www.fairchildsemi.com AN-6300 FAN6300 / FAN6300A / FAN6300H Highly Integrated Quasi-Resonant PWM Controller Abstract This application note describes a detailed design strategy for higher-power conversion efficiency and better EMI using a Quasi-Resonant PWM controller compared to the conventional, hard-switched converter with a fixed switching frequency. Based on the proposed design guideline, a design example with detailed parameters demonstrates the performance of the controller. range line voltage and reduces switching loss to minimize switching voltage on drain of the power MOSFET. Introduction FAN6300/A/H controller provides many protection functions. Pulse-by-pulse current limiting ensures the fixed peak current limit level, even when short-circuit occurs. Once an open-circuit failure occurs in the feedback loop, the internal protection circuit disables PWM output immediately. As long as VDD drops below the turn-off threshold voltage, the controller also disables the PWM output. The gate output is clamped at 18V to protect the power MOS from high gate-source voltage conditions. The minimum tOFF time limit prevents the system frequency from being too high. If the DET pin reaches OVP level, internal OTP is triggered, and the power system enters latch-mode until AC power is removed. The highly integrated FAN6300/A/H PWM controller provides several features to enhance the performance of flyback converters. FAN6300/A are applied on QuasiResonant flyback converter where maximum operating frequency is below 100kHz and FAN6300H is suitable for high frequency operation that is around 190kHz. A built-in High Voltage (HV) startup circuit can provide more startup current to reduce the startup time of the controller. Once the VDD voltage exceeds the turn-on threshold voltage, the HV startup function is disabled immediately to reduce power consumption. An internal valley voltage detector ensures power system operates in quasi-resonant operation in wide- © 2009 Fairchild Semiconductor Corporation Rev. 1.0.2 • 5/21/10 To minimize standby power consumption and improve lightload efficiency, a proprietary green-mode function provides off-time modulation to decrease switching frequency and perform extended valley voltage switching to keep to a minimum switching voltage. www.fairchildsemi.com AN-6300 APPLICATION NOTE Figure 1. Basic Quasi-Resonant Converter HV VDD 8 6 4.2V FB 2 Soft-Start 5ms 27V 2R Timer 55ms R Internal Bias OVP IHV Latched Two Steps UVLO 16V/10V/8V FB OLP 2ms 30µs Starter CS 3 DRV Blanking Circuit Over-Power Compensation S PWM Current Limit R IDET 1 VDET Valley Detector 1st Valley CLR Q tOFF-MIN +9µs tOFF-MIN +5µs for H version Latched DET OVP Internal OTP 0.3V 5V GATE Latched 0.3V VDET tOFF S/H Blanking (4µs) 2.5V (1.5µs) for H version DET 5 Q 18V (3µs/13µs) for H version tOFF-MIN (8µs/38µs) SET IDET Latched 4 7 GND NC Figure 2. Functional Block Diagram © 2009 Fairchild Semiconductor Corporation Rev. 1.0.2 • 5/21/10 www.fairchildsemi.com 2 AN-6300 APPLICATION NOTE Design Procedure for the Primary-Side Inductance of Transformer In this section, a design procedure is described using the schematic of Figure 1 as a reference. designed to turn on the MOSFET when Vds reaches its minimum voltage Vin-n(Vo+Vd). [a] Define the System Specifications Line voltage range (Vin,min and Vin,max) Maximum output power (Po). Output voltage (Vo) and maximum output current (Io) Estimated efficiency (η) The power conversion efficiency must be estimated to calculate the maximum input power. In the case of NB adaptor applications, the typical efficiency is 85%~90%. n:1 + n(Vo+Vd) - Po + - + Vds Coss - (1) η [b] Estimate Reflected Output Voltage Vds = Vin,max + n(Vo + Vd ) n(Vo+Vd) Vin,max n(Vo+Vd) n(Vo+Vd) 0V Figure 3. Typical Waveform of MOSFET Drain Voltage for QR Operation (2) Ids where the turns ratio of primary to secondary side of transformer is defined as n and Vds is as specified in Equation 2. By increasing n, the capacitive switching loss and conduction loss of the MOSFET is reduced. However, this increases the voltage stress on the MOSFET as shown in Figure 3. Therefore, determine n by a trade-off between the voltage margin of the MOSFET and the efficiency. Typically, a turn-off voltage spike of Vds is considered as 100V, thus Vds,max is designed around 490~550V (75~85% of MOSFET rated voltage). Idspk Iin Id DTs Vds [c] Determine the Transformer Primary-side Inductance (LP) Vin+n(Vo+Vd) n(Vo+Vd) Figure 4 shows the typical waveforms of MOSFET drain current (Ids), secondary diode current (Id), and the MOSFET drain voltage (Vds) of a QR converter. During tOFF, the current flows through the secondary side rectifier diode. When Id reduces to zero, Vds begins to drop by the resonance between the effective output capacitor of the MOSFET and the primary-side inductance (LP). To minimize the switching loss, the FAN6300/A/H is © 2009 Fairchild Semiconductor Corporation Rev. 1.0.2 • 5/21/10 n(Vo+Vd) Vds Figure 3 shows the typical waveforms of the drain voltage of quasi-resonant flyback converter. When the MOSFET is turned off, the DC link voltage (Vo), together with the output voltage (Vo) and the forward voltage drop of the Schottky diode (Vd) reflected to the primary, are imposed on the MOSFET. The maximum nominal voltage across the MOSFET (Vds) is: Vds,max - Vo + With the estimated efficiency, the maximum input power is given by: Pin = + Vd Vin Vin tON n(Vo+Vd) Vin-n(Vo+Vd) tOFF tF TS Figure 4. Typical Waveform of QR Operation www.fairchildsemi.com 3 AN-6300 APPLICATION NOTE To determine the primary-side inductance (LP), the following variables should be determined beforehand: [d] Determine the Proper Core and the Minimum Primary Turns The minimum switching frequency (fs,min): The maximum average input current occurs at the minimum input voltage and full-load condition. Meanwhile, the switching frequency is at minimum value during QR operation. The falling time of the MOSFET drain voltage (tf): As shown in Figure 4, the falling time of MOSFET drain voltage is half of the resonant period of the MOSFET effective output capacitance and primaryside inductance. If a resonant capacitor is added to be paralleled with Coss, tf can be increased and EMI can be reduced. However, this forces a switching loss increase. The typical value of tf for NB adaptor application is about 0.5~1μs. When designing the transformer, consider the maximum flux density swing in normal operation (Bmax). The maximum flux density swing in normal operation is related to the hysteresis loss in the core, while the maximum flux density in transient is related to the core saturation. From Faraday’s law, the minimum number of turns for the transformer primary side is given by: NP,min n(Vo + Vd ) n(Vo + Vd ) + Vin × (1 - fs,min × tf ) = Vo I o 1 2 Dmax Ids,max pk (9) The number of turns for auxiliary winding (Na) can be obtained by: V + VD1 Na = DD (10) Vo + Vd According to Figure 3, Iin,max can be obtained as: I in,max = ×10 6 Determine the Number of Turns for Auxiliary Winding (4) Vin,min η Bmax Ae Generally, it is possible to use Bmax =0.25~0.30 T. (3) where Vin,min is specified at low-line and full-load. According to Equation 1, the maximum average input current Iin,max is determined as I in,max pk where: LP is specified in Equation 7; Ids,maxpk is the peak drain current specified in Equation 6; Ae is the cross-sectional area of the core in mm2; and Bmax is the maximum flux density swing in tesla. After determining fs,min and tf, the maximum duty cycle is calculated as: Dmax = = LP Ids,max where: VDD is the operating voltage for VDD pin; VD1 is the forward voltage drop of D1 in Figure 5; and Vo and Vd as determined in Equation 2. (5) Ids,maxpk can be determined as: I ds,max pk = Vin,min Dmax (6) Lm fs,min In Equation 5, replace Ids,maxpk by Equation 6, then combine Equations 4 and 5 to obtain LP: (Vin,min Dmax ) 2 LP = (7) 2Pin fs,min where Pin, and Dmax are specified in Equations 1 and 3, respectively, and fs,min is the minimum switching frequency. Once LP is determined, the RMS current of the MOSFET in normal operation are obtained as: I ds,max rms = Dmax 3 Ids,max peak © 2009 Fairchild Semiconductor Corporation Rev. 1.0.2 • 5/21/10 (8) www.fairchildsemi.com 4 AN-6300 APPLICATION NOTE When the supply current is drawn from the transformer, it draws a leakage current of about 1μA for the HV pin. The maximum power dissipation of the RHV is: Determine the Startup Circuitry When the power is turned on, the internal current (typically 1.2mA) charges the capacitor C1 through a forward diode D2 and a startup resistor RHV. During the startup sequence, the VAC from the AC terminal provides a startup current of about 1.2mA and charges the capacitor C1. RHV and D2 series connections can be directly connected by VAC to the HV pin. As the VDD pin reaches the turn-on threshold voltage VDD-ON, the FAN6300/A/H activates and signals the MOSFET. The HV startup circuit switches off and D1 is turned on when the energy of the main transformer is delivered to secondary and auxiliary winding. PR = IHV - LC(typ.) × RHV 2 (12) HV where IHV-LC is the supply current drawn from the HV pin. PR = 1μA2 x 100KΩ ≅ 0.1μW (13) HV The FAN6300/A/H has a voltage detector on the VDD pin to ensure that the chip has enough power to drive the MOSFET. Figure 7 shows a hysteresis of the turn-on and turn-off threshold levels. IDD VDD-ON 4.5mA VAC D2 R HV IHV HV 8 80μA tD-ON VDD 10μA D1 8V 6 GND The turn-on and turn-off threshold voltage are internally fixed at 16V and 10V. During startup, C1 must be charged to 16V to enable the IC. The capacitor continues to supply the VDD until the energy can be delivered from the auxiliary winding of the main transformer. The VDD must not drop below 10V during the startup sequence. 4 The maximum power-on delay time is determined as: If the secondary output short circuits or the feedback loop is open, the FB pin voltage rises rapidly toward the openloop voltage, VFB-OPEN. Once the FB voltage remains above VFB-OLP and lasts for tD-OLP, the FAN6300/A/H stops emitting output pulses. To further limit the input power under short-circuit or open-loop conditions, a special twostep UVLO mechanism has been built in to prolong this discharge time of the VDD capacitor. In Figure 8, the twostep UVLO mechanism decreases the operating current and pulls the VDD voltage toward the VDD-OFF. This sinking current is disabled after the VDD drops below VDD-OFF. The VDD voltage is again charged towards VDD-ON. With the addition of the two-step UVLO mechanism, the average input power during a short-circuit or open-loop condition is greatly reduced. When the gate pulses are emitted, the start-timer tSTARTER with 30μs per cycle is enabled. The 30μs start timer is enabled during startup until the output voltage is established, when the feedback voltage (VFB) is larger than 4.2V. C1 × VDD −ON (11) 1.2mA where VDD-ON is the FAN6300/A/H turn-on threshold voltage and tD-ON is the power-on delay time of the converter. t D −ON = If a shorter startup time is required, a two-step startup circuit, as shown in Figure 6, is recommended. In this circuit, a smaller C1 capacitor can be used to reduce the startup time. The energy supporting the FAN6300/A/H after startup is mainly from a larger capacitor C2. VDD-ON VAC D2 tD-ON RHV IHV VDD D1 D2 6 C1 FAN6300/A/H GND VDD Figure 7. UVLO Specification Figure 5. Startup Circuit for Power Transfer HV 16V C1 FAN630 0/A/H 8 10V C2 4 Figure 6. Two-Step Circuit Providing Power © 2009 Fairchild Semiconductor Corporation Rev. 1.0.2 • 5/21/10 Figure 8. FAN6300/A/H UVLO Effect www.fairchildsemi.com 5 AN-6300 APPLICATION NOTE Detection Pin Circuitry Figure 9 shows the DET pin circuitry. The DET pin is connected to an auxiliary winding by RDET and RA. The voltage divider is used for the following purposes: Detects the valley voltage of the switching waveform to achieve the valley voltage switching. This ensures QR operation, minimizes switching losses, and reduces EMI. Produces an offset to compensate the threshold voltage of the peak current limit to provide a constant power limit. The offset is generated in accordance with the input voltage with the PWM signal enabled. Figure 10. Voltage Sampled After 4µs(1.5µs for H version) Blanking Time After Switch-off Sequence A voltage comparator and a 2.5V reference voltage provide an output OVP protection. The ratio of the divider determines what output voltage level to stop gate. RDET + DET VAUX RA VDET tOFF S/H Blanking (4µs) 2.5V (1.5µs) for H version 1 - Latched DET OVP 0.3V 5V 6 VDD DET 1 To VDD Figure 9. Detection Pin Section + RDET First, determine the ratio of the voltage divider resisters. The ratio of the divider determines what output voltage level to stop gate. In Figure 10, the sampling voltage VS is: VS = NA NS ⋅VO ⋅ RA RDET + R A <2.5V Vo RA where NA is the number of turns for the auxiliary winding and NS is the number of turns for the secondary winding. Figure 11. Output Voltage OVP Detection Block Once the secondary-side switching current discharges to zero, a valley signal is generated on the DET pin. It detects the valley voltage of the switching waveform to achieve the valley voltage switching. When the voltage of auxiliary winding VAUX is negative (as defined in Figure 9), the DET pin voltage is clamped to 0.3V. RDET is recommended as 150kΩ to 220kΩ to achieve valley voltage switching. After the platform voltage VS in Figure 10 is determined, RA can be calculated by Equation 14. Figure 11 shows the output voltage OVP detection block of using auxiliary winding to detect Vo. In normal condition, VS is designed to be below 2.5V. The nominal voltage of VS is designed around 80% of the reference voltage 2.5V; thus, the recommended value for VS is 1.9V~2.1V. The output over-voltage protection works by the sampling voltage after the switching-off sequence. A 4μs blanking time ignores the leakage inductance ringing. If the DET pin OVP is triggered, the power system enters latch mode until AC power is removed. © 2009 Fairchild Semiconductor Corporation Rev. 1.0.2 • 5/21/10 - (14) Figure 12 shows the internal valley detection block of FAN6300/A/H. The internal timer (minimum tOFF time) prevents the system frequency from being too high. First valley switching is activated after minimum tOFF time 8μs(3µs for H version) is counted. Figure 13 shows a typical drain voltage waveform with first valley switching. www.fairchildsemi.com 6 AN-6300 APPLICATION NOTE To SR F/F VFB (3µs/13µs) for H version 0.3V tOFF- MIN (8µs/38µs) Valley Detector VDET DET 1 tOFF- MIN 1 st +9µs Valley tOFF-MIN +5µs for H version 0.3V 5V Figure 14. VFB vs. tOFF-MIN Curve To VDD RDET Vin + VAUX RA - Figure 12. Valley Detection Block Figure 15. QR Operation in Extended Valley Voltage Detection Mode Figure 13. First Valley Switching The proprietary green-mode function provides off-time modulation to linearly decrease the switching frequency under light-load conditions. VFB, which is derived from the voltage feedback loop, is taken as the reference. In Figure 14, once VFB is lower than 2.1V, the tOFF-MIN time increases linearly with lower VFB. The valley voltage detection signal does not start until the tOFF-MIN time finishes. Therefore, the valley detect circuit is activated until the tOFF-MIN time finishes, which decreases the switching frequency and provides extended valley voltage switching. In very light load conditions, it might fail to detect the valley voltage after the tOFF-MIN expires. Under this condition, an internal tTIME-OUT signal initiates a new cycle start after a 9μs(5µs for H version) delay. Figure 15 and Figure 16 show the two different conditions. © 2009 Fairchild Semiconductor Corporation Rev. 1.0.2 • 5/21/10 Figure 16. Internal tTIME_OUT Initiates New Cycle After Failure to Detect Valley Voltage (with 5µs Delay for FAN6300H) Figure 17 shows the VFB vs. PWM frequency curve, where fs,min is the minimum switching frequency at the minimum input voltage and full load condition, fs,max is maximum switching frequency during first valley switching, and fs,g is the minimum frequency when a 9μs(5µs for H version) timer is enabled. When output load is gradually lighter from maximum load, VFB becomes lower. Once VFB is below 2.1V, the green-mode function is activated; thus tOFF time is extended linearly. The flyback converter is forced to enter discontinuous conduction mode (DCM); therefore, the switching frequency fs can be decreased once the MOSFET drain voltage is switched at further extended valley voltage (2nd, 3rd, 4th, 5th …valley, etc.). fs,g is larger than 20kHz to prevent audio noise. Once the converter enters deep DCM, VFB is lower than 1.2V. Meanwhile, the www.fairchildsemi.com 7 AN-6300 APPLICATION NOTE on the FB pin to the GND can further increase the stability. The maximum sourcing current of the FB pin is 1.2mA. The phototransistor must be capable of sinking this current to pull FB level down at no load. The value of the biasing resistor Rb is determined as: 2ms timer tSTARTER is enabled and fs is around 500Hz to save power. Switching frequency (Hz) fs,max VO - VD - VZ fs,min Rb ⋅ K ≥ 1.2mA (16) where: VD is the drop voltage of photodiode, approx. 1.2V; VZ is the minimum operating voltage; 2.5V of the shunt regulator; and K is the current transfer rate (CTR) of the opto-coupler. fs,g 20k 2k For an output voltage VO = 5V, with CTR=100%, the maximum value of Rb is 860Ω. VFB 1.2V 2.1V VFB,max Vo Figure 17. VFB vs. Switching Frequency Curve RDET determines the extended valley switching capability. A typical value for RDET is 150k-220kΩ. A smaller value for RDET enhances the extended valley switching capability, thus further extended valley voltage can be switched. In different applications, the falling time of the MOSFET drain voltage (tf, in Figure 4) may cause the valley switching voltage to be imprecise. Adjust the RDET value or add a capacitor CA connected from DET pin to GND may be helpful to the valley switching voltage. The recommended value for CA is below 22pF. RFB FB Rb R1 C1 R3 CFB R2 Figure 18. Feedback Circuit RDET also affects the H/L line constant power limit. To compensate this variation for wide AC input range, the DET pin produces an offset voltage to compensate the threshold voltage of the peak current limit to provide a constant-power limit. The offset is generated in accordance with the input voltage when the PWM signal is enabled. This results in a lower current limit at high-line inputs than low-line inputs. At fixed-load condition, the CS limit is higher when the value of RDET is higher. Leading-Edge Blanking (LEB) A voltage signal proportional to the MOSFET current develops on the current-sense resistor RS. Each time the MOSFET is turned on, a spike induced by the diode reverse recovery and by the output capacitances of the MODFET and diode, appears on the sensed signal. A leading-edge blanking time of about 300ns has been introduced to avoid premature termination of MOSFET by the spike. Therefore, only a small-value RC filter (e.g. 100Ω+470pF) is required between the SENSE pin and RS. A non-inductive resistor for the RS is recommended. Design the Feedback Control FAN6300/A/H is designed for peak-current-mode control. Current-to-voltage conversion is accomplished externally with a current-sense resistor RS. In normal operation, the FB level controls the peak inductor current IPK is: VFB − 1.2 3 × RS where VFB is the voltage of FB pin. I PK = (15) When VFB is less than 1.2V, the start-timer tSTARTER, with 500μs per cycle, is enabled. Figure 19. Turn-On Spike Figure 18 is a typical feedback circuit consisting mainly of a shunt regulator and opto-coupler. R1 and R2 from a voltage divider are for the output voltage regulation. R3 and C1 are adjusted for control-loop compensation. A small-value RC filter (e.g. RFB =10Ω, CFB = 10nF) placed © 2009 Fairchild Semiconductor Corporation Rev. 1.0.2 • 5/21/10 www.fairchildsemi.com 8 AN-6300 APPLICATION NOTE Two kinds of commonly used transformer structure are introduced as follows: Output Driver / Soft Driving The output stage is a fast totem-pole driver that can drive a MOSFET gate directly. It is also equipped with a voltage clamping Zener diode to protect the MOSFET from damage caused by undesirable over-drive voltage. The output voltage is clamped at 18V. An internal pulldown resistor is used to avoid a floating state of the gate before startup. By integrating circuits to control the slew rate of switch-on rise time, the external resistor RG may not be necessary to reduce switching noise, improving EMI performance. Structure Type A: Structure type A is sandwiching winding method. The power supply is mostly used sandwiching the secondary windings in between halves of the primary, especially when the output power is large. The auxiliary winding is at the top layer by increasing thickness between the primary winding. This course of action can reduce the leakage inductance and increase the coupling between the primary and the secondary winding. It can also improve the conversion efficiency and reduce the voltage spike on the MOSFET owing to transformer leakage inductance. However, it reflects the voltage spike on auxiliary winding easily and causes a large voltage deviation on VDD in light-load and heavy-load conditions. Structure Type B: Another kind of transformer structure is stacked winding method, usually used in the switching power supplies with smaller output power. This method produces worse coupling between primary and secondary winding than structure A; therefore, the voltage spike on the MOSFET is higher and the conversion efficiency is lower. Figure 20. Gate Drive Transformer Structure Figure 22 shows the modified structure of type A for sandwiching winding. The auxiliary and secondary windings are between halves of the primary windings. With this method, smaller voltage deviation on VDD in light load and heavy load can be achieved. Meanwhile, the output voltage OVP level is more precise. Therefore, the recommended transformer structure for the adaptor is shown as Figure 22. Leakage Inductance Effect Figure 21 shows the practical waveform on the MOSFET drain terminal. When the MOSFET turns off, a voltage spike (Vspike) is produced on the drain terminal owing to the transformer leakage inductance. The leak inductance is not easily calculable, but it can be minimized through the secondary windings between halves of the primary. Meanwhile, the voltage waveform on the auxiliary winding is similar to that on the MOSFET drain terminal. These spike voltages contribute extra energy to the VDD capacitor, which ruins the relationship between VDD voltage and the output voltage. Primary Winding Auxiliary Winding Secondary Winding (Insulated) Primary Winding Figure 22. Sandwiching Winding Structure Figure 21. MOSFET Drain Voltage Waveform © 2009 Fairchild Semiconductor Corporation Rev. 1.0.2 • 5/21/10 www.fairchildsemi.com 9 AN-6300 APPLICATION NOTE Lab Note Before modifying or soldering/desoldering the power supply, to discharge the primary capacitors through the external bleeding resistor. Otherwise, the PWM IC may be destroyed by external high-voltage during the process. This device is sensitive to electrostatic discharge (ESD). To improve the production yield, the production line should be ESD protected as required by ANSI ESD S1.1, ESD S1.4, ESD S7.1, ESD STM 12.1, and EOS/ESD S6.1 standards. Printed Circuit Board Layout Current/voltage/switching frequency make printed circuit board layout and design a very important issue. Good PCB layout minimizes excessive EMI and prevents the power supply from being disrupted during surge/ESD tests. Guidelines: To get better EMI performance and reduce line frequency ripples, the output of the bridge rectifier should be connected to capacitor Cbulk first, then to the switching circuits. The high-frequency current loop is found in Cbulk – Transformer – MOSFET – RS – Cbulk. The area enclosed by this current loop should be as small as possible. Keep the traces (especially 4→1) short, direct, and wide. High-voltage drain traces related the MOSFET and RCD snubber should be kept far way from control circuits to prevent unnecessary interference. If a heatsink is used for the MOSFET, ground the heatsink. As indicated by 3, the control circuits’ ground should be connected first, then to other circuitry. As indicated by 2, the area enclosed by the transformer auxiliary winding, D1, and C1 should also be kept small. Place C1 close to the FAN6300/A/H for good decoupling. Two suggestions with different pros and cons for ground connections are recommended: GND3→2→4→1: Possible method for circumventing the sense signals common impedance interference. GND3→2→1→4: Potentially better for ESD testing where a ground is not available for the power supply. The charges for ESD discharge path go from secondary through the transformer stray capacitance to the GND2 first. Then, the charges go from GND2 to GND1 and back to the mains. Control circuits should not be placed on the discharge path. Point discharge for common choke can decrease high-frequency impedance and help increase ESD immunity. Should a Y-cap between primary and secondary be required, the Y-cap should be connected to the positive terminal of the Cbulk (VDC). If this Y-cap is connected to the primary GND, it should be connected to the negative terminal of the Cbulk (GND1) directly. Point discharge of the Y-cap also helps with ESD. However, according to safety requirements, the creepage between the two pointed ends should be at least 5mm. Figure 23. Layout Considerations © 2009 Fairchild Semiconductor Corporation Rev. 1.0.2 • 5/21/10 www.fairchildsemi.com 10 AN-6300 APPLICATION NOTE Design Example This section shows a design example of 90W (19V/4.74A) adaptor using QR PWM controller FAN6300/A/H and boundary conduction mode PFC controller FAN6961. The PFC output voltage is 260V at low AC input voltage, 400V at high AC input voltage. From the specification, all critical components are treated and final measurement results are given. Based on the design guideline, the critical parameters are calculated and summarized as shown in Table 2. Table 2. Critical System Parameters Dmax 0.327 n 6.8 pk Ids,max 2.429A LP 700µH Vin,min 260V Vin,max 400V Vds,max 533.28V Vd 0.6V tf 0.6μs η 0.87 NP 34T NS 5T NAUX 4T Table 1. System Specification Input Input Voltage Range Line Frequency Range 90~264VAC 47~63Hz Output Output Voltage (Vo) Output Power (Po) Minimum Switching Frequency (fs,min) 19V 90W 50kHz L R10 C11 BD1 AC Input L1 D5 EMI Filter PFC STAGE C2 D6 C1 N + R2 D2 C7 C8 C9 R9 C10 Vo - D4 D3 R3 D1 C3 R1 IC1 FAN6300/A/H 8 HV R4 C4 6 VDD DET R5 R11 1 7 NC GATE 5 2 FB CS 3 R6 Q1 IC2 R12 C12 R14 R7 GND 4 IC3 C5 R13 R8 C6 C13 Figure 24. Complete Circuit Diagram © 2009 Fairchild Semiconductor Corporation Rev. 1.0.2 • 5/21/10 www.fairchildsemi.com 11 AN-6300 APPLICATION NOTE Table 3. Bill of Materials Part Value Note Resistor Part Value Note MOSFET R1 100k 1/4W Q1 FDP15N65 15A/650V R2 68k 2W Inductor R3 0Ω 1/4W L1 R4 180k 1/4W IC R5 27k 1/4W IC1 FAN6300/A/H R6 10Ω 1/4W IC2 PC817 R7 100Ω 1/4W IC3 TL431 R8 0.2Ω 2W Diode R9 47k 1/4W D1 0.5A/600V R10 33Ω 1/2W D2 BYV95C R11 220Ω 1/4W D3 FR103 R12 68k 1/4W D4 1N4148 R13 10k 1/4W D5 20A/100V Schottky Diode R14 1.6k 1/4W D6 20A/100V Schottky Diode BD1 4A/600V Bridge Diode 3µH Capacitor C1 68µF 450V C12 22nF C2 3.3nF 630V C13 222P/250V C3 47µF 50V C4 10µF 50V C5 470pF C6 47nF C7 1000µF 25V C8 470µF 25V C9 470µF 25V C10 470µF 25V C11 1nF 1kV © 2009 Fairchild Semiconductor Corporation Rev. 1.0.2 • 5/21/10 Y-Capacitor www.fairchildsemi.com 12 AN-6300 APPLICATION NOTE Related Datasheets FAN6300 — Highly Integrated Quasi-Resonant Current PWM Controller DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION, OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, or (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user. © 2009 Fairchild Semiconductor Corporation Rev. 1.0.2 • 5/21/10 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.fairchildsemi.com 13