PHILIPS SA900BE

INTEGRATED CIRCUITS
SA900
I/Q transmit modulator
Preliminary specification
IC17 Data Handbook
1997 Sept 16
Philips Semiconductors
Preliminary specification
I/Q transmit modulator
SA900
DO NOT DISTRIBUTE WITHOUT ECN DATED AFTER Sept 16, 1997
DESCRIPTION
PIN CONFIGURATION
The SA900 is a monolithic high performance, multi-function transmit
modulator for use in cellular radio applications, fabricated in QUBiC
BiCMOS technology. The SA900 features both analog (AMPS)
mode and complex, I/Q digital (NADC IS–136) mode quadrature
modulation functions, a PLL synthesizer with VCO, crystal oscillator,
programmable prescalers and Gilbert cell multiplier phase detector
with programmable charge pump output. The DUALTX output can
be used in DUAL mode cellular phone applications with the AMPS
and NADC modulation being applied to the I/Q baseband inputs.
The DUALTX output also provides 6-bit power control with 40dB of
gain control in 0.63dB steps. In addition, buffered crystal oscillator
programmable prescaler outputs are provided to support system
clock reference needs. Programming of the SA900 functions are
realized by a high speed 3-wire serial interface. The SA900 can be
programmed into a sleep mode (low current mode providing crystal
oscillator and Master Clock functions), a standby mode (providing
crystal oscillator, Master Clock, System Clock 1 and Transmit LO
buffer functions), and the AMPS mode and the DUAL mode
configurations.
GND
TXLO_2
TXLO_1
Vcc
PHSOUT
GND
Vcc
3
5
Vcc
GND
2
4
TANK_2
41 40 39 38 37
1
GND
TANK_1
Q
I
48 47 46 45 44 43 42
Q
I
Vcc
GND
LO_1
LO_2
Vcc
BE Package
6
7
8
9
IPEAK 10
GND 11
XTAL_1 12
FEATURES
36
Vcc
35
GND
34
DUALTX
33
GND
32
Vcc
31
AMPSTX
30
GND
29
Vcc
28
GND
27
Vcc
26
Vcc
25
GND
TXEN
STROBE
DATA
CLOCK
CLKSET
MCLK
GND
CLK2
GND
CLK1
XTAL_2
Vcc
13 14 15 16 17 18 19 20 21 22 23 24
• VCC = 4.0V
• Tx output frequency = 900MHz
• Direct modulation of RF
• DUAL mode, on-chip PA control
• I/Q modulator
• Single sideband quadrature LO generation with no external
SR00636
Figure 1. Pin Configuration
• Selective power-down
– Low power AMPS/TACS mode
– Low power dual mode NADC
adjustments required
• On-chip crystal oscillator with 3 buffered outputs
• AMPS/TACS compatible
• On-chip VCO
• 48-Pin TQFP package
APPLICATIONS
• North American Digital Cellular (TDMA IS-136)
ORDERING INFORMATION
DESCRIPTION
48-Pin Plastic Low Profile Quad Flat Package (LQFP)
1997 Sept 16
2
TEMPERATURE RANGE
ORDER CODE
DWG #
-40 to +85°C
SA900BE
SOT313-2
853-
Philips Semiconductors
Preliminary specification
I/Q transmit modulator
SA900
BLOCK DIAGRAM
LO_2
I
LO_1
TXLO_2
TXLO
LPF
TXLO_1
PHASE
I
QQ
VGA
LPF
PA
DUALTX
PA
AMPSTX
SHIFT
TANK_1
NETWORK
IMAGE
REJECT
MIXER
VCO
LPF
TANK_2
VCO
÷N
÷A8/1
PHSOUT
PHS
DET
VGA
CONTROL
AD
BIAS
BG
AD
÷B8/1
IPEAK
2
SE
N<0:1>
AD
SM1
SM2
Y
X
AD
6
XTAL_1
XTAL_2
XTAL
OSC
÷ 3/1
X
SM1
÷ 2/1
Y
SM2
÷4/5/1
CONTROL
LOGIC
CONV2
SM1
CLK1
SM2
CLK2
MCLK
CLKSET
DATA
CLOCK STROBE TXEN
SR00637
Figure 2. Block Diagram
1997 Sept 16
3
Philips Semiconductors
Preliminary specification
I/Q transmit modulator
