OPA360

OPA360
SB0S294E − DECEMBER 2003 − REVISED SEPTEMBER 2006
3V Video Amplifier
with 6dB Gain and Filter in SC70
FEATURES
DESCRIPTION
D
D
D
D
The OPA360 high-speed amplifier is optimized for 3V
portable video applications. It has been specifically
designed to be compatible with digital-to-analog
converters (DACs) embedded in video processors, such
as Texas Instruments’ family of Digital Media Processors
and others. The input common-mode range includes
GND, which allows the Video-DAC to be DC-coupled to
the OPA360.
EXCELLENT VIDEO PERFORMANCE
INTERNAL GAIN: 6dB
2-POLE RECONSTRUCTION FILTER
SAG CORRECTION
− Reduces Coupling Capacitor Size
D INPUT RANGE INCLUDES GROUND
The output swings within 25mV of GND and 300mV to V+
with a standard back-terminated video load (150Ω). An
internal level shift circuit prevents the output from
saturating with 0V input, thus preventing sync-pulse
clipping in common video circuits. Therefore, the OPA360
is ideally suited for DC-coupling to the video load. If
AC-coupling is preferred, the OPA360 offers a
sag-correction feature that significantly reduces the size of
the output coupling capacitor.
− DC-Coupled Input
D INTEGRATED LEVEL SHIFTER
− DC-Coupled Output(1)
− No Output Capacitors Needed
D
D
D
D
D
RAIL-TO-RAIL OUTPUT
LOW QUIESCENT CURRENT: 6mA
SHUTDOWN CURRENT: 5mA (max)
SINGLE-SUPPLY: 2.7V to 3.3V
SC70-6 PACKAGE: 2.0mm x 2.1mm
(1) Internal circuitry prevents the output from saturating, even with 0V sync
tip level at the input video signal.
APPLICATIONS
The OPA360 has been optimized for space-sensitive
applications by integrating sag-correction, internal gain
setting resistors (G = 2), and a 2-pole video-DAC
reconstruction filter.
In shutdown mode, the quiescent current is reduced to
< 5µA, dramatically reducing power consumption and
prolonging battery life.
The OPA360 is available in the tiny 2mm x 2.1mm SC70-6
package.
D DIGITAL CAMERAS
D CAMERA PHONES
D SET-TOP-BOX VIDEO FILTERS
V+ = 2.7V
to 3.3V ENABLE
RELATED LOW VOLTAGE VIDEO AMPS
V+
OPA360
FEATURES
PRODUCT
2.7V to 5.5V, 200MHz GBW, 300V/µs, 6µA Sleep, SOT23
OPA355
2.7V to 5.5V, RRIO, 150V/µs, 5mA IQ, 6µA Sleep, SOT23
OPA357
2.7V to 3.3V, SC70, 80MHz, 7.5mA IQ, 5µA Sleep
OPA358
2.5V to 3.3V, SC70, Filter, G = 5.2V/V, 3µA Sleep
OPA361
VIN
Level
Shifter
Enable
2−Pole
Filter
VO
6dB
SAG
GND
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments
semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
Copyright  2003−2006, Texas Instruments Incorporated
! ! www.ti.com
"#$
www.ti.com
SB0S294E − DECEMBER 2003 − REVISED SEPTEMBER 2006
ORDERING INFORMATION(1)
PRODUCT
PACKAGE
PACKAGE DESIGNATOR
OPA360
SC70-6
DCK
PACKAGE MARKING
AUW
(1) For the most current package and ordering information see the Package Option Addendum at at the end of this document, or see the TI web
site at www.ti.com.
This integrated circuit can be damaged by ESD. Texas
Instruments recommends that all integrated circuits be
handled with appropriate precautions. Failure to observe
proper handling and installation procedures can cause damage.
ABSOLUTE MAXIMUM RATINGS(1)
Supply Voltage, V+ to V− . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +3.6V
Signal Input Terminals, Voltage(2) . . . . (V−) −0.5V to (V+) + 0.5V
Current(2) . . . . . . . . . . . . . . . . . . . ±10mA
Output Short-Circuit through 75Ω to GND(3) . . . . . . . Continuous
ESD damage can range from subtle performance degradation to
complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could
cause the device not to meet its published specifications.
