THS7360

THS7360
www.ti.com
SLOS674 – JUNE 2010
6-Channel Video Amplifier with 3-SD and 3-SD/ED/HD/Full-HD Filters and High Gain
Check for Samples: THS7360
FEATURES
DESCRIPTION
• Three SDTV Video Amplifiers for CVBS,
S-Video, Y’/P’B/P’R, 480i/576i, Y’U’V’, or G'B'R'
• Three SD/ED/HD/Full-HD Selectable Filters for
Y’/P’B/P’R, G’B’R’, or Computer RGB
• Bypassable Sixth-Order Low-Pass Filters:
– Fixed SD Channels: 9.5-MHz
– Selectable Filter (SF) Channels:
9.2-MHz/17-MHz/35-MHz/70-MHz
• Versatile Input Biasing:
– DC-Coupled with 120-mV Output Shift
– AC-Coupled with Sync-Tip Clamp or Bias
• Gain of 5.6 V/V (SD Channels) and
4.5 V/V (SF Channels)
• +2.7-V to +5-V Single-Supply Operation
• Rail-to-Rail Output:
– Output Swings Within 100 mV from the
Rails: Allows AC or DC Output Coupling
– Supports Driving Two Video Lines/Channel
• Low Total Quiescent Current: 24.5 mA at 3.3 V
• Disabled Supply Current Function: 0.1 mA
• Low Differential Gain/Phase: 0.15%/0.35°
• RoHS-Compliant TSSOP-20 Package
Fabricated using the revolutionary, complementary
Silicon-Germanium (SiGe) BiCom3X process, the
THS7360 is a low-power, single-supply, 2.7-V to 5-V,
six-channel integrated video buffer. It incorporates
three SDTV filter channels and three selectable filter
(SF) channels with SD/ED/HD/Full-HD (also known
as True-HD) HDTV filtering. All filters feature
sixth-order Butterworth characteristics that are useful
as digital-to-analog converter (DAC) reconstruction
filters or as analog-to-digital converter (ADC)
anti-aliasing filters.
1
2345
The THS7360 also has flexible input coupling
capabilities that can be configured for either ac- or
dc-coupled inputs. The 120-mV output level shift
allows for a full sync dynamic range at the output with
0-V input. The ac-coupled modes include a
transparent sync-tip clamp option for CVBS, Y', and
G'B'R' signals. AC-coupled biasing for C'/P'B/P'R
channels can easily be achieved by adding an
external resistor to VS+.
The THS7360 is an ideal choice for all video buffer
applications. Its rail-to-rail output stage with 5.6-V/V
gain (for SD channels) and 4.5-V/V gain (for SF
channels) allows for both ac and dc line driving. The
ability to drive two lines, or 75-Ω loads, allows for
maximum flexibility as a video line driver. The
24.5-mA total quiescent current at 3.3 V and 0.1 mA
(disabled mode) makes it a good choice for systems
that must meet power-sensitive Energy Star®
standards.
APPLICATIONS
•
•
•
Set Top Box Output Video Buffering
PVR/DVDR Output Buffering
BluRay™ Output Video Buffering
The THS7360 is available in a TSSOP-20 package
that is lead-free and green (RoHS-compliant).
THS7360
75 W
CVBS
R
S-Video
Y’
SOC/DAC/Encoder
R
S-Video
C’
R
1
SD1 IN
SD1 OUT 20
2
SD2 IN
SD2 OUT 19
3
SD3 IN
SD3 OUT 18
Filter 2
4
Filter 2
Disable SD 17
+2.7 V to
+5 V
5
VS+
Filter 1
6
Filter 1
Disable SF 15
7
SF1 IN
SF1 OUT 14
8
SF2 IN
SF2 OUT 13
9
SF3 IN
SF3 OUT 12
10
Bypass SD
CVBS Out
75 W
Y' Out
Disable SD
S-Video
GND 16
Disable SF
75 W
C' Out
75 W
Y'/G'
R
P'B/B'
P'B/B' Out
75 W
R
P'R/R' Out
Bypass
SD LPF
P'R/R'
Y'/G' Out
75 W
Bypass SF 11
Bypass
SF LPF
R
Figure 1. Single-Supply, DC-Input/DC-Output Coupled Video Line Driver
1
2
3
4
5
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
BluRay is a trademark of Blu-ray Disc Association (BDA).
Energy Star is a registered trademark of Energy Star.
Macrovision is a registered trademark of Macrovision Corporation.
All other trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2010, Texas Instruments Incorporated
THS7360
SLOS674 – JUNE 2010
www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
PACKAGE/ORDERING INFORMATION (1) (2)
PRODUCT
PACKAGE-LEAD
THS7360IPW
TSSOP-20
THS7360IPWR
(1)
(2)
ECO STATUS (2)
TRANSPORT MEDIA, QUANTITY
Rails, 70
Pb-Free, Green
Tape and Reel, 2000
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or visit the
device product folder at ti.com.
These packages conform to Lead (Pb)-free and green manufacturing specifications. Additional details including specific material content
can be accessed at www.ti.com/leadfree.
GREEN: TI defines Green to mean Lead (Pb)-Free and in addition, uses less package materials that do not contain halogens, including
bromine (Br), or antimony (Sb) above 0.1% of total product weight. N/A: Not yet available Lead (Pb)-Free; for estimated conversion
dates, go to www.ti.com/leadfree. Pb-FREE: TI defines Lead (Pb)-Free to mean RoHS compatible, including a lead concentration that
does not exceed 0.1% of total product weight, and, if designed to be soldered, suitable for use in specified lead-free soldering
processes.
ABSOLUTE MAXIMUM RATINGS (1)
Over operating free-air temperature range, unless otherwise noted.
Supply voltage, VS+ to GND
Input voltage, VI
Output current, IO
Continuous power dissipation
(2)
, TJ
–0.4 to VS+
V
±90
mA
°C
+125
°C
–60 to +150
°C
Human body model (HBM)
4000
V
Charge device model (CDM)
1000
V
Machine model (MM)
200
V
Storage temperature range, Tstg
(2)
(3)
V
+150
Maximum junction temperature, continuous operation, long-term reliability (3), TJ
(1)
UNIT
5.5
See the Thermal Information Table
Maximum junction temperature, any condition
ESD rating:
THS7360
Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may
degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond
those specified is not implied.
The absolute maximum junction temperature under any condition is limited by the constraints of the silicon process.
The absolute maximum junction temperature for continuous operation is limited by the package constraints. Operation above this
temperature may result in reduced reliability and/or lifetime of the device.
THERMAL INFORMATION
THS7360
THERMAL METRIC (1)
PW
UNITS
20 PINS
qJA
Junction-to-ambient thermal resistance
108.0
qJC(top)
Junction-to-case(top) thermal resistance
41.6
qJB
Junction-to-board thermal resistance
61.3
yJT
Junction-to-top characterization parameter
2.9
yJB
Junction-to-board characterization parameter
58.4
qJC(bottom)
Junction-to-case(bottom) thermal resistance
n/a
(1)
2
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS7360
THS7360
www.ti.com
SLOS674 – JUNE 2010
RECOMMENDED OPERATING CONDITIONS
MIN
NOM
MAX
UNIT
Supply voltage, VS+
2.7
5
V
Ambient temperature, TA
–40
+85
°C
ELECTRICAL CHARACTERISTICS: VS+ = +3.3 V
At TA = +25°C, RL = 150 Ω to GND, Filter mode, and dc-coupled input/output, unless otherwise noted.
THS7360
PARAMETER
MAX
UNITS
TEST
LEVEL (1)
8.2
10
MHz
B
9.5
11.3
MHz
B
TEST CONDITIONS
MIN
TYP
Passband bandwidth
–1 dB; VO = 0.2 VPP and 2 VPP
6.7
Small- and large-signal bandwidth
–3 dB; VO = 0.2 VPP and 2 VPP
8
AC PERFORMANCE (SD CHANNELS)
Bypass mode bandwidth
–3 dB; VO = 0.2 VPP
30
60
MHz
B
Bypass mode; VO = 2 VPP
60
150
V/ms
B
With respect to 500 kHz (2), f = 6.75 MHz
–0.8
0.4
dB
B
With respect to 500 kHz (2), f = 27 MHz
42
54
dB
B
f = 100 kHz
74
ns
C
f = 5.1 MHz with respect to 100 kHz
10.5
ns
C
0.3
ns
C
Slew rate
Attenuation
Group delay
Group delay variation
Channel-to-channel delay
1.3
Differential gain
NTSC/PAL
0.15/0.3
%
C
Differential phase
NTSC/PAL
0.35/0.5
Degrees
C
f = 1 MHz, VO = 1.4 VPP
–69
dB
C
100 kHz to 6 MHz, non-weighted
61
dB
C
100 kHz to 6 MHz, unified weighting
70
dB
C
Total harmonic distortion
Signal-to-noise ratio
Gain
All channels
f = 6.75 MHz, Filter mode
(2)
1.4
5.76
V/V
A
Ω
C
1.2
Ω
C
Disabled
28 || 3
kΩ || pF
C
f = 6.75 MHz, Filter mode
42
dB
C
f = 1 MHz, SD to SD channels, input referred
–58
dB
C
Return loss
(1)
5.60
f = 6.75 MHz, Bypass mode
Output impedance
Crosstalk
5.44
Test levels: (A) 100% tested at +25°C. Over temperature limits set by characterization and simulation. (B) Limits set by characterization
and simulation only. (C) Typical value only for information.
3.3-V supply filter specifications are ensured by 100% testing at 5-V supply along with design and characterization.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS7360
3
THS7360
SLOS674 – JUNE 2010
www.ti.com
ELECTRICAL CHARACTERISTICS: VS+ = +3.3 V (continued)
At TA = +25°C, RL = 150 Ω to GND, Filter mode, and dc-coupled input/output, unless otherwise noted.
THS7360
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
TEST
LEVEL (1)
6.6
8
9.6
MHz
B
AC PERFORMANCE (SF (3) CHANNELS, SD FILTER)
Passband bandwidth
–1 dB; VO = 0.2 VPP and 2 VPP
Small- and large-signal bandwidth
Attenuation
–3 dB; VO = 0.2 VPP and 2 VPP
7.8
9.2
11
MHz
B
With respect to 500 kHz (4), f = 6.75 MHz
–0.8
0.4
1.3
dB
B
With respect to 500 kHz (4), f = 27 MHz
42
50
dB
B
f = 100 kHz
62
ns
C
f = 5.1 MHz with respect to 100 kHz
10.5
ns
C
0.3
ns
C
Group delay
Group delay variation
Channel-to-channel delay
Total harmonic distortion
Signal-to-noise ratio
f = 1 MHz, VO = 1.4 VPP
–57
dB
C
100 kHz to 6.75 MHz, non-weighted
58
dB
C
100 kHz to 6.75 MHz, unified weighting
69
dB
C
V/V
A
Gain
All channels
Output impedance
f = 6.75 MHz
0.7
Ω
C
Return loss
f = 6.75 MHz
46
dB
C
f = 1 MHz, SF to SD channels, input referred
–57
dB
C
f = 1 MHz, SD to SF channels, input referred
–56
dB
C
f = 1 MHz, SF to SF channels, input referred
–56
dB
C
Crosstalk
4.37
4.50
4.63
AC PERFORMANCE (SF CHANNELS, ED FILTER)
Passband bandwidth
–1 dB; VO = 0.2 VPP and 2 VPP
11
15
18.5
MHz
B
Small- and large-signal bandwidth
–3 dB; VO = 0.2 VPP and 2 VPP
15
17
21
MHz
B
With respect to 500 kHz (4), f = 11 MHz
–1
0.1
1
dB
B
With respect to 500 kHz (4), f = 54 MHz
42
54
dB
B
f = 100 kHz
36
ns
C
f = 11 MHz with respect to 100 kHz
9
ns
C
0.3
ns
C
Attenuation
Group delay
Group delay variation
Channel-to-channel delay
Total harmonic distortion
Signal-to-noise ratio
f = 5 MHz, VO = 1.4 VPP
–50
dB
C
100 kHz to 12 MHz, non-weighted
57.5
dB
C
Unified weighting
68
dB
C
Gain
All channels
Output impedance
f = 12 MHz
Return loss
Crosstalk
(3)
(4)
4
4.37
4.5
V/V
A
0.7
4.63
Ω
C
f = 12 MHz
46
dB
C
f = 10 MHz, SF to SD channels, input referred
–46
dB
C
f = 10 MHz, SD to SF channels, input referred
–47
dB
C
f = 10 MHz, SF to SF channels, input referred
–36
dB
C
SF indicates selectable filter.
3.3-V supply filter specifications are ensured by 100% testing at 5-V supply along with design and characterization.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS7360
THS7360
www.ti.com
SLOS674 – JUNE 2010
ELECTRICAL CHARACTERISTICS: VS+ = +3.3 V (continued)
At TA = +25°C, RL = 150 Ω to GND, Filter mode, and dc-coupled input/output, unless otherwise noted.
