Previous Datasheet Index Next Data Sheet Bulletin I25164/B ST180C..C SERIES PHASE CONTROL THYRISTORS Hockey Puk Version Features 350A Center amplifying gate Metal case with ceramic insulator International standard case TO-200AB (A-PUK) Typical Applications DC motor controls Controlled DC power supplies AC controllers case style TO-200AB (A-PUK) Major Ratings and Characteristics Parameters ST180C..C Units 350 A 55 °C 660 A 25 °C @ 50Hz 5000 A @ 60Hz 5230 A @ 50Hz 125 KA2s @ 60Hz 114 KA2s 400 to 2000 V 100 µs - 40 to 125 °C IT(AV) @ Ths IT(RMS) @ Ths ITSM I 2t V DRM /V RRM tq TJ typical To Order PreviousSeries Datasheet ST180C..C Index Next Data Sheet ELECTRICAL SPECIFICATIONS Voltage Ratings Voltage V DRM /V RRM , max. repetitive VRSM , maximum non- I DRM /I RRM max. Code peak and off-state voltage repetitive peak voltage @ TJ = TJ max V V mA 04 400 500 08 800 900 12 1200 1300 16 1600 1700 18 1800 1900 20 2000 2100 Type number ST180C..C 30 12 On-state Conduction Parameter I T(AV) Max. average on-state current @ Heatsink temperature ST180C..C Units Conditions 350 (140) A 180° conduction, half sine wave 55 (85) °C double side (single side) cooled I T(RMS) Max. RMS on-state current 660 @ 25°C heatsink temperature double side cooled I TSM Max. peak, one-cycle 5000 t = 10ms No voltage non-repetitive surge current 5230 t = 8.3ms reapplied 4200 t = 10ms 100% VRRM 4400 t = 8.3ms reapplied Sinusoidal half wave, 125 t = 10ms No voltage Initial TJ = TJ max. t = 8.3ms reapplied t = 10ms 100% VRRM t = 8.3ms reapplied I 2t Maximum I2t for fusing A 114 KA2s 88 81 2 I √t 2 Maximum I √t for fusing V T(TO) 1 Low level value of threshold voltage V T(TO)2 High level value of threshold 2 KA √s 1250 (16.7% x π x IT(AV) < I < π x IT(AV)), TJ = TJ max. 1.08 V 1.14 (I > π x IT(AV)),TJ = TJ max. 1.18 (16.7% x π x IT(AV) < I < π x IT(AV)), TJ = TJ max. voltage r t1 Low level value of on-state slope resistance r t2 High level value of on-state slope resistance t = 0.1 to 10ms, no voltage reapplied 2222222222222 mΩ (I > π x IT(AV)),TJ = TJ max. 1.14 V TM Max. on-state voltage 1.96 IH Maximum holding current 600 IL Max. (typical) latching current 1000 (300) V Ipk= 750A, TJ = TJ max, tp = 10ms sine pulse mA TJ = TJ max, anode supply 12V resistive load To Order PreviousSeries Datasheet ST180C..C Index Next Data Sheet Fig. 3 - Current Ratings Characteristics Fig. 4 - Current Ratings Characteristics Fig. 5- On-state Power Loss Characteristics Fig. 6- On-state Power Loss Characteristics Fig. 7 - Maximum Non-Repetitive Surge Current To Order Fig. 8 - Maximum Non-Repetitive Surge Current Si l d D bl Sid C l d Previous Datasheet Index NextST180C..C Data SheetSeries Fig. 9 - On-state Voltage Drop Characteristics Fig. 10 - Thermal Impedance Z thJ-hs Characteristics Fig. 11 - Gate Characteristics To Order Previous Datasheet Index Next Data Sheet ST180C..C Series Switching Parameter di/dt ST180C..C Max. non-repetitive rate of rise 1000 of turned-on current td Typical delay time Units Conditions A/µs 1.0 µs tq Typical turn-off time 100 Gate drive 20V, 20Ω, tr ≤ 1µs TJ = TJ max, anode voltage ≤ 80% VDRM Gate current 1A, di g /dt = 1A/µs Vd = 0.67% VDRM, TJ = 25°C ITM = 300A, TJ = TJ max, di/dt = 20A/µs, VR = 50V dv/dt = 20V/µs, Gate 0V 100Ω, t p = 500µs Blocking Parameter ST180C..C Units Conditions dv/dt Maximum critical rate of