SA900
PIN DESCRIPTIONS
Pin
Description
I
Non-inverting I Mod Signal
I
Inverting I Mod Signal
TXLO_1/2
DUALTX
Second LO Input (differential/single-ended input)
RF output (850MHz) digital (DUAL) mode, complex modulated output
Q
Non-inverting Q Mod Signal
Q
Inverting Q Mod Signal
CLK1
Buffered oscillator output (XO ÷3/÷1)
MCLK
Buffered oscillator output (XO ÷4/÷5/÷1)
CLK2
Buffered oscillator output (XO ÷2/÷1)
AMPSTX
RF output (850MHz) AMPS mode
VCC
+5VDC power supply
GND
Ground
Data
Serial data input
Clock
Serial clock input
Strobe
Data strobe input
TXEN
AMPS and Dual Mode transmit enable
CLKSET
Program control pin for MCLK prescaler
XTAL1
Crystal oscillator base input
XTAL2
Crystal oscillator emitter output
PHSOUT
Phase comparator charge pump output
TANK_1
VCO differential tank
TANK_2
VCO differential tank
LO_1/2
Buffered differential TXLO output
IPEAK
1997 Sept 16
Phase comparator current programming
4
Philips Semiconductors
Preliminary specification
I/Q transmit modulator
SA900
GND_LO
GND
GND
GND
GND
GND_CTRL
GND
GND
GND
GND
GND
GND
GND
1
4
11
16
18
25
28
30
33
35
37
39
45
GND
VCC_LO
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC_CTRL
48
5
8
14
27
29
32
36
38
44
26
VCC
2
50Ω
VCC
50Ω
3
VCC
6
VCC
7
VCC
VCC
12
0.1/6.4 mA
9
VCC
0.1/6.4 mA
13
SR00638
Figure 3. Pin Diagrams
1997 Sept 16
5
Philips Semiconductors
Preliminary specification
I/Q transmit modulator
SA900
VCC
VCC
500Ω
15
17
19
20
VCC
500Ω
21
22
23
24
VCC
VCC
600Ω
30Ω
31
34
VCC
40
42
680Ω
680Ω
VCC
41
43
VCC
20Ω
46
47
SR00639
Figure 4. Pin Diagrams (cont.)
1997 Sept 16
6
Philips Semiconductors
Preliminary specification
I/Q transmit modulator
SA900
ABSOLUTE MAXIMUM RATINGS
SYMBOL
PARAMETER
VCC
Supply voltage
VIN
Voltage applied to any other pin
PD
Power dissipation, TA = 25°C (still air)
RATING
UNITS
-0.3 to +6
V
-0.3 to (VCC + 0.3)
V
600
mW
TJMAX
Maximum operating junction temperature
150
°C
PMAX
Maximum power input/output
+10
dBm
TSTG
Storage temperature range
–65 to +150
°C
NOTE:
1. Maximum dissipation is determined by the operating ambient temperature and the thermal resistance, θJA.
48-pin LQFP:
θJA = 67°C/W
RECOMMENDED OPERATING CONDITIONS
SYMBOL
VCC
PARAMETER
RATING
UNITS
Supply voltage
3.9 to 5.1
V
TA
Operating ambient temperature range
-40 to +85
°C
TJ
Operating junction temperature
-40 to +105
°C
DC ELECTRICAL CHARACTERISTICS
VCC = +4.0V, TA = 25°C; unless otherwise stated.
SYMBOL
VCC
PARAMETER
TEST CONDITIONS
Power supply range
LIMITS
MIN
TYP
3.9
Sleep mode
MAX
5.1
UNITS
V
3.1
Standby mode
8.2
AMPS mode
27.5
ICC
Supply current
DUAL mode
64
I/I
In-phase differential baseband input
DC
0.5VCC
V
Quadraphase differential baseband input
DC
0.5VCC
V
Divide by 4/5/1
÷4
÷5
÷1
Q/Q
CLKSET
mA
VCC
0.5VCC
V
0
VIL
Clock, data, strobe, TXEN
Input low
–0.3
0.3VCC
V
VIH
Clock, data, strobe, TXEN
Input high
0.7VCC
VCC+0.3
V
1997 Sept 16
7
Philips Semiconductors
Preliminary specification
I/Q transmit modulator
SA900
AC ELECTRICAL CHARACTERISTICS
VCC = +4.0V, TA = 25°C; TANK_1 = 120MHz @ 0 dBm; XO_REF = 30MHz @ –5 dBm; TxLO2 = –13 dBm, unless otherwise stated.