THS7360
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
TEST
LEVEL (1)
26
30
36
MHz
B
AC PERFORMANCE (SF CHANNELS, HD FILTER)
Passband bandwidth
–1 dB; VO = 0.2 VPP and 2 VPP
Small- and large-signal bandwidth
Attenuation
–3 dB; VO = 0.2 VPP and 2 VPP
31
35
41
MHz
B
With respect to 500 kHz (5), f = 27 MHz
–0.8
0.4
1.3
dB
B
With respect to 500 kHz (5), f = 74 MHz
29
36
dB
B
f = 100 kHz
19
ns
C
f = 27 MHz with respect to 100 kHz
7
ns
C
0.3
ns
C
Group delay
Group delay variation
Channel-to-channel delay
Total harmonic distortion
Signal-to-noise ratio
f = 10 MHz, VO = 1.4 VPP
–52
dB
C
100 kHz to 30 MHz, non-weighted
54
dB
C
Unified weighting
65.5
dB
C
V/V
A
Gain
All channels
Output impedance
f = 30 MHz
1
Ω
C
Return loss
f = 30 MHz
43
dB
C
f = 25 MHz, SF to SD channels, input referred
–40
dB
C
f = 25 MHz, SD to SF channels, input referred
–60
dB
C
f = 25 MHz, SF to SF channels, input referred
–30
dB
C
Crosstalk
4.37
4.50
4.63
AC PERFORMANCE (SF CHANNELS, FULL-HD/TRUE-HD FILTER)
Passband bandwidth
–1 dB; VO = 0.2 VPP and 2 VPP
53
60
72
MHz
B
Small- and large-signal bandwidth
–3 dB; VO = 0.2 VPP and 2 VPP
64
70
83
MHz
B
With respect to 500 kHz (5), f = 54 MHz
–0.8
0.4
1.2
dB
B
With respect to 500 kHz (5), f = 148 MHz
30
37
dB
B
f = 100 kHz
11
ns
C
f = 54 MHz with respect to 100 kHz
4
ns
C
0.3
ns
C
Attenuation
Group delay
Group delay variation
Channel-to-channel delay
Total harmonic distortion
Signal-to-noise ratio
f = 20 MHz, VO = 1.4 VPP
–55
dB
C
100 kHz to 60 MHz, non-weighted
53
dB
C
Unified weighting
64
dB
C
Gain
All channels
Output impedance
f = 60 MHz
Return loss
Crosstalk
(5)
4.37
4.50
V/V
A
1.5
4.63
Ω
C
f = 60 MHz
40
dB
C
f = 50 MHz, SF to SD channels, input referred
–30
dB
C
f = 50 MHz, SD to SF channels, input referred
–50
dB
C
f = 50 MHz, SF to SF channels, input referred
–30
dB
C
3.3-V supply filter specifications are ensured by 100% testing at 5-V supply along with design and characterization.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS7360
5
THS7360
SLOS674 – JUNE 2010
www.ti.com
ELECTRICAL CHARACTERISTICS: VS+ = +3.3 V (continued)
At TA = +25°C, RL = 150 Ω to GND, Filter mode, and dc-coupled input/output, unless otherwise noted.
THS7360
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
TEST
LEVEL (1)
AC PERFORMANCE (SF CHANNELS, BYPASS)
Passband bandwidth
–1 dB; VO = 0.2 VPP
140
180
MHz
B
Small-signal bandwidth
B
–3 dB; VO = 0.2 VPP
200
280
MHz
Slew rate
VO = 2 VPP
650
800
V/µs
B
Group delay
f = 100 kHz
3
ns
C
0.3
ns
C
f = 20 MHz, VO = 1.4 VPP
–72
dB
C
100 kHz to 100 MHz, non-weighted
56
dB
C
dB
C
Channel-to-channel delay
Total harmonic distortion
Signal-to-noise ratio
Unified weighting
Gain
All channels
Output impedance
Return loss
Crosstalk
66
4.37
4.5
4.63
V/V
B
f = 100 MHz
3
Ω
C
Disabled
12 || 3
kΩ || pF
C
f = 100 MHz
34
dB
C
f = 50 MHz, SF to SD channels, input referred
–30
dB
C
f = 50 MHz, SD to SF channels, input referred
–48
dB
C
f = 50 MHz, SF to SF channels, input referred
–30
dB
C
A
DC PERFORMANCE
Biased output voltage
Input voltage range
VIN = 0 V, SD channels
35
VIN = 0 V, SF channels
35
DC input, limited by output
Sync-tip clamp charge current
150
315
mV
120
300
mV
A
–0.1/0.65
V
C
VIN = –0.1 V, SD channels
140
200
mA
A
VIN = –0.1 V, SF channels
280
400
mA
A
800 || 2
kΩ || pF
C
3.15
V
C
Input impedance
OUTPUT CHARACTERISTICS
RL = 150 Ω to +1.65 V
RL = 150 Ω to GND
3.1
V
A
RL = 75 Ω to +1.65 V
3.1
V
C
RL = 75 Ω to GND
3
V
C
RL = 150 Ω to +1.65 V (VIN = –0.2 V)
0.06
V
C
RL = 150 Ω to GND (VIN = –0.2 V)
0.05
RL = 75 Ω to +1.65 V (VIN = –0.2 V)
High output voltage swing
2.85
V
A
0.1
V
C
RL = 75 Ω to GND (VIN = –0.2 V)
0.05
V
C
Output current (sourcing)
RL = 10 Ω to +1.65 V
80
mA
C
Output current (sinking)
RL = 10 Ω to +1.65 V
70
mA
C
Low output voltage swing
6
Submit Documentation Feedback
0.12
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS7360
THS7360
www.ti.com
SLOS674 – JUNE 2010
ELECTRICAL CHARACTERISTICS: VS+ = +3.3 V (continued)
At TA = +25°C, RL = 150 Ω to GND, Filter mode, and dc-coupled input/output, unless otherwise noted.
THS7360
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
TEST
LEVEL (1)
2.6
3.3
5.5
V
B
POWER SUPPLY
Operating voltage
Total quiescent current, no load
VIN = 0 V, all channels on
18.8
24.5
29.5
mA
A
VIN = 0 V, SD channels on, SF channels off
5.6
7.1
9
mA
A
VIN = 0 V, SD channels off, SF channels on
13.2
17.4
20.5
mA
A
VIN = 0 V, all channels off, VDISABLE = 3 V
0.1
10
mA
A
At dc
56
dB
C
V
A
Power-supply rejection ratio
(PSRR)
LOGIC CHARACTERISTICS
VIH
Disabled or Bypass engaged
VIL
Enabled or Bypass disengaged
1.6
0.75
1.4
IIH
Applied voltage = 3.3 V
IIL
Applied voltage = 0 V
0.6
V
A
1
mA
C
1
mA
C
Disable time
150
ns
C
Enable time
150
ns
C
Bypass/filter switch time
15
ns
C
Table 1. TRUTH TABLE: VS+ = +3.3 V (1)
(1)
FILTER 1
FILTER 2
BYPASS SF
0
0
0
Selects the standard definition filter (9.2 MHz) for the SF channels
DESCRIPTION
0
1
0
Selects the enhanced definition filter (17 MHz) for the SF channels
1
0
0
Selects the high-definition filter (35 MHz) for the SF channels
1
1
0
Selects the full/true high-definition filter (70 MHz) for the SF channels
X
X
1
Bypasses the filters for the SF channels
The logic input pins default to a logic '0' condition when left floating.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS7360
7
THS7360
SLOS674 – JUNE 2010
www.ti.com
ELECTRICAL CHARACTERISTICS: VS+ = +5 V
At TA = +25°C, RL = 150 Ω to GND, Filter mode, and dc-coupled input/output, unless otherwise noted.
THS7360
TEST CONDITIONS
MIN
TYP
MAX
UNITS
TEST
LEVEL (1)
Passband bandwidth
–1 dB; VO = 0.2 VPP and 2 VPP
6.7
8.2
10
MHz
B
Small- and large-signal bandwidth
–3 dB; VO = 0.2 VPP and 2 VPP
8
9.5
11.3
MHz
B
–3 dB; VO = 0.2 VPP
30
60
MHz
B
Bypass mode; VO = 2 VPP
60
150
V/ms
B
With respect to 500 kHz, f = 6.75 MHz
–0.8
0.4
dB
A
With respect to 500 kHz, f = 27 MHz
42
54
dB
A
f = 100 kHz
74
ns
C
f = 5.1 MHz with respect to 100 kHz
10.5
ns
C
0.3
ns
C
PARAMETER
AC PERFORMANCE (SD CHANNELS)
Bypass mode bandwidth
Slew rate
Attenuation
Group delay
Group delay variation
Channel-to-channel delay
1.3
Differential gain
NTSC/PAL
0.15/0.3
%
C
Differential phase
NTSC/PAL
0.35/0.5
Degrees
C
Total harmonic distortion
Signal-to-noise ratio
Gain
f = 1 MHz, VO = 1.4 VPP
–73
dB
C
100 kHz to 6 MHz, non-weighted
61
dB
C
100 kHz to 6 MHz, unified weighting
70
dB
C
All channels
Output impedance
5.44
5.60
A
0.7
5.76
Ω
C
f = 6.75 MHz, Bypass mode
0.6
Ω
C
Disabled
28 || 3
kΩ || pF
C
f = 6.75 MHz, Filter mode
46
dB
C
f = 1 MHz, SD to SD channels, input referred
–58
dB
C
Return loss
Crosstalk
V/V
f = 6.75 MHz, Filter mode
AC PERFORMANCE (SF (2) CHANNELS, SD FILTER)
Passband bandwidth
–1 dB; VO = 0.2 VPP and 2 VPP
6.6
8
9.6
MHz
B
Small- and large-signal bandwidth
–3 dB; VO = 0.2 VPP and 2 VPP
7.8
9.2
11
MHz
B
With respect to 500 kHz, f = 6.75 MHz
–0.8
0.4
1.3
dB
A
With respect to 500 kHz, f = 27 MHz
42
Attenuation
50
dB
A
f = 100 kHz
62
ns
C
f = 5.1 MHz with respect to 100 kHz
10.5
ns
C
0.3
ns
C
f = 1 MHz, VO = 1.4 VPP
–59
dB
C
100 kHz to 6.75 MHz, non-weighted
58
dB
C
100 kHz to 6.75 MHz, unified weighting
69
dB
C
Group delay
Group delay variation
Channel-to-channel delay
Total harmonic distortion
Signal-to-noise ratio
Gain
All channels
V/V
A
Output impedance
f = 6.75 MHz
0.7
Ω
C
Return loss
f = 6.75MHz
46
dB
C
f = 1 MHz, SF to SD channels, input referred
–57
dB
C
f = 1 MHz, SD to SF channels, input referred
–56
dB
C
f = 1 MHz, SF to SF channels, input referred
–56
dB
C
Crosstalk
(1)
(2)
8
4.37
4.50
4.63
Test levels: (A) 100% tested at +25°C. Over temperature limits set by characterization and simulation. (B) Limits set by characterization
and simulation only. (C) Typical value only for information.
SF indicates selectable filter.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS7360
THS7360
www.ti.com
SLOS674 – JUNE 2010
ELECTRICAL CHARACTERISTICS: VS+ = +5 V (continued)
At TA = +25°C, RL = 150 Ω to GND, Filter mode, and dc-coupled input/output, unless otherwise noted.
THS7360
PARAMETER
MIN
TYP
MAX
UNITS
TEST
LEVEL (1)
–1 dB; VO = 0.2 VPP and 2 VPP
11
15
18.5
MHz
B
TEST CONDITIONS
AC PERFORMANCE (SF CHANNELS, ED FILTER)
Passband bandwidth
Small- and large-signal bandwidth
Attenuation
–3 dB; VO = 0.2 VPP and 2 VPP
15
17
21
MHz
B
With respect to 500 kHz, f = 11 MHz
–1
0
1
dB
A
With respect to 500 kHz, f = 54 MHz
42
54
dB
A
f = 100 kHz
36
ns
C
f = 11 MHz with respect to 100 kHz
9
ns
C
0.3
ns
C
Group delay
Group delay variation
Channel-to-channel delay
Total harmonic distortion
Signal-to-noise ratio
f = 5 MHz, VO = 1.4 VPP
–53
dB
C
100 kHz to 12 MHz, non-weighted
57.5
dB
C
Unified weighting
68
dB
C
V/V
A
Gain
All channels
Output impedance
f = 12 MHz
0.7
Ω
C
Return loss
f = 12 MHz
46
dB
C
f = 10 MHz, SF to SD channels, input referred
–46
dB
C
f = 10 MHz, SD to SF channels, input referred
–47
dB
C
f = 10 MHz, SF to SF channels, input referred
–36
dB
C
Crosstalk
4.37
4.50
4.63
AC PERFORMANCE (SF CHANNELS, HD FILTER)
Passband bandwidth
–1 dB; VO = 0.2 VPP and 2 VPP
26
31
36
MHz
B
Small- and large-signal bandwidth
–3 dB; VO = 0.2 VPP and 2 VPP
31
35
41
MHz
B
With respect to 500 kHz (3), f = 27 MHz
–0.8
0.4
1.3
dB
A
With respect to 500 kHz (3), f = 74 MHz
29
36
dB
A
f = 100 kHz
19
ns
C
f = 27MHz with respect to 100 kHz
7
ns
C
0.3
ns
C
Attenuation
Group delay
Group delay variation
Channel-to-channel delay
Total harmonic distortion
Signal-to-noise ratio
f = 10 MHz, VO = 1.4 VPP
–53
dB
C
100 kHz to 30 MHz, non-weighted
54
dB
C
Unified weighting
65.5
dB
C
Gain
All channels
Output impedance
f = 30 MHz
Return loss
Crosstalk
(3)
4.37
4.50
V/V
A
1
4.63
Ω
C
f = 30 MHz
43
dB
C
f = 25 MHz, SF to SD channels, input referred
–40
dB
C
f = 25 MHz, SD to SF channels, input referred
–60
dB
C
f = 25 MHz, SF to SF channels, input referred
–30
dB
C
3.3-V supply filter specifications are ensured by 100% testing at 5-V supply along with design and characterization.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS7360
9
THS7360
SLOS674 – JUNE 2010
www.ti.com
ELECTRICAL CHARACTERISTICS: VS+ = +5 V (continued)
At TA = +25°C, RL = 150 Ω to GND, Filter mode, and dc-coupled input/output, unless otherwise noted.
