Previous Datasheet Index Next Data Sheet Bulletin I25194/A ST1230C..K SERIES PHASE CONTROL THYRISTORS Hockey Puk Version Features 1745A Center amplifying gate Metal case with ceramic insulator International standard case A-24 (K-PUK) High profile hockey-puk Typical Applications DC motor controls Controlled DC power supplies AC controllers case style A-24 (K-PUK) Major Ratings and Characteristics Parameters ST1230C..K Units 1745 A 55 °C 3200 A 25 °C @ 50Hz 33500 A @ 60Hz 35100 A @ 50Hz 5615 KA2s @ 60Hz 5126 KA2s 800 to 1600 V 200 µs - 40 to 125 °C IT(AV) @ Ths IT(RMS) @ Ths ITSM I 2t V DRM /V RRM tq TJ typical ToD-391 Order Previous Datasheet Index Next Data Sheet ST1230C..K Series ELECTRICAL SPECIFICATIONS Voltage Ratings Voltage V DRM /V RRM , max. repetitive VRSM , maximum non- I DRM /I RRM max. Code peak and off-state voltage repetitive peak voltage @ TJ = TJ max V V mA 08 800 900 12 1200 1300 14 1400 1500 16 1600 1700 Type number ST1230C..K 100 On-state Conduction Parameter I T(AV) Max. average on-state current @ Heatsink temperature 12 ST1230C..K Units Conditions 1745 (710) A 180° conduction, half sine wave 55 (85) °C double side (single side) cooled I T(RMS) Max. RMS on-state current 3200 DC @ 25°C heatsink temperature double side cooled I TSM Max. peak, one-cycle 33500 t = 10ms No voltage non-repetitive surge current 35100 I2 t Maximum I2t for fusing t = 8.3ms reapplied 28200 t = 10ms 100% VRRM 29500 t = 8.3ms reapplied Sinusoidal half wave, 5615 t = 10ms No voltage Initial TJ = TJ max. t = 8.3ms reapplied 5126 3971 A KA2s 3625 I2 √ t Maximum I2√t for fusing V T(TO) 1 Low level value of threshold voltage V T(TO) 2 High level value of threshold 56150 KA2√s t = 10ms 100% VRRM t = 8.3ms reapplied t = 0.1 to 10ms, no voltage reapplied (16.7% x π x IT(AV) < I < π x IT(AV)), TJ = TJ max. 0.93 V 1.02 (I > π x IT(AV)),TJ = TJ max. 0.17 (16.7% x π x IT(AV) < I < π x IT(AV)), TJ = TJ max. voltage 2222222222222 rt1 Low level value of on-state slope resistance rt2 High level value of on-state slope resistance mΩ (I > π x IT(AV)),TJ = TJ max. 0.16 V TM Max. on-state voltage 1.62 IH Maximum holding current 600 IL Typical latching current 1000 V mA D-392 To Order Ipk= 4000A, TJ = TJ max, tp = 10ms sine pulse T J = 25°C, anode supply 12V resistive load Previous Datasheet Index Next Data Sheet ST1230C..K Series Switching Parameter di/dt ST1230C..K Max. non-repetitive rate of rise 1000 of turned-on current t d Typical delay time 1.9 Typical turn-off time 200 Units Conditions A/µs µs t q Gate drive 20V, 20Ω , tr ≤ 1µs TJ = TJ max, anode voltage ≤ 80% VDRM Gate current 1A, di g/dt = 1A/µs V = 0.67% VDRM, TJ = 25°C d ITM = 550A, TJ = TJ max, di/dt = 40A/µs, VR = 50V dv/dt = 20V/µs, Gate 0V 100Ω, t = 500µs p Blocking Parameter ST1230C..K Units Conditions dv/dt Maximum critical rate of rise of off-state voltage 500 V/µs TJ = TJ max. linear to 80% rated VDRM IRRM IDRM Max. peak reverse and off-state leakage current 100 mA TJ = TJ max, rated V DRM/V RRM applied 23 Triggering Parameter PGM ST1230C..K Maximum peak gate power 16 PG(AV) Maximum average gate power IGM Max. peak positive gate current +VGM Maximum peak positive W 3 3.0 Maximum peak negative TYP. DC gate voltage required to trigger IGD VGD TJ = TJ max, t p ≤ 5ms V TJ = TJ max, t ≤ 5ms p MAX. 200 - 100 200 50 - TJ = - 