AD ADG726BSUZ

a
16-/32-Channel, 4 +1.8 V to +5.5 V, 2.5 V Analog Multiplexers
ADG726/ADG732
FEATURES
1.8 V to 5.5 V Single Supply
2.5 V Dual-Supply Operation
4 On Resistance
0.5 On Resistance Flatness
48-Lead TQFP or 48-Lead 7 mm 7 mm CSP Packages
Rail-to-Rail Operation
30 ns Switching Times
Single 32-to-1 Channel Multiplexer
Dual/Differential 16-to-1 Channel Multiplexer
TTL/CMOS Compatible Inputs
For Functionally Equivalent Devices with Serial Interface
See ADG725/ADG731
APPLICATIONS
Optical Applications
Data Acquisition Systems
Communication Systems
Relay Replacement
Audio and Video Switching
Battery-Powered Systems
Medical Instrumentation
Automatic Test Equipment
FUNCTIONAL BLOCK DIAGRAMS
ADG726
ADG732
S1
S1A
DA
S16A
D
S1B
DB
S32
S16B
WR
CSA
1-OF-16
DECODER
CSB
A0 A1 A2 A3 EN
WR
CS
1-OF-32
DECODER
A0 A1 A2 A3 A4 EN
GENERAL DESCRIPTION
PRODUCT HIGHLIGHTS
The ADG726/ADG732 are monolithic CMOS 32-channel/dual
16-channel analog multiplexers. The ADG732 switches one of
32 inputs (S1-S32) to a common output, D, as determined by
the 5-bit binary address lines A0, A1, A2, A3, and A4. The
ADG726 switches one of 16 inputs as determined by the 4-bit
binary address lines A0, A1, A2, and A3.
1. +1.8 V to +5.5 V single- or ± 2.5 V dual-supply operation.
These parts are specified and guaranteed with +5 V ± 10%,
+3 V ± 10% single-supply, and ± 2.5 V ± 10% dualsupply rails.
On-chip latches facilitate microprocessor interfacing. The
ADG726 device may also be configured for differential operation by tying CSA and CSB together. An EN input is used to
enable or disable the devices. When disabled, all channels are
switched OFF.
2. On resistance of 4 Ω
3. Guaranteed break-before-make switching action
4. 7 mm × 7 mm 48-lead chip scale package (CSP)
or 48-lead TQFP package
These multiplexers are designed on an enhanced submicron
process that provides low power dissipation yet gives high
switching speed, very low on resistance, and leakage currents.
They operate from a single supply of +1.8 V to +5.5 V and a ±2.5 V
dual supply, making them ideally suited to a variety of applications.
On resistance is in the region of a few ohms and is closely
matched between switches and very flat over the full signal
range. These parts can operate equally well as either multiplexers
or demultiplexers and have an input signal range that extends to
the supplies. In the OFF condition, signal levels up to the supplies
are blocked. All channels exhibit break-before-make switching
action, preventing momentary shorting when switching channels.
They are available in either 48-lead CSP or TQFP packages.
REV. 0
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties that
may result from its use. No license is granted by implication or otherwise
under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
www.analog.com
Fax: 781/326-8703
© Analog Devices, Inc., 2002
ADG726/ADG732–SPECIFICATIONS1 (V
DD = 5 V Parameter
ANALOG SWITCH
Analog Signal Range
On Resistance (RON)
On Resistance Match Between
Channels (∆RON)
On Resistance Flatness (RFLAT(ON))
LEAKAGE CURRENTS
Source OFF Leakage IS (OFF)
Drain OFF Leakage ID (OFF)
ADG726
ADG732
Channel ON Leakage ID, IS (ON)
ADG726
ADG732
DIGITAL INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current
IINL or IINH
CIN, Digital Input Capacitance
DYNAMIC CHARACTERISTICS2
tTRANSITION
+25C
B Version
–40C
to +85C
0 V to VDD
4
5.5
6
0.3
0.8
0.5
1
± 0.01
± 0.25
± 0.05
± 0.5
±1
± 0.05
± 0.5
±1
Unit
V
Ω typ
Ω max
Ω typ
Ω max
Ω typ
Ω max
10%, VSS = 0 V, GND = 0 V, unless otherwise noted.)