THS7360
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
TEST
LEVEL (1)
53
61
72
MHz
B
AC PERFORMANCE (SF CHANNELS, FULL/TRUE-HD FILTER)
Passband bandwidth
–1 dB; VO = 0.2 VPP and 2 VPP
Small- and large-signal bandwidth
Attenuation
–3 dB; VO = 0.2 VPP and 2 VPP
64
70
83
MHz
B
With respect to 500 kHz (4), f = 54 MHz
–0.8
0.4
1.2
dB
A
With respect to 500 kHz (4), f = 148 MHz
30
36
dB
A
f = 100 kHz
11
ns
C
f = 54 MHz with respect to 100 kHz
4
ns
C
0.3
ns
C
Group delay
Group delay variation
Channel-to-channel delay
Total harmonic distortion
Signal-to-noise ratio
f = 20 MHz, VO = 1.4 VPP
–54
dB
C
100 kHz to 60 MHz, non-weighted
53
dB
C
Unified weighting
64
dB
C
V/V
A
Gain
All channels
Output impedance
f = 60 MHz
1.5
Ω
C
Return loss
f = 60 MHz
40
dB
C
f = 50 MHz, SF to SD channels, input referred
–30
dB
C
f = 50 MHz, SD to SF channels, input referred
–50
dB
C
f = 50 MHz, SF to SF channels, input referred
–30
dB
C
Crosstalk
4.37
4.50
4.63
AC PERFORMANCE (SF CHANNELS, BYPASS)
Passband bandwidth
–1 dB; VO = 0.2 VPP
140
180
MHz
B
Small-signal bandwidth
–3 dB; VO = 0.2 VPP
200
290
MHz
B
Slew rate
VO = 2 VPP
650
850
V/µs
B
Group delay
f = 100 kHz
3
ns
C
0.3
ns
C
f = 20 MHz, VO = 1.4 VPP
–72
dB
C
100 kHz to 100 MHz, non-weighted
56
dB
C
dB
C
Channel-to-channel delay
Total harmonic distortion
Signal-to-noise ratio
Unified weighting
Gain
All channels
Output impedance
(4)
10
4.50
4.63
V/V
B
f = 100 MHz
3
Ω
C
Disabled
12 || 3
kΩ || pF
C
f = 100 MHz
34
dB
C
f = 50 MHz, SF to SD channels, input referred
–30
dB
C
f = 50 MHz, SD to SF channels, input referred
–48
dB
C
f = 50 MHz, SF to SF channels, input referred
–30
dB
C
Return loss
Crosstalk
66
4.37
3.3-V supply filter specifications are ensured by 100% testing at 5-V supply along with design and characterization.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS7360
THS7360
www.ti.com
SLOS674 – JUNE 2010
ELECTRICAL CHARACTERISTICS: VS+ = +5 V (continued)
At TA = +25°C, RL = 150 Ω to GND, Filter mode, and dc-coupled input/output, unless otherwise noted.
THS7360
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
TEST
LEVEL (1)
VIN = 0 V, SD channels
35
160
315
mV
A
VIN = 0 V, SF channels
35
120
300
DC PERFORMANCE
Biased output voltage
Input voltage range
DC input, limited by output range
Sync-tip clamp charge current
VIN = –0.1 V, SD channels
140
VIN = –0.1 V, SF channels
280
mV
A
–0.1/1
V
C
200
mA
A
400
mA
A
800 || 2
kΩ || pF
C
4.85
V
C
4.75
V
A
RL = 75 Ω to +2.5V
4.7
V
C
RL = 75 Ω to GND
4.5
V
C
RL = 150 Ω to +2.5 V (VIN = –0.2 V)
0.06
V
C
RL = 150 Ω to GND (VIN = –0.2 V)
0.05
RL = 75 Ω to +2.5 V (VIN = –0.2 V)
0.1
Input impedance
OUTPUT CHARACTERISTICS
RL = 150 Ω to +2.5 V
RL = 150 Ω to GND
High output voltage swing
Low output voltage swing
4.4
0.12
V
A
V
C
RL = 75 Ω to GND (VIN = –0.2 V)
0.05
V
C
Output current (sourcing)
RL = 10 Ω to +2.5 V
90
mA
C
Output current (sinking)
RL = 10 Ω to +2.5 V
85
mA
C
POWER SUPPLY
Operating voltage
Total quiescent current, no load
2.6
5
5.5
V
B
VIN = 0 V, all channels on
19.7
25.5
31.2
mA
A
VIN = 0 V, SD channels on, SF channels off
6
7.5
9.5
mA
A
VIN = 0 V, SD channels off, SF channels on
13.7
18
21.7
mA
A
VIN = 0 V, all channels off, VDISABLE = 3 V
0.5
10
mA
A
At dc
56
dB
C
V
A
V
A
Power-supply rejection ratio
(PSRR)
LOGIC CHARACTERISTICS (5)
VIH
Disabled or Bypass engaged
VIL
Enabled or Bypass disengaged
1.2
IIH
Applied voltage = 3.3 V
1
mA
C
IIL
Applied voltage = 0 V
1
mA
C
Disable time
100
ns
C
Enable time
100
ns
C
Bypass/filter switch time
10
ns
C
(5)
2.1
1.9
1
The logic input pins default to a logic '0' condition when left floating.
Table 2. TRUTH TABLE: VS+ = +5 V (1)
(1)
FILTER 1
FILTER 2
BYPASS SF
0
0
0
Selects the standard definition filter (9.2 MHz) for the SF channels
DESCRIPTION
0
1
0
Selects the enhanced definition filter (17 MHz) for the SF channels
1
0
0
Selects the high-definition filter (35 MHz) for the SF channels
1
1
0
Selects the full/true high-definition filter (70 MHz) for the SF channels
X
X
1
Bypasses the filters for the SF channels
The logic input pins default to a logic '0' condition when left floating.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS7360
11
THS7360
SLOS674 – JUNE 2010
www.ti.com
PIN CONFIGURATION
PW PACKAGE
TSSOP-20
(TOP VIEW)
SD1 IN
1
20
SD1 OUT
SD2 IN
2
19
SD2 OUT
SD3 IN
3
18
SD3 OUT
Filter 2
4
17
Disable SD
VS+
5
16
GND
Filter 1
6
15
Disable SF
SF1 IN
7
14
SF1 OUT
SF2 IN
8
13
SF2 OUT
SF3 IN
9
12
SF3 OUT
Bypass SD
10
11
Bypass SF
TERMINAL FUNCTIONS
TERMINAL
NAME
NO.
I/O
SD1 IN
1
I
Standard-definition video input, channel 1; LPF = 9.5 MHz
DESCRIPTION
SD2 IN
2
I
Standard-definition video input, channel 2; LPF = 9.5 MHz
SD3 IN
3
I
Standard-definition video input, channel 3; LPF = 9.5 MHz
Filter 2
4
I
Used in conjunction with Filter 1 for selecting the LPF on SF channels
VS+
5
I
Positive power-supply pin; connect to +2.7 V up to +5 V
Filter 1
6
I
Used in conjunction with Filter 2 for selecting the LPF on SF channels
SF1 IN
7
I
Component or RGB video input, channel 1
SF2 IN
8
I
Component or RGB video input, channel 2
SF3 IN
9
I
Component or RGB video input, channel 3
Bypass SD
10
I
Bypass all SD channel filters. Logic high bypasses the internal filters and logic low engages the
internal filters.
Bypass SF
11
I
Bypass all SF channel filters. Logic high bypasses the internal filters and logic low engages the
internal filters.
SF3 OUT
12
O
Component or RGB video output, channel 3
SF2 OUT
13
O
Component or RGB video output, channel 2
SF1 OUT
14
O
Component or RGB video output, channel 1
Disable SF
15
I
Disable selectable filter channels. Logic high disables the SF channels and logic low enables the SF
channels.
GND
16
I
Ground pin for all internal circuitry
Disable SD
17
I
Disable standard definition channels. Logic high disables the SD channels and logic low enables the
SD channels.
SD3 OUT
18
O
Standard-definition video output, channel 3; LPF = 9.5 MHz
SD2 OUT
19
O
Standard-definition video output, channel 2; LPF = 9.5 MHz
SD1 OUT
20
O
Standard-definition video output, channel 1; LPF = 9.5 MHz
12
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS7360
THS7360
www.ti.com
SLOS674 – JUNE 2010
FUNCTIONAL BLOCK DIAGRAM
+VS
gm
Level
Shift
SD Channel 1
Input
(CVBS)
LPF
Sync-Tip Clamp
(DC Restore)
800 kW
Bypass SD
5.6
V/V
SD Channel 1
Output
(CVBS)
5.6
V/V
SD Channel 2
Output
(S-Video Y)
5.6
V/V
SD Channel 3
Output
(S-Video C)
6-Pole
9.5 MHz
+VS
gm
Level
Shift
SD Channel 2
Input
(S-Video Y)
LPF
Sync-Tip Clamp
(DC Restore)
800 kW
Bypass SD
6-Pole
9.5 MHz
+VS
gm
Level
Shift
SD Channel 3
Input
(S-Video C)
LPF
Sync-Tip Clamp
(DC Restore)
800 kW
Bypass SD
6-Pole
9.5 MHz
Bypass SD
Disable SD
+VS
Bypass SF
Disable SF
gm
Level
Shift
SD/ED/HD/Full-HD
Channel 1 Input
(Y’/G)
LPF
Sync-Tip Clamp
(DC Restore)
800 kW
Bypass SF
4.5
V/V
SD/ED/HD/Full-HD
Channel 1 Output
(Y’/G)
4.5
V/V
SD/ED/HD/Full-HD
Channel 2 Output
(P’B/B)
4.5
V/V
SD/ED/HD/Full-HD
Channel 3 Output
(P’R/R)
6-Pole
9.2/17/35/70 MHz
+VS
gm
Level
Shift
SD/ED/HD/Full-HD
Channel 2 Input
(P’B/B)
LPF
Sync-Tip Clamp
(DC Restore)
800 kW
Bypass SF
6-Pole
9.2/17/35/70 MHz
+VS
gm
Level
Shift
SD/ED/HD/Full-HD
Channel 3 Input
(P’R/R)
800 kW
Sync-Tip Clamp
(DC Restore)
+2.7 V to +5 V
Bypass SF
LPF
6-Pole
9.2/17/35/70 MHz
Filter Selection
NOTE: SF indicates selectable filter.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS7360
13
THS7360
SLOS674 – JUNE 2010
www.ti.com
TYPICAL CHARACTERISTICS
Table 3. Table of Graphs: 3.3 V, Standard-Definition (SD) Channels
TITLE
FIGURE
SD Channels Small-Signal Gain vs Frequency Response
Figure 2, Figure 3, Figure 8, Figure 9
SD Channels Phase vs Frequency Response
Figure 4
SD Channels Group Delay vs Frequency Response
Figure 5
SD Channels Large-Signal Gain vs Frequency Response
Figure 6, Figure 7
SD Channels 1.4 VPP THD vs Frequency
Figure 10
SD Channels 0.5 VPP THD vs Frequency
Figure 11
SD Channels Differential Gain
Figure 12
SD Channels Differential Phase
Figure 13
Table 4. Table of Graphs: 3.3 V, Selectable Filter (SF) Channels
TITLE
FIGURE
SF Channels Small-Signal Gain vs Frequency Response
Figure 14, Figure 15
SF Channels Phase vs Frequency Response
Figure 16
SF Channels Group Delay vs Frequency Response
Figure 17, Figure 18
SF Channels AC-Coupled Small-Signal Gain vs Frequency Response
Figure 19, Figure 20
SF Channels Large-Signal Gain vs Frequency Response
Figure 21, Figure 22
SF Channels 1.4 VPP THD vs Frequency
Figure 23
SF Channels 0.5 VPP THD vs Frequency
Figure 24
Table 5. Table of Graphs: 5 V, Standard-Definition (SD) Channels
TITLE
FIGURE
SD Channels Small-Signal Gain vs Frequency Response
Figure 25, Figure 26, Figure 31, Figure 32
SD Channels Phase vs Frequency Response
Figure 27
SD Channels Group Delay vs Frequency Response
Figure 28
SD Channels Large-Signal Gain vs Frequency Response
Figure 29, Figure 30
SD Channels 1.4 VPP THD vs Frequency
Figure 33
SD Channels 0.5 VPP THD vs Frequency
Figure 34
SD Channels Differential Gain
Figure 35
SD Channels Differential Phase
Figure 36
Table 6. Table of Graphs: 5 V, Selectable Filter (SF) Channels
14
TITLE
FIGURE
SF Channels Small-Signal Gain vs Frequency Response
Figure 37, Figure 38
SF Channels Phase vs Frequency Response
Figure 39
SF Channels Group Delay vs Frequency Response
Figure 40, Figure 41
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS7360
THS7360
www.ti.com
SLOS674 – JUNE 2010
TYPICAL CHARACTERISTICS: 3.3 V, Standard-Definition (SD) Channels
With load = 150 Ω || 5 pF, dc-coupled input and output, unless otherwise noted.
SD CHANNELS SMALL-SIGNAL GAIN vs FREQUENCY
RESPONSE
SD CHANNELS SMALL-SIGNAL GAIN vs FREQUENCY
RESPONSE
20
15.5
15.0
0
-10
VS+ = 3.3 V
Load = RL || 10 pF
DC-Coupled Output
VO = 200 mVPP
Small-Signal Gain (dB)
Small-Signal Gain (dB)
10
-20
RL = 150 W, Filter Mode
RL = 75 W, Filter Mode
RL = 150 W, Bypass Mode
RL = 75 W, Bypass Mode
-30
-40
-50
100 k
1M
14.5
14.0
VS+ = 3.3 V
Load = RL || 10 pF
DC-Coupled Output
VO = 200 mVPP
13.5
13.0
RL = 150 W, Filter Mode
RL = 75 W, Filter Mode
RL = 150 W, Bypass Mode
RL = 75 W, Bypass Mode
12.5
12.0
10 M
100 M
11.5
100 k
1G
1M
Figure 2.
Figure 3.
