PHILIPS PCA9533D01

INTEGRATED CIRCUITS
PCA9533
4-bit I2C LED dimmer
Product data sheet
Supersedes data of 2003 Sep 19
Philips
Semiconductors
2004 Oct 01
Philips Semiconductors
Product data sheet
4-bit I2C LED dimmer
PCA9533
the duty cycle to vary the amount of time the LED is on and thus the
average current through the LED.
The initial setup sequence programs the two blink rates/duty cycles
for each individual PWM. From then on, only one command from the
bus master is required to turn individual LEDs ON, OFF, BLINK
RATE 1 or BLINK RATE 2. Based on the programmed frequency
and duty cycle, BLINK RATE 1 and BLINK RATE 2 will cause the
LEDs to appear at a different brightness or blink at periods up to
1.69 second. The open drain outputs directly drive the LEDs with
maximum output sink current of 25 mA per bit and 100 mA per
package.
FEATURES
• 4 LED drivers (on, off, flashing at a programmable rate)
• 2 selectable, fully programmable blink rates (frequency and duty
To blink LEDs at periods greater than 1.69 second the bus master
(MCU, MPU, DSP, chipset, etc.) must send repeated commands to
turn the LED on and off as is currently done when using normal I/O
Expanders like the Philips PCF8574 or PCA9554. Any bits not used
for controlling the LEDs can be used for General Purpose Parallel
Input/Output (GPIO) expansion which provides a simple solution
when additional I/O is needed for ACPI power switches, sensors,
pushbuttons, alarm monitoring, fans, etc.
cycle) between 0.591 Hz and 152 Hz (1.69 seconds and
6.58 milliseconds)
• 256 brightness steps
• Input/outputs not used as LED drivers can be used as regular
GPIOs
• Internal oscillator requires no external components
• I2C interface logic compatible with SMBus
• Internal power-on reset
• Noise filter on SCL/SDA inputs
• 4 open drain outputs directly drive LEDs to 25 mA
• Edge rate control on outputs
• No glitch on power-up
• Supports hot insertion
• Low stand-by current
• Operating power supply voltage range of 2.3 V to 5.5 V
• 0 to 400 kHz clock frequency
• ESD protection exceeds 2000 V HBM per JESD22-A114,
Power-On Reset (POR) initializes the registers to their default state
causing the bits to be set HIGH (LED off).
Due to pin limitations, the PCA9533 is not featured with hardware
address pins. The PCA9533/01 and the PCA9533/02 have different
fixed I2C addresses allowing operation of both on the same bus.
PIN CONFIGURATION
LED0
1
8
VDD
LED1
2
7
SDA
LED2
3
6
SCL
VSS
4
5
LED3
SW01035
Figure 1. Pin configuration
150 V MM per JESD22-A115 and 1000 V CDM per JESD22-C101
• Latch-up testing is done to JEDEC Standard JESD78 which
PIN DESCRIPTION
exceeds 100 mA
PIN
NUMBER
SYMBOL
1
LED0
LED driver 0
DESCRIPTION
2
LED1
LED driver 1
The PCA9533 is a 4-bit I2C and SMBus I/O expander optimized for
dimming LEDs in 256 discrete steps for Red/Green/Blue (RGB)
color mixing and back light applications.
3
LED2
LED driver 2
4
VSS
5
LED3
LED driver 3
6
SCL
Serial clock line
7
SDA
Serial data line
8
VDD
Supply voltage
• Packages offered: SO8, TSSOP8 (MSOP8)
The PCA9533 contains an internal oscillator with two user
programmable blink rates and duty cycles coupled to the output
PWM. The LED brightness is controlled by setting the blink rate high
enough (> 100 Hz) that the blinking cannot be seen and then using
2004 Oct 01
2
FUNCTION
Supply ground
Philips Semiconductors
Product data sheet
4-bit I2C LED dimmer
PCA9533
ORDERING INFORMATION
PACKAGES
TEMPERATURE RANGE
ORDER CODE
TOPSIDE MARK
DRAWING NUMBER
8-Pin Plastic SO
–40 °C to +85 °C
PCA9533D/01
P9533/1
SOT96-1
8-Pin Plastic SO
–40 °C to +85 °C
PCA9533D/02
P9533/2
SOT96-1
8-Pin Plastic TSSOP
–40 °C to +85 °C
PCA9533DP/01
P33/1
SOT505-1
8-Pin Plastic TSSOP
–40 °C to +85 °C
PCA9533DP/02
P33/2
SOT505-1
Standard packing quantities and other packaging data are available at www.standardproducts.philips.com/packaging.