SYMBOL
PARAMETER
TEST CONDITIONS
Input power
TXLO_1/2 Transmit LO input (AC couple) (50Ω)
TANK_1/2 VCO tank differential inputs
PHSOUT
IPEAK
XTAL 1
XTAL_1
CLK1
Phase detector charge pump output
PHSOUT programming
XO transistor base
XO divide 3/1, power down SM1=0, 50%
duty cycle
÷3, X=1, ÷1, X=0
CLK2
XO divide 2/1, power down SM2=0
÷2, Y=1, ÷1, Y=0
XO divide 4/5/1, 50% duty cycle
MCLK
÷4, CLKSET = VCC, ÷5, CLKSET = 0.5VCC,
÷1, CLKSET = 0V
Serial data clock input, 33% duty cycle
CLOCK
LIMITS
MIN
900
Frequency range
901
Output level
0.5
RSET = 24kΩ, AD=0
200
300
RSET = 24kΩ, AD=1
0.9
1.2
1.5
mA
XO frequency
101
30
451
MHz
External drive
1501
350
5001
mVP-P
Frequency range
3.331
30
451
MHz
Output level, 5kΩ || 7pF
0.7
1
1.4
VP-P
Frequency range
51
30
451
MHz
Output level, 5kΩ || 7pF
0.7
1
Frequency range
21
Output level, 5kΩ || 7pF
0.7
Logic LOW
0.7VCC
Frequency range
820
DUAL output, SE=1, AD=1, TXEN=1 (with
external matching Figure 9)
DUALTX
V
400
µA
1.4
VP-P
451
MHz
1.4
VP-P
MHz
1
V
V
860
MHz
+2
dBm
869 to 894MHz
-104
dBm
824 to 849MHz
-47
dBc
2 to 824MHz
-41
dBc
849 to 869MHz
-41
dBc
894MHz to 8.49GHz
-41
dBc
-21
dBc
@30kHz
-95
dBc/Hz
@60kHz
-101
dBc/Hz
869 to 894MHz
-136
dBm/Hz
Frequency range
8
9202
820
VSWR
Output level (avg) (I and Q
quad, 0dB VGA)
Gain flatness
1997 Sept 16
MHz
VCC–0.5
2:1
–1.5
TXLO and harmonics
Broadband noise power
MHz
1401
0.3VCC
VSWR
Alternate channel noise power
1
1040
101
Logic HIGH
Adjacent channel noise power
120
Max clock rate
DATA, CLOCK, STROBE, TXEN
Spurious output
dBm
2:1
Frequency range
Output level
AMPSTX
UNITS
MAX
-101
-13
VSWR (50Ω)
Serial interface (CMOS levels)
AMPS output, SE=1, AD=0, TXEN=1 (AC
couple)
TYP
MHz
2:1
0
+2
dBm
1
dB
Philips Semiconductors
Preliminary specification
I/Q transmit modulator
SA900
AC ELECTRICAL CHARACTERISTICS (continued)
SYMBOL
PARAMETER
TEST CONDITIONS
DUALTX
(cont.)
3rd order
Linearity (0dB VGA, I and Q inphase)
LIMITS
TYP
-35
-42
dBc
-55
dBc
5th order
7th order
-65
dBc
Carrier suppression (I and Q quadrature)
VGA = 0dB
-35
-45
dBc
Carrier suppression (I and Q quadrature)
VGA = –40dB
-28
-33
dBc
I and Q quadrature
-35
-45
dBc
869 to 894MHz
–104
dBm
824 to 849MHz
–47
dBc
2 to 824MHz
–41
dBc
849 to 869MHz
–41
dBc
894MHz to 8.49GHz
–41
dBc
Sideband suppression
Spurious output
TXLO and harmonics
Broadband noise (0dB VGA)
Q/Q
–21
dBc
869 to 894MHz
–136
dBm/Hz
935 to 960MHz
–136
dBm/Hz
Adjacent channel noise power
@30kHz
–95
dBc/Hz
Alternate channel noise power
@60kHz
–101
Max frequency
0.8
21
MHz
0.8
1.01
VP-P
0.8
21
MHz
0.8
1.01
VP-P
Baseband quadrature differential input
Differential modulation level
0.61
Differential input impedance
101
Max frequency
I/I
Baseband inphase differential input
Differential modulation level
0.61
Differential input impedance
10
Frequency range
900
Buffered TXLO differential outputs (AC
coupled)
LO_1/2
_
MAX
UNITS
MIN
kΩ
kΩ
1040
VSWR (single-ended)
2:1
single-ended
50
Output impedance
Output
Out
ut level
dBc/Hz
MHz
Ω
100
Ω
single-ended, 50Ω
50
90
mVP-P
differential, 100Ω
100
180
mVP-P
differential
NOTES:
1. Guaranteed by design.
2. Needs a different matching component. Max test frequency is 850MHz with test circuit shown in Figure 11.
mode function. The transition of the TXEN, from low to high turns
on the modulator. The falling edge of the TXEN signal disables the
synthesizer and modulator. The TXLO is a system supplied LO
signal. The SA900 buffers the TXLO signal (LO_1/2) for use with
the system synthesizer (such as the SA7025) to form the system LO
synthesizer loop. The DUAL mode can also be used for AMPS
operation. The AMPS and DUAL mode modulation is generated by
the system DSP IC to provide the required I/Q baseband modulation
for the SA900. The DUAL output provides low broadband noise
output power (so that the receiver sensitivity is not degraded) and
high linearity to meet cellular phone system needs. Table 1 provides
the VGA power control limits.
FUNCTIONAL DESCRIPTION
Dual Mode Operation
The SA900 transmit modulator provides direct single sideband
quadrature modulation of the difference of the TXLO and VCO
frequencies, while providing quadrature LO signals for the I/Q
modulator. The quadrature LO signals are modulated with high
linearity by the baseband inphase (I) and quadrature (Q) signals.