Operating Temperature . . . . . . . . . . . . . . . . . . . . . . −40°C to +85°C
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . −65°C to +150°C
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +160°C
(1) Stresses above these ratings may cause permanent damage.
Exposure to absolute maximum conditions for extended periods
may degrade device reliability. These are stress ratings only, and
functional operation of the device at these or any other conditions
beyond those specified is not implied.
(2) Input terminals are diode-clamped to the power-supply rails.
Input signals that can swing more than 0.5V beyond the supply
rails should be current-limited to 10mA or less.
(3) Short-circuit to ground.
PIN CONFIGURATION
OPA360
1
GND
2
SAG
3
LPF
AUW
+In
SC70−6(1)
(1) Pin 1 of the SC70-6 is determined by orienting
the package marking as indicated in the diagram.
2
6
V+
5
Enable
4
Out
"#$
www.ti.com
SB0S294E − DECEMBER 2003 − REVISED SEPTEMBER 2006
ELECTRICAL CHARACTERISTICS: VS = +2.7V to +3.3V Single-Supply
Boldface limits apply over the temperature range, TA = −40°C to +85°C.
All specifications at TA = +25°C, RL = 150Ω connected to GND, unless otherwise noted.
OPA360
PARAMETER
OFFSET LEVEL-SHIFT VOLTAGE
Output Level-Shift Voltage(1)
VOLS
Over Temperature
vs. Power Supply
PSRR
CONDITIONS
MIN
TYP
MAX
VS = +3.3V, VIN = GND, G = +2
Specified Temperature Range
30
60
80
VS = +2.7V to +3.3V
UNITS
mV
60
mV
±80
µV/V
±3
pA
INPUT BIAS CURRENT
Input Bias Current
IB
INPUT VOLTAGE RANGE
Common-Mode Voltage Range(2)
VCM
VS = 3.3V, G = +2
GND
(V+) − 1.5
V
VS = +3.3V, 0 < VIN < 1.5V
5.8
6
6.2
dB
VO = 2VPP
VO = 2VPP
−0.6
−0.1
+0.4
dB
−18
−21
dB
0.5
%
Differential Phase Error
RL = 150Ω
RL = 150Ω
1
°
Group Delay Variation
100kHz, 5MHz
13
ns
100% White Signal
70
dB
VS = +3.3V, G = 2, VIN = 2V, RL = 150Ω to GND
VS = +3.3V, G = 2, VIN = 0V, RL = 150Ω to GND
160
300
mV
3
25
mV
VS = +3.3V, G = 2, VIN = 2V, RL = 75Ω to GND
VS = +3.3V, G = 2, VIN = 0V, RL = 75Ω to GND
300
mV
10
mV
VS = +3.3V
±80
mA
VOLTAGE GAIN
FREQUENCY RESPONSE
Filter Response
Normalized Gain: fIN = 4.5MHz
fIN = 27MHz
Differential Gain Error
Signal-to-Noise Ratio
SNR
OUTPUT
Positive Voltage Output Swing from Rail
Negative Voltage Output Swing from Rail
Positive Voltage Output Swing from Rail
Negative Voltage Output Swing from Rail
Output Current(3)
IO
POWER SUPPLY
Specified Voltage Range
VS
2.7
Minimum Operating Voltage Range
Quiescent Current
3.3
V
7.5
mA
9
mA
0.8
V
2.5 to 3.6
IQ
VS = +3.3V, Enabled, IO = 0
Specified Temperature Range
6
V
ENABLE/SHUTDOWN FUNCTION
Disabled (logic-LOW Threshold)
Enabled (logic-HIGH Threshold)
1.6
Enable Time
V
µs
1.5
Disable Time
50
Shutdown Current
VS = +3.3, Disabled
2.5
ns
5
µA
TEMPERATURE RANGE
Specified Range
−40
+85
°C
Operating Range
−40
+85
°C
Storage Range
−65
+150
°C
Thermal Resistance
qJA
SC70
250
°C/W
(1) Output referred. Tested with SAG pin connected to OUT pin.
