INTEGRATED CIRCUITS DATA SHEET TDA1596T IF amplifier/demodulator for FM radio receivers Product specification File under Integrated Circuits, IC01 April 1991 Philips Semiconductors Product specification IF amplifier/demodulator for FM radio receivers TDA1596T GENERAL DESCRIPTION The TDA1596T provides IF amplification, symmetrical quadrature demodulation and level detection for quality home and car FM radio receivers and is suitable for both mono and stereo reception. It may also be applied to common front-ends, stereo decoders and AM receiver circuits. Features • Simulates behaviour of a ratio detector (internal field strength and detuning-dependent voltage for dynamic AF signal muting) • Mono/stereo blend and field strength indication control voltage • Three-state mode switch for FM, mute-on / FM, mute-off / FM-off • Internal compensation of AF signal total harmonic distortion (THD) • Two open collector stop pulse outputs for microcomputer tuning control (can be one stop pulse output by wired-ANDing) • Internal reference voltage source • Built-in hum and ripple rejection circuits. QUICK REFERENCE DATA SYMBOL PARAMETER VP Supply voltage (pin 1) IP Supply current (pin 1) V4(rms) AF output voltage (RMS value) S/N CONDITIONS MIN. TYP. MAX. UNIT 7.5 8.5 12.0 V VP = 8.5 V; I2 = I7 = 0 mA − 20 26 mA V20(rms) = 10 mV 180 200 220 mV Signal-to-noise ratio V20(rms) = 10 mV; fm = 400 Hz; ∆f = 75 kHz − 82 − dB THD Total harmonic distortion − V20(rms) = 10 mV; fm = 1 kHz; I7 = 0 mA; ∆f = 75 kHz; FM mute on; without de-emphasis; without detuning 0.1 0.3 % Tamb Operating ambient temperature range − + 85 °C −40 SEE ALSO DATA SHEET FOR TDA1596 PACKAGE OUTLINE 20-lead mini-pack; plastic (SO20; SOT163A); SOT163-1; 1996 August 12. April 1991 2 IF amplifier/demodulator for FM radio receivers April 1991 3 Fig.1 Block diagram and application circuit. (1) Connecting pin 13 to ground is only allowed for measuring the current at pin 16. It is not for use in application. (2) In the FM, mute-on condition the unweighted level detector output is available from pin 3. In the FM, mute-off condition the variable resistor at pin 3 can be adjusted for minimum 2nd harmonic distortion at pin 4. Philips Semiconductors Product specification TDA1596T Philips Semiconductors Product specification IF amplifier/demodulator for FM radio receivers TDA1596T PINNING 1 VP supply voltage 2 LVA level voltage adjustment 3 ULV unweighted level output/K2 adjustment 4 AF0 AF output 5 Vref reference voltage output 6 WLV weighted level voltage output 7 MSW mode switch 8 DDV detune detector voltage 9 n.c. not connected 10 DMI1 demodulator input 1 11 DMI2 demodulator input 2 12 n.c. not connected 13 TSW tau switch 14 ST1 stop pulse output 1 15 ST0 stop pulse output 0 16 MTV mute voltage 17 GND ground 18 LFD1 IF limiter feedback 1 19 LFD2 IF limiter feedback 2 20 IFI IF input April 1991 Fig.2 Pinning diagram. 4 Philips Semiconductors Product specification IF amplifier/demodulator for FM radio receivers TDA1596T FUNCTIONAL DESCRIPTION Limiter-amplifier This has five stages of IF amplification using balanced differential limiter-amplifiers with emitter--follower coupling. Decoupling of the stages from the voltage supply lines and an internal high-ohmic DC feed-back loop give a very stable IF performance. The amplifier gain is virtually independent from temperature changes. FM demodulator The demodulator is fully balanced and comprises two cross-coupled differential amplifiers. Quadrature detection of the FM signal is performed by feeding one differential amplifier directly from the limiter--amplifier output, and the other via an external 90° phase-shifting network. The demodulator has good stability and its zero cross-over shift is small. The bandwidth