rise of off-state voltage 500 V/µs TJ = TJ max linear to 80% rated VDRM IDRM IRRM Max. peak reverse and off-state leakage current 30 mA TJ = TJ max, rated V DRM/V RRM applied 23 Triggering Parameter PGM ST180C..C Maximum peak gate power 2.0 IGM Max. peak positive gate current 3.0 +VGM Maximum peak positive Maximum peak negative A TJ = TJ max, t p ≤ 5ms V TJ = TJ max, tp ≤ 5ms 5.0 gate voltage TYP. MAX. 180 - 90 150 40 - TJ = 125°C 2.9 - TJ = - 40°C 1.8 3.0 1.2 - TJ = - 40°C DC gate current required to trigger VGT TJ = TJ max, t p ≤ 5ms TJ = TJ max, f = 50Hz, d% = 50 20 gate voltage IGT W 10 PG(AV) Maximum average gate power -VGM Units Conditions DC gate voltage required to trigger mA V TJ = 25°C Max. required gate trigger/ current/ voltage are the lowest value which will trigger all units 12V anode-to-cathode applied TJ = 25°C TJ = 125°C IGD DC gate current not to trigger 10 mA VGD DC gate voltage not to trigger 0.25 V TJ = TJ max To Order Max. gate current/voltage not to trigger is the max. value which will not trigger any unit with rated VDRM anode-to-cathode applied PreviousSeries Datasheet ST180C..C Index Next Data Sheet Thermal and Mechanical Specification Parameter ST180C..C TJ Max. operating temperature range -40 to 125 Tstg Max. storage temperature range -40 to 150 RthJ-hs Max. thermal resistance, DC operation single side cooled K/W 0.08 RthC-hs Max. thermal resistance, wt °C 0.17 junction to heatsink F Units Conditions 0.033 K/W case to heatsink 0.017 Mounting force, ± 10% 4900 N (500) (Kg) 50 g Approximate weight Case style DC operation double side cooled DC operation single side cooled DC operation double side cooled TO - 200AB (A-PUK) See Outline Table ∆RthJ-hs Conduction 12 (The following table shows the increment of thermal resistence RthJ-hs when devices operate at different conduction angles than DC) Conduction angle Sinusoidal conduction Rectangular conduction Single Side Double Side Units Conditions Single Side Double Side 180° 0.015 0.015 0.011 0.011 120° 0.018 0.019 0.019 0.019 90° 0.024 0.024 0.026 0.026 60° 0.035 0.035 0.036 0.037 30° 0.060 0.060 0.060 0.061 TJ = TJ max. K/W Ordering Information Table Device Code ST 18 0 C 20 C 1 1 2 3 4 5 6 7 8 1 - Thyristor 2 - Essential part number 3 - 0 = Converter grade 4 - C = Ceramic Puk 5 - Voltage code: Code x 100 = VRRM (See Voltage Rating Table) 6 - C = Puk Case TO-200AB (A-PUK) 7 - 0 = Eyelet terminals (Gate and Auxiliary Cathode Unsoldered Leads) 2222222222222 1 = Fast-on terminals (Gate and Auxiliary Cathode Unsoldered Leads) 2 = Eyelet terminals (Gate and Auxiliary Cathode Soldered Leads) 3 = Fast-on terminals (Gate and Auxiliary Cathode Soldered Leads) 8 - Critical dv/dt: None = 500V/µsec (Standard value) L = 1000V/µsec (Special selection) To Order Previous Datasheet Index Next Data Sheet ST180C..C Series Outline Table ANODE TO GATE CREEPAGE DISTANCE: 7.62 (0.30) MIN. STRIKE DISTANCE: 7.12 (0.28) MIN. 19 (0.75) 0.3 (0.01) MIN. DIA. MAX. 13.7 / 14.4 (0.54 / 0.57) 0.3 (0.01) MIN. 19 (0.75) GATE TERM. FOR 1.47 (0.06) DIA. PIN RECEPTACLE DIA. MAX. 38 (1.50) DIA MAX. Case Style TO-200AB (A-PUK) All dimensions in millimeters (inches) 2 HOLES 3.56 (0.14) x 1.83 (0.07) MIN. DEEP 6.5 (0.26) 4.75 (0.19) 23 25°± 5° 42 (1.65) MAX. 28 (1.10) Fig. 1 - Current Ratings Characteristics Fig. 2 - Current Ratings Characteristics To Order