40°C DC gate current required to trigger VGT A 5.0 gate voltage IGT DC gate current not to trigger DC gate voltage not to trigger TJ = TJ max, t p ≤ 5ms TJ = TJ max, f = 50Hz, d% = 50 20 gate voltage -VGM Units Conditions 1.4 - 1.1 3.0 0.9 10 mA TJ = 25°C TJ = 125°C TJ = - 40°C V TJ = 25°C TJ = 125°C mA 0.25 Max. required gate trigger/ current/ voltage are the lowest value which will trigger all units 12V anode-to-cathode applied V D-393 3333 To Order TJ = TJ max Max. gate current/voltage not to trigger is the max. value which will not trigger any unit with rated VDRM anode-to-cathode applied Previous Datasheet Index Next Data Sheet ST1230C..K Series Thermal and Mechanical Specification Parameter ST1230C..K TJ Max. operating temperature range -40 to 125 T Max. storage temperature range -40 to 150 stg RthJ-hs Max. thermal resistance, 0.006 case to heatsink K/W 0.003 Mounting force, ± 10% wt DC operation single side cooled K/W 0.021 RthC-hs Max. thermal resistance, 24500 N (Kg) 425 g Case style DC operation double side cooled DC operation single side cooled DC operation double side cooled (2500) Approximate weight Conditions °C 0.042 junction to heatsink F Units A-24 (K-PUK) See Outline Table ∆RthJ-hs Conduction 12 (The following table shows the increment of thermal resistence RthJ-hs when devices operate at different conduction angles than DC) Sinusoidal conduction Rectangular conduction Single Side Double Side Single Side Double Side Conduction angle Units 180° 0.003 0.003 0.002 0.002 120° 0.004 0.004 0.004 0.004 90° 0.005 0.005 0.005 0.005 60° 0.007 0.007 0.007 0.007 30° 0.012 0.012 0.012 0.012 Conditions TJ = TJ max. K/W Ordering Information Table Device Code ST 123 1 2 0 C 16 K 1 3 4 5 6 7 8 1 - Thyristor 2 - Essential part number 3 - 0 = Converter grade 4 - C = Ceramic Puk 5 - Voltage code: Code x 100 = VRRM (See Voltage Rating Table) 6 - K = Puk Case A-24 (K-PUK) 7 - 0 = Eyelet terminals (Gate and Auxiliary Cathode Unsoldered Leads) 2222222222222 1 = Fast-on terminals (Gate and Auxiliary Cathode Unsoldered Leads) 2 = Eyelet terminals (Gate and Auxiliary Cathode Soldered Leads) 3 = Fast-on terminals (Gate and Auxiliary Cathode Soldered Leads) 8 - Critical dv/dt: None = 500V/µsec (Standard selection) L = 1000V/µsec (Special selection) D-394 To Order Previous Datasheet Index Next Data Sheet ST1230C..K Series Outline Table 1 (0.04) MIN. TWO PLACES 47.5 (1.87) DIA. MAX. 2 7.5 (1.0 8) M A X . TWO PLACES PIN RECEPTACLE AMP. 60598-1 Case Style A-24 (K-PUK) All dimensions in millimeters (inches) 67 (2.6) DIA. MAX. 20° ± 5° 7 4.5 (2.9 ) D IA . M A X . 4.75 (0.2) NOM. 23 44 (1.73) 2 HOLES DIA. 3.5 (0.14) x 2.1 (0.1) DEEP 130 ST1230C..K Series (Single Side Cooled) R thJ-hs (DC) = 0.042 K/W 120 110 100 90 Conduction Angle 80 30° 60° 70 120° 60 180° 50 40 90° 0 200 400 600 800 1000 1200 1400 Average On-state Current (A) Fig. 1 - Current Ratings Characteristics Maximum Allowable Heatsink Temperature (°C) Maximum Allowable Heatsink Temperature (°C) CREPAGE DESTANCE 28.88 (1.137) MIN. STRIKE DISTANCE 17.99 (0.708) MIN. 130 ST1230C..K Series (Single Side Cooled) R thJ-hs(DC) = 0.042 K/W 120 110 100 90 Conduction Period 80 70 60 50 30° 40 60° 90° 30 20 0 400 800 120° 180° 1200 DC 1600 2000 Average On-state Current (A) Fig. 2 - Current Ratings Characteristics D-395 3333 To Order