(2) Limited by output swing and internal G = 2. Tested with the SAG pin connected to OUT pin.
(3) See typical characteristics Output Voltage Swing vs Output Current.
3
"#$
www.ti.com
SB0S294E − DECEMBER 2003 − REVISED SEPTEMBER 2006
TYPICAL CHARACTERISTICS: VS = 3.3V
At TA = +25°C and RL = 150Ω, unless otherwise noted.
Normalized Gain at 4.5MHz
Production Distribution
FREQUENCY RESPONSE
5
Normalized:
”0” dB corresponds
to 6dB gain.
−5
−10
Population
Normalized Gain (dB)
0
−15
−20
−25
−30
−35
−0.125
100M
0.05
0.075
0.1
10M
−0.05
−0.025
0
0.025
1M
Frequency (Hz)
−0.225
−0.2
−0.175
−0.15
−0.125
−0.1
−0.075
100k
−0.325
10k
−0.3
−0.275
−0.25
−40
Normalized Gain at 4.5MHz (dB)
GAIN ERROR
2.0
40
1.8
35
1.6
30
Gain Error (%)
Group Delay (ns)
GROUP DELAY vs FREQUENCY
45
25
20
15
1.0
0.8
0.6
0.4
5
0.2
0
10k
100k
1M
10M
−50
−25
0
25
50
75
100
125
Frequency (Hz)
Temperature (_C)
OUTPUT VOLTAGE SWING TO THE POSITIVE RAIL
vs OUTPUT CURRENT
OUTPUT VOLTAGE SWING TO THE NEGATIVE RAIL
vs OUTPUT CURRENT
3.3
3.2
3.1
3.0
2.9
2.8
2.7
2.6
2.5
2.4
2.3
2.2
2.1
2.0
0.30
VS = 3.3V
VS = 3.3V, VIN = 0V
0.25
−40_ C
+25_C
+85_ C
Output Voltage (V)
Output Voltage (V)
1.2
10
0
+85_C
0.20
0.15
+25_ C
−40_C
0.10
0.05
0
0
0.01 0.02 0.03 0.04 0.05 0.06 0.07 0.08 0.09 0.1
Output Current (A)
4
1.4
0
0.01 0.02 0.03 0.04 0.05 0.06 0.07 0.08 0.09 0.1
Output Current (A)
"#$
www.ti.com
SB0S294E − DECEMBER 2003 − REVISED SEPTEMBER 2006
TYPICAL CHARACTERISTICS: VS = 3.3V (continued)
At TA = +25°C and RL = 150Ω, unless otherwise noted.
QUIESCENT CURRENT vs TEMPERATURE
8.0
6
7.5
VS = 3.3V
Quiescent Current (mA)
Quiescent Current (mA)
QUIESCENT CURRENT vs SUPPLY VOLTAGE
7
5
4
3
2
7.0
6.5
6.0
5.5
1
0
5.0
−50
2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3
−25
0
25
Supply Voltage (V)
50
75
100
125
Temperature (_C)
SHUTDOWN CURRENT vs TEMPERATURE
DIFFERENTIAL GAIN
3.0
Shutdown Current (µA)
2.5
DIFFERENTIAL PHASE
VS = 3.3V
2.0
1.5
1.0
0.5
0
−50
−25
0
25
50
75
100
125
Temperature (_ C)
SHUTDOWN TRIGGER LEVELS
LARGE−SIGNAL DISABLE/ENABLE RESPONSE
Enable
Voltage (500mV/div)
Quiescent Current (mA)
6
4
OPA360
Shutdown
OPA360
Active
2
OPA360
Output
Disable
0
1.4
1.45
1.5
1.55
1.6
Time (1µs/div)
Enable Pin Voltage (V)
5
"#$
www.ti.com
SB0S294E − DECEMBER 2003 − REVISED SEPTEMBER 2006
APPLICATIONS INFORMATION
The OPA360 video amplifier has been optimized for
portable video applications:
D Internal gain setting resistors (G = 2) reduce the
number of external components needed in the
video circuit.
D A 2-pole filter is incorporated for DAC signal
reconstruction.
D The sag correction function reduces the size of the
output coupling capacitors without compromising
performance.
D OPA360 employs an internal level shift circuit that
avoids sync pulse clipping and allows DC-coupled
output.
D A shutdown feature reduces quiescent current to
less than 5µA—crucial for portable applications
such as digital still cameras (DSCs) and camera
phones.
The OPA360 interfaces to digital media processors
(DM320/270, DSC25). It has been optimized for the
requirements of digital still cameras and cell
phone/camera designs.
OPERATING VOLTAGE
The OPA360 is fully specified from 2.7V to 3.3V over a
temperature range of −40°C to +85°C. Parameters that
vary significantly with operating voltages or temperature
are shown in the Typical Characteristics.
Power-supply pins should be bypassed with 100nF
ceramic capacitors.
INPUT VOLTAGE
The input common-mode range of the OPA360 series
extends from GND to (V+) − 1.5V. Because of the internal
gain, the input voltage range necessary for an output in the
valid range will be limited.
INPUT OVERVOLTAGE PROTECTION
All OPA360 pins are static-protected with internal ESD
protection diodes connected to the supplies. These diodes
will provide input overdrive protection if the current is
externally limited to 10mA
ENABLE/SHUTDOWN
The OPA360 has a shutdown feature that disables the
output and reduces the quiescent current to less than 5µA.
This feature is especially useful for portable video
applications such as digital still cameras and camera
phones, where the equipment is infrequently connected to
a TV or other video device.
The Enable logic input voltage is referenced to the
OPA360 GND pin. A logic level HIGH applied to the enable
pin enables the op amp. A valid logic HIGH is defined as
≥ 1.6V above GND. A valid logic LOW is defined as ≤ 0.8V
above GND. If the Enable pin is not connected, internal
pull-up circuitry will enable the amplifier. Enable pin
voltage levels are tested for a valid logic HIGH threshold
of 1.6V minimum and a valid logic LOW threshold of 0.8V
maximum.
INTERNAL 2-POLE FILTER
The OPA360 filter is a Sallen-Key topology with a 9MHz
cutoff frequency. This allows the video signals to pass
without any visible distortion, as shown in Figure 3 through
Figure 5. The video DACs embedded in TI’s Digital Media
Processors over-sample at 27MHz. At this frequency, the
attenuation is typically 21dB, which effectively attenuates
the sampling aliases.
The filter characteristics vary somewhat with signal source
impedance. A source impedance greater than 500Ω can
degrade filter performance. With current-output video
DACs, a resistor to GND is often used to create a voltage
output which is then applied to the OPA360 input (see
Figure 1). TI’s Digital Media Processors, such as the
DM270 or DM320, typically use a 200Ω resistor to GND to
convert the current output signal. This 200Ω source
impedance does not degrade video performance.
10pF
1.1kΩ
(
Television
1.4kΩ
)
VO
(1)
75Ω
12pF
R
845Ω
325Ω
NOTE: (1) Optional.
528Ω
75Ω
SAG
650Ω
OPA360
Figure 1. Filter Structure of OPA360
6
"#$
www.ti.com
SB0S294E − DECEMBER 2003 − REVISED SEPTEMBER 2006
A capacitor placed in parallel with the resistor (Figure 1)
creates an additional filter pole that provides additional
stop-band attenuation. With a 200Ω source impedance, a
67pF ceramic capacitor provides approximately 28dB
attenuation at 27MHz without affecting the pass band.
VIDEO PERFORMANCE
of amplitude and group delay errors across the video
baseband.
D
Chrominance-to-luminence (CCIR17) — tests amplitude, phase and some distortion
D
50Hz, 1/2 black−1/2 white screen test signal—tests
the worst case signal swing required by the amplifier.
Performance on these test signals are shown.
Industry standard video test patterns include:
D
Multiburst—packets of different test frequencies to
check for basic frequency response.
D
Multipulse—pulses
modulated
at
different
frequencies to test for comprehensive measurement
Figure 2 shows the test circuits for Figure 3 through
Figure 13 and Figure 16. (NOTE: 1 and 2 indicate
measurement points corresponding to the waveforms
labeled 1 and 2 in the figures.)
2
1
2
1
47µF
22µF
SAG
a. Test circuit for Figures 3−5.
b. Test circuit for Figures 6, 8, and 16.
1
1
2
1
2
COUT
220µF
22µF
22µF
c. Test circuits for Figures 10 and 11.
d. Test circuit for Figures 7, 12, and 13.
NOTE: 1 and 2 indicate measurement points corresponding to the waveforms labeled 1 and 2 in the figures.
Figure 2. Test Circuits Used for Figures 3−13
7
"#$
www.ti.com
SB0S294E − DECEMBER 2003 − REVISED SEPTEMBER 2006
FREQUENCY RESPONSE OF THE OPA360
Frequency response measurements evaluate the ability of
a video system to uniformly transfer signal components of
different frequencies without affecting their respective
amplitudes. Figure 3 shows the multiburst test pattern;
Figure 4 shows the multipulse. The top waveforms in
these figures show the full test pattern. The middle and
bottom waveform are a more detailed view of the critical
portion of the full waveform. The middle waveform
represents the input signal from the video generator; the
bottom waveform is the OPA360 output to the line.
Chrominance-to-luminence gain inequality (or relative
chrominance level) is a change in the gain ratio of the
chrominance and luminence components of a video
signal, which are at different frequencies. A common test
pattern is the pulse in test pattern CCIR 17, shown in
Figure 5. As in Figure 3 and Figure 4, the top waveform
shows the full test pattern; the middle and bottom
waveform are a more detailed view of the critical portion of
the full waveform, with the middle waveform representing
the input signal from the video generator and the bottom
waveform being the OPA360 output to the line.
Figure 3. Multiburst (CCIR 18) Test Pattern (PAL)
Figure 5. CCIR 17 Test Pattern (PAL)
Gain errors most commonly appear as attenuation or
peaking of the chrominance information. This shows up in
the picture as incorrect color saturation. Delay distortion
will cause color smearing or bleeding, particularly at the
edges of objects in the picture. It may also cause poor
reproduction of sharp luminence transitions.
All waveforms in Figure 3 through Figure 5 were taken
using the sag correction feature of OPA360. Figure 3
through Figure 5 show that the OPA360 causes no visible
distortion or change in gain throughout the entire video
frequency range.
INTERNAL LEVEL SHIFT
Figure 4. Multipulse Test Pattern (PAL)
8
Many common video DACs embedded in digital media
processors like TI’s TMS320DM270 and the new
OMAP2420 processors operate on a single supply (no
negative supply). Typically, the lowest point of the sync
pulse output by these Video DACs corresponds to 0V. With
a 0V input, the output of common single-supply op amps
saturates at a voltage > 0V. This effect would clip the tip of
the sync pulse and therefore degrade the video signal
integrity. The OPA360 employs an internal level shift circuit
to avoid clipping. The input signal is typically shifted by
"#$
www.ti.com
SB0S294E − DECEMBER 2003 − REVISED SEPTEMBER 2006
approximately 60mV. This is well within the linear output
voltage range of the OPA360 with a standard 150Ω video
load. Figure 6 shows the function of the level shifter.
Figure 7. Output Swing with 33mF on 3V Supply
OUTPUT SWING TO GND (SYNC PULSE)
Figure 6. Internal Level Shifter, Shifts Input
Signal by Approximately 60mV to Prevent Sync
Tip Clipping
Figure 8 shows the true output swing capability of the
OPA360 by taking the tip of the input sync pulse to a
slightly negative voltage. Even when the output sync tip is
at 8mV, the output shows no clipping of the sync pulse.
The level shift function is particularly useful when the
output of the OPA360 is DC-coupled to the video load.
However, it is also helpful when sag correction is
employed. The offset helps to shift the video signal closer
to the positive rail, so that with even a small 33µF coupling
capacitor, the output is well outside the saturation limits of
the OPA360. Figure 7 shows the output swing of the
OPA360, operated on 3.0V supplies, with a 22µF sag
correction capacitor and a 33µF output coupling capacitor.
The test signal is a 50Hz signal constructed to generate a
1/2 black, 1/2 white screen. This video pattern is one of the
most difficult patterns to display because it is the worst
case signal regarding signal swing. A worst case signal
such as this is highly unlikely in normal operation. Any
other signal has a lower swing range. Note in Figure 7 that
neither the white nor the black portion of the video signal
is clipped.
Figure 8. Input Sync Tip at −30mV (Output Shows
No Sign of Clipping)
9
"#$
www.ti.com
SB0S294E − DECEMBER 2003 − REVISED SEPTEMBER 2006
SAG CORRECTION
Sag correction provides excellent video performance with
two small output coupling capacitors. It eliminates the
traditional, large 220µF output capacitor. The traditional
220µF circuit (Figure 9a) creates a single low frequency
pole (−3dB frequency) at 5Hz. If this capacitor is made
much smaller, excessive phase shift in the critical 50 to
100Hz range produces field tilt which can interfere with
proper recovery of synchronization signals in the television
receiver.
The OPA360 sag correction circuit (Figure 9b, see also
Figure 14) creates an amplitude response peak in the
20Hz region. This small amount of peaking (a few tenths
of a dB) provides compensation of the phase response in
the critical 50Hz to 100Hz range, greatly reducing field tilt.
Note that two significantly smaller and lower cost
capacitors are required.
220µF 75Ω
Figure 10. Standard Video Circuit with 220mF
Capacitor (top trace) vs OPA360 with 22mF and
47mF Capacitors
75Ω
A field tilt equivalent to that achieved using the standard
220µF coupling capacitor can be achieved with a
22µF/67µF combination − see Figure 11. These capacitor
values are optimized—sag correction capacitors larger
than 22µF do not provide significant improvement. Smaller
sag correction capacitors will lead to higher tilt.
a) Traditional Video Circuit
47µF
22µF
75Ω
75Ω
b) OPA360 with Sag Correction
Figure 9. Traditional Video Circuit vs OPA360
with Sag Correction
To achieve good performance, a 22µF sag correction and
47µF coupling capacitor can be used. Figure 10 and
Figure 11 show comparisons for a standard video circuit
with a 220µF coupling capacitor and the OPA360 with sag
correction.
Figure 10 shows that the 22µF/47µF combination leads to
only a slightly greater tilt in the 50Hz, 1/2 black − 1/2 white
video signal. No degradation in video quality is observed.
10
Figure 11. 220mF Standard Video Circuit (top
trace) vs OPA360 with 22mF and 67mF Capacitors
"#$
www.ti.com
SB0S294E − DECEMBER 2003 − REVISED SEPTEMBER 2006
SUPPLY VOLTAGE vs COUPLING CAPACITOR
The output voltage swing is a function of the coupling
capacitor value. The value of the sag correction capacitor
has only a minor influence. The smaller the coupling
capacitor, the greater the output swing. Therefore, to
accommodate the large signal swing with very small
coupling capacitors (22µF and 33µF), a higher supply
voltage might be needed.
As seen in Figure 7, the output swing with a 33µF coupling
capacitor is already very close to the saturation limit on a
3V supply. Over time and temperature, a capacitor might
change its value slightly, which in turn could force the
output into saturation. Using the 50Hz, 1/2 blackĊ1/2
white screen test signal as a worst-case analysis,
Figure 12 and Figure 13 demonstrate that a 3V supply
could be used with a coupling capacitor as low as 47µF.
Figure 12. Output Swing with 47mF on 3V Supply
Figure 13. Output Swing with 67mF on 3V Supply
V+ = 2.7V to 3.3V
ENABLE
V+
OPA360
Video
DAC
(1)
Level
Shifter
2−Pole
Filter
Enable
OUT
COUT
47µF
+
ROUT
75Ω
CSAG
22µF
+
75Ω
SAG
AC Gain = 2
DC Gain = 2.8
Television
or VCR
GND
NOTE: (1) Optional 200Ω for use with TI’s Digital Media Processors.
Figure 14. DC-Coupled Input/AC-Coupled Output
11
"#$
www.ti.com
SB0S294E − DECEMBER 2003 − REVISED SEPTEMBER 2006
DC-COUPLED OUTPUT
The DC-coupled output configuration also shows the best
video performance. As seen in Figure 16, there is no line
or field tilt—allowing use of the lowest power supply. In this
mode, the OPA360 will safely operate down to 2.5V with
no clipping of the signal.
The disadvantage with DC-coupled output is that it uses
somewhat higher supply current.
Due to the internal level shift, the OPA360 can also be DCcoupled to a video load. As shown in Figure 15, this
eliminates the need for AC-coupling capacitors at the
output. This is especially important in portable video
applications where board space is restricted.
V+ = 2.7V to 3.3V
ENABLE
V+
OPA360
Video
DAC
(1)
Level
Shifter
2−Pole
Filter
Enable
OUT
ROUT
75Ω
75Ω
6dB
SAG
GND
NOTE: (1) Optional 200Ω for use with TI’s Digital Media Processors.
Figure 15. DC-Coupled Input/DC-Coupled Output
Figure 16. DC-Coupled Output
12
Television
or VCR
PACKAGE OPTION ADDENDUM
www.ti.com
12-Sep-2006
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
OPA360AIDCKR
ACTIVE
SC70
DCK
6
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA360AIDCKRE4
ACTIVE
SC70
DCK
6
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA360AIDCKT
ACTIVE
SC70
DCK
6
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA360AIDCKTG4
ACTIVE
SC70
DCK
6
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Jan-2009
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
Diameter Width
(mm) W1 (mm)
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
W
Pin1
(mm) Quadrant
OPA360AIDCKR
SC70
DCK
6
3000
179.0
8.4
2.2
2.5
1.2
4.0
8.0
Q3
OPA360AIDCKT
SC70
DCK
6
250
179.0
8.4
2.25
2.4
1.22
4.0
8.0
Q3
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Jan-2009
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
OPA360AIDCKR
SC70
DCK
6
3000
195.0
200.0
45.0
OPA360AIDCKT
SC70
DCK
6
250
195.0
200.0
45.0
Pack Materials-Page 2
PACKAGE OPTION ADDENDUM
www.ti.com
10-Jun-2014
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
OPA360AIDCKR
ACTIVE
SC70
DCK
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
AUW
OPA360AIDCKRG4
ACTIVE
SC70
DCK
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
AUW
OPA360AIDCKT
ACTIVE
SC70
DCK
6
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
AUW
OPA360AIDCKTG4
ACTIVE
SC70
DCK
6
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
AUW
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
10-Jun-2014
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Jul-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
OPA360AIDCKR
SC70
DCK
6
3000
178.0
9.0
2.4
2.5
1.2
4.0
8.0
Q3
OPA360AIDCKR
SC70
DCK
6
3000
179.0
8.4
2.2
2.5
1.2
4.0
8.0
Q3
OPA360AIDCKT
SC70
DCK
6
250
178.0
9.0
2.4
2.5
1.2
4.0
8.0
Q3
OPA360AIDCKT
SC70
DCK
6
250
179.0
8.4
2.25
2.4
1.22
4.0
8.0
Q3
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Jul-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
OPA360AIDCKR
SC70
DCK
6
3000
180.0
180.0
18.0
OPA360AIDCKR
SC70
DCK
6
3000
195.0
200.0
45.0
OPA360AIDCKT
SC70
DCK
6
250
180.0
180.0
18.0
OPA360AIDCKT
SC70
DCK
6
250
195.0
200.0
45.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2014, Texas Instruments Incorporated