Test Conditions/Comments
VS = 0 V to VDD, IDS = 10 mA;
Test Circuit 1
VS = 0 V to VDD, IDS = 10 mA
VS = 0 V to VDD, IDS = 10 mA
VDD = 5.5 V
VD = 4.5 V/1 V, VS = 1 V/4.5 V;
Test Circuit 2
VD = 4.5 V/1 V, VS = 1 V/4.5 V;
Test Circuit 3
± 2.5
±5
nA typ
nA max
nA typ
nA max
nA max
nA typ
nA max
nA max
2.4
0.8
V min
V max
± 0.5
µA typ
µA max
pF typ
VIN = VINL or VINH
ns typ
ns max
ns typ
ns min
ns typ
ns max
ns typ
ns max
ns typ
ns max
ns typ
ns max
pC typ
RL = 300 Ω, CL = 35 pF, Test Circuit 5
VS1 = 3 V/0 V, VS32 = 0 V/3 V
RL = 300 Ω, CL = 35 pF;
VS = 3 V; Test Circuit 6
VS = 3 V; Test Circuit 7
RL = 300 Ω, CL = 35 pF;
VS = 3 V; Test Circuit 7
RL = 300 Ω, CL = 35 pF;
RL = 300 Ω, CL = 35 pF;
VS = 3 V; Test Circuit 8
RL = 300 Ω, CL = 35 pF;
VS = 3 V; Test Circuit 8
VS = 2.5 V, RS = 0 Ω, CL = 1 nF;
Test Circuit 9
RL = 50 Ω, CL = 5 pF, f = 1 MHz;
Test Circuit 10
RL = 50 Ω, CL = 5 pF, f = 1 MHz;
Test Circuit 11
RL = 50 Ω, CL = 5 pF; Test Circuit 12
±1
± 2.5
±5
0.005
5
VD = VS = 1 V, or 4.5 V;
Test Circuit 4
Charge Injection
23
34
18
1
18
25
17
23
24
32
16
22
5
OFF Isolation
–72
dB typ
Channel-to-Channel Crosstalk
–72
dB typ
34
18
13
MHz typ
MHz typ
pF typ
f = 1 MHz
170
340
pF typ
pF typ
f = 1 MHz
f = 1 MHz
175
350
pF typ
pF typ
f = 1 MHz
f = 1 MHz
10
µA typ
µA max
Break-Before-Make Time Delay, tD
tON(CS, WR)
tOFF(CS, WR)
tON(EN)
tOFF(EN)
–3 dB Bandwidth
ADG726
ADG732
CS (OFF)
CD (OFF)
ADG726
ADG732
CD, CS (ON)
ADG726
ADG732
POWER REQUIREMENTS
IDD
40
32
29
40
25
20
VDD = 5.5 V
Digital Inputs = 0 V or 5.5 V
NOTES
1
Temperature range is as follows: B Version: –40°C to +85°C.
Guaranteed by design; not subject to production test.
Specifications subject to change without notice.
2
–2–
REV. 0
ADG726/ADG732
SPECIFICATIONS1 (V
DD = 3
V 10%, VSS = 0 V, GND = 0 V, unless otherwise noted.)