I2C is a trademark of Philips Semiconductors Corporation.
BLOCK DIAGRAM
PCA9533
INPUT
REGISTER
SCL
INPUT
FILTERS
I2C-BUS
CONTROL
LED SELECT (LSx)
REGISTER
SDA
0
1
VDD
LEDx
POWER-ON
RESET
OSCILLATOR
PRESCALER 0
REGISTER
PWM0
REGISTER
BLINK0
PRESCALER 1
REGISTER
PWM1
REGISTER
BLINK1
VSS
SW02046
NOTE: ONLY ONE I/O SHOWN FOR CLARITY
Figure 2. Block diagram
2004 Oct 01
3
Philips Semiconductors
Product data sheet
4-bit I2C LED dimmer
PCA9533
DEVICE ADDRESSING
CONTROL REGISTER DEFINITION
Following a START condition the bus master must output the
address of the slave it is accessing. The address of the PCA9533/01
is shown in Figure 3 and PCA9533/02 in Figure 4.
SLAVE ADDRESS
1
1
0
0
0
1
0
R/W
SW01037
Figure 3. Slave address — PCA9533/01
B2
B1
B0
REGISTER
NAME
TYPE
REGISTER
FUNCTION
0
0
0
INPUT
READ
INPUT
REGISTER
0
0
1
PSC0
READ/
WRITE
FREQUENCY
PRESCALER 0
0
1
0
PWM0
READ/
WRITE
PWM
REGISTER 0
0
1
1
PSC1
READ/
WRITE
FREQUENCY
PRESCALER 1
1
0
0
PWM1
READ/
WRITE
PWM
REGISTER 1
1
0
1
LS0
READ/
WRITE
LED SELECTOR
SLAVE ADDRESS
1
1
0
0
0
1
1
R/W
SW01038
Figure 4. Slave address — PCA9533/02
REGISTER DESCRIPTION
INPUT — INPUT REGISTER
The last bit of the address byte defines the operation to be
performed. When set to logic 1 a read is selected while a logic 0
selects a write operation.
LED
3
CONTROL REGISTER
Following the successful acknowledgement of the slave address,
the bus master will send a byte to the PCA9533 which will be stored
in the Control Register.
0
0
0
AI
0
B2
B1
LED
1
LED
0
bit
7
6
5
4
3
2
1
0
Default
0
0
0
0
X
X
X
X
The INPUT register reflects the state of the device pins. Writes to
this register will be acknowledged but will have no effect.
NOTE: The default value “X” is determined by the externally applied
logic level, normally ‘1’ when used for directly driving LED with
pull-up to VDD.
B0
PSC0 — FREQUENCY PRESCALER 0
REGISTER ADDRESS
RESET STATE: 00h
LED
2
AUTO-INCREMENT FLAG
bit
7
6
5
4
3
2
1
0
default
0
0
0
0
0
0
0
0
SW01034
PSC0 is used to program the period of the PWM output.
Figure 5. Control register
The period of BLINK0 +
The lowest 3 bits are used as a pointer to determine which register
will be accessed.
(PSC0 ) 1)
152
PWM0 — PWM REGISTER 0
If the auto-increment flag is set, the three low order bits of the
Control Register are automatically incremented after a read or write.
This allows the user to program the registers sequentially. The
contents of these bits will rollover to ‘000’ after the last register is
accessed.
bit
7
6
5
4
3
2
1
0
default
1
0
0
0
0
0
0
0
The PWM0 register determines the duty cycle of BLINK0. The
outputs are LOW (LED on) when the count is less than the value in
PWM0 and HIGH (LED off) when it is greater. If PWM0 is
programmed with 00h, then the PWM0 output is always HIGH
(LED off) .
When auto-increment flag is set (AI = 1) and a read sequence is
initiated, the sequence must start by reading a register different from
the input register (B2 B1 B0 0 0 0 0).