SD CHANNELS PHASE vs FREQUENCY RESPONSE
SD CHANNELS GROUP DELAY vs FREQUENCY
RESPONSE
120
45
RL = 75 W and 150 W
Bypass Mode
0
110
Group Delay (ns)
-45
Phase (°)
-90
-135
RL = 75 W and 150 W
Filter Mode
-180
-225
-270
-315
VS+ = 3.3 V
Load = RL || 10 pF
DC-Coupled Output
VO = 200 mVPP
-360
100 k
100
VS+ = 3.3 V
Load = RL || 10 pF
DC-Coupled Output
VO = 200 mVPP
90
80
RL = 75 W and 150 W
Filter Mode
70
60
1M
100 M
10 M
50
100 k
1G
1M
100 M
10 M
Frequency (Hz)
Frequency (Hz)
Figure 4.
Figure 5.
SD CHANNELS LARGE-SIGNAL GAIN vs FREQUENCY
RESPONSE
SD CHANNELS LARGE-SIGNAL GAIN vs FREQUENCY
RESPONSE
20
15.5
Bypass Mode
Bypass Mode
15.0
10
Filter Mode
Large-Signal Gain (dB)
Large-Signal Gain (dB)
100 M
10 M
Frequency (Hz)
Frequency (Hz)
0
VO = 0.2 VPP
-10
VO = 1 VPP
-20
VO = 2 VPP
-30
-40
VO = 0.2 VPP
VS+ = 3.3 V
Load = 150 W || 10 pF
DC-Coupled Output
-50
100 k
1M
14.0
13.5
10 M
100 M
1G
VO = 0.2 VPP and 2 VPP
13.0
12.5
12.0
VO = 2 VPP
VO = 0.2 VPP
Filter Mode
14.5
VS+ = 3.3 V
Load = 150 W || 10 pF
DC-Coupled Output
11.5
100 k
VO = 2 VPP
VO = 1 VPP
1M
10 M
100 M
Frequency (Hz)
Frequency (Hz)
Figure 6.
Figure 7.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS7360
15
THS7360
SLOS674 – JUNE 2010
www.ti.com
TYPICAL CHARACTERISTICS: 3.3 V, Standard-Definition (SD) Channels (continued)
With load = 150 Ω || 5 pF, dc-coupled input and output, unless otherwise noted.
SD CHANNELS SMALL-SIGNAL GAIN vs FREQUENCY
RESPONSE
20
SD CHANNELS SMALL-SIGNAL GAIN vs FREQUENCY
RESPONSE
15.5
Bypass Mode
Bypass Mode
15.0
Filter Mode
0
AC
-10
DC
-20
VS+ = 3.3 V
Load = 150 W || 10 pF
AC- vs DC-Coupled Output
VO = 0.2 VPP
-30
-40
-50
100 k
1M
DC
Small-Signal Gain (dB)
Small-Signal Gain (dB)
10
VS+ = 3.3 V
Load = 150 W || 10 pF
AC- vs DC-Coupled Output
VO = 0.2 VPP
14.5
14.0
13.5
DC
13.0
AC or DC
Filter Mode
12.5
12.0
AC
10 M
11.5
100 k
1G
100 M
1M
Figure 8.
Figure 9.
SD CHANNELS 0.5-VPP THD vs FREQUENCY
-45
-40
-50
-45
SD Filter
-55
-60
-65
VS+ = 3.3 V
RL = 150 W || 5 pF
DC-Coupled Output
VO = 1.4 VPP
Bypass SD
-75
-80
-85
1M
Total Harmonic Distortion (dBc)
Total Harmonic Distortion (dBc)
SD CHANNELS 1.4-VPP THD vs FREQUENCY
-35
-70
-60
SD Filter
-65
-70
-75
-80
1M
Frequency (Hz)
Figure 10.
Figure 11.
SD CHANNELS DIFFERENTIAL PHASE
0.50
0.45
VS+ = 3.3 V
Filter Mode
0.40
NTSC
Differential Phase (°)
Differential Gain (%)
-0.05
-0.10
-0.15
PAL
-0.20
0.35
0.30
PAL
0.25
0.20
NTSC
0.15
0.10
VS+ = 3.3 V
Filter Mode
1st
0.05
0
2nd
3rd
4th
5th
6th
Figure 12.
16
100 M
10 M
Frequency (Hz)
SD CHANNELS DIFFERENTIAL GAIN
-0.30
VS+ = 3.3 V
RL = 150 W || 5 pF
DC-Coupled Output
VO = 0.5 VPP
Bypass SD
-85
-95
100 M
10 M
-55
-90
0
-0.25
100 M
10 M
Frequency (Hz)
Frequency (Hz)
-50
AC
1st
2nd
3rd
4th
5th
6th
Figure 13.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS7360
THS7360
www.ti.com
SLOS674 – JUNE 2010
TYPICAL CHARACTERISTICS: 3.3 V, Selectable Filter (SF) Channels
With load = 150 Ω || 5 pF, dc-coupled input and output, unless otherwise noted.
SF CHANNELS SMALL-SIGNAL GAIN vs FREQUENCY
RESPONSE
SF CHANNELS SMALL-SIGNAL GAIN vs FREQUENCY
RESPONSE
20
13.5
Bypass
13.0
SD Filter
Small-Signal Gain (dB)
Small-Signal Gain (dB)
10
0
ED Filter
Full-HD
Filter
-10
HD Filter
-20
VS+ = 3.3 V
Load = 150 W || 5 pF
DC-Coupled Output
VO = 200 mVPP
-30
-40
12.5
SD Filter
12.0
ED Filter
11.0
10.5
10.0
-50
9.5
1M
10 M
HD Filter
10 M
Figure 14.
Figure 15.
SF CHANNELS PHASE vs FREQUENCY RESPONSE
SF CHANNELS GROUP DELAY vs FREQUENCY
RESPONSE
100
0
90
Full-HD Filter
-45
Group Delay (ns)
80
-90
HD Filter
-135
ED Filter
-180
SD Filter
-225
VS+ = 3.3 V
Load = 150 W || 5 pF
DC-Coupled Output
VO = 200 mVPP
-270
-315
-360
100 k
1M
VS+ = 3.3 V
Load = 150 W || 5 pF
DC-Coupled Output
VO = 200 mVPP
70
60
SD Filter
50
40
30
10 M
20
100 k
1G
100 M
ED Filter
1M
100 M
Figure 16.
Figure 17.
SF CHANNELS GROUP DELAY vs FREQUENCY
RESPONSE
SF CHANNELS AC-COUPLED SMALL-SIGNAL GAIN vs
FREQUENCY RESPONSE
20
VS+ = 3.3 V
Load = 150 W || 5 pF
DC-Coupled Output
VO = 200 mVPP
10
Small-Signal Gain (dB)
Group Delay (ns)
10 M
Frequency (Hz)
Frequency (Hz)
30
1G
100 M
Frequency (Hz)
Bypass
35
Bypass
Frequency (Hz)
45
Phase (°)
VS+ = 3.3 V
Load =
150 W || 5 pF
DC-Coupled
Output
VO = 200 mVPP
1M
1G
100 M
Full-HD
Filter
11.5
25
20
HD Filter
15
Full-HD Filter
10
-10
-20
-30
-40
5
-50
1M
10 M
100 M
SD Filter
ED Filter
HD Filter
Full-HD Filter
Bypass
0
VS+ = 3.3 V
Load = 150 W || 5 pF
AC-Coupled Output
VO = 200 mVPP
1M
Frequency (Hz)
10 M
100 M
1G
Frequency (Hz)
Figure 18.
Figure 19.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS7360
17
THS7360
SLOS674 – JUNE 2010
www.ti.com
TYPICAL CHARACTERISTICS: 3.3 V, Selectable Filter (SF) Channels (continued)
With load = 150 Ω || 5 pF, dc-coupled input and output, unless otherwise noted.
SF CHANNELS AC-COUPLED SMALL-SIGNAL GAIN vs
FREQUENCY RESPONSE
SF CHANNELS LARGE-SIGNAL GAIN vs FREQUENCY
RESPONSE
14.5
20
Small-Signal Gain (dB)
13.5
Full-HD Filter
Bypass
10
Large-Signal Gain (dB)
SD Filter
ED Filter
HD Filter
14.0
13.0
12.5
12.0
11.5
11.0
10.5
10.0
VS+ = 3.3 V
Load =
150 W || 5 pF
AC-Coupled
Output
VO = 200 mVPP
SD Filter
ED Filter
HD Filter
Full-HD Filter
Bypass 2 VPP
Bypass 1 VPP
0
-10
-20
-30
VS+ = 3.3 V, VO = 2 VPP
Load = 150 W || 5 pF
DC-Coupled Output
-40
-50
9.5
1M
10 M
1M
1G
100 M
Figure 20.
Figure 21.
SF CHANNELS 1.4-VPP THD vs FREQUENCY
13.5
-35
Bypass 1 VPP
Total Harmonic Distortion (dBc)
Large-Signal Gain (dB)
13.0
Bypass 2 VPP
SD Filter
12.5
HD Filter
11.5
11.0
10.5
10.0
Full-HD Filter
ED Filter
VS+ = 3.3 V
Load =
150 W || 5 pF
DC-Coupled
Output
VO = 2 VPP
ED Filter
-40
HD Filter
-45
SD Filter
-50
-55
-60
-65
-70
Full-HD Filter
-75
-80
9.5
1M
10 M
-85
1G
100 M
1G
100 M
Frequency (Hz)
SF CHANNELS LARGE-SIGNAL GAIN vs FREQUENCY
RESPONSE
12.0
10 M
Frequency (Hz)
Bypass
1M
10 M
Frequency (Hz)
VS+ = 3.3 V
RL = 150 W || 5 pF
DC-Coupled Output
VO = 1.4 VPP
100 M
Frequency (Hz)
Figure 22.
Figure 23.
SF CHANNELS 0.5-VPP THD vs FREQUENCY
Total Harmonic Distortion (dBc)
-45
ED Filter
-50
SD Filter
-55
HD Filter
-60
-65
-70
-75
-80
Full-HD Filter
-85
-90
-95
Bypass
1M
VS+ = 3.3 V
RL = 150 W || 5 pF
DC-Coupled Output
VO = 0.5 VPP
10 M
100 M
Frequency (Hz)
Figure 24.
18
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS7360
THS7360
www.ti.com
SLOS674 – JUNE 2010
TYPICAL CHARACTERISTICS: 5 V, Standard-Definition (SD) Channels
With load = 150 Ω || 5 pF, dc-coupled input and output, unless otherwise noted.
SD CHANNELS SMALL-SIGNAL GAIN vs FREQUENCY
RESPONSE
SD CHANNELS SMALL-SIGNAL GAIN vs FREQUENCY
RESPONSE
20
15.5
15.0
0
-10
VS+ = 5 V
Load = RL || 10 pF
DC-Coupled Output
VO = 200 mVPP
Small-Signal Gain (dB)
Small-Signal Gain (dB)
10
-20
RL = 150 W, Filter Mode
RL = 75 W, Filter Mode
RL = 150 W, Bypass Mode
RL = 75 W, Bypass Mode
-30
-40
-50
100 k
1M
14.5
14.0
VS+ = 5 V
Load = RL || 10 pF
DC-Coupled Output
VO = 200 mVPP
13.5
13.0
RL = 150 W, Filter Mode
RL = 75 W, Filter Mode
RL = 150 W, Bypass Mode
RL = 75 W, Bypass Mode
12.5
12.0
10 M
100 M
11.5
100 k
1G
1M
Figure 25.
Figure 26.
SD CHANNELS PHASE vs FREQUENCY RESPONSE
SD CHANNELS GROUP DELAY vs FREQUENCY
RESPONSE
120
45
RL = 75 W and 150 W
Bypass Mode
0
110
Group Delay (ns)
-45
Phase (°)
-90
-135
RL = 75 W and 150 W
Filter Mode
-180
-225
-270
-315
VS+ = 5 V
Load = RL || 10 pF
DC-Coupled Output
VO = 200 mVPP
-360
100 k
100
VS+ = 5 V
Load = RL || 10 pF
DC-Coupled Output
VO = 200 mVPP
90
80
RL = 75 W and 150 W
Filter Mode
70
60
1M
100 M
10 M
50
100 k
1G
1M
100 M
10 M
Frequency (Hz)
Frequency (Hz)
Figure 27.
Figure 28.
SD CHANNELS LARGE-SIGNAL GAIN vs FREQUENCY
RESPONSE
SD CHANNELS LARGE-SIGNAL GAIN vs FREQUENCY
RESPONSE
20
15.5
Bypass Mode
Bypass Mode
15.0
10
Filter Mode
Large-Signal Gain (dB)
Large-Signal Gain (dB)
100 M
10 M
Frequency (Hz)
Frequency (Hz)
0
VO = 0.2 VPP
-10
VO = 1 VPP
-20
VO = 2 VPP
-30
-40
VO = 0.2 VPP
VS+ = 5 V
Load = 150 W || 10 pF
DC-Coupled Output
-50
100 k
1M
14.0
13.5
10 M
100 M
1G
VO = 0.2 VPP and 2 VPP
13.0
12.5
12.0
VO = 2 VPP
VO = 0.2 VPP
Filter Mode
14.5
VS+ = 5 V
Load = 150 W || 10 pF
DC-Coupled Output
11.5
100 k
VO = 2 VPP
VO = 1 VPP
1M
10 M
100 M
Frequency (Hz)
Frequency (Hz)
Figure 29.
Figure 30.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS7360
19
THS7360
SLOS674 – JUNE 2010
www.ti.com
TYPICAL CHARACTERISTICS: 5 V, Standard-Definition (SD) Channels (continued)
With load = 150 Ω || 5 pF, dc-coupled input and output, unless otherwise noted.
SD CHANNELS SMALL-SIGNAL GAIN vs FREQUENCY
RESPONSE
20
SD CHANNELS SMALL-SIGNAL GAIN vs FREQUENCY
RESPONSE
15.5
Bypass Mode
Bypass Mode
15.0
Filter Mode
0
AC
-10
DC
-20
VS+ = 5 V
Load = 150 W || 10 pF
AC- vs DC-Coupled Output
VO = 0.2 VPP
-30
-40
-50
100 k
1M
DC
Small-Signal Gain (dB)
Small-Signal Gain (dB)
10
VS+ = 5 V
Load = 150 W || 10 pF
AC- vs DC-Coupled Output
VO = 0.2 VPP
14.5
14.0
13.5
DC
13.0
AC or DC
Filter Mode
12.5
12.0
AC
10 M
11.5
100 k
1G
100 M
1M
Figure 31.
