU3037/IRU3037A & (PbF) DEMO-BOARD WAVEFORMS IRU3037 V IN VIN=5.0V, VOUT=3.3V Efficiency (%) 100 90 VOUT 80 70 0 1 2 3 4 5 6 7 8 9 10 11 Output Current (A) Figure 21 - Efficiency for IRU3037 Evaluation Board. Figure 22 - Start-up time @ IOUT=5A. IRU3037 Vss IRU3037 VOUT IOUT = 5V Figure 23 - Shutdown the output by pulling down the soft-start. Figure 24 - 3.3V output voltage ripple @ IOUT=5A. IRU3037 IRU3037 2A 4A 0A 0A Figure 25 - Transient response @ IOUT = 0 to 2A. 18 Figure 26 - Transient response @ IOUT = 0 to 4A. www.irf.com IRU3037/IRU3037A & (PbF) (F) TSSOP Package 8-Pin A L Q R1 B 1.0 DIA C R E N M P O D F DETAIL A PIN NUMBER 1 DETAIL A G J H K SYMBOL DESIG A B C D E F G H J K L M N O P Q R R1 8-PIN MIN MAX NOM 0.65 BSC 4.30 4.40 6.40 BSC --1.00 1.00 3.00 --0.90 --12) REF 12) REF --1.00 REF 0.60 0.20 ----- 0.19 2.90 --0.85 0.05 0) 0.50 0.09 0.09 4.50 0.30 3.10 1.10 0.95 0.15 8) 0.75 ----- NOTE: ALL MEASUREMENTS ARE IN MILLIMETERS. www.irf.com 19 IRU3037/IRU3037A & (PbF) (S) SOIC Package 8-Pin Surface Mount, Narrow Body H A B C E DETAIL-A PIN NO. 1 L D DETAIL-A 0.38± 0.015 x 45) K T F I J G 8-PIN SYMBOL A B C D E F G H I J K L T MAX MIN 4.98 4.80 1.27 BSC 0.53 REF 0.46 0.36 3.99 3.81 1.72 1.52 0.25 0.10 7) BSC 0.19 5.80 0) 0.41 1.37 0.25 6.20 8) 1.27 1.57 NOTE: ALL MEASUREMENTS ARE IN MILLIMETERS. 20 www.irf.com IRU3037/IRU3037A & (PbF) PACKAGE SHIPMENT METHOD PKG DESIG F S 1 PACKAGE DESCRIPTION TSSOP Plastic SOIC, Narrow Body 1 PIN COUNT 8 8 1 PARTS PER TUBE 100 95 1 PARTS PER REEL 2500 2500 1 T&R Orientation Fig A Fig B 1 Feed Direction Figure B Feed Direction Figure A LEADFREE PART MARKING INFORMATION Part number Date code IRxxxxxx YWW? ?XXXX Pin 1 Identifier ? P IR logo MARKING CODE Lead Free Released Non-Lead Free Released Lot Code (Prod mode - 4 digit SPN code) Assembly site code IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, CA 90245, USA Tel: (310) 252-7105 TAC Fax: (310) 252-7903 Visit us at www.irf.com for sales contact information Data and specifications subject to change without notice. 10/24/2005 www.irf.com 21