The summed modulator output produces the lower sideband, while
rejecting the upper sideband. The I and Q inputs also provide DC
biasing for the modulator inputs. The summed output of the
modulator goes to a variable gain amplifier (VGA) to control the
output level, it has 40.0dB of attenuation control range, with 0.63dB
steps. The power control function is programmed by means of a
6-bit word (see Table 3). The VGA output drives the power amp
output stage to provide +2dBm average minimum power level (at
0dB power control) into 50Ω, in conjunction with external matching
components on DUALTX. The AD (AMPS/DUAL) and the SE
(synthesizer enable) bit control the power up/down of the DUAL
1997 Sept 16
The SA900 DUALTX output is externally matched with either a shunt
inductor to VCC and a series capacitor or a shunt inductor to VCC
and a series inductor. This matches the DUALTX output to 50Ω.
Values of the matching components are dependent on PCB layout,
typical values are shown in Figure 9.
9
Philips Semiconductors
Preliminary specification
I/Q transmit modulator
SA900
the AMPS mode (AD=0) to a maximum of 6.4mA for the DUAL
mode (AD=1) by way of an external current setting resistor placed
from IPEAK to circuit ground. The typical loop filter network is shown
in Figure 5. The charge pump current output is programmed by
Table 1. VGA Power Control Limits
VGA
Min.
Typ.
Max.
Relative VGA
0
0
0
0
0
1
-1
-.63
-.2
0
2
-1
-.63
-.2
1
3
-1
-.63
-.2
2
4
-1
-.63
-.2
3
5
-1
-.63
-.2
4
6
-1
-.63
-.2
5
7
-1
-.63
-.2
6
where RSET is placed between IPEAK and GROUND.
15
-6.6
-5
-3
7
The PLL frequency is determined by
23
-6.6
-5
-3
15
31
-6.6
-5
-3
23
39
-6.6
-5
-3
31
47
-6.6
-5
-3
39
55
-6.6
-5
-3
47
63
-6.6
-5
-3
55
63
-43.2
-40.4
-37.2
0
AD 0
I OUT 6 AD 1
I OUT 24 VCO XO N 1.25V
R SET
1.25V
R SET
A8
)
1
B8
( )
1
(
where N=6, 7, 8, 9 and A8/1 and B8/1 are controlled by the AD bit
(AD=1 A8/1 and B8/1 are divide by 1, AD=0 A8/1 and B8/1 are
divide 8).
Table 2. Data Word Format
1. Guaranteed to be monotonic.
Mnemonics
Bits
A0
1 (MSB)
Address bit 0 (1)
A1
2
Address bit 1 (0)
A2
3
Address bit 2 (1)
A3
4
Address bit 4 (1)
PC0
5
Power control bit 0
PC1
6
Power control bit 1
PC2
7
Power control bit 2
PC3
8
Power control bit 3
PC4
9
Power control bit 4
PC5
10
Power control bit 5
N0
11
Divide N bit 0
Synthesizer Operation
N1
12
Divide N bit 1
The SA900 synthesizer is comprised of the differential VCO circuit,
with external tank components, the Gilbert cell multiplier phase
detector with programmable charge pump current, crystal oscillator
and programmable prescalers. The charge pump output drives an
external second order loop filter. The output of the loop filter is used
to provide the control voltage to the VCO tuning varactor to
complete the PLL synthesizer. The synthesized VCO output
frequency is mixed with the TXLO signal to generate the transmit LO
from the lower sideband (the difference of the VCO and TXLO
frequencies). The output of VCO is fed to a programmable /N
prescaler with user selectable divides of 6, 7, 8 and 9 (all divides
configured to provide 50% duty cycle). The output of the /N divider
drives the A8/1 prescaler. The A8/1 divide is selected by the AD
control bit (AD=1 for /1, and AD=0 for /8). The output of the divide
A8/1 is fed into one input of the phase detector. The reference input
for the phase comparator is generated from the crystal oscillator
(XO) output from the B8/1 prescaler. The B8/1 divide is selected by
the AD control bit (AD=0 for /8, and AD=1 for /1). The phase
detector compares the prescaled XO reference phase to the VCO
prescaled phase, to generate a charge pump output current
proportional to the phase error. The phase detector, a Gilbert cell
multiplier type, having a linear output from 0 to π (π/2 ± π/2). The
charge pump peak output current is programmable from 100µA for
AD
13
AMPS/DUAL mode select bit
SE
14
Synthesizer enable bit
NA
15
NA
SM1
16
Sleep mode 1 control bit
SM2
17
Sleep mode 2 control bit
X
18
Divide 3/1 control bit
AMPS Mode Operation
The SA900 can be configured to operate in the AMPS mode, where
FM modulation is applied to the SA900’s VCO. For the AMPS
mode, the VCO is configured with the proper synthesizer bandwidth
to allow the application of the AMPS modulation to the VCO varactor
tuned tank circuit. The modulated VCO signal is input into an image
reject mixer along with the TXLO signal, where the upper sideband
is rejected. This single sideband modulated signal then drives the
AMPS output power amplifier. The PA provides +2dBm power level
into 50Ω, with no external matching components required. The AD
(AMPS/DUAL) and the SE (synthesizer enable) bit control the power
up/down of the AMPS mode function. The transition of the TXEN
signal from low to high turns on the modulator. The falling edge of
TXEN signal disables the synthesizer and the modulator.