Figure 32.
SD CHANNELS 0.5-VPP THD vs FREQUENCY
-45
-40
-50
-45
-50
SD Filter
-60
-65
VS+ = 5 V
RL = 150 W || 5 pF
DC-Coupled Output
VO = 1.4 VPP
Bypass SD
-75
-80
-85
1M
Total Harmonic Distortion (dBc)
Total Harmonic Distortion (dBc)
SD CHANNELS 1.4-VPP THD vs FREQUENCY
-35
-70
-55
-60
-65
SD Filter
-70
-75
-80
-95
1M
Frequency (Hz)
Figure 33.
Figure 34.
SD CHANNELS DIFFERENTIAL PHASE
0.50
-0.05
0.45
NTSC
VS+ = 5 V
Filter Mode
0.40
-0.10
Differential Phase (°)
Differential Gain (%)
SD CHANNELS DIFFERENTIAL GAIN
PAL
-0.20
-0.25
-0.30
-0.40
0.35
0.30
PAL
0.25
0.20
NTSC
0.15
0.10
VS+ = 5 V
Filter Mode
1st
0.05
0
2nd
3rd
4th
5th
6th
Figure 35.
20
100 M
10 M
Frequency (Hz)
0
-0.35
VS+ = 5 V
RL = 150 W || 5 pF
DC-Coupled Output
VO = 0.5 VPP
Bypass SD
-85
-90
100 M
10 M
-0.15
100 M
10 M
Frequency (Hz)
Frequency (Hz)
-55
AC
1st
2nd
3rd
4th
5th
6th
Figure 36.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS7360
THS7360
www.ti.com
SLOS674 – JUNE 2010
TYPICAL CHARACTERISTICS: 5 V, Selectable Filter (SF) Channels
With load = 150 Ω || 5 pF, dc-coupled input and output, unless otherwise noted.
SF CHANNELS SMALL-SIGNAL GAIN vs FREQUENCY
RESPONSE
SF CHANNELS SMALL-SIGNAL GAIN vs FREQUENCY
RESPONSE
20
13.5
DC-Coupled Output
Bypass
13.0
SD Filter
Small-Signal Gain (dB)
Small-Signal Gain (dB)
10
0
ED Filter
Full-HD
Filter
-10
HD Filter
-20
VS+ = 5 V
Load = 150 W || 5 pF
DC-Coupled Output
VO = 200 mVPP
-30
-40
12.5
SD Filter
12.0
Full-HD
Filter
11.0
10.5
10.0
-50
VS+ = 5 V
Load =
150 W || 5 pF
VO = 200 mVPP
HD Filter
9.5
1M
10 M
1M
1G
100 M
10 M
1G
100 M
Frequency (Hz)
Frequency (Hz)
Figure 37.
Figure 38.
SF CHANNELS PHASE vs FREQUENCY RESPONSE
SF CHANNELS GROUP DELAY vs FREQUENCY
RESPONSE
100
45
Bypass
0
90
Full-HD Filter
-45
HD Filter
-135
ED Filter
-180
-225
-270
-315
Group Delay (ns)
80
-90
Phase (°)
Bypass
ED Filter
11.5
SD Filter
VS+ = 5 V
Load = 150 W || 5 pF
DC-Coupled Output
VO = 200 mVPP
-360
100 k
1M
VS+ = 5 V
Load = 150 W || 5 pF
DC-Coupled Output
VO = 200 mVPP
70
60
SD Filter
50
40
30
10 M
100 M
ED Filter
20
100 k
1G
1M
10 M
100 M
Frequency (Hz)
Frequency (Hz)
Figure 39.
Figure 40.
SF CHANNELS GROUP DELAY vs FREQUENCY RESPONSE
35
Group Delay (ns)
30
VS+ = 5 V
Load = 150 W || 5 pF
DC-Coupled Output
VO = 200 mVPP
25
20
HD Filter
15
Full-HD Filter
10
5
1M
10 M
100 M
Frequency (Hz)
Figure 41.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS7360
21
THS7360
SLOS674 – JUNE 2010
www.ti.com
APPLICATION INFORMATION
The THS7360 is targeted for six-channel video output
applications that require three standard-definition
(SD) video output buffers and three selectable filter
(SF) output buffers. Although it can be used for
numerous other applications, the needs and
requirements of the video signal are the most
important design parameters of the THS7360. Built
on the revolutionary, complementary Silicon
Germanium (SiGe) BiCom3X process, the THS7360
incorporates many features not typically found in
integrated video parts while consuming very low
power. The THS7360 includes the following features:
• Single-supply 2.7-V to 5-V operation with low total
quiescent current of 24.5 mA at 3.3 V and
25.5 mA at 5 V
• Disable mode allows for shutting down individual
SD/SF blocks of amplifiers to save system power
in power-sensitive applications
• Input configuration accepts dc + level shift, ac
sync-tip clamp, or ac-bias
– AC-biasing is allowed with the use of external
pull-up resistors to the positive power supply
• Sixth-order, low-pass filter for DAC reconstruction
or ADC image rejection:
– 9.5 MHz for NTSC, PAL, SECAM, composite
video (CVBS), S-Video Y’/C’, 480i/576i,
Y’/P’B/P’R, and G’B’R’ (R’G’B’) signals
– Selectable 9.2-MHz/17-MHz/35-MHz/70-MHz
for
480i/576i,
480p/576p,
720p/1080i/1080p24/1080p30, or 1080p60
Y’/P’ B/P’R or G’B’R’ signals; also allows up to
QXGA (1600 × 1200 at 60 Hz) R'G'B' video
• Individually-controlled Bypass mode bypasses the
low-pass filters for each SD/SF block of amplifiers
– SD bypass mode features 60-MHz and
150-V/ms performance
– SF bypass mode features 280-MHz and
800-V/ms performance
• Individually-controlled Disable mode shuts down
all amplifiers in each SD/SF block to reduce
quiescent current to 0.1 mA
• Internally-fixed gain of 5.6-V/V (+15-dB) for SD
channels or 4.5-V/V (+13.1-dB) for SF channels
22
•
•
All outputs can drive two video lines with
dc-coupling or traditional ac-coupling
Flow-through configuration using a TSSOP-20
package that complies with the latest lead-free
(RoHS-compatible) and green manufacturing
requirements
OPERATING VOLTAGE
The THS7360 is designed to operate from 2.7 V to
5 V over the –40°C to +85°C temperature range. The
impact on performance over the entire temperature
range is negligible as a result of the implementation
of thin film resistors and high-quality, low-temperature
coefficient capacitors. The design of the THS7360
allows operation down to 2.6 V, but it is
recommended to use at least a 3-V supply to ensure
that no issues arise with headroom or clipping with
100% color-saturated CVBS signals. If only 75% color
saturated CVBS is supported, then the output voltage
requirements are reduced to 2 VPP on the output,
allowing a 2.7-V supply to be utilized without issues.
A 0.1-mF to 0.01-mF capacitor should be placed as
close as possible to the power-supply pins. Failure to
do so may result in the THS7360 outputs ringing or
oscillating. Additionally, a large capacitor (such as
22 mF to 100 mF) should be placed on the
power-supply line to minimize interference with
50-/60-Hz line frequencies.
INPUT VOLTAGE
The THS7360 input range allows for an input signal
range from –0.2 V to approximately (VS+ – 1.5 V).
However, because of the internal fixed gain of
5.6 V/V (+15 dB) on the SD channels or 4.5 V/V
(+13.1dB) and the internal input level shift of 120 mV
(typical), the output is generally the limiting factor for
the allowable linear input range. For example, with a
5-V supply, the linear input range is from –0.2 V to
3.5 V. However, because of the gain and level shift,
the linear output range limits the allowable linear
input range to approximately –0.08 V to 0.8 V.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS7360
THS7360
www.ti.com
SLOS674 – JUNE 2010
INPUT OVERVOLTAGE PROTECTION
These diodes provide moderate protection to input
overdrive voltages above and below the supplies as
well. The protection diodes can typically support
30 mA of continuous current when overdriven.
The THS7360 is built using a very high-speed,
complementary, bipolar CMOS process. The internal
junction breakdown voltages are relatively low for
these very small geometry devices. These
breakdowns are reflected in the Absolute Maximum
Ratings table. All input and output device pins are
protected with internal ESD protection diodes to the
power supplies, as shown in Figure 42.
TYPICAL CONFIGURATION AND VIDEO
TERMINOLOGY
A typical application circuit using the THS7360 as a
video buffer is shown in Figure 43. It shows a DAC or
encoder driving the input channels of the THS7360.
One channel is a CVBS connection while two other
channels are for the S-Video Y’/C’ signals of an SD
video system. These signals can be NTSC, PAL, or
SECAM signals. The other three channels are the
component video Y’/P’B/P’R (sometimes labeled
Y’U’V’ or incorrectly labeled Y’/C’B/C’R) signals. These
signals are typically 480i, 576i, 480p, 576p, 720p,
1080i, or up to 1080p60 signals. Because the filters
can be bypassed, other formats such as R'G'B' video
up to QXGA or UWXGA can also be supported with
the THS7360.
+VS
External
Input/Output
Pin
Internal
Circuitry
Figure 42. Internal ESD Protection
THS7360
CVBS
75 W
CVBS
R
SD1 IN
SD1 OUT 20
2
SD2 IN
SD2 OUT 19
3
SD3 IN
SD3 OUT 18
75 W
S-Video Y' Out
75 W
S-Video Y’
R
SOC/DAC/Encoder
1
+2.7 V to
+5 V
S-Video C’
R
Y'/G'
4
NC
Disable SD 17
5
VS+
GND 16
6
NC
Disable SF 15
7
SF1 IN
SF1 OUT 14
8
SF2 IN
SF2 OUT 13
9
SF3 IN
SF3 OUT 12
10
Bypass SD
Bypass SF 11
Disable SD
75 W
Disable SF
S-Video C' Out
75 W
75 W
Y'/G' Out
75 W
R
75 W
Bypass
SD LPF
P'B/B'
Bypass
SF LPF
P'B/B' Out
75 W
R
75 W
P'R/R' Out
P'R/R'
75 W
R
75 W
(1) SF indicates selectable filter.
Figure 43. Typical Six-Channel System Inputs from DC-Coupled Encoder/DAC with DC-Coupled Line
Driving
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS7360
23
THS7360
SLOS674 – JUNE 2010
www.ti.com
Note that the Y’ term is used for the luma channels
throughout this document rather than the more
common luminance (Y) term. This usage accounts for
the definition of luminance as stipulated by the
International Commission on Illumination (CIE). Video
departs from true luminance because a nonlinear
term, gamma, is added to the true RGB signals to
form R’G’B’ signals. These R’G’B’ signals are then
used to mathematically create luma (Y’). Thus,
luminance (Y) is not maintained, providing a
difference in terminology.
This rationale is also used for the chroma (C’) term.
Chroma is derived from the nonlinear R’G’B’ terms
and, thus, it is nonlinear. Chominance (C) is derived
from linear RGB, giving the difference between
chroma (C’) and chrominance (C). The color
difference signals (P’B/P’R/U’/V’) are also referenced
in this manner to denote the nonlinear (gamma
corrected) signals.
R’G’B’ (commonly mislabeled RGB) is also called
G’B’R’ (again commonly mislabeled as GBR) in
professional video systems. The Society of Motion
Picture
and
Television
Engineers
(SMPTE)
component standard stipulates that the luma
information is placed on the first channel, the blue
color difference is placed on the second channel, and
the red color difference signal is placed on the third
channel. This practice is consistent with the Y'/P'B/P'R
nomenclature. Because the luma channel (Y') carries
the sync information and the green channel (G') also
carries the sync information, it makes logical sense
that G' be placed first in the system. Because the
blue color difference channel (P'B) is next and the red
color difference channel (P'R) is last, then it also
makes logical sense to place the B' signal on the
second channel and the R' signal on the third
channel, respectfully. Thus, hardware compatibility is
better achieved when using G'B'R' rather than R'G'B'.
Note that for many G'B'R' systems, sync is embedded
on all three channels, but this configuration may not
always be the case in all systems.
24
INPUT MODE OF OPERATION: DC
The inputs to the THS7360 allow for both ac- and
dc-coupled inputs. Many DACs or video encoders can
be dc-connected to the THS7360. One of the
drawbacks to dc-coupling is when 0 V is applied to
the input. Although the input of the THS7360 allows
for a 0-V input signal without issue, the output swing
of a traditional amplifier cannot yield a 0-V signal,
resulting in possible clipping. This limitation is true for
any single-supply amplifier because of the
characteristics of the output transistors. Neither
CMOS nor bipolar transistors can achieve 0 V while
sinking current. This transistor characteristic is also
the same reason why the highest output voltage is
always less than the power-supply voltage when
sourcing current.
This output clipping can reduce the sync amplitudes
(both horizontal and vertical sync) on the video
signal. A problem occurs if the video signal receiver
uses an automatic gain control (AGC) loop to account
for losses in the transmission line. Some video AGC
circuits derive gain from the horizontal sync
amplitude. If clipping occurs on the sync amplitude,
then the AGC circuit can increase the gain too
much—resulting in too much luma and/or chroma
amplitude gain correction. This correction may result
in a picture with an overly bright display with too
much color saturation.
Other AGC circuits use the chroma burst amplitude
for amplitude control; reduction in the sync signals
does not alter the proper gain setting. However, it is
good engineering design practice to ensure that
saturation/clipping does not take place. Transistors
always take a finite amount of time to come out of
saturation. This saturation could possibly result in
timing delays or other aberrations on the signals.