of the demodulator output is restricted to approximately 1 MHz by an internal low-pass filter. THD compensation This circuit compensates non-linearities introduced by demodulation. For this to operate correctly the demodulator circuit between pins 10 and 11 must have a loaded Q-factor of 19. Consequently there is no need for the demodulator tuned circuit to be adjusted for minimum THD, instead the adjustment criterium is for a symmetrical stop pulse. Mute attenuator and AF output The control voltage for the mute attenuator at pin 16 is generated from the values of the level detector and the detuning detector outputs. The mute attenuator has a fast attack and a slow decay which is determined by the capacitor at pin 16. The AF signal is passed via the mute attenuator to the output at pin 4. A weighted control voltage, available from pin 6, is obtained from the mute attenuator control voltage via a buffer-amplifier which introduces an additional voltage shift and gain. Level detector The level detector generates a voltage output which is proportional to the field strength of the input signal. The unweighted level detector output is available when the mode switch is operating in the FM, mute-on condition. Tuning-stop outputs The open collector outputs STOP-0 and STOP-1 (from pins 15 and 14 respectively) are voltages derived from the detuning level and the field strength of the input signal. If only one tuning-stop output is required, pins 14 and 15 may be tied together. April 1991 5 Philips Semiconductors Product specification IF amplifier/demodulator for FM radio receivers TDA1596T RATINGS Limiting values in accordance with the Absolute Maximum System (IEC 134) SYMBOL PARAMETER MIN. MAX. UNIT VP = V1-17 Supply voltage (pin 1) −0.3 +16 V V5-17 Reference voltage range (pin 5) −0.3 + 10 V V2-17 Level adjustment range (pin 2) −0.3 + 10 V V7-17 Mode switch voltage range (pin 7) −0.3 VP V V13-17 Control input voltage range (pin 13) − +6 V −0.3 VP V THD compensation/unweighted field V3-17 strength voltage range (pin 3) Tuning-stop output voltage range V15-17 STOP-0 (pin 15) −0.3 VP V V14-17 STOP-1 (pin 14) −0.3 VP V Tuning-stop output current I15 STOP-0 (pin 15) − 2 mA I14 STOP-1 (pin 14) − 2 mA Tstg Storage temperature range −55 + 150 °C Tamb Operating ambient temperature range −40 + 85 °C Electrostatic handling(1) Ves all pins except pins 5 and 6 −2000 + 2000 V Ves pin 5 −2000 + 900 V Ves pin 6 −2000 + 1600 V Note 1. Equivalent to discharging a 100 pF capacitor through a 1.5 kΩ series resistor. THERMAL RESISTANCE From junction to ambient (in free air) April 1991 Rth j-a (max.) 6 = 95 K/W Philips Semiconductors Product specification IF amplifier/demodulator for FM radio receivers TDA1596T CHARACTERISTICS f = 10.7 MHz; VP = V1-17 = 8.5 V; VI = V20 (rms) = 1 mV; Tamb = 25 °C; measured in the circuit of Fig.3; tuned circuit at pins 10, 11 aligned for symmetrical stop pulses; all voltages are referred to ground (pin 17), unless otherwise specified SYMBOL PARAMETER MIN. TYP. MAX. UNIT Supplies VP = V1 Supply voltage 7.5 8.5 12.0 V I1 Supply current at I2 = I7 = 0 mA − 20 26 mA 25 40 55 kΩ − 6 − pF FM demodulator R10-11 Input impedance C10-11 V4 DC output voltage (no-signal condition) at V10, 11(p-p) ≤ 100 µV; V20(rms) ≤ 5 µV 2.75 3.10 3.45 V R4-17 Output impedance − 400 − Ω Mute attenuator control voltage Control voltage (pin 16) V16 at V20(rms) ≤ 5 µV − 2.0 − V V16 at V20(rms) = 1 mV − 3.45 − V R10-17 Output impedance (pin 16) − − 2.0 MΩ V2 Level shift input (pin 2) internal bias voltage at I2 = 0 mA − 1.4 − V 15 − − kΩ R2-17 input impedance Internal muting (Fig.6) Internal attenuation of signals ± 22.5 kHz ≤ detuning ≤ ±80 kHz; A = 20log[∆V4(FM mute-off)/∆V4(FM)] A at V16 ≥ 1 V5 − 0 − dB A at V16 = 0.77 