1997 Sept 16
Function
Y
19
Divide 2/1 control bit
NA
20
NA
NA
21
NA
NA
22
NA
NA
23
NA
NA
24 (LSB)
NA
VCO Operation
The VCO is designed to operate from 90MHz to 140MHz. The VCO
tank is configured using a parallel inductor and a dual common
cathode tuning varactor diodes. DC blocking capacitors are used to
isolate the varactor
10
Philips Semiconductors
Preliminary specification
I/Q transmit modulator
SA900
control voltage from the VCO tank DC bias voltages. The VCO
tuning voltage is generated from the output of the PLL loop filter.
The VCO tank configuration is shown in Figure 6.
AMPS/DUAL Mode
The A/D mode select enables or disables that portion of the circuitry
used for either the AMPS or DUAL mode of operation.
Crystal Oscillator (XO) Operation
AD
0
1
For cellular radio applications, the SA900 will most likely utilize an
external reference TCXO in order to provide the frequency stability
necessary to operate to system requirements. The output of the
system TCXO can be AC coupled to the XTAL_1 input. However,
for applications that do not require such accuracy the XO circuit can
be configured as a Colpitts type oscillator with the addition of two
external capacitors along with the reference crystal and a trim
capacitor as shown in Figure 7.
Synthesizer Enable
The SE bit turns on and off the synthesizer circuitry.
SE
0
1
Programmable Clock Outputs
The SM1 bit is used to power down the TXLO buffer, the divide 3/1
prescaler and the CLK1 output buffer.
SM1
0
1
The SM2 bit is used to power down the divide 2/1 prescaler and the
CLK2.
SM2
0
1
The SA900 is configured by means of a 3-wire input (CLOCK,
STROBE, DATA) to program the AMPS and DUAL modes, in
addition there are two power saving modes of operation, SLEEP and
STANDBY. The control logic section of the SA900 is designed using
low power CMOS logic. During SLEEP mode only the circuitry
required to provide a master clock (MCLK) to the digital portion of
the system is enabled. During the STANDBY mode of operation
MCLK, CLK1 and the TXLO and buffered LO outputs are powered
on, which may be the case when the system is in the receive only
mode. In the AMPS or DUAL operational modes all functions of the
SA900 are powered on to support receive, transmit and system
clock functions. The programming of the SA900 is identical to the
programming format of the SA7025 low-voltage 1GHz fractional-N
synthesizer, that can be used in conjunction with the SA900 to
provide the cellular radio channel selection.
A3
1
Divide By N
N1
0
0
1
1
1997 Sept 16
X
0
1
Operation
Divide 1
Divide 3
Y
0
1
Operation
Divide 1
Divide 2
Divide 2
Address
N0
0
1
0
1
Operation
Power down
Power up (with
SM1=1 normal
operation)
Divide 3
The programming data is structured as a 24 bit long serial data
word; the word includes 4 address bits (dedicated 1 0 1 1) for chip
select. Data bits are shifted in on the leading edge of the clock, with
the least significant bit (LSB) first and the most significant bit (MSB)
last. Table 2 shows data word format, the 15th and last 5 bits are
not used. Figure 8 shows the chip timing diagram.
A2
1
Operation
Power down
Power up (STANDBY)
Sleep Mode 2
Programming Operation
A1
0
Operation
Disabled
Enabled
Sleep Mode 1
The SA900 generates three buffered XO outputs used for external
reference signals. The XO feeds three sets of programmable
prescalers, the prescaler outputs are buffered to provide the CLK1,
CLK2 and MCLK signals. The CLK1 signal is a selectable divide 3/1
(X=1 divide 3, X=0 divide 1), 50% duty cycle, of the XO reference
signal. The CLK2 signal is a selectable divide 2/1 (Y=1 divide 2,
Y=0 divide 1), 50% duty cycle, of the XO reference signal. The
MCLK signal is a selectable divide 4/5/1 (CLKSET = VCC divide 4,
CLKSET = VCC/2 divide 5, and CLKSET = 0V divide 1), 50% duty
cycle, of the XO reference signal. MCLK is externally set by means
of the tri-level CLKSET input to provide a default master system
clock prior to programming the SA900.