B Version
–40C
+25C
to +85C
Parameter
ANALOG SWITCH
Analog Signal Range
On Resistance (RON)
0 V to VDD
7
11
On Resistance Match Between
Channels (∆RON)
On Resistance Flatness (RFLAT(ON))
LEAKAGE CURRENTS
Source OFF Leakage IS (OFF)
Drain OFF Leakage ID (OFF)
ADG726
ADG732
Channel ON Leakage ID, IS (ON)
ADG726
ADG732
DIGITAL INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current
IINL or IINH
± 0.01
± 0.25
± 0.05
± 0.5
±1
± 0.05
± 0.5
±1
12
0.35
1
3
V
Ω typ
Ω max
Ω typ
Ω max
Ω typ
Test Conditions/Comments
VS = 0 V to VDD, IDS = 10 mA;
Test Circuit 1
VS = 0 V to VDD, IDS = 10 mA
VS = 0 V to VDD, IDS = 10 mA
VDD = 3.3 V
VS = 3 V/1 V, VD = 1 V/3 V;
Test Circuit 2
VS = 1 V/3 V, VD = 3 V/1 V;
Test Circuit 3
± 2.5
±5
nA typ
nA max
nA max
nA max
nA max
nA typ
nA max
nA max
2.0
0.7
V min
V max
± 0.5
µA typ
µA max
pF typ
VIN = VINL or VINH
ns typ
ns max
ns typ
ns min
ns typ
ns max
ns typ
ns max
ns typ
ns max
ns typ
ns max
pC typ
RL = 300 Ω, CL = 35 pF; Test Circuit 5
VS1 = 2 V/0 V, VS32 = 0 V/2 V
RL = 300 Ω, CL = 35 pF;
VS = 2 V; Test Circuit 6
VS = 2 V; Test Circuit 7
RL = 300 Ω, CL = 35 pF;
VS = 2 V; Test Circuit 7
RL = 300 Ω, CL = 35 pF;
RL = 300 Ω, CL = 35 pF;
VS = 3 V; Test Circuit 8
RL = 300 Ω, CL = 35 pF;
VS = 2 V; Test Circuit 8
VS = 1.5 V, RS = 0 Ω, CL = 1 nF;
Test Circuit 9
RL = 50 Ω, CL = 5 pF, f = 1 MHz;
Test Circuit 10
RL = 50 Ω, CL = 5 pF, f = 1 MHz;
Test Circuit 11
RL = 50 Ω, CL = 5 pF; Test Circuit 12
±1
± 2.5
±5
0.005
CIN, Digital Input Capacitance
Unit
5
VS = VD = 1 V or 3 V;
Test Circuit 4
2
DYNAMIC CHARACTERISTICS
tTRANSITION
Charge Injection
34
52
26
1
29
43
26
38
33
48
19
25
1
Off Isolation
–72
dB typ
Channel-to-Channel Crosstalk
–72
dB typ
34
18
13
MHz typ
MHz typ
pF typ
f = 1 MHz
170
340
pF typ
pF typ
f = 1 MHz
f = 1 MHz
175
350
pF typ
pF typ
f = 1 MHz
f = 1 MHz
5
µA typ
µA max
Break-Before-Make Time Delay, tD
tON(WR, CS)
tOFF(WR, CS)
tON(EN, WR)
tOFF(EN)
–3 dB Bandwidth
ADG726
ADG732
CS (OFF)
CD (OFF)
ADG726
ADG732
CD, CS (ON)
ADG726
ADG732
POWER REQUIREMENTS
IDD
62
52
42
55
28
10
NOTES
1
Temperature ranges are as follows: B Version: –40°C to +85°C.
2
Guaranteed by design; not subject to production test.
Specifications subject to change without notice.
REV. 0
–3–
VDD = 3.3 V
Digital Inputs = 0 V or 3.3 V
ADG726/ADG732 SPECIFICATIONS1
DUAL SUPPLY (V
DD = +2.5
V ⴞ 10%, VSS = –2.5 V ⴞ 10%, GND = 0 V, unless otherwise noted.)