V5 1.5 3.0 4.5 dB A at V16 = 0.55 V5 − 20 − dB April 1991 7 Philips Semiconductors Product specification IF amplifier/demodulator for FM radio receivers SYMBOL TDA1596T PARAMETER MIN. TYP. MAX. UNIT Attack and decay (pin 16) Pin 13 connected to ground * +I16 charge current − 8 − µA −I16 discharge current − 120 − µA Pin 13 connected to Vref +I16 charge current − 100 − µA −I16 discharge current − 120 − µA Level detector ∆V 6 -------------V 6 ∆T Dependence of output voltage on temperature − 3.3 − mV/VK R6 Output impedance − − 500 Ω Dependence of output voltage (pin 6) on input voltage (pin 20) (Fig.7): V6 V20(rms) ≤ 5 µV; I2 = I7 = 0 mA 0.1 0.7 1.3 V V6 V20(rms) = 1 mV; I2 = I7 = 0 mA 3.0 3.6 4.2 V 1.4 1.7 2.0 V/20 dB ∆V 6 ---------------------------20 ∆log V 20 Slope of output voltage (pin 6) for input voltage range V20(rms) ≥50 µV to V20(rms) ≤50 mV Dependence of output voltage (pin 6) on detuning (Fig.8) at input voltage V20(rms) = 10 mV: ∆V6 detuning = ≤ ±45 kHz − − 0.2 V ±∆f detuning for V6 = 1.8 V 90 − 160 kHz V6 detuning = ±200 kHz 0.5 0.7 0.9 V − 35 − mV/kHz 1.6 2.0 − V |∆V6/∆f| Slope of output voltage with detuning = 125 ± 20 kHz at V20(rms) = 10 mV Level shift control (pin 2) (Fig.9) ±∆V6 adjustment range −(∆V6/∆V2) adjustment gain − 1.7 − V V6 output voltage at V2 = V5; V20(rms) ≤ 5 µV − − 0.3 V V20(rms) ≤ 5 µV − 2.2 − V Internal resistance 12 25 50 kΩ Low-pass filter at pin 8 Output voltage at I7 = 0 mA; V8 R8(int) April 1991 8 Philips Semiconductors Product specification IF amplifier/demodulator for FM radio receivers SYMBOL TDA1596T PARAMETER MIN. TYP. MAX. UNIT Tuning-stop detector (Figs 10 and 11) Stop-0: detuning at V20(rms) = 10 mV +∆f for V15 ≥ 3.5 V − − 10 kHz +∆f for V15 ≤ 0.3 V 18 − − kHz Stop-1: detuning at V20(rms) = 10 mV −∆f for V14 ≥ 3.5 V − − 10 kHz −∆f for V14 ≤ 0.3 V 18 − − kHz 250 − − µV − − 50 µV − − 0.3 V − − 1.4 V − 2.8 − V − − 2.5 µA − 2 − V − − 100 Ω Dependence of STOP-0, STOP-1 on input voltage (pin 20) input voltage (RMS value) for V20(rms) V14 = V15 ≥ 3.5 V V20(rms) V14 = V15 ≤ 0.3 V input voltage (RMS value) for Output voltage when V14, 15 I14 = I15 = 1 mA Mode switch and pin 3 (Fig.12) FM-off position Control voltage for 60 dB V7 muting depth FM, mute-on position (pin 3 = output) Internal bias voltage at V7 |I7| R7-17 ≥ 10 MΩ Input current Output voltage with V3 R3-17 = 10 kΩ; C3-17 ≥ 1 nF* Output impedance for V20 = ≤ 5 µV; R3-17 I3 = 500µA FM, mute-off position (pin 3 = input) V7 Control voltage 0.9 V5 − − V I7 Input current at V7 = V5 − − 15 µA R3-17 Input resistance 1 − − MΩ Reference voltage source V5 Output voltage at I5 = −1 mA 3.3 3.7 4.1 V ∆V5/I5 Output impedance at I5 = −1 mA − 40 80 Ω TC Temperature coefficient − 3.3 − mV/K * Connecting pin 13 to ground is only allowed for measuring the current at pin 16. It is not for use in application. * Without input voltage. April 1991 9 Philips Semiconductors Product specification IF amplifier/demodulator for FM radio receivers TDA1596T OPERATING CHARACTERISTICS f = 10.7 MHz; VI = V20(rms) = 1 mV; deviation (∆f) = 22.5 kHz; modulation frequency (fm) = 400 Hz; de-emphasiss (pin 4) = 50 µs; test circuit as per Fig.3; tuned circuit (QL = 19) aligned for symmetrical stop pulses; Tamb = + 25 °C; unless otherwise specified SYMBOL PARAMETER MIN. TYP. MAX. UNIT V4(rms) AF output voltage (RMS value) at V20(rms) = 10 mV 180 200 220 mV V20(rms) Start of limiting (FM, mute-off); (RMS value) (Fig.13) 14 22 35 µV Dependence of signal-to-noise ratio (in noise frequency band 250 Hz to 15 kHz, unweighted) on input voltage V18(rms) for S/N = 26 dB − 15 − µV V18(rms) for S/N = 46 dB − 60 − µV − 82 − dB THD THD (FM, mute-on) at V20(rms) = 10 mV; ∆f = 75 kHz; fm = 1 kHz; without detuning; without de-emphasis; I7 = 0 mA − 0.1 