A0
1
Mode
AMPS
DUAL
Divide
6
7
8
9
11
Philips Semiconductors
Preliminary specification
I/Q transmit modulator
SA900
Table 3. Power Control
Attenuation (dB)
PC0 (0.6dB)
PC1 (1.3dB)
PC2 (2.5dB)
PC3 (5.0dB)
PC4 (10.0dB)
PC5 (20.0dB)
0
0
0
0
0
0
0
0.6
1
0
0
0
0
0
1.3
0
1
0
0
0
0
1.9
1
1
0
0
0
0
2.5
0
0
1
0
0
0
3.2
1
0
1
0
0
0
3.8
0
1
1
0
0
0
4.4
1
1
1
0
0
0
5.0
0
0
0
1
0
0
5.7
1
0
0
1
0
0
6.3
0
1
0
1
0
0
23.3
1
0
1
0
0
1
1
1
1
1
1
1
•
•
•
•
•
•
39.7
Value
Component
Designator
DUAL Mode
AMPS Mode
R1
560Ω
560Ω
R2
1kΩ
5.6kΩ
C1
2.2nF
2.7µF
C2
No Load
.27µF
C3
33pF
6.8nF
RSET
15kΩ
75kΩ
Typical Filter Network
R2
PHSOUT
VCTRL
R1
C2
C3
C1
SR00640
Figure 5. PLL Loop Filter
(AMPS MODULATION)
C1
TANK_1
f
L1
C3
VCC
VCO
+
VR1
VCTRL
C1 = C2 = 33pF
[ 120MHz
C3 = 12pF
L1 = 82nH
1
2 ǸL1CȀ
CȀ + C3 )
C2
VR1 TOKO KV1470
ǒC11
)
1
1
)
C2
CVRI
Ǔ
*1
TANK_2
SR00641
Figure 6. VCO Tank Configuration
1997 Sept 16
12
Philips Semiconductors
Preliminary specification
I/Q transmit modulator
SA900
XTAL_1
C1
XO
CVAR
XTAL_2
C2
SR00642
Figure 7. Crystal Oscillator Configuration
TXEN
TRANSMIT ENABLED
LSB
DATA
MSB
CLOCK
T1
T2
T4
T3
STROBE
SYN_EN
SYNTHESIZER ENABLED
1
1
T1 T2 T3 , T4 3CLOCK
3CLOCK
SR00643
Figure 8. Chip Timing Diagram
VCC
VCC
100pF
100pF
1nF
1nF
L3
L1
L2
C1
1000pF
OR
34
SA900
34
SA900
TYPICAL VALUES
TYPICAL VALUES
50Ω
L1 = 39nH
L2 = 22nH
50Ω
L3 = 12nH
C1 = 1.5pF
SR00644
Figure 9. DUALTX Output Matching
1997 Sept 16
13
1997 Sept 16
C269
33pF
JMP
JMP
PHS-OUT
P1-14
JP5
VCO-TUNE
P1-15
JP4
J8
LO2PS1
14
Figure 10. SA900 Application Circuit
J2
XO-REF
T1-1
KK81
J18
VCO-REF
C265
NL
R333
1k
R258
1k
J1
TXLO2
R264
1k
P1-1,2,3
GND
Vcc
R266
560
D1
NL
R268
R260
51
R284
NL
R352
100
C371
100pF
C370 100pF
C263
.01uF
L252
100nH
5.6pF
1
C249
100pF
C247
100pF
C246
4.7uF
C253
+
C267
220pF
R274
0
C255
33pF
2
C254
33pF
ZO=50
KV1470
1
W3
P1-4,5,6,11,12,13
J7
LO2PS2
1
W1
C283
NL
W2
2
2
1
2
3
4
5
6
7
8
9
10
11
12
NL
R279
C243
100pF
P2
CLK1
R293
NL
NL
C299
C292
NL
C289
NL
P3
CLK1
L290
NL
36
35
34
33
32
31
30
29
28
27
26
25
C294
NL
R297
NL
L296
NL
C295
NL
Vcc
GND
DUALTX
GND
Vcc
AMPSTX
GND
Vcc
GND
Vcc
Vcc
GND
P4
MCLK
C288
.010uF
1 11 11 11 22 22 2
3 45 67 89 01 23 4
C
S
X
L CT
T C C MK D L R T
A V L GL GC S A OOX
L c KNK NL ET CBE
1 c 1 D2 DKT AKEN
V L L GV I I QQGV G
c OON c 1 2 1 2 N c N
c 2 1 Dc
Dc D
4 44 44 44 44 33 3
8 76 54 32 10 98 7
C287
.010uF
GND
TXLO2
TXLO1
GND
Vcc
TANK1
TANK2
Vcc
PHS OUT
IPEAK
GND
XTAL1
U1
SA900BE
C314
100pF
C313
100pF
C245
.010uF
2
1
JP3 JMP
JP2 JMP
JP1 JMP
P1-10
TXENABLE
P1-9
STROBE
P1-8
CLOCK
P1-7
DATA
C242
100pF
W5
C301
100pF
C305
100pF
ZO=50
J4
Q1
C300
.010uF
1
L372
22nH
L304
39nH
C241
100PF
C312
100pF
J3
Q2
J5
I2
2
R350
100k
R349
100k
J10
AMPSTXRF
ZO=50
W4
C306
.010uF
J6
I1
J9
DIGTXRF
I/Q transmit modulator
C282
NL
L280
NL
C281
.010uF
R262
15k
ZO=50
ZO=50
Philips Semiconductors
Preliminary specification
SA900
NOTE:
VCO-REF circuit is optional
L372 is C307 on the PCB
C246 combines C240 and C244 on the PCB
SR00645
1997 Sept 16
Figure 11. SA900 Test Circuit
15
XO-REF
PHASE OUT
T1-1
KK81
TANK–1
TXLO2
W3
2
+
R260
51
1K
R300
1K
C371
100pF
C370 100pF
ZO=50
C280
1000pF
1
GND
Vcc
R301
C263
.01uF
R262
24K
C249
100pF
C247
270pF
C246
1000pF
LO_1
2
ZO=50
LO_2
2
C314
270pF
R304
4.7K
C402
7pF
C401
7pF
R305
4.7K
S
C
X
L CT
T C C MKDL R T
A V L G L G C SA OOX
L c K N K N L ET CB E
1 c 1 D 2 D KTAKEN
1 11 11 11 22 22 2
3 45 67 89 01 23 4
SA900
V L L GV I I QQGV G
c OON c 1 2 1 2 N c N
c 2 1 Dc
Dc D
4 44 44 44 44 33 3
8 76 54 32 10 98 7
C400
7pF
R303
4.7K
GND
TXLO2
TXLO1
GND
Vcc
TANK1
TANK2
Vcc
PHS OUT
IPEAK
GND
XTAL1
CLOCK2
CLOCK1
C243
100pF
1
2
3
4
5
6
7
8
9
10
11
12
1
C315
270pF
ZO=50
1
36
35
34
33
32
31
30
29
28
27
26
25
MCLK
Vcc
GND
DUALTX
GND
Vcc
AMPSTX
GND
Vcc
GND
Vcc
Vcc
GND
Q1
C305
100pF
TXENABLE
1
1
C245
.010uF
C312
100pF
C301
100pF
C300
.010uF
L372
22nH
L304
39nH
C241
100PF
STROBE
CLOCK
DATA
CLKSET
C242
100pF
Q2
I2
ZO=50
ZO=50
C306
.010uF
I1
2
2
AMPSTX
DIGTXRF
Philips Semiconductors
Preliminary specification
I/Q transmit modulator
SA900
SR00646
Philips Semiconductors
Preliminary specification
I/Q transmit modulator
SA900
PERFORMANCE CHARACTERISTICS
–16.00
3.50
3.00
–17.00
POWER (dBm)
POWER (dBm)
4.00
VCC = 3.9V
VCC = 4.0V
VCC = 4.5V
–16.50
–17.50
–18.00
2.50
2.00
1.50
T = +85°C
T = +27°C
T = –45°C
1.00
0.50
–18.50
–19.00
900
0.00
–0.50
970
–1.00
1040
820
FREQUENCY (MHz)
LO Buffer vs. Frequency (27°C, TXLO = –10dBm)
VCC = 3.9V
VCC = 4.0V
VCC = 4.5V
2.80
2.60
2.80
2.40
VCC = 4.5V
VCC = 3.9V
VCC = 4.0V
2.20
2.00
POWER (dBm)
POWER (dBm)
860
AMPTX vs. Frequency (VCC = 4.0V, TXLO = –10dBm)
3.00
1.80
1.60
1.40
1.20
1.00
820
836
FREQUENCY (MHz)
2.60
2.40
2.20
860
AMPTX vs. Frequency (27°C, TXLO = –10dBm)
2.00
820
3.50
836
FREQUENCY (MHz)
850
DUALTX vs. Frequency (TEMP 27°C, TXLO = –10dBm)
3.00
2.50
2.00
72
VCC = –40°C
VCC = 27°C
VCC = 85°C
1.50
1.00
0.50
0.00
820
836
850
FREQUENCY (MHz)
CURRENT (AMPERES)
POWER (dBm)
836
FREQUENCY (MHz)
DUALTX vs. Frequency (VCC = 4.0V, TXLO = –10dBm)
70
68
66
64
VCC = 4.5V
VCC = 4.0V
VCC = 3.9V
62
–16.00
T = +85°C
T = +27°C
T = –45°C
POWER (dBm)
–16.50
60
–40
27
–17.00
TEMPERATURE (°C)
–17.50
DUAL ICC vs. Temperature
85
–18.00
–18.50
–19.00
–19.50
–20.00
900
970
1040
FREQUENCY (MHz)
LO Buffer vs. Frequency (VCC = 4.0V, TXLO = –10dBm)
SR00647
Figure 12. Performance Characteristics
1997 Sept 16
16
Philips Semiconductors
Preliminary specification
I/Q transmit modulator
SA900
PERFORMANCE CHARACTERISTICS
–44.50
VCC = –40°C
VCC = 85°C
VCC = 27°C
SUPPRESSION (dBc)
–44.00
–44.50
–45.00
–45.50
–46.00
SUPPRESSION (dBc)
–43.00
–43.50
–45.50
–46.00
–46.50
–47.00
–46.50
–47.00
–47.50
820
–47.50
820
836
–34.00
–32
–33
VCC = –85°C
VCC = –40°C
VCC = 27°C
–38.00
VCC = 3.9V
VCC = 4.0V
VCC = 4.5V
–34
–35
–36
dBc
–40.00
–37
–42.00
–38
–39
–44.00
–40
–46.00
–41
–42
–40
–48.00
820
836
850
85
27
TEMPERATURE (°C)
FREQUENCY (MHz)
DUALTX 3rd Order Products vs Temperature
(TXLO = –10dBm, f = 836MHz, 0dB VGA I/Q Inphase)
DUALTX Sideband Suppression vs Frequency
(VCC = 4.0V, TXLO = –10dBm Single Sideband
Mode, With Respect to Lower Sideband)
–30.00
–30.00
VCC = 3.9V
VCC = 4.0V
VCC = 4.5V
T = +85°C
T = +27°C
T = –45°C
–35.00
ATTENUATION (dB)
–35.00
ATTENUATION (dB)
850
DUALTX Sideband Suppression vs. Frequency
(Temperature = 27°C, TXLO = –10dBm Single
Sideband Mode, With Respect to Lower Sideband)
FREQUENCY (MHz)
–36.00
836
FREQUENCY (MHz)
850
DUALTX Carrier Suppression vs. Frequency
(VCC = 4.0, TXLO = –10dBm Single Sideband Mode,
With Respect to Lower Sideband)
SUPPRESSION (dBc)
VCC = 4.5V
VCC = 4.0V
VCC = 3.9V
–45.00
–40.00
–45.00
–40.00
–45.00
–50.00
–55.00
–50.00
–60.00
–55.00
0 2 5 7 10 13 15 18 20 23 25 26 29 33 37 40 44 48 51 55 59 63
0 2 5 7 10 13 15 18 20 23 25 26 29 33 37 40 44 48 51 55 59 63
VGA 6-BIT WORD VALUE (LSBs)
VGA 6-BIT WORD VALUE (LSBs)
DUALTX Carrier Suppression vs VGA Range
(VCC = 4.0V, f = 836MHz, TXLO = –10dBm)
DUALTX Carrier Suppression vs VGA Range