Parameter
+25ⴗC
ANALOG SWITCH
Analog Signal Range
On Resistance (RON)
B Version
–40ⴗC
to +85ⴗC
VSS to VDD
4
5.5
On Resistance Match Between
Channels (∆RON)
On Resistance Flatness (RFLAT(ON))
6
0.3
0.8
0.5
1
LEAKAGE CURRENTS
Source OFF Leakage IS (OFF)
Drain OFF Leakage ID (OFF)
ADG726
ADG732
Channel ON Leakage ID, IS (ON)
ADG726
ADG732
DIGITAL INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current
IINL or IINH
± 0.01
± 0.25
± 0.05
± 0.5
±1
± 0.05
± 0.5
±1
V
Ω typ
Ω max
Ω typ
Ω max
Ω typ
Ω max
Test Conditions/Comments
VS = VSS to VDD, IDS = 10 mA;
Test Circuit 1
VS = VSS to VDD, IDS = 10 mA
VS = VSS to VDD, IDS = 10 mA
VDD = +2.75 V, VSS = –2.75 V
VS = +2.25 V/–1.25 V, VD = –1.25 V/+2.25 V;
Test Circuit 2
VS = +2.25 V/–1.25 V, VD = –1.25 V/+2.25 V;
Test Circuit 3
± 2.5
±5
nA typ
nA max
nA max
nA max
nA max
nA typ
nA max
nA max
1.7
0.7
V min
V max
± 0.5
µA typ
µA max
pF typ
VIN = VINL or VINH
ns typ
ns max
ns typ
ns min
ns typ
ns max
ns typ
ns max
ns typ
ns max
ns typ
ns max
pC typ
RL = 300 ⍀, CL = 35 pF; Test Circuit 5
VS1 = 1.5 V/0 V, VS32 = 0 V/1.5 V
RL = 300 ⍀, CL = 35 pF;
VS = 1.5 V; Test Circuit 6
VS = 1.5 V; Test Circuit 7
RL = 300 ⍀, CL = 35 pF;
VS = 1.5 V; Test Circuit 7
RL = 300 ⍀, CL = 35 pF;
RL = 300 ⍀, CL = 35 pF;
VS = 1.5 V; Test Circuit 8
RL = 300 ⍀, CL = 35 pF;
VS = 1.5 V; Test Circuit 8
VS = 0 V, RS = 0 ⍀, CL = 1 nF;
Test Circuit 9
RL = 50 ⍀, CL = 5 pF, f = 1 MHz;
Test Circuit 10
RL = 50 ⍀, CL = 5 pF, f = 1 MHz;
Test Circuit 11
RL = 50 ⍀, CL = 5 pF; Test Circuit 12
± 0.5
± 2.5
±5
0.005
CIN, Digital Input Capacitance
Unit
5
VS = VD = +2.25 V/–1.25 V;
Test Circuit 4
2
DYNAMIC CHARACTERISTICS
tTRANSITION
Charge Injection
33
45
15
1
21
30
20
29
26
37
18
26
1
OFF Isolation
–72
dB typ
Channel-to-Channel Crosstalk
–72
dB typ
34
18
13
MHz typ
MHz typ
pF typ
137
275
pF typ
pF typ
f = 1 MHz
f = 1 MHz
150
300
pF typ
pF typ
f = 1 MHz
f = 1 MHz
µA typ
µA max
µA typ
µA max
VDD = +2.75 V
Digital Inputs = 0 V or +2.75 V
VSS = –2.75 V
Digital Inputs = 0 V or +2.75 V
Break-Before-Make Time Delay, tD
tON(CS, WR)
tOFF(CS, WR)
tON(EN, WR)
tOFF(EN)
–3 dB Bandwidth
ADG726
ADG732
CS (OFF)
CD (OFF)
ADG726
ADG732
CD, CS (ON)
ADG726
ADG732
POWER REQUIREMENTS
IDD
51
37
35
29
10
20
ISS
10
20
NOTES
1
Temperature range is as follows: B Version: –40°C to +85°C.
2
Guaranteed by design; not subject to production test.
Specifications subject to change without notice.
–4–
REV. 0
ADG726/ADG732
TIMING CHARACTERISTICS1, 2, 3
Parameter
Limit at TMIN, TMAX
Unit
Conditions/Comments
t1
t2
t3
t4
t5
t6
0
0
10
10
5
2
ns min
ns min
ns min
ns min
ns min
ns min
CS to WR Setup Time
CS to WR Hold Time
WR Pulsewidth
Time between WR Cycles
Address, Enable Setup Time
Address, Enable Hold Time
NOTES
1
See Figure 1.
2
All input signals are specified with tr = tf = 1 ns (10% to 90% of V DD).
3
Guaranteed by design and characterization, not production tested.
Specifications subject to change without notice.
CS
t1
t2
t3
t4
WR
t5
t6
A0, A1, A2, A3, (A4)
EN
Figure 1. Timing Diagram
Figure 1 shows the timing sequence for latching the switch
address and enable inputs. The latches are level sensitive; therefore, while WR is held low, the latches are transparent and the
switches respond to changing the address and enable the inputs.