0.3 % αD Dynamic mute attenuation (Fig.14) − 16 − dB − 0.8 − dB/kHz − − 0.6 % S/N at V20(rms) = 10 mV; ∆f = 75 kHz V 4 ( FM mute – off ) α D = 20 log --------------------------------------------------------V 4 ( FM , mute – on ) with fm = 100 kHz; ∆f = 75 kHz αD∆f Slope of attenuation curve THD (FM, mute-on) at V20(rms) = 10 mV; ∆f = 75 kHz; fm = 1 kHz; detuning ≤± 25 kHz without THD de-emphasis; I7 = 0 mA (Fig.15) THD (FM, mute-off and compensated via pin 3) at V20(rms) = 10 mV; ∆f = 75 kHz; fm = 1 kHz; THD V3 April 1991 − 0.07 0.25 % Voltage range at pin 3 for THD compensation 0 − V5 V AM suppression (FM, mute-off) with amplitude modulation at 30% input voltage range V20 = 300 µV to 100 mV (Fig.16) − 65 − dB V7 = V 5 Power supply ripple rejection = 20log [∆V1/∆V4] 33 36 − dB Mute attenuation (FM-off) = 20log [V4(FM-on/V4(FM-off)] 60 − − dB 10 Philips Semiconductors Product specification TDA1596T Fig.3 Test circuit. IF amplifier/demodulator for FM radio receivers April 1991 11 Philips Semiconductors Product specification IF amplifier/demodulator for FM radio receivers TDA1596T Fig.4 Printed-circuit board component side, showing component layout. For circuit diagram see Fig.3. Fig.5 Printed-circuit board showing track side. April 1991 12 Philips Semiconductors Product specification IF amplifier/demodulator for FM radio receivers TDA1596T Fig.6 Typical curve of internal attenuation showing the relationship between the mute attenuator control voltage (pin 16) and mute attenuation; I2 = I7 = 0 mA Fig.7 Weighted field strength output voltage (pin 6) as a function of input voltage (pin 20); R6-17 ≥ 10 kΩ; I2 = I7 = 0 mA. April 1991 13 Philips Semiconductors Product specification IF amplifier/demodulator for FM radio receivers TDA1596T Fig.8 Weighted field strength output voltage (pin 6) as a function of detuning; R6-17 ≥ 10 kΩ; I2 = I7 = 0 mA; V20 = 10 mV. Fig.9 Adjustment range of weighted field strength output voltage (pin 6) with level shift control (pin 2); R6-17 ≥ 10 kΩ; I7 = 0 mA. April 1991 14 Philips Semiconductors Product specification IF amplifier/demodulator for FM radio receivers TDA1596T (a) STOP-0. (b) STOP-1. Fig.10 STOP-0 and STOP-1 output voltages as a function of detuning, measured at V20 = 10 mV. April 1991 15 Philips Semiconductors Product specification IF amplifier/demodulator for FM radio receivers TDA1596T Fig.11 STOP-0 or STOP-1 output voltages as a function of input voltage at pin 20. Fig.12 Switch levels at pin 7. April 1991 16 Philips Semiconductors Product specification IF amplifier/demodulator for FM radio receivers TDA1596T (a) mode switch at FM, mute-on (b) mode switch at FM, mute-off Fig.13 Audio signal (∆f = 22.5 kHz; fm = 1 kHz) and noise as functions of input voltage at pin 20; measured with 50 µs de-emphasis. April 1991 17 Philips Semiconductors Product specification IF amplifier/demodulator for FM radio receivers TDA1596T Fig.14 Dynamic mute attenuation as a function of frequency deviation for modulation frequencies of 40, 60, 80 and 100 kHz. Fig.15 THD as a function of detuning, mode switch at FM, mute-on position; ∆f = 75 kHz; fm = 1 kHz; V20(rms) = 10 mV. April 1991 18 Philips Semiconductors Product specification IF amplifier/demodulator for FM radio receivers TDA1596T (a) mode switch at FM, mute-on (b) mode switch at FM, mute-off Fig.16 Typical curves showing AM suppression for an input signal having frequency modulation at ∆f = 22.5 kHz and fm = 1 kHz, and amplitude modulation of 30% at a frequency of 400 Hz; de-emphasis time = 50 µs and bandwidth = 250 Hz to 15 kHz. April 1991 19 Philips Semiconductors Product specification IF amplifier/demodulator for FM radio receivers TDA1596T PACKAGE OUTLINE SO20: plastic small outline package; 20 leads; body width 7.5 mm SOT163-1 D E A X c HE y v M A Z 11 20 Q A2 A (A 3) A1 pin 1 index θ Lp L 1 10 e bp detail X w M 0 5 10 mm scale DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT A max. A1 A2 A3 bp c D (1) E (1) e HE L Lp Q v w y mm 2.65 0.30 0.10 2.45 2.25 0.25 0.49 0.36 0.32 0.23 13.0 12.6 7.6 7.4 1.27 10.65 10.00 1.4 1.1 0.4 1.1 1.0 0.25 0.25 0.1 0.9 0.4 0.012 0.096 0.004 0.089 0.01 0.019 0.013 0.014 0.009 0.51 0.49 0.30 0.29 0.050 0.42 0.39 0.055 0.043 0.016 0.043 0.039 0.01 0.01 0.004 0.035 0.016 inches 0.10 Z (1) θ Note 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. REFERENCES OUTLINE VERSION IEC JEDEC SOT163-1 075E04 MS-013AC April 1991 EIAJ EUROPEAN PROJECTION ISSUE DATE 92-11-17 95-01-24 20 o 8 0o Philips Semiconductors Product specification IF amplifier/demodulator for FM radio receivers TDA1596T SOLDERING Wave soldering Introduction Wave soldering techniques can be used for all SO packages if the following conditions are observed: There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and surface mounted components are mixed on one printed-circuit board. However, wave soldering is not always suitable for surface mounted ICs, or for printed-circuits with high population densities. In these situations reflow soldering is often used. • A double-wave (a turbulent wave with high upward pressure followed by a smooth laminar wave) soldering technique should be used. • The longitudinal axis of the package footprint must be parallel to the solder flow. • The package footprint must incorporate solder thieves at the downstream end. This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our “IC Package Databook” (order code 9398 652 90011). During placement and before soldering, the package must be fixed with a droplet of adhesive. The adhesive can be applied by screen printing, pin transfer or syringe dispensing. The package can be soldered after the adhesive is cured. Reflow soldering Reflow soldering techniques are suitable for all SO packages. Maximum permissible solder temperature is 260 °C, and maximum duration of package immersion in solder is 10 seconds, if cooled to less than 150 °C within 6 seconds. Typical dwell time is 4 seconds at 250 °C. Reflow soldering requires solder paste (a suspension of fine solder particles, flux and binding agent) to be applied to the printed-circuit board by screen printing, stencilling or pressure-syringe dispensing before package placement. A mildly-activated flux will eliminate the need for removal of corrosive residues in most applications. Several techniques exist for reflowing; for example, thermal conduction by heated belt. Dwell times vary between 50 and 300 seconds depending on heating method. Typical reflow temperatures range from 215 to 250 °C. Repairing soldered joints Fix the component by first soldering two diagonallyopposite end leads. Use only a low voltage soldering iron (less than 24 V) applied to the flat part of the lead. Contact time must be limited to 10 seconds at up to 300 °C. When using a dedicated tool, all other leads can be soldered in one operation within 2 to 5 seconds between 270 and 320 °C. Preheating is necessary to dry the paste and evaporate the binding agent. Preheating duration: 45 minutes at 45 °C. April 1991 21 Philips Semiconductors Product specification IF amplifier/demodulator for FM radio receivers TDA1596T DEFINITIONS Data sheet status Objective specification This data sheet contains target or goal specifications for product development. Preliminary specification This data sheet contains preliminary data; supplementary data may be published later. Product specification This data sheet contains final product specifications. Limiting values Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. April 1991 22