To eliminate saturation or clipping problems, the
THS7360 has an input level shift feature. The
resulting output with a 0-V applied input signal is
approximately 120 mV. The THS7360 rail-to-rail
output stage can create this output level while
connected to a typical video load. This configuration
ensures that no saturation or clipping of the sync
signals occur. This shift is constant, regardless of the
input signal. For example, if a 0.1-V input is applied
to the SD channel, the output is 0.1V X 5.6 V/V +
0.12V = 0.68 V.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS7360
THS7360
www.ti.com
SLOS674 – JUNE 2010
Because the internal gain is fixed, the gain dictates
what the allowable linear input voltage range can be
without clipping concerns. For example, if the power
supply is set to 3 V, the maximum output is
approximately 2.9 V while driving a significant amount
of current. Thus, to avoid clipping on the SD
channels, the allowable input is (2.9 V - 0.12V)/5.6 =
0.5 V. This range is valid for up to the maximum
recommended 5-V power supply that allows
approximately a (4.9 V – 0.12 V)/5.6 = 0.85 V input
range while avoiding clipping on the output.
The input impedance of the THS7360 in this mode of
operation is dictated by the internal, 800-kΩ
pull-down resistor, as shown in Figure 44. Note that
the internal voltage shift does not appear at the input
pin; it only shows at the output pin.
+VS
Internal
Circuitry
Input
Pin
800 kW
Level
Shift
Figure 44. Equivalent DC Input Mode Circuit
INPUT MODE OF OPERATION: AC SYNC TIP
CLAMP
go below 0 V, the THS7360 internal control loop
sources up to 6 mA of current to increase the input
voltage level on the THS7360 input side of the
coupling capacitor. As soon as the voltage goes
above the 0-V level, the loop stops sourcing current
and becomes very high impedance.
One of the concerns about the STC level is how the
clamp reacts to a sync edge that has
overshoot—common in VCR signals, noise, DAC
overshoot, or reflections found in poor printed circuit
board (PCB) layouts. Ideally, the STC should not
react to the overshoot voltage of the input signal.
Otherwise, this response could result in clipping on
the rest of the video signal because it may raise the
bias voltage too much.
To help minimize this input signal overshoot problem,
the control loop in the THS7360 has an internal
low-pass filter, as shown in Figure 45. This filter
reduces the response time of the STC circuit. This
delay is a function of how far the voltage is below
ground, but in general it is approximately a 400-ns
delay for the SD channel filters and approximately a
150-ns delay for the SF filters. The effect of this filter
is to slow down the response of the control loop so as
not to clamp on the input overshoot voltage but rather
the flat portion of the sync signal.
As a result of this delay, sync may have an apparent
voltage shift. The amount of shift depends on the
amount of droop in the signal as dictated by the input
capacitor and the STC current flow. Because sync is
used primarily for timing purposes, with syncing
occurring on the edge of the sync signal, this shift is
transparent in most systems.
Some video DACs or encoders are not referenced to
ground but rather to the positive power supply. The
resulting video signals are generally at too great a
voltage for a dc-coupled video buffer to function
properly. To account for this scenario, the THS7360
incorporates a sync-tip clamp circuit. This function
requires a capacitor (nominally 0.1 mF) to be in series
with the input. Although the term sync-tip-clamp is
used throughout this document, it should be noted
that the THS7360 would probably be better termed as
a dc restoration circuit based on how this function is
performed. This circuit is an active clamp circuit and
not a passive diode clamp function.
Figure 45. Equivalent AC Sync-Tip-Clamp Input
Circuit
The input to the THS7360 has an internal control loop
that sets the lowest input applied voltage to clamp at
ground (0 V). By setting the reference at 0 V, the
THS7360 allows a dc-coupled input to also function.
Therefore, the sync-tip-clamp (STC) is considered
transparent because it does not operate unless the
input signal goes below ground. The signal then goes
through the same level shifter, resulting in an output
voltage low level of 120 mV. If the input signal tries to
While this feature may not fully eliminate overshoot
issues on the input signal, in cases of extreme
overshoot and/or ringing, the STC system should help
minimize improper clamping levels. As an additional
method to help minimize this issue, an external
capacitor (for example, 10 pF to 47 pF) to ground in
parallel with the external termination resistors can
help filter overshoot problems.
+VS
Internal
Circuitry
STC LPF
+VS
gm
Input
0.1 mF Input
Pin
800 kW
Level
Shift
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS7360
25
THS7360
SLOS674 – JUNE 2010
www.ti.com
It should be noted that this STC system is dynamic
and does not rely upon timing in any way. It only
depends on the voltage that appears at the input pin
at any given point in time. The STC filtering helps
minimize level shift problems associated with
switching noises or very short spikes on the signal
line. This architecture helps ensure a very robust
STC system.
When the ac STC operation is used, there must also
be some finite amount of discharge bias current. As
previously described, if the input signal goes below
the 0-V clamp level, the internal loop of the THS7360
sources current to increase the voltage appearing at
the input pin. As the difference between the signal
level and the 0-V reference level increases, the
amount
of
source
current
increases
proportionally—supplying up to 6 mA of current.
Thus, the time to re-establish the proper STC voltage
can be very fast. If the difference is very small, then
the source current is also very small to account for
minor voltage droop.
However, what happens if the input signal goes
above the 0-V input level? The problem is that the
video signal is always above this level and must not
be altered in any way. As a result, if the sync level of
the input signal is above this 0-V level, then the
internal discharge (sink) current reduces the
ac-coupled bias signal to the proper 0-V level.
This discharge current must not be large enough to
alter the video signal appreciably or picture quality
issues may arise. This effect is often seen by looking
at the tilt (droop) of a constant luma signal being
applied and the resulting output level. The associated
change in luma level from the beginning and end of
the video line is the amount of line tilt (droop).
If the discharge current is very small, the amount of
tilt is very low, which is a generally a good thing.
However, the amount of time for the system to
capture the sync signal could be too long. This effect
is also termed hum rejection. Hum arises from the ac
line voltage frequency of 50 Hz or 60 Hz. The value
of the discharge current and the ac-coupling capacitor
combine to dictate the hum rejection and the amount
of line tilt.
To allow for both dc- and ac-coupling in the same
part, the THS7360 incorporates an 800-kΩ resistor to
ground. Although a true constant current sink is
preferred over a resistor, there can be issues when
the voltage is near ground. This configuration can
cause the current sink transistor to saturate and
cause potential problems with the signal. The 800-kΩ
resistor is large enough to not impact a dc-coupled
DAC termination. For discharging an ac-coupled
source, Ohm’s Law is used. If the video signal is
0.5 V, then there is 0.5 V/800 kΩ = 0.625-mA of
discharge current. If more hum rejection is desired or
26
there is a loss of sync occurring, then simply
decrease the 0.1-mF input coupling capacitor. A
decrease from 0.1 mF to 0.047 mF increases the hum
rejection by a factor of 2.1. Alternatively, an external
pull-down resistor to ground may be added that
decreases the overall resistance and ultimately
increases the discharge current.
To ensure proper stability of the ac STC control loop,
the source impedance must be less than 1-kΩ with
the input capacitor in place. Otherwise, there is a
possibility of the control loop ringing, which may
appear on the output of the THS7360. Because most
DACs or encoders use resistors to establish the
voltage, which are typically less than 300-Ω, meeting
the less than 1-kΩ requirement is easily done.
However, if the source impedance looking from the
THS7360 input perspective is very high, then simply
adding a 1-kΩ resistor to GND ensures proper
operation of the THS7360.
INPUT MODE OF OPERATION: AC BIAS
Sync-tip clamps work very well for signals that have
horizontal and/or vertical syncs associated with them;
however, some video signals do not have a sync
embedded within the signal. If ac-coupling of these
signals is desired, then a dc bias is required to
properly set the dc operating point within the
THS7360. This function is easily accomplished with
the THS7360 by simply adding an external pull-up
resistor to the positive power supply, as shown in
Figure 46.
+3.3 V
+3.3 V
CIN
0.1 mF
Input
Internal
Circuitry
RPU
Input
Pin
800 kW
Level
Shift
Figure 46. AC-Bias Input Mode Circuit
Configuration
The dc voltage appearing at the input pin is equal to
Equation 1:
VDC = VS
Submit Documentation Feedback
800 kW
800 kW + RPU
(1)
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS7360
THS7360
www.ti.com
SLOS674 – JUNE 2010
The THS7360 allowable input range is approximately
0 V to (VS+ – 1.5 V), allowing for a very wide input
voltage range. As such, the input dc bias point is very
flexible, with the output dc bias point being the
primary factor. For example, if the output dc bias
point on a SD channel is desired to be 1.6 V on a
3.3-V supply, then the input dc bias point should be
(1.6 V – 120 mV)/5.6 = 0.264 V. Thus, the pull-up
resistor calculates to approximately 9.31 MΩ,
resulting in 0.261 V. If the output dc-bias point is
desired to be 1.6 V with a 5-V power supply, then the
pull-up resistor calculates to approximately 14.3 MΩ.
Keep in mind that the internal 800-kΩ resistor has
approximately a ±20% variance. As such, the
calculations should take this variance into account.
For the 0.261-V example above, using an ideal
9.31-MΩ resistor, the input dc bias voltage is
approximately 0.261 V ± 0.05 V.
The value of the output bias voltage is very flexible
and is left to each individual design. It is important to
ensure that the signal does not clip or saturate the
video signal. Thus, it is recommended to ensure the
output bias voltage is between 0.9 V and (VS+ – 1 V).
For 100% color saturated CVBS or signals with
Macrovision®, the CVBS signal can reach up to
1.23 VPP at the input, or 2.46 VPP at the output of the
THS7360. In contrast, other signals are typically
1 VPP or 0.7 VPP at the input, which translate to an
output voltage of 2 VPP or 1.4 VPP, respectively. The
output bias voltage must account for a worst-case
situation, depending on the signals involved.
One other issue that must be taken into account is
the dc-bias point is a function of the power supply. As
such, there is an impact on system PSRR. To help
reduce this impact, the input capacitor combines with
the pull-up resistance to function as a low-pass filter.
Additionally, the time to charge the capacitor to the
final dc bias point is a function of the pull-up resistor
and the input capacitor size. Lastly, the input
capacitor forms a high-pass filter with the parallel
impedance of the pull-up resistor and the 800-kΩ
resistor. In general, it is good to have this high-pass
filter at approximately 3 Hz to minimize any potential
droop on a P’B or P’R signal. A 0.1-mF input capacitor
with a 9.31-MΩ pull-up resistor equates to
approximately a 2.2-Hz high-pass corner frequency.
This mode of operation is recommended for use with
chroma (C’), P’B, P’R, U’, and V’ signals. This method
can also be used with sync signals if desired. The
benefit of using the STC function over the ac-bias
configuration on embedded sync signals is that the
STC maintains a constant back-porch voltage as
opposed to a back-porch voltage that fluctuates
depending on the video content. Because the
high-pass corner frequency is a very low 2.2 Hz, the
impact on the video signal is negligible relative to the
STC configuration.
OUTPUT MODE OF OPERATION:
DC-COUPLED
The THS7360 incorporates a rail-to-rail output stage
that can be used to drive the line directly without the
need for large ac-coupling capacitors. This design
offers the best line tilt and field tilt (droop)
performance because no ac-coupling occurs. Keep in
mind that if the input is ac-coupled, then the resulting
tilt as a result of the input ac-coupling continues to be
seen on the output, regardless of the output coupling.
The 80-mA output current drive capability of the
THS7360 is designed to drive two video lines
simultaneously—essentially, a 75-Ω load—while
keeping the output dynamic range as wide as
possible. Figure 47 shows the THS7360 driving two
video lines while keeping the output dc-coupled.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS7360
27
THS7360
SLOS674 – JUNE 2010
www.ti.com
CVBS 1 Out
75 W
CVBS 1 Out
75 W
THS7360
CVBS
R
S-Video Y’
SOC/DAC/Encoder
R
+2.7 V to
+5 V
S-Video C’
R
Y'/G'
1
SD1 IN
SD1 OUT 20
2
SD2 IN
SD2 OUT 19
3
SD3 IN
SD3 OUT 18
4
NC
Disable SD 17
75 W
75 W
S-Video Y' 1 Out
75 W
Disable SD
S-Video Y' 1 Out
75 W
75 W
5
VS+
GND 16
6
NC
Disable HD 15
7
SF1 IN
SF1 OUT 14
8
SF2 IN
SF2 OUT 13
S-Video C' 1 Out
9
SF3 IN
SF3 OUT 12
75 W
10
Bypass SD
Disable SF
75 W
S-Video C' 1 Out
75 W
Bypass SF 11
75 W
75 W
R
Y'/G' 1 Out
75 W
Bypass
SD LPF
P'B/B'
Y'/G' 1 Out
Bypass
SF LPF
75 W
75 W
R
75 W
P'B/B' 1 Out
75 W
P'R/R'
R
P’B/B' 1 Out
75 W
75 W
75 W
P’R/R' 1 Out
75 W
P'R/R' 1 Out
75 W
75 W
75 W
(1) SF indicates selectable filter.
Figure 47. Typical Six-Channel System with DC-Coupled Line Driving and Two Outputs Per Channel
One concern of dc-coupling arises, however, if the
line is terminated to ground. If the ac-bias input
configuration is used, the output of the THS7360 has
a dc bias on the output, such as 1.6 V. With two lines
terminated to ground, this configuration allows a dc
current path to flow, such as 1.6 V/75 Ω = 21.3 mA.
The result of this configuration is a slightly decreased
high-output voltage swing and an increase in power
dissipation of the THS7360. While the THS7360 was
designed to operate with a junction temperature of up
to +125°C, care must be taken to ensure that the
junction temperature does not exceed this level or
else long-term reliability could suffer. Using a 5-V
supply, this configuration can result in an additional
dc power dissipation of (5 V – 1.6 V) × 21.3 mA =
72.5 mW per channel. With a 3.3-V supply, this
dissipation reduces to 36.2 mW per channel. The
overall low quiescent current of the THS7360 design
minimizes potential thermal issues even when using
the TSSOP package at high ambient temperatures,
28
but power and thermal analysis should always be
examined in any system to ensure that no issues
arise. Be sure to use RMS power and not
instantaneous power when evaluating the thermal
performance.