(27°C, f = 836MHz, TXLO = –10dBm)
SR00648
Figure 13. Performance Characteristics
1997 Sept 16
17
Philips Semiconductors
Preliminary specification
I/Q transmit modulator
SA900
PERFORMANCE CHARACTERISTICS
0
–5
ATTENUATION (dB)
–10
–15
27°C
–20
–40°C
–25
85°C
–30
–35
–40
–45
0
4
2
6
8
10 12 14 16 18
20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60
62
VGA 6-BIT WORD VALUE (LSBs)
DUALTX VGA Attenuation Profile vs. Temperature (VCC = 4.0V, F = 836MHz)
0
–5
–10
3.9V
ATTENUATION (dB)
–15
4.0V
–20
4.6V
–25
–30
–35
–40
–45
0
2
4
6
8
10 12 14 16 18
20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60
62
VGA 6-BIT WORD VALUE (LSBs)
DUALTX VGA Attenuation Profile vs. VCC (T = 27°C, F = 836MHz)
SR00649
Figure 14. Performance Characteristics
1997 Sept 16
18
Philips Semiconductors
Preliminary specification
I/Q transmit modulator
SA900
LQFP48: plastic low profile quad flat package; 48 leads; body 7 x 7 x 1.4 mm
1997 Sept 16
19
SOT313-2
Philips Semiconductors
Preliminary specification
I/Q transmit modulator
SA900
DEFINITIONS
Data Sheet Identification
Product Status
Definition
Objective Specification
Formative or in Design
This data sheet contains the design target or goal specifications for product development. Specifications
may change in any manner without notice.
Preliminary Specification
Preproduction Product
This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips
Semiconductors reserves the right to make changes at any time without notice in order to improve design
and supply the best possible product.
Product Specification
Full Production
This data sheet contains Final Specifications. Philips Semiconductors reserves the right to make changes
at any time without notice, in order to improve design and supply the best possible product.
Philips Semiconductors and Philips Electronics North America Corporation reserve the right to make changes, without notice, in the products,
including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips
Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright,
or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask
work right infringement, unless otherwise specified. Applications that are described herein for any of these products are for illustrative purposes
only. Philips Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing
or modification.
LIFE SUPPORT APPLICATIONS
Philips Semiconductors and Philips Electronics North America Corporation Products are not designed for use in life support appliances, devices,
or systems where malfunction of a Philips Semiconductors and Philips Electronics North America Corporation Product can reasonably be expected
to result in a personal injury. Philips Semiconductors and Philips Electronics North America Corporation customers using or selling Philips
Semiconductors and Philips Electronics North America Corporation Products for use in such applications do so at their own risk and agree to fully
indemnify Philips Semiconductors and Philips Electronics North America Corporation for any damages resulting from such improper use or sale.
Philips Semiconductors
811 East Arques Avenue
P.O. Box 3409
Sunnyvale, California 94088–3409
Telephone 800-234-7381
Philips Semiconductors and Philips Electronics North America Corporation
register eligible circuits under the Semiconductor Chip Protection Act.
 Copyright Philips Electronics North America Corporation 1996
All rights reserved. Printed in U.S.A.
1997 Sept 16
20