The duty cycle of BLINK0 is: PWM0
256
Only the 3 least significant bits are affected by the AI flag.
PSC1 — FREQUENCY PRESCALER 1
Unused bits must be programmed with zeroes.
bit
7
6
5
4
3
2
1
0
default
0
0
0
0
0
0
0
0
PSC1 is used to program the period of PWM output.
The period of BLINK1 +
2004 Oct 01
4
(PSC1 ) 1)
152
Philips Semiconductors
Product data sheet
4-bit I2C LED dimmer
PCA9533
PWM1 — PWM REGISTER 1
PINS USED AS GENERAL PURPOSE I/Os
bit
7
6
5
4
3
2
1
0
default
1
0
0
0
0
0
0
0
LED pins not used to control LEDs can be used as general purpose
I/Os.
For use as input: Set LEDx to high-impedance (00) and then read
the pin state via the input register.
The PWM1 register determines the duty cycle of BLINK1. The
outputs are LOW (LED on) when the count is less than the value in
PWM1 and HIGH (LED off) when it is greater. If PWM1 is
programmed with 00h, then the PWM1 output is always HIGH
(LED off).
For use as output: Connect external pull-up resistor to the pin and
size it according to the DC recommended operating characteristics.
LED output pin is HIGH when the output is programmed as
high-impedance, and LOW when the output is programmed LOW
through the “LED selector” register. The output can be pulse-width
controlled when PWM0 or PWM1 are used.
The duty cycle of BLINK1 is: PWM1
256
LS0 — LED SELECTOR
LED3
LED2
LED 1
LED 0
bit
7
6
5
4
3
2
1
0
POWER-ON RESET
default
0
0
0
0
0
0
0
0
When power is applied to VDD, an internal Power-On Reset holds
the PCA9533 in a reset condition until VDD has reached VPOR. At
this point, the reset condition is released and the PCA9533 registers
are initialized to their default states, with all outputs in the off state.
Thereafter, VDD must be lowered below 0.2 V to reset the device.
The LSx LED select registers determine the source of the LED data.
00 = Output is set Hi-Z (LED off – default)
01 = Output is set LOW (LED on)
10 = Output blinks at PWM0 rate
11 = Output blinks at PWM1 rate
2004 Oct 01
5
Philips Semiconductors
Product data sheet
4-bit I2C LED dimmer
PCA9533
CHARACTERISTICS OF THE I2C-BUS
Start and stop conditions
The I2C-bus is for 2-way, 2-line communication between different ICs
or modules. The two lines are a serial data line (SDA) and a serial
clock line (SCL). Both lines must be connected to a positive supply
via a pull-up resistor when connected to the output stages of a device.
Data transfer may be initiated only when the bus is not busy.
Both data and clock lines remain HIGH when the bus is not busy. A
HIGH-to-LOW transition of the data line, while the clock is HIGH is
defined as the start condition (S). A LOW-to-HIGH transition of the
data line while the clock is HIGH is defined as the stop condition (P)
(see Figure 7).
Bit transfer
System configuration
One data bit is transferred during each clock pulse. The data on the
SDA line must remain stable during the HIGH period of the clock
pulse as changes in the data line at this time will be interpreted as
control signals (see Figure 6).
A device generating a message is a transmitter: a device receiving
is the receiver. The device that controls the message is the master
and the devices which are controlled by the master are the slaves
(see Figure 8).
SDA
SCL
data line
stable;
data valid
change
of data
allowed
SW00363
Figure 6. Bit transfer
SDA
SDA
SCL
SCL
S
P
START condition
STOP condition
SW00365
Figure 7. Definition of start and stop conditions
SDA
SCL
MASTER
TRANSMITTER/
RECEIVER
SLAVE
RECEIVER
SLAVE
TRANSMITTER/
RECEIVER
MASTER
TRANSMITTER
MASTER
TRANSMITTER/
RECEIVER
I2C
MULTIPLEXER
SLAVE
SW00366
Figure 8. System configuration
2004 Oct 01
6
Philips Semiconductors
Product data sheet
4-bit I2C LED dimmer
PCA9533
Acknowledge
The number of data bytes transferred between the start and the stop conditions from transmitter to receiver is not limited. Each byte of eight bits
is followed by one acknowledge bit. The acknowledge bit is a HIGH level put on the bus by the transmitter whereas the master generates an
extra acknowledge related clock pulse.
A slave receiver which is addressed must generate an acknowledge after the reception of each byte. Also a master must generate an
acknowledge after the reception of each byte that has been clocked out of the slave transmitter. The device that acknowledges has to pull down
the SDA line during the acknowledge clock pulse, so that the SDA line is stable LOW during the HIGH period of the acknowledge related clock
pulse, set-up and hold times must be taken into account.
A master receiver must signal an end of data to the transmitter by not generating an acknowledge on the last byte that has been clocked out of
the slave. In this event, the transmitter must leave the data line HIGH to enable the master to generate a stop condition.
DATA OUTPUT
BY TRANSMITTER
not acknowledge
DATA OUTPUT
BY RECEIVER
acknowledge
SCL FROM
MASTER
1
2
8
9
S
clock pulse for
acknowledgement
START condition
SW00368
Figure 9. Acknowledgement on the
2004 Oct 01
7
I2C-bus
Philips Semiconductors
Product data sheet
4-bit I2C LED dimmer
PCA9533
Bus transactions
1
SCL
2
3
4
5
6
7
8
9
command byte
slave address
SDA
S
1
1
0
0
0
1
0
0
start condition
R/W
A
0
0
0
AI
0
data to register
B2
B1
B0
acknowledge
from slave
DATA 1
A
A
acknowledge
from slave
acknowledge
from slave
WRITE TO
REGISTER
DATA OUT
FROM PORT
DATA 1 VALID
tpv
SW02002
Figure 10. WRITE to register
acknowledge
from slave
slave address
S
1
1
0
0
0
1
0
0
A
acknowledge
from slave
0
0
0
AI
0
B2 B1 B0
A
S
acknowledge
from slave
slave address
1
1
0
0
0
1
R/W
0
1
acknowledge
from master
data from register
DATA
A
A
first byte
R/W
auto-increment
register address
if AI = 1
at this moment master-transmitter
becomes master-receiver and
slave-receiver becomes
slave-transmitter
data from register
no acknowledge
from master
NA
DATA
P
last byte
SW02001
Figure 11. READ from register
slave address
SDA
S
1
1
0
0
0
start condition
data from port
1
0
1
R/W
data from port
DATA 1
A
A
acknowledge
from slave
DATA 4
acknowledge
from master
NA
no acknowledge
from master
P
stop
condition
READ FROM
PORT
DATA INTO
PORT
DATA 1
DATA 2
DATA 3
tph
DATA 4
tps
SW01097
NOTES:
1. This figure assumes the command byte has previously been programmed with 00h.
2. PCA9533/01 shown.
Figure 12. READ input port register
2004 Oct 01
8
Philips Semiconductors
Product data sheet
4-bit I2C LED dimmer
PCA9533
APPLICATION DATA
5V
5V
10 kΩ
10 kΩ
VDD
SDA
SDA
LED0
SCL
SCL
LED1
LED2
LED3
I2C/SMBus MASTER
VSS
PCA9533
SW02047
Figure 13. Typical application
Minimizing IDD when the I/O is used to control LEDs
When the I/Os are used to control LEDs, they are normally connected to VDD through a resistor as shown in Figure 13. Since the LED acts as a
diode, when the LED is off the I/O VIN is about 1.2 V less than VDD. The supply current, IDD, increases as VIN becomes lower than VDD and is
specified as ∆IDD in the DC characteristics table.
Designs needing to minimize current consumption, such as battery power applications, should consider maintaining the I/O pins greater than or
equal to VDD when the LED is off. Figure 14 shows a high value resistor in parallel with the LED. Figure 15 shows VDD less than the LED supply
voltage by at least 1.2 V. Both of these methods maintain the I/O VIN at or above VDD and prevents additional supply current consumption when
the LED is off.
3.3 V
VDD
LED
100 kΩ
VDD
VDD
LEDx
LED
LEDx
SW02086
SW02087
Figure 14. High value resistor in parallel with the LED
2004 Oct 01
5V
Figure 15. Device supplied by a lower voltage
9
Philips Semiconductors
Product data sheet
4-bit I2C LED dimmer
PCA9533
Programming example
The following example will show how to set LED0 and LED1 off. It
will set LED2 to blink at 1 Hz, 50 % duty cycle. LED3 will be set to
be dimmed at 25 % of their maximum brightness
(duty cycle = 25 %). PCA9533/01 is used in this example.
Table 1.
I2C-bus
Start
S
PCA9533 address
C4h
PSC0 subaddress + auto-increment
11h
Set prescaler PSC0 to achieve a period of 1 second:
1
Blink period 1 PSC0
152
PSC0 = 151
97h
Set PWM0 duty cycle to 50 %:
PWM0 0.5
256
80h
PWM0 = 128
Set prescaler PWM1 to dim at maximum frequency
00h
Blink period maximum
PSC1 = 0
Set PWM1 output duty cycle to 25 %:
PWM1 0.25
256
PWM1 = 64
40h
Set LED0 on, LED1 off, LED2 set to blink at PSC0,
PWM0, LED3 set to blink at PCS1, PWM1
E1h
Stop
P
2004 Oct 01
10
Philips Semiconductors
Product data sheet
4-bit I2C LED dimmer
PCA9533
ABSOLUTE MAXIMUM RATINGS
In accordance with the Absolute Maximum Rating System (IEC 134)
PARAMETER
SYMBOL
CONDITIONS
MIN
MAX
UNIT
–0.5
6.0
V
VDD
Supply voltage
VI/O
DC voltage on an I/O
VSS – 0.5
5.5
V
II/O
DC output current on an I/O
—
+25
mA
ISS
Supply current
—
100
mA
Ptot
Total power dissipation
—
400
mW
Tstg
Storage temperature range
–65
+150
°C
Tamb
Operating ambient temperature
–40
+85
°C
HANDLING
Inputs and outputs are protected against electrostatic discharge in normal handling. However, to be totally safe, it is desirable to take
precautions appropriate to handling MOS devices. Advice can be found in Data Handbook IC24 under “Handling MOS devices”.
DC CHARACTERISTICS
VDD = 2.3 V to 5.5 V; VSS = 0 V; Tamb = –40 °C to +85 °C; unless otherwise specified. TYP at 3.3 V and 25 °C.
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNIT
2.3
—
5.5
V
Supplies
VDD
Supply voltage
IDD
Supply current
Operating mode; VDD = 5.5 V; no load;
VI = VDD or VSS; fSCL = 100 kHz
—
350
500
µA
Istb
Standby current
Standby mode; VDD = 5.5 V; no load;
VI = VDD or VSS; fSCL = 0 kHz
—
1.9
3.0
µA
∆IDD
Additional standby current
Standby mode; VDD = 5.5 V; Every
LED I/O at VIN = 4.3 V; fSCL = 0 kHz
—
—
325
µA
VPOR
Power-on reset voltage (Note 1)
No load; VI = VDD or VSS
—
1.7
2.2
V
–0.5
—
0.3VDD
V
Input SCL; input/output SDA
VIL
LOW-level input voltage
VIH
HIGH-level input voltage
0.7VDD
—
5.5
V
IOL
LOW-level output current
VOL = 0.4 V
3
6.5
—
mA
IL
Leakage current
VI = VDD = VSS
–1
—
+1
µA
CI
Input capacitance
VI = VSS
—
3.7
5
pF
VIL
LOW-level input voltage
–0.5
—
0.8
V
VIH
HIGH-level input voltage
2.0
—
5.5
V
VOL = 0.4 V; VDD = 2.3 V; Note 2
9
—
—
mA
VOL = 0.4 V; VDD = 3.0 V; Note 2
12
—
—
mA
VOL = 0.4 V; VDD = 5.0 V; Note 2
15
—
—
mA
VOL = 0.7 V; VDD = 2.3 V; Note 2
15
—
—
mA
VOL = 0.7 V; VDD = 3.0 V; Note 2
20
—
—
mA
VOL = 0.7 V; VDD = 5.0 V; Note 2
25
—
—
mA
VDD = 3.6 V; VI = 0 V or VDD
–1
—
1
µA
—
2.1
5
pF
I/Os
IOL
O
IL
CIO
LOW level output current
LOW-level
Input leakage current
Input/output capacitance
NOTES:
1. VDD must be lowered to 0.2 V in order to reset part.
2. Each I/O must be externally limited to a maximum of 25 mA and the device must be limited to a maximum current of 100 mA.
2004 Oct 01
11
Philips Semiconductors
Product data sheet
4-bit I2C LED dimmer
PCA9533
AC SPECIFICATIONS
SYMBOL
STANDARD MODE
I2C-BUS
PARAMETER
fSCL
Operating frequency
tBUF
FAST MODE
I2C-BUS
UNITS
MIN
MAX
MIN
MAX
0
100
0
400
kHz
Bus free time between STOP and START conditions
4.7
—
1.3
—
µs
tHD;STA
Hold time after (repeated) START condition
4.0
—
0.6
—
µs
tSU;STA
Repeated START condition setup time
4.7
—
0.6
—
µs
tSU;STO
Setup time for STOP condition
4.0
—
0.6
—
µs
tHD;DAT
Data in hold time
0
—
0
—
ns
tVD;ACK
—
600
—
600
ns
tVD;DAT (L)
Data out valid time3
—
600
—
600
ns
tVD;DAT (H)
Data out valid time3
—
1500
—
600
ns
tSU;DAT
Valid time for ACK
condition2
Data setup time
250
—
100
—
ns
tLOW
Clock LOW period
4.7
—
1.3
—
µs
tHIGH
Clock HIGH period
4.0
—
0.6
—
µs
1
tF
Clock/Data fall time
—
300
20 + 0.1 Cb
300
ns
tR
Clock/Data rise time
—
1000
20 + 0.1 Cb1
300
ns
tSP
Pulse width of spikes that must be suppressed by the
input filters
—
50
—
50
ns
ns
Port Timing
tPV
Output data valid
—
200
—
200
tPS
Input data setup time
100
—
100
—
ns
tPH
Input data hold time
1
—
1
—
µs
NOTES:
1. Cb = total capacitance of one bus line in pF.
2. tVD;ACK = time for Acknowledgement signal from SCL LOW to SDA (out) LOW.
3. tVD;DAT = minimum time for SDA data out to be valid following SCL LOW.
2004 Oct 01
12
Philips Semiconductors
Product data sheet
4-bit I2C LED dimmer
PCA9533
+20%
MAX
+10%
0%
PERCENT
VARIATION
–10%
AVG
–20%
–30%
MIN
–40%
–40
0
+25
+70
+85
TEMPERATURE
(°C)
SW02311
Figure 16. Typical frequency variation over process at VDD = 2.3 V to 3.0 V
+20%
MAX
+10%
0%
PERCENT
VARIATION
AVG
–10%
–20%
MIN
–30%
–40%
–40
0
+25
+70
+85
TEMPERATURE
(°C)
Figure 17. Typical frequency variation over process at VDD = 3.0 V to 5.5 V
2004 Oct 01
13
SW02312
Philips Semiconductors
Product data sheet
4-bit I2C LED dimmer
PCA9533
SDA
tBUF
tR
tLOW
tF
tHD;STA
tSP
SCL
tHD;STA
P
tSU;STA
tHD;DAT
S
tHIGH
tSU;DAT
tSU;STO
Sr
P
SU00645
Figure 18. Definition of timing
BIT 7
MSB
(A7)
START
CONDITION
(S)
PROTOCOL
t
t
SU;STA
LOW
BIT 6
(A6)
t HIGH
BIT 7
(D1)
BIT 8
(D0)
ACKNOWLEDGE
(A)
STOP
CONDITION
(P)
1 / f SCL
SCL
t
t
tr
BUF
f
SDA
t
t HD;STA
Figure 19.
I2C-bus
SU;DAT
t
t
HD;DAT
t
VD;DAT
VD;ACK
timing diagram; rise and fall times refer to VIL and VIH
VDD
VDD
Open
RL = 500 Ω
VO
VI
PULSE
GENERATOR
D.U.T.
RT
CL
50 pF
DEFINITIONS
RL = Load resistor FOR LEDN. RL FOR SDA AND SCL > 1 kΩ
(3 mA or less current).
CL = Load capacitance includes jig and probe capacitance
RT = Termination resistance should be equal to the output
impedance ZO of the pulse generators.
Figure 20. Test circuitry for switching times
2004 Oct 01
14
SW02334
t
SU;STO
SW02333
Philips Semiconductors
Product data sheet
4-bit I2C LED dimmer
PCA9533
SO8: plastic small outline package; 8 leads; body width 3.9 mm
2004 Oct 01
15
SOT96-1
Philips Semiconductors
Product data sheet
4-bit I2C LED dimmer
PCA9533
TSSOP8: plastic thin shrink small outline package; 8 leads; body width 3 mm
2004 Oct 01
16
SOT505-1
Philips Semiconductors
Product data sheet
4-bit I2C LED dimmer
PCA9533
REVISION HISTORY
Rev
Date
Description
_2
20041001
Product data sheet (9397 750 13692). Supersedes data of 2003 Sep 19 (9397 750 12061).
Modifications:
• “Features” section on page 2:
– second bullet: change from “... between 0.625 and 160 Hz (1.6 seconds and 6.25 milliseconds)”
to “... between 0.591 Hz and 152 Hz (1.69 seconds and 6.58 milliseconds)”
– Last bullet: add “(MSOP8)”
• “Description” section on page 2:
– Third paragraph, third sentence: change from “... or blink at periods up to 1.6 second.” to “... or blink at
periods up to 1.69 second.”
– Fourth paragraph, first sentence: change from “... periods greater than 1.6 second ...” to “... periods greater
than 1.69 second.”
• “Input-Input register” table on page 4 modified; added note.
• Add section “Pins used as General Purpose I/Os” on page 5.
• Section “Power-on reset” on page 5 re-written.
• Figure 13 on page 8: add resistor values.
• (New) Note 1 added to DC Characteristics table on page 10, and its reference added at parameter VPOR.
• Figures 19 and 20 on page 13 modified.
_1
2004 Oct 01
20030919
Product data (9397 750 12061); ECN 853-2404 30307 dated 08 September 2003.
17
Philips Semiconductors
Product data sheet
4-bit I2C LED dimmer
PCA9533
Purchase of Philips I2C components conveys a license under the Philips’ I2C patent
to use the components in the I2C system provided the system conforms to the
I2C specifications defined by Philips. This specification can be ordered using the
code 9398 393 40011.
Data sheet status
Level
Data sheet status [1]
Product
status [2] [3]
Definitions
I
Objective data sheet
Development
This data sheet contains data from the objective specification for product development.
Philips Semiconductors reserves the right to change the specification in any manner without notice.
II
Preliminary data sheet
Qualification
This data sheet contains data from the preliminary specification. Supplementary data will be published
at a later date. Philips Semiconductors reserves the right to change the specification without notice, in
order to improve the design and supply the best possible product.
III
Product data sheet
Production
This data sheet contains data from the product specification. Philips Semiconductors reserves the
right to make changes at any time in order to improve the design, manufacturing and supply. Relevant
changes will be communicated via a Customer Product/Process Change Notification (CPCN).
[1] Please consult the most recently issued data sheet before initiating or completing a design.
[2] The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL
http://www.semiconductors.philips.com.
[3] For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status.
Definitions
Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see
the relevant data sheet or data handbook.
Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting
values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given
in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no
representation or warranty that such applications will be suitable for the specified use without further testing or modification.
Disclaimers
Life support — These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be
expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree
to fully indemnify Philips Semiconductors for any damages resulting from such application.
Right to make changes — Philips Semiconductors reserves the right to make changes in the products—including circuits, standard cells, and/or software—described
or contained herein in order to improve design and/or performance. When the product is in full production (status ‘Production’), relevant changes will be communicated
via a Customer Product/Process Change Notification (CPCN). Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys
no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent,
copyright, or mask work right infringement, unless otherwise specified.
 Koninklijke Philips Electronics N.V. 2004
All rights reserved. Printed in U.S.A.
Contact information
For additional information please visit
http://www.semiconductors.philips.com.
Fax: +31 40 27 24825
Date of release: 10-04
For sales offices addresses send e-mail to:
[email protected].
Document number:
2004 Oct 01
18
9397 750 13692