Note that the THS7360 can drive the line with
dc-coupling regardless of the input mode of
operation. The only requirement is to make sure the
video line has proper termination in series with the
output (typically 75 Ω). This requirement helps isolate
capacitive loading effects from the THS7360 output.
Failure to isolate capacitive loads may result in
instabilities with the output buffer, potentially causing
ringing or oscillations to appear. The stray
capacitance that appears directly at the THS7360
output pins should be kept below 20 pF for the fixed
SD filter channels and below 15 pF for the selectable
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS7360
THS7360
www.ti.com
SLOS674 – JUNE 2010
filter channels. One way to help ensure this condition
is satisfied is to make sure the 75-Ω source resistor is
placed within 0.5-inches to each THS7360 output pin.
If a large ac-coupling capacitor is used, the capacitor
should be placed after this resistor.
There are many reasons dc-coupling is desirable,
including reduced costs, PCB area, and no line tilt. A
common question is whether or not there are any
drawbacks to using dc-coupling. There are some
potential issues that must be examined, such as the
dc current bias as discussed above. Another potential
risk is whether this configuration meets industry
standards.
EIA/CEA-770
stipulates
that
the
back-porch shall be 0 V ± 1 V as measured at the
receiver. With a double-terminated load system, this
requirement implies a 0-V ± 2-V level at the video
amplifier output. The THS7360 can easily meet this
requirement without issue. However, in Japan, the
EIAJ CP-1203 specification stipulates a 0-V ± 0.1-V
level with no signal. This requirement can be met with
the THS7360 in shutdown mode, but while active it
cannot meet this specification without output
ac-coupling. AC-coupling the output essentially
ensures that the video signal works with any system
and any specification. For many modern systems,
however, dc-coupling can satisfy most needs.
OUTPUT MODE OF OPERATION:
AC-COUPLED
A very common method of coupling the video signal
to the line is with a large capacitor. This capacitor is
typically between 220 mF and 1000 mF, although
470 mF is very typical. The value of this capacitor
must be large enough to minimize the line tilt (droop)
and/or field tilt associated with ac-coupling as
described previously in this document. AC-coupling is
performed for several reasons, but the most common
is to ensure full interoperability with the receiving
video system. This approach ensures that regardless
of the reference dc voltage used on the transmitting
side, the receiving side re-establishes the dc
reference voltage to its own requirements.
In the same way as the dc output mode of operation
discussed previously, each line should have a 75-Ω
source termination resistor in series with the
ac-coupling capacitor. This 75-Ω resistor should be
placed next to the THS7360 output to minimize
capacitive loading effects. If two lines are to be
driven, it is best to have each line use its own
capacitor and resistor rather than sharing these
components. This configuration helps ensure
line-to-line dc isolation and eliminates the potential
problems as described previously. Using a single,
1000-mF capacitor for two lines is permissible, but
there is a chance for interference between the two
receivers.
Lastly, because of the edge rates and frequencies of
operation, it is recommended (but not required) to
place a 0.1-mF to 0.01-mF capacitor in parallel with
the large 220-mF to 1000-mF capacitor. These large
value capacitors are most commonly aluminum
electrolytic. It is well-known that these capacitors
have significantly large equivalent series resistance
(ESR), and the impedance at high frequencies is
rather large as a result of the associated inductances
involved with the leads and construction. The small
0.1-mF to 0.01-mF capacitors help pass these
high-frequency signals (greater than 1 MHz) with
much lower impedance than the large capacitors.
Although it is common to use the same capacitor
values for all the video lines, the frequency bandwidth
of the chroma signal in a S-Video system is not
required to go as low (or as high of a frequency) as
the luma channels. Thus, the capacitor values of the
chroma line(s) can be smaller, such as 0.1 mF.
Figure 48 shows a typical configuration where the
input is ac-coupled and the output is also ac-coupled.
AC-coupled inputs are generally required when
current-sink DACs are used or the input is connected
to an unknown source, such as when the THS7360 is
used as an input device.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS7360
29
THS7360
SLOS674 – JUNE 2010
www.ti.com
THS7360
(1)
0.1 mF
R
(1)
0.1 mF
+2.7 V to
+5 V
R
(1)
0.1 mF
R
(1)
0.1 mF
+V
Y'/G'
SD2 OUT 19
3
SD3 IN
SD3 OUT 18
4
NC
Disable SD 17
5
VS+
GND 16
6
NC
Disable HD 15
7
SF1 IN
SF1 OUT 14
8
SF2 IN
SF2 OUT 13
9
SF3 IN
SF3 OUT 12
10
Bypass SD
75 W
(2)
Y' Out
330 mF
75 W
Disable SD
To GPIO or
GND/VS+
75 W
Disable SF
(2)
330 mF
75 W
P’B Out
+
S-Video C’
SD2 IN
75 W
75 W
(2)
330 mF
Y' Out
+
SOC/DAC/Encoder
+V
SD1 IN
2
+
RPU
S-Video Y’
1
+
CVBS
+V
(2)
330 mF
75 W
SD1 OUT 20
Bypass SF 11
75 W
R
(1)
75 W
(2)
330 mF
P'B Out
+
Bypass
SF LPF
Bypass
SD LPF
0.1 mF
+V
P'B/B'
75 W
R
To GPIO or
GND/VS+
(1)
0.1 mF
75 W
P'R/R'
R
RPU
(2)
330 mF
P'R Out
+
+V
75 W
RPU
+V
+2.7 V to +5 V
(1) AC-coupled input is shown in this example. DC-coupling is also allowed as long as the DAC output voltage is within the allowable linear
input and output voltage range of the THS7360. To apply dc-coupling, remove the 0.1-mF input capacitors and the RPU pull-up resistors along
with connecting the DAC termination resistors (R) to ground.
(2) This example shows an ac-coupled output. DC-coupling is also allowed by simply removing these capacitors.
(3) SF indicates selectable filter.
Figure 48. Typical AC Input System Driving AC-Coupled Video Lines
LOW-PASS FILTER
Each channel of the THS7360 incorporates a
sixth-order,
low-pass
filter.
These
video
reconstruction filters minimize DAC images from
being passed onto the video receiver. Depending on
the receiver design, failure to eliminate these DAC
images can cause picture quality problems because
of aliasing of the ADC in the receiver. Another benefit
of the filter is to smooth out aberrations in the signal
that some DACs can have if the internal filtering is
not very good. This benefit helps with picture quality
and ensures that the signal meets video bandwidth
requirements.
Each filter has an associated Butterworth
characteristic. The benefit of the Butterworth
response is that the frequency response is flat, with a
relatively steep initial attenuation at the corner
frequency. The problem with this characteristic is that
the group delay rises near the corner frequency.
Group delay is defined as the change in phase
(radians/second) divided by a change in frequency.
An increase in group delay corresponds to a time
domain pulse response that has overshoot and some
possible ringing associated with the overshoot.
30
The use of other type of filters, such as elliptic or
chebyshev, are not recommended for video
applications because of the very large group delay
variations near the corner frequency resulting in
significant overshoot and ringing. While these filters
may help meet the video standard specifications with
respect to amplitude attenuation, the group delay is
well beyond the standard specifications. Considering
this delay with the fact that video can go from a white
pixel to a black pixel over and over again, it is easy to
see that ringing can occur. Ringing typically causes a
display to have ghosting or fuzziness appear on the
edges of a sharp transition. On the other hand, a
Bessel filter has ideal group delay response, but the
rate of attenuation is typically too low for acceptable
image rejection. Thus, the Butterworth filter is a
respectable compromise for both attenuation and
group delay.
The THS7360 SD filters have a nominal corner
(–3-dB) frequency at 9.5 MHz and a –1-dB passband
typically at 8.2 MHz. This 9.5-MHz filter is ideal for
SD NTSC, PAL, and SECAM composite video
(CVBS) signals. It is also useful for S-Video signals
(Y’C’), 480i/576i Y’/P’B/P’R, Y’U’V’, broadcast G’B’R’
signals, and computer R'G'B' video signals. The
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS7360
THS7360
www.ti.com
SLOS674 – JUNE 2010
9.5-MHz, –3-dB corner frequency was designed to
achieve
54 dB of attenuation at 27 MHz—a common sampling
frequency between the DAC/ADC second and third
Nyquist zones found in many video systems. This
consideration is important because any signal that
appears around this frequency can also appear in the
baseband as a result of aliasing effects of an ADC
found in a receiver.
The THS7360 SF filters have a nominal corner
(–3 dB) frequency at 9.2 MHz, 17 MHz, 35 MHz, or
70 MHz and a –1-dB passband typically at 8 MHz, 15
MHz, 30 MHz, or 60 MHz. The 9.2-MHz filter is ideal
for component 480i or 576i video. The 17-MHz filter is
ideal for component 480p or 576p component video.
The 35-MHz filter is ideal for HD 720p, 1080i,
1080p24, or 1080p30 component video. The 70-MHz
filter is ideal for 1080p50 or 1080p60 component
video. These filters can also be utilized for some
computer R’G’B’ video signals including VGA, SVGA,
XGA, SXGA, and QXGA.
Keep in mind that images do not stop at the DAC
sampling frequency, fS (for example, 27 MHz for
traditional SD DACs); they continue around the
sampling frequencies of 2x fS, 3x fS, 4x fS, and so on
(that is, 54-MHz, 81-MHz, 108-MHz, etc.). Because of
these multiple images, an ADC can fold down into the
baseband signal, meaning that the low-pass filter
must also eliminate these higher-order images. The
THS7360 filters are Butterworth filters and, as such,
do not bounce at higher frequencies, thus maintaining
good attenuation performance.
The filter frequencies were chosen to account for
process variations in the THS7360. To ensure the
required video frequencies are effectively passed, the
filter corner frequency must be high enough to allow
component variations. The other consideration is that
the attenuation must be large enough to ensure the
anti-aliasing/reconstruction filtering is sufficient to
meet the system demands. Thus, the selection of the
filter frequencies was not arbitrarily selected and is a
good compromise that should meet the demands of
most systems.
One of the features of the THS7360 is that these
filters can be bypassed. Bypassing the SD filters
results in an amplifier with 60-MHz bandwidth and
150-V/ms slew rate. This configuration can be helpful
when diagnosing potential system issues or when
simply wishing to pass higher frequency signals
through the system.
Bypassing the SF filters results in a amplifier
supporting 280-MHz bandwidth and 800-V/ms slew
rate. This configuration supports computer R'G'B'
signals up to UWXGA resolution.
BENEFITS OVER PASSIVE FILTERING
Two key benefits of using an integrated filter system,
such as that found in the THS7360, over a passive
system are PCB area and filter variations. The small
TSSOP-20 package for six video channels is much
smaller over a passive RLC network, especially a
six-pole passive network. Additionally, consider that
inductors have at best ±10% tolerances (normally,
±15% to ±20% is common) and capacitors typically
have ±10% tolerances. A Monte Carlo analysis shows
that the filter corner frequency (–3 dB), flatness (–1
dB), Q factor (or peaking), and channel-to-channel
delay have wide variations. These variances can lead
to potential performance and quality issues in
mass-production environments. The THS7360 solves
most of these problems with the corner frequency
being essentially the only variable.
Another concern about passive filters is the use of
inductors. Inductors are magnetic components, and
are therefore susceptible to electromagnetic
coupling/interference (EMC/EMI). Some common
coupling can occur because of other video channels
nearby using inductors for filtering, or it can come
from nearby switched-mode power supplies. Some
other forms of coupling could be from outside sources
with strong EMI radiation and can cause failure in
EMC testing such as required for CE compliance.
One concern about an active filter in an integrated
circuit is the variation of the filter characteristics when
the ambient temperature and the subsequent die
temperature changes. To minimize temperature
effects, the THS7360 uses low-temperature
coefficient resistors and high-quality, low-temperature
coefficient capacitors found in the BiCom3X process.
These filters have been specified by design to
account for process variations and temperature
variations to maintain proper filter characteristics.
This approach maintains a low channel-to-channel
time delay that is required for proper video signal
performance.
Another benefit of the THS7360 over a passive RLC
filter is the input and output impedance. The input
impedance presented to the DAC varies significantly,
from 35 Ω to over 1.5 kΩ with a passive network, and
may cause voltage variations over frequency. The
THS7360 input impedance is 800 kΩ, and only the
2-pF input capacitance plus the PCB trace
capacitance impact the input impedance. As such,
the voltage variation appearing at the DAC output is
better controlled with a fixed termination resistor and
the high input impedance buffer of the THS7360.
On the output side of the filter, a passive filter again
has a large impedance variation over frequency. The
EIA/CEA770 specifications require the return loss to
be at least 25 dB over the video frequency range of
usage. For a video system, this requirement implies
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS7360
31
THS7360
SLOS674 – JUNE 2010
www.ti.com
the source impedance (which includes the source,
series resistor, and the filter) must be better than
75 Ω, +9/–8 Ω. The THS7360 is an operational
amplifier that approximates an ideal voltage source,
which is desirable because the output impedance is
very low and can source and sink current. To properly
match the transmission line characteristic impedance
of a video line, a 75-Ω series resistor is placed on the
output. To minimize reflections and to maintain a
good return loss meeting EIA/CEA specifications, this
output impedance must maintain a 75-Ω impedance.
A wide impedance variation of a passive filter cannot
ensure this level of performance. On the other hand,
the THS7360 has approximately 0.7 Ω of output
impedance, or a return loss of 46 dB, at 6.75 MHz for
the SD filters and approximately 1.7 Ω of output
impedance, or a return loss of 39 dB, at 30 MHz for
the SF-HD filters. Thus, the system is matched
significantly better with a THS7360 compared to a
passive filter.