REV. 0
Input data is latched on the rising edge of WR. The ADG726
has two CS inputs. This enables the part to be used either as a
dual 16-1 channel multiplexer or a differential 16-channel
multiplexer. If a differential output is required, tie CSA and
CSB together.
–5–
ADG726/ADG732
ABSOLUTE MAXIMUM RATINGS 1
(TA = 25°C, unless otherwise noted.)
VDD to VSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
VDD to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V
VSS to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . +0.3 V to –7 V
Analog Inputs2 . . . . . . . . . . . . . . VSS – 0.3 V to VDD + 0.3 V or
30 mA, Whichever Occurs First
Digital Inputs2 . . . . . . . . . . . . . . . . . . –0.3 V to VDD + 0.3 V or
30 mA, Whichever Occurs First
Peak Current, S or D . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 mA
(Pulsed at 1 ms, 10% Duty Cycle Max)
Continuous Current, S or D . . . . . . . . . . . . . . . . . . . . . 30 mA
Operating Temperature Range
Industrial (B Version) . . . . . . . . . . . . . . . . . –40°C to +85°C
Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C
Thermal Impedence (Four-layer board)
48-Lead LFCSP . . . . . . . . . . . . . . . . . . . . . . . . . . . 25⬚C/W
48-Lead TQFP . . . . . . . . . . . . . . . . . . . . . . . . . . . 54.6⬚C/W
Lead Temperature, Soldering (10 sec) . . . . . . . . . . . . . 300°C
IR Reflow, Peak Temperature (<20 sec) . . . . . . . . . . . . 235°C
NOTES
1
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of
the device at these or any other conditions above those listed in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability. Only one absolute
maximum rating may be applied at any one time.
2
Overvoltages at A, EN, WR, CS, S, or D will be clamped by internal diodes.
Current should be limited to the maximum ratings given.
ORDERING GUIDE
Model
Temperature Range Package Description
Package Option
ADG726BCP
ADG726BSU
ADG732BCP
ADG732BSU
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
CP-48
SU-48
CP-48
SU-48
Chip Scale Package (LPCSP)
Thin Quad Flatpack (TQFP)
Chip Scale Package (LPCSP)
Thin Quad Flatpack (TQFP)
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the ADG726/ADG732 features proprietary ESD protection circuitry, permanent damage
may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
NC = NO CONNECT
PIN 1
INDICATOR
ADG732
TOP VIEW
S12A 1
S11A 2
S10A 3
S9A 4
S8A 5
S7A 6
S6A 7
S5A 8
S4A 9
S3A 10
S2A 11
S1A 12
36 S28
35 S27
34 S26
33 S25
32 S24
31 S23
30 S22
29 S21
28 S20
27 S19
26 S18
25 S17
VDD 13
VDD 14
A0 15
A1 16
A2 17
A3 18
A4 19
CS 20
WR 21
EN 22
GND 23
VSS 24
S12 1
S11 2
S10 3
S9 4
S8 5
S7 6
S6 7
S5 8
S4 9
S3 10
S2 11
S1 12
NC = NO CONNECT
–6–
PIN 1
INDICATOR
ADG726
TOP VIEW
36 S12B
35 S11B
34 S10B
33 S9B
32 S8B
31 S7B
30 S6B
29 S5B
28 S4B
27 S3B
26 S2B
25 S1B
VDD 13
VDD 14
A0 15
A1 16
A2 17
A3 18
CSA 19
CSB 20
WR 21
EN 22
GND 23
VSS 24
48 S13
47 S14
46 S15
45 S16
44 NC
43 D
42 NC
41 NC
40 S32
39 S31
38 S30
37 S29
48 S13A
47 S14A
46 S15A
45 S16A
44 NC
43 DA
42 NC
41 DB
40 S16B
39 S15B
38 S14B
37 S13B
PIN CONFIGURATIONS
LFCSP and TQFP
REV. 0
ADG726/ADG732
Table I. ADG726 Truth Table
A3
A2
A1
A0
EN
CSA
CSB
WR
ON Switch
X
X
X
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
X
X
X
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
X
X
X
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
X
X
X
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
X
X
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
L->H
X
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Retains Previous Switch Condition
No Change in Switch Condition
NONE
S1A–DA, S1B–DB
S2A–DA, S2B–DB
S3A–DA, S3B–DB
S4A–DA, S4B–DB
S5A–DA, S5B–DB
S6A–DA, S6B–DB
S7A–DA, S7B–DB
S8A–DA, S8B–DB
S9A–DA, S9B–DB
S10A–DA, S10B–DB
S11A–DA, S11B–DB
S12A–DA, S12B–DB
S13A–DA, S13B–DB
S14A–DA, S14B–DB
S15A–DA, S15B–DB
S16A–DA, S16B–DB
X = Don’t Care
Table II. ADG732 Truth Table
A4
A3
A2
A1
A0
EN
CS
WR
Switch Condition
X
X
X
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
X
X
X
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
X
X
X
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
X
X
X
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
X
X
X
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
X
X
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
L->H
X
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Retains Previous Switch Condition
No Change in Switch Condition
NONE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
X = Don’t Care
REV. 0
–7–
ADG726/ADG732
TERMINOLOGY
VDD
Most Positive Power Supply Potential
VSS
IDD
ISS
GND
S
D
IN
VD (VS)
RON
∆RON
RFLAT(ON)
Most Negative Power Supply in a Dual-Supply Application. In single-supply applications, connect to GND.
Positive Supply Current
Negative Supply Current
Ground (0 V) Reference
Source Terminal. May be an input or output.
Drain Terminal. May be an input or output.
Logic Control Input
Analog Voltage on Terminals D and S
Ohmic Resistance between D and S
On Resistance Match between any two channels, i.e., RONmax – RONmin
Flatness is defined as the difference between the maximum and minimum value of on resistance as measured
over the specified analog signal range.
Source Leakage Current with the Switch OFF
Drain Leakage Current with the Switch OFF
Channel Leakage Current with the Switch ON
Maximum Input Voltage for Logic “0”
Minimum Input Voltage for Logic “1”
Input Current of the Digital Input
OFF Switch Source Capacitance. Measured with reference to ground.
OFF Switch Drain Capacitance. Measured with reference to ground.
ON Switch Capacitance. Measured with reference to ground.
Digital Input Capacitance
Delay Time Measured between the 50% and 90% Points of the Digital Inputs and the Switch ON Condition
when Switching from One Address State to Another
Delay Time between the 50% and 90% Points of the EN Digital Input and the Switch ON Condition
Delay Time between the 50% and 90% Points of the EN Digital Input and the Switch OFF Condition
OFF Time Measured between the 80% Points of Both Switches when Switching from One Address State to Another
A Measure of the Glitch Impulse Transferred from the Digital Input to the Analog Output During Switching
IS (OFF)
ID (OFF)
ID, IS (ON)
VINL
VINH
IINL(IINH)
CS (OFF)
CD (OFF)
CD, CS(ON)
CIN
tTRANSITION
tON(EN)
tOFF(EN)
tOPEN
Charge
Injection
OFF Isolation
Crosstalk
A Measure of Unwanted Signal Coupling through an OFF Switch
A Measure of Unwanted Signal Coupling from One Channel to Another as a Result of Parasitic Capacitance
ON Response
The Frequency Response of the ON Switch
Insertion
Loss
The Loss Due to the On Resistance of the Switch
–8–
REV. 0
Typical Performance Characteristics—ADG726/ADG732
8
7
RESISTANCE – RESISTANCE – VDD = 5.5V
5
VDD = 3.3V
4
8
7
7
3
VDD = 4.5V
2
VDD = 5V
1
5
0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5
VD, VS – V
6
4
VDD = +2.75V
VSS = –2.75V
3
8
1.25
2.25
0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
VD, VS – V
0.5
VDD = 5V
VSS = 0V
0.4
0.3
+85C
6
5
–40C
3
CURRENT – nA
6
RESISTANCE – RESISTANCE – 0
TPC 3. On Resistance vs. VD(VS)
for Different Temperatures,
Single Supply
7
4
–40C
0
–0.75
0.25
VD, VS – V
8
+25C
3
1
VSS = 0V
7
+25C
1
–1.75
+85C
4
2
TPC 2. On Resistance vs. VD(VS),
Dual Supply
TPC 1. On Resistance vs. VD(VS),
Single Supply
5
2
0
–2.75
0
TA = +25C
VDD = +2.5V
VSS = –2.5V
VDD = +2.25V
VSS = –2.25V
6
VDD = 3.0V
6
8
VSS = 0V
TA = +25C
VSS = 0V
RESISTANCE – VDD = 2.7V
5
+85C
4
+25C
3
0.2
0.1
0
–0.1
–0.2
–40C
2
2
1
1
–0.4
0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3.0
VD, VS – V
0
–2.5 –2.0 –1.5 –1.0 –0.5 0 0.5 1.0 1.5 2.0 2.5
VD, VS – V
–0.5
TPC 4. On Resistance vs. VD(VS),
Single Supply
TPC 5. On Resistance vs. VD(VS),
Dual Supply
–0.3
0
0
25
45
20
40
15
5
25
35
45
55
65
TEMPERATURE – C
75
85
TPC 6. Leakage Currents vs.
Temperature
1.8
35
15
30
TIME – ns
QINJ – pC
10
5
0
VDD = 3V
25 t
ON
VDD = 5V
20
15
–5
VDD = 3V
VDD = 5V
tOFF
10
–10
5
TA = +25C
–15
LOGIC THRESHOLD VOLTAGE – V
VSS = 0V
–3
–2
–1
0
1
2
VD, VS – V
3
4
5
TPC 7. ADG732 Charge Injection
vs. Source Voltage
REV. 0
0
–40
–20
0
20
40
TEMPERATURE – C
60
80
TPC 8. tON/tOFF Times vs. Temperature
–9–
1.6
1.4
1.2
RISING
1.0
FALLING
0.8
0.6
0.4
0.2
0
TA = 25C
0
1
2
3
4
5
6
VDD – V
TPC 9. Logic Threshold Voltage
vs. Supply Voltage
ADG726/ADG732
0
0
VDD = 5V
TA = 25C
–10
–10
–30
–40
–50
–60
–70
–30
–40
–50
–60
–70
–80
–80
–90
–90
0.1
1
10
FREQUENCY – MHz
–4
ADG732
–6
–8
–10
–12
–100
0.03
100
TPC 10. OFF Isolation vs. Frequency
Test Circuits
ATTENUATION – dB
ATTENUATION – dB
ATTENUATION – dB
ADG726
VDD = 5V
TA = 25C
–2
–20
–20
–100
0.03
0
VDD = 3V, 5V
TA = 25C
0.1
1
10
FREQUENCY – MHz
–14
0.03
100
0.1
S1
V1
VDD
VSS
VDD
VSS
D
S2
D
ID(OFF)
A
S32
VS
VS
100
TPC 12. ON Response vs. Frequency
TPC 11. Crosstalk vs. Frequency
IDS
S
1
10
FREQUENCY – MHz
EN
GND
VD
LOGIC “1”
RON = V1 /IDS
Test Circuit 1. On Resistance
IS(OFF)
S1
A
VDD
VSS
VDD
VSS
D
S2
VS
Test Circuit 3. ID (OFF)
VSS
VDD
VSS
D
S1
ID(ON)
A
S32
S32
EN
VS
GND
LOGIC “1”
VS
VD
GND
Test Circuit 2. IS (OFF)
VDD
VSS
VDD
VSS
A4
VIN
VDD
50
VD
LOGIC “ 0”
Test Circuit 4. ID (ON)
3V
S1
ADDRESS
DRIVE (VIN)
VS1
50%
50%
0V
S2 THRU S31
A0
VS1
VS32
S32
ADG732*
EN
D
RL
300
EN CS GND WR
CL
35pF
90%
VOUT
VOUT
90%
VS32
tTRANSITION
tTRANSITION
*SIMILAR CONNECTION FOR ADG726
Test Circuit 5. Switching Time of Multiplexer, tTRANSITION
VDD
VSS
VDD
VSS
A4
VIN
50
3V
S1
VS
ADDRESS
DRIVE (VIN)
S2 THRU S31
A0
0V
S32
ADG732*
VS
D
EN CS GND WR
RL
300
CL
35pF
VOUT
VOUT
80%
80%
tOPEN
*SIMILAR CONNECTION FOR ADG726
Test Circuit 6. Break-Before-Make Delay, tOPEN
–10–
REV. 0
ADG726/ADG732
VDD
VSS
VDD
VSS
3V
A4
WR
S1
50%
0V
VS
S2 THRU S32
A0
CS
ADG732*
VCS
WR
EN
D
CL
35pF
RL
300
GND
VWR
SWITCH
OUTPUT
VOUT
VO
tON (WR)
20%
0V
tOFF (WR)
20%
*SIMILAR CONNECTION FOR ADG726
Test Circuit 7. Write Turn-ON and Turn-OFF Time, tON, tOFF (WR)
VDD
VSS
VDD
VSS
A4
3V
S1
VS
50%
EN
A0
tON (EN)
EN
VEN
ADG732*
CS
50%
0V
S2 THRU S32
GND
D
CL
35pF
RL
300
WR
VOUT
SWITCH
OUTPUT
VO
tOFF (EN)
10%
90%
0V
*SIMILAR CONNECTION FOR ADG726
Test Circuit 8. Enable Delay, tON (EN), tOFF (EN)
A4
VDD
VSS
VDD
VSS
3V
A0
LOGIC
INPUT (VIN)
ADG732*
RS
S
D
CL
1nF
EN
VS
VIN
CS
0V
VOUT
VOUT
GND WR
QINJ = C L V OUT
*SIMILAR CONNECTION FOR ADG726
Test Circuit 9. Charge Injection
VDD
VSS
0.1F
0.1F
VDD
VSS
NETWORK
ANALYZER
50
A4
A0
S
50
D
LOGIC “ 1”
VS
VOUT
RL
50
EN
ADG732*
GND
OFF ISOLATION = 20 LOG
*SIMILAR CONNECTION FOR ADG726
Test Circuit 10. OFF Isolation
REV. 0
–11–
VOUT
VS
VOUT
ADG726/ADG732
VDD
VSS
0.1F
VSS
VDD
VSS
S1
50
A4
S2
A0
VDD
NETWORK
ANALYZER
50
VSS
NETWORK
ANALYZER
50
A4
A0
S
VS
VS
S32
ADG732*
0.1F
D
VOUT
RL
50
EN
VOUT
D
ADG732*
RL
50
C02765–0–7/02(0)
VDD
GND
EN CS GND WR
INSERTION LOSS = 20 LOG
*SIMILAR CONNECTION FOR ADG726
CHANNEL-TO-CHANNEL CROSSTALK = 20LOG10 (VOUT/VS)
VOUT WITH SWITCH
VOUT WITHOUT SWITCH
*SIMILAR CONNECTION FOR ADG726
Test Circuit 11. Channel-to-Channel Crosstalk
Test Circuit 12. Bandwidth
OUTLINE DIMENSIONS
48-Lead Frame Chip Scale Package [LFCSP]
(CP-48)
Dimensions shown in millimeters
7.00
BSC SQ
0.30
0.23
0.18
0.60 MAX
0.60 MAX
37
5.25
4.70
2.25
BOTTOM
VIEW
0.50
0.40
0.30
12
25
24
13
5.50
REF
0.70 MAX
0.65 NOM
COPLANARITY
0.05 MAX
0.02 NOM
0.50 BSC
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-220-VKKD-2
48-Lead Thin Plastic Quad Flatpack [TQFP]
(SU-48)
Dimensions shown in millimeters
1.20 MAX
PRINTED IN U.S.A.
0.25
REF
1
6.75
BSC SQ
TOP
VIEW
12 MAX
48
36
PIN 1
INDICATOR
1.00
0.90
0.80
PIN 1
INDICATOR
9.00 BSC SQ
0.75
0.60
0.45
37
48
36
1
7.00
BSC
SQ
TOP VIEW
(PINS DOWN)
COPLANARITY
0.15
0.05
0
MIN
25
12
13
24
0.5
BSC
0.20
0.09
0.27
0.22
0.17
7
0
1.05
1.00
0.95
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MS-026BBC
–12–
REV. 0