One final benefit of the THS7360 over a passive filter
is power dissipation. A DAC driving a video line must
be able to drive a 37.5-Ω load: the receiver 75-Ω
resistor and the 75-Ω impedance matching resistor
next to the DAC to maintain the source impedance
32
requirement. This requirement forces the DAC to
drive at least 1.25 VP (100% saturation CVBS)/37.5 Ω
= 33.3 mA. A DAC is a current-steering element, and
this amount of current flows internally to the DAC
even if the output is 0 V. Thus, power dissipation in
the DAC may be very high, especially when six
channels are being driven. Using the THS7360 with a
high input impedance and the capability to drive up to
two video lines per channel can reduce DAC power
dissipation significantly. This outcome is possible
because the resistance that the DAC drives can be
substantially increased. It is common to set this
resistance in a DAC by a current-setting resistor on
the DAC itself. Thus, the resistance can be 300 Ω or
more, substantially reducing the current drive
demands from the DAC and saving significant
amounts of power. For example, a 3.3-V, six-channel
DAC dissipates 660 mW alone for the steering
current capability (six channels × 33.3 mA × 3.3 V) if
it must drive a 37.5-Ω load. With a 300-Ω load, the
DAC power dissipation as a result of current steering
current would only be 82 mW (six channels ×
4.16 mA × 3.3 V).
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS7360
THS7360
www.ti.com
SLOS674 – JUNE 2010
EVALUATION MODULE
To evaluate the THS7360, an evaluation module
(EVM) is available. The THS7360EVM allows for
testing the THS7360 in many different configurations.
Inputs and outputs include BNC connectors and RCA
connectors commonly found in video systems, along
with 75-Ω input termination resistors, 75-Ω series
source termination resistors, and 75-Ω characteristic
impedance traces. Several unpopulated component
pads are found on the EVM to allow for different input
and output configurations as dictated by the user.
This EVM is designed to be used with a single supply
from 2.6 V up to 5 V.
The EVM default input configuration sets all channels
for dc input coupling. The input signal must be within
0 V to approximately 0.65 V for proper operation.
Failure to be within this range saturates and/or clips
the output signal. If the input range is beyond this, if
the signal voltage is unknown, or if coming from a
current sink DAC, then ac input configuration is
desired. This option is easily accomplished with the
EVM by simply replacing the Z1 through Z6 0-Ω
resistors with 0.1-mF capacitors.
For an ac-coupled input and sync-tip clamp (STC)
functionality commonly used for CVBS, s-video Y',
component Y' signals, and R'G'B' signals, no other
changes are needed. However, if a bias voltage is
needed after the input capacitor which is commonly
needed for s-video C', component P'B, and P'R, then a
pull-up resistor should be added to the signal on the
EVM. This configuration is easily achieved by simply
adding a resistor to any of the following resistor pads;
RX7 to RX12. A common value to use is 10 MΩ.
Note that even signals with embedded sync can also
use bias mode if desired.
The EVM default output configuration sets all
channels for ac output coupling. The 470-mF and
0.1-mF capacitors work well for most ac-coupled
systems. However, if dc-coupled output is desired,
then replacing the 0.1-mF capacitors (C20, C22, C24,
C26, C28, and/or C30) with 0-Ω resistors works well.
Removing the 470-mF capacitors is optional, but
removing them from the EVM eliminates a few
picofarads of stray capacitance on each signal path
which may be desirable.
The THS7360 incorporates an easy method to
configure the bypass modes and the disable modes.
The use of JP4 controls the SD channels disable
feature; JP6 controls the SF channels disable feature;
JP3 controls the SD channels filter/bypass mode; and
JP5 controls the SF channels filter/bypass mode.
Connection of JP4 and JP6 to GND applies 0 V to the
disable pins and the THS7360 operates normally.
Moving JP4 to +VS causes the THS7360 SD
channels to be in disable mode, while moving JP6 to
+VS causes the THS7360 SF channels to be in
disable mode.
Connection of JP3 to GND places the THS7360 SD
channels in filter mode while moving JP3 to +VS
places the THS7360 SD channels in bypass mode.
Connection of JP5 to GND places the THS7360 SF
channels in filter mode while moving JP5 to +VS
places the THS7360 SF channels in bypass mode.
The filter selection is also easily accomplished by
using jumpers JP1 and JP2. JP1 controls the logic
voltage for the filter 1 pin while JP2 controls the logic
voltage for the filter 2 pin. Table 1 and Table 2 show
the truth table for the filter selection and the
appropriate logic for 3.3-V and 5-V operation,
respectively. The EVM also has a truth table printed
on it for easy reference.
Figure 49 shows the THS7360EVM schematic.
Figure 51 and Figure 52 illustrate the two layers of
the EVM PCB, incorporating standard high-speed
layout practices. Table 7 lists the bill of materials as
the board comes supplied from Texas Instruments.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS7360
33
THS7360
www.ti.com
+
+
SLOS674 – JUNE 2010
Figure 49. THS7360 EVM Schematic
34
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS7360
THS7360
www.ti.com
SLOS674 – JUNE 2010
+
+
+
+
+
+
Figure 50. THS7360 EVM Schematic
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS7360
35
THS7360
SLOS674 – JUNE 2010
www.ti.com
Figure 51. THS7360 EVM PCB Top Layer
36
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS7360
THS7360
www.ti.com
SLOS674 – JUNE 2010
Figure 52. THS7360 EVM PCB Bottom Layer
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS7360
37
THS7360
SLOS674 – JUNE 2010
www.ti.com
THS7360EVM Bill of Materials
Table 7. THS7360 EVM
38
ITEM
REF DES
QTY
DESCRIPTION
SMD SIZE
1
FB1, FB2
2
Bead, ferrite, 2.5 A, 330 Ω
2
C12
1
Capacitor, 100 µF, tantalum, 10 V, 10%, low
ESR
3
C40
1
Capacitor, 22 µF, tantalum, 16 V, 10%, low
ESR
4
C1-C6,
C13-C18,
C31-C36
18
Open
0805
5
C37
1
Capacitor, 0.01 µF, ceramic, 100 V, X7R
6
C8, C10, C11,
C20, C22, C24,
C26, C28, C30,
C38, C39,
C41-C52
23
7
C9
8
9
MANUFACTURER
PART NUMBER
DISTRIBUTOR
PART NUMBER
(TDK) MPZ2012S331A
(DIGI-KEY)
445-1569-1-ND
C
(AVX) TPSC107K010R0100
(DIGI-KEY)
478-1765-1-ND
C
(AVX) TPSC226K016R0375
(DIGI-KEY)
478-1767-1-ND
0805
(AVX) 08051C103KAT2A
(DIGI-KEY)
478-1358-1-ND
Capacitor, 0.1 µF, ceramic, 50 V, X7R
0805
(AVX) 08055C104KAT2A
(DIGI-KEY)
478-1395-1-ND
1
Capacitor, 0.1 µF, ceramic, 50 V, X7R
1206
(AVX) 12065C104KAT2A
(DIGI-KEY)
478-1556-1-ND
C7
1
Capacitor, 3.3 µF, ceramic, 25 V, X7R
1206
(TDK) C3216X7R1E335K
(DIGI-KEY)
PCE4526CT-ND
C19, C21, C23,
C25, C27, C29
6
Capacitor, aluminum, 470 µF, 10 V, 20%
10
RX1-RX12
12
Open
0603
11
Z1-R9, R7-R9,
R19-R21,
R26-R28,
R35-R37
18
Resistor, 0 Ω
0805
(ROHM) MCR10EZHJ000
(DIGI-KEY)
RHM0.0ACT-ND
12
R1-R6,
R29-R34
12
Resistor, 75 Ω, 1/8W, 1%
0805
(ROHM) MCR10EZHF75.0
(DIGI-KEY)
RHM75.0CCT-ND
13
R14
1
Resistor, 100 Ω, 1/8W, 1%
0805
(ROHM) MCR10EZHF1000
(DIGI-KEY)
RHM100CCT-ND
14
R10, R11, R15,
R17, R24, R25
6
Resistor, 1k Ω, 1/8W, 1%
0805
(ROHM) MCR10EZHF1001
(DIGI-KEY)
RHM1.00KCCT-ND
15
R12, R13, R16,
R18, R22, R23
6
Resistor, 100k Ω, 1/8W, 1%
0805
(ROHM) MCR10EZHF1003
(DIGI-KEY)
RHM100KCCT-ND
16
R38
1
Resistor, 1k Ω, 1/4W, 1%
1206
(ROHM) MCR18EZHF1001
(DIGI-KEY)
RHM1.00KFCT-ND
17
D1-D12
12
Diode, ultrafast
(FAIRCHILD) BAV99
(DIGI-KEY)
BAV99FSCT-ND
18
J10, J11
2
Jack, banana receptance, 0.25" diameter
hole
(SPC) 15459
(NEWARK) 79K5034
19
J1-J6, J13-J18
12
Connector, BNC, jack, 75 Ω
(AMPHENOL)
31-5329-72RFX
(NEWARK) 93F7554
20
J8, J20
2
Connector, mini circular DIN
(CUI) MD-40SM
(DIGI-KEY) CP-2240-ND
21
J7, J19
2
Connector, RCA jack, yellow
(CUI) RCJ-044
(DIGI-KEY) CP-1421-ND
22
J9, J12
2
Connector, RCA, jack, R/A
(CUI) RCJ-32265
(DIGI-KEY) CP-1446-ND
23
TP1, TP2
2
Test point, black
(KEYSTONE) 5001
(DIGI-KEY) 5001K-ND
24
JP1-JP6
6
Header, 0.1" CTRS, 0.025" square pins
(SULLINS) PBC36SAAN
(DIGI-KEY) S1011E-36-ND
25
JP1-JP6
6
Shunts
(SULLINS) SSC02SYAN
(DIGI-KEY) S9002-ND
26
U1
1
IC, THS7360
27
—
4
Standoff, 4-40 hex, 0.625" length
(KEYSTONE) 1808
(DIGI-KEY) 1808K-ND
28
—
4
Screw, Phillips, 4-40, .250"
PMSSS 440 0025 PH
(DIGI-KEY) H703-ND
—
1
Board, printed circuit
Edge # 6510793 Rev. A
805
F
3 pos.
PW
Submit Documentation Feedback
(PANASONIC)
EEE-FP1A471AP
(TI) THS7360IPW
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS7360
THS7360
www.ti.com
SLOS674 – JUNE 2010
EVALUATION BOARD/KIT IMPORTANT NOTICE
Texas Instruments (TI) provides the enclosed product(s) under the following conditions:
This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES
ONLY and is not considered by TI to be a finished end-product fit for general consumer use. Persons handling the product(s) must have
electronics training and observe good engineering practice standards. As such, the goods being provided are not intended to be complete
in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including product safety and environmental
measures typically found in end products that incorporate such semiconductor components or circuit boards. This evaluation board/kit does
not fall within the scope of the European Union directives regarding electromagnetic compatibility, restricted substances (RoHS), recycling
(WEEE), FCC, CE or UL, and therefore may not meet the technical requirements of these directives or other related directives.
Should this evaluation board/kit not meet the specifications indicated in the User’s Guide, the board/kit may be returned within 30 days from
the date of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY SELLER TO BUYER
AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies TI from all claims
arising from the handling or use of the goods. Due to the open construction of the product, it is the user’s responsibility to take any and all
appropriate precautions with regard to electrostatic discharge.
EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY
INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
TI currently deals with a variety of customers for products, and therefore our arrangement with the user is not exclusive.
TI assumes no liability for applications assistance, customer product design, software performance, or infringement of patents or
services described herein.
Please read the User’s Guide and, specifically, the Warnings and Restrictions notice in the User’s Guide prior to handling the product. This
notice contains important safety information about temperatures and voltages. For additional information on TI’s environmental and/or
safety programs, please contact the TI application engineer or visit www.ti.com/esh.
No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine, process, or
combination in which such TI products or services might be or are used.
FCC Warning
This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES
ONLY and is not considered by TI to be a finished end-product fit for general consumer use. It generates, uses, and can radiate radio
frequency energy and has not been tested for compliance with the limits of computing devices pursuant to part 15 of FCC rules, which are
designed to provide reasonable protection against radio frequency interference. Operation of this equipment in other environments may
cause interference with radio communications, in which case the user at his own expense will be required to take whatever measures may
be required to correct this interference.
EVM WARNINGS AND RESTRICTIONS
It is important to operate this EVM within the input voltage range of 2.6 V to 5.5 V single-supply and the output voltage range of 0 V to
5.5 V.
Exceeding the specified input range may cause unexpected operation and/or irreversible damage to the EVM. If there are questions
concerning the input range, please contact a TI field representative prior to connecting the input power.
Applying loads outside of the specified output range may result in unintended operation and/or possible permanent damage to the EVM.
Please consult the EVM User's Guide prior to connecting any load to the EVM output. If there is uncertainty as to the load specification,
please contact a TI field representative.
During normal operation, some circuit components may have case temperatures greater than +85°C. The EVM is designed to operate
properly with certain components above +85°C as long as the input and output ranges are maintained. These components include but are
not limited to linear regulators, switching transistors, pass transistors, and current sense resistors. These types of devices can be identified
using the EVM schematic located in the EVM User's Guide. When placing measurement probes near these devices during operation,
please be aware that these devices may be very warm to the touch.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS7360
39
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
(3)
(4)
THS7360IPW
ACTIVE
TSSOP
PW
20
70
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
THS7360
THS7360IPWR
ACTIVE
TSSOP
PW
20
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
THS7360
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a
continuation of the previous line and the two combined represent the entire Top-Side Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
Samples
PACKAGE MATERIALS INFORMATION
www.ti.com
24-Jan-2014
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
THS7360IPWR
Package Package Pins
Type Drawing
TSSOP
PW
20
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
2000
330.0
16.4
Pack Materials-Page 1
6.95
B0
(mm)
K0
(mm)
P1
(mm)
7.1
1.6
8.0
W
Pin1
(mm) Quadrant
16.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
24-Jan-2014
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
THS7360IPWR
TSSOP
PW
20
2000
367.0
367.0
38.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated