IRF IRF2807S

PD - 94170
IRF2807S
IRF2807L
Advanced Process Technology
l Ultra Low On-Resistance
l Dynamic dv/dt Rating
l 175°C Operating Temperature
l Fast Switching
l Fully Avalanche Rated
Description
HEXFET® Power MOSFET
l
D
VDSS = 75V
RDS(on) = 13mΩ
G
S
Advanced HEXFET® Power MOSFETs from International
Rectifier utilize advanced processing techniques to achieve
extremely low on-resistance per silicon area. This benefit,
combined with the fast switching speed and ruggedized
device design that HEXFET power MOSFETs are well
known for, provides the designer with an extremely efficient
and reliable device for use in a wide variety of applications.
The D2Pak is a surface mount power package capable of
accommodating die sizes up to HEX-4. It provides the highest
power capability and the lowest possible on-resistance in any
existing surface mount package. The D2Pak is suitable for
high current applications because of its low internal connection
resistance and can dissipate up to 2.0W in a typical surface
mount application.
The through-hole version (IRF2807L) is available for lowprofile applications.
ID = 82A‡
D2Pak
IRF2807S
TO-262
IRF2807L
Absolute Maximum Ratings
Parameter
ID @ TC = 25°C
ID @ TC = 100°C
IDM
PD @TC = 25°C
VGS
IAR
EAR
dv/dt
TJ
TSTG
Continuous Drain Current, VGS @ 10V
Continuous Drain Current, VGS @ 10V
Pulsed Drain Current 
Power Dissipation
Linear Derating Factor
Gate-to-Source Voltage
Avalanche Current
Repetitive Avalanche Energy
Peak Diode Recovery dv/dt ƒ
Operating Junction and
Storage Temperature Range
Soldering Temperature, for 10 seconds
Mounting torque, 6-32 or M3 srew
Max.
82‡
Units
58
280
230
1.5
± 20
43
23
5.9
-55 to + 175
A
W
W/°C
V
A
mJ
V/ns
°C
300 (1.6mm from case )
10 lbf•in (1.1N•m)
Thermal Resistance
Parameter
RθJC
RθJA
www.irf.com
Junction-to-Case
Junction-to-Ambient (PCB mount)**
Typ.
Max.
Units
–––
–––
0.65
40
°C/W
1
02/14/02
IRF2807S/IRF2807L
Electrical Characteristics @ TJ = 25°C (unless otherwise specified)
RDS(on)
VGS(th)
gfs
Parameter
Drain-to-Source Breakdown Voltage
Breakdown Voltage Temp. Coefficient
Static Drain-to-Source On-Resistance
Gate Threshold Voltage
Forward Transconductance
Qg
Qgs
Qgd
td(on)
tr
td(off)
tf
Gate-to-Source Forward Leakage
Gate-to-Source Reverse Leakage
Total Gate Charge
Gate-to-Source Charge
Gate-to-Drain ("Miller") Charge
Turn-On Delay Time
Rise Time
Turn-Off Delay Time
Fall Time
Min.
75
–––
–––
2.0
38
–––
–––
–––
–––
–––
–––
–––
–––
–––
–––
–––
IDSS
Drain-to-Source Leakage Current
LD
Internal Drain Inductance
–––
LS
Internal Source Inductance
–––
Ciss
Coss
Crss
EAS
Input Capacitance
Output Capacitance
Reverse Transfer Capacitance
Single Pulse Avalanche Energy‚
–––
–––
–––
–––
V(BR)DSS
∆V(BR)DSS/∆TJ
IGSS
Typ.
–––
0.074
–––
–––
–––
–––
–––
–––
–––
–––
–––
–––
13
64
49
48
Max. Units
Conditions
–––
V
VGS = 0V, ID = 250µA
––– V/°C Reference to 25°C, ID = 1mA
13
mΩ VGS = 10V, ID = 43A „
4.0
V
VDS = VGS, ID = 250µA
–––
S
VDS = 50V, ID = 43A„
25
VDS = 75V, VGS = 0V
µA
250
VDS = 60V, VGS = 0V, TJ = 150°C
100
VGS = 20V
nA
-100
VGS = -20V
160
ID = 43A
29
nC
VDS = 60V
55
VGS = 10V, See Fig. 6 and 13
–––
VDD = 38V
–––
ID = 43A
ns
–––
RG = 2.5Ω
–––
VGS = 10V, See Fig. 10 „
Between lead,
4.5 –––
6mm (0.25in.)
nH
G
from package
7.5 –––
and center of die contact
3820 –––
VGS = 0V
610 –––
VDS = 25V
130 –––
pF
ƒ = 1.0MHz, See Fig. 5
1280…340† mJ IAS = 50A, L = 370µH
D
S
Source-Drain Ratings and Characteristics
IS
ISM
VSD
trr
Qrr
ton
Parameter
Continuous Source Current
(Body Diode)
Pulsed Source Current
(Body Diode)
Diode Forward Voltage
Reverse Recovery Time
Reverse Recovery Charge
Forward Turn-On Time
Min. Typ. Max. Units
Conditions
D
MOSFET symbol
––– ––– 82‡
showing the
A
G
integral reverse
––– ––– 280
S
p-n junction diode.
––– ––– 1.2
V
TJ = 25°C, IS = 43A, VGS = 0V „
––– 100 150
ns
TJ = 25°C, IF = 43A
––– 410 610
nC
di/dt = 100A/µs „
Intrinsic turn-on time is negligible (turn-on is dominated by LS+LD)
Notes:
 Repetitive rating; pulse width limited by
max. junction temperature. (See fig. 11)
‚ Starting TJ = 25°C, L = 370µH
RG = 25Ω, IAS = 43A, VGS=10V (See Figure 12)
ƒ ISD ≤ 43A, di/dt ≤ 300A/µs, VDD ≤ V(BR)DSS,
TJ ≤ 175°C
„ Pulse width ≤ 400µs; duty cycle ≤ 2%.
2
… This is a typical value at device destruction and represents
operation outside rated limits.
† This is a calculated value limited to TJ = 175°C .
‡ Calculated continuous current based on maximum allowable
junction temperature. Package limitation current is 75A.
**When mounted on 1" square PCB (FR-4 or G-10 Material). For
recommended footprint and soldering techniques refer to application
note #AN-994
www.irf.com
IRF2807S/IRF2807L
1000
1000
VGS
15V
10V
8.0V
7.0V
6.0V
5.5V
5.0V
BOTTOM 4.5V
VGS
15V
10V
8.0V
7.0V
6.0V
5.5V
5.0V
BOTTOM 4.5V
TOP
I D , Drain-to-Source Current (A)
I D , Drain-to-Source Current (A)
TOP
100
100
4.5V
20µs PULSE WIDTH
T = 25 C
°
J
10
0.1
1
10
4.5V
100
Fig 1. Typical Output Characteristics
TJ = 25 ° C
TJ = 175 ° C
100
V DS = 25V
20µs PULSE WIDTH
6.0
7.0
8.0
Fig 3. Typical Transfer Characteristics
www.irf.com
9.0
RDS(on) , Drain-to-Source On Resistance
(Normalized)
I D , Drain-to-Source Current (A)
3.0
5.0
1
10
100
Fig 2. Typical Output Characteristics
1000
VGS , Gate-to-Source Voltage (V)
°
J
VDS , Drain-to-Source Voltage (V)
VDS , Drain-to-Source Voltage (V)
10
4.0
20µs PULSE WIDTH
T = 175 C
10
0.1
ID = 71A
2.5
2.0
1.5
1.0
0.5
0.0
-60 -40 -20
VGS = 10V
0
20 40 60 80 100 120 140 160 180
TJ , Junction Temperature ( °C)
Fig 4. Normalized On-Resistance
Vs. Temperature
3
IRF2807S/IRF2807L
VGS = 0V,
f = 1 MHZ
Ciss = Cgs + Cgd , Cds SHORTED
Crss = Cgd
C, Capacitance(pF)
6000
Coss = Cds + Cgd
5000
Ciss
4000
3000
Coss
2000
Crss
1000
VGS , Gate-to-Source Voltage (V)
20
7000
0
ID = 43A
16
12
8
4
FOR TEST CIRCUIT
SEE FIGURE 13
0
1
10
0
100
80
120
160
Fig 6. Typical Gate Charge Vs.
Gate-to-Source Voltage
Fig 5. Typical Capacitance Vs.
Drain-to-Source Voltage
1000
1000
OPERATION IN THIS AREA
LIMITED BY R DS (on)
ID , Drain-to-Source Current (A)
ISD , Reverse Drain Current (A)
40
Q G , Total Gate Charge (nC)
VDS , Drain-to-Source Voltage (V)
100
TJ = 175 ° C
100
10
TJ = 25 ° C
1
0.1
0.0
V GS = 0 V
0.4
0.8
1.2
1.6
2.0
VSD ,Source-to-Drain Voltage (V)
Fig 7. Typical Source-Drain Diode
Forward Voltage
4
VDS = 60V
VDS = 37V
VDS = 15V
2.4
100µsec
10
1msec
Tc = 25°C
Tj = 175°C
Single Pulse
1
1
10msec
10
100
1000
VDS , Drain-toSource Voltage (V)
Fig 8. Maximum Safe Operating Area
www.irf.com
IRF2807S/IRF2807L
100
LIMITED BY PACKAGE
VDS
VGS
I D , Drain Current (A)
80
RD
D.U.T.
RG
+
-VDD
60
VGS
Pulse Width ≤ 1 µs
Duty Factor ≤ 0.1 %
40
Fig 10a. Switching Time Test Circuit
20
VDS
90%
0
25
50
75
100
125
TC , Case Temperature
150
175
( °C)
10%
VGS
Fig 9. Maximum Drain Current Vs.
Case Temperature
td(on)
tr
t d(off)
tf
Fig 10b. Switching Time Waveforms
Thermal Response (Z thJC )
1
D = 0.50
0.20
0.1
0.10
P DM
0.05
0.02
0.01
t1
SINGLE PULSE
(THERMAL RESPONSE)
t2
Notes:
1. Duty factor D = t 1 / t 2
2. Peak T J = P DM x Z thJC + TC
0.01
0.00001
0.0001
0.001
0.01
0.1
t1 , Rectangular Pulse Duration (sec)
Fig 11. Maximum Effective Transient Thermal Impedance, Junction-to-Case
www.irf.com
5
IRF2807S/IRF2807L
L
VD S
D .U .T
RG
IA S
2V0GS
V
tp
D R IV E R
+
- VD D
A
0 .0 1 Ω
Fig 12a. Unclamped Inductive Test Circuit
V (B R )D SS
tp
EAS , Single Pulse Avalanche Energy (mJ)
600
1 5V
ID
18A
30A
43A
TOP
500
BOTTOM
400
300
200
100
0
25
50
75
100
125
150
175
Starting TJ , Junction Temperature ( °C)
Fig 12c. Maximum Avalanche Energy
Vs. Drain Current
IAS
Fig 12b. Unclamped Inductive Waveforms
Current Regulator
Same Type as D.U.T.
50KΩ
QG
12V
.2µF
.3µF
VGS
QGS
D.U.T.
QGD
+
V
- DS
VGS
VG
3mA
IG
Charge
Fig 13a. Basic Gate Charge Waveform
6
ID
Current Sampling Resistors
Fig 13b. Gate Charge Test Circuit
www.irf.com
IRF2807S/IRF2807L
Peak Diode Recovery dv/dt Test Circuit
+
D.U.T*
ƒ
Circuit Layout Considerations
• Low Stray Inductance
• Ground Plane
• Low Leakage Inductance
Current Transformer
+
‚
-
-
„
+

• dv/dt controlled by RG
• ISD controlled by Duty Factor "D"
• D.U.T. - Device Under Test
RG
VGS
*
+
-
VDD
Reverse Polarity of D.U.T for P-Channel
Driver Gate Drive
P.W.
Period
D=
P.W.
Period
[VGS=10V ] ***
D.U.T. ISD Waveform
Reverse
Recovery
Current
Body Diode Forward
Current
di/dt
D.U.T. VDS Waveform
Diode Recovery
dv/dt
Re-Applied
Voltage
Body Diode
[VDD]
Forward Drop
Inductor Curent
Ripple ≤ 5%
[ ISD ]
*** VGS = 5.0V for Logic Level and 3V Drive Devices
Fig 14. For N-channel HEXFET® power MOSFETs
www.irf.com
7
IRF2807S/IRF2807L
D2Pak Package Outline
1 0.54 (.415 )
1 0.29 (.405 )
1.4 0 (.055 )
M AX.
-A-
1.3 2 (.05 2)
1.2 2 (.04 8)
2
1.7 8 (.07 0)
1.2 7 (.05 0)
1
10 .1 6 (.4 00 )
R E F.
-B-
4 .6 9 (.18 5)
4 .2 0 (.16 5)
6.47 (.2 55 )
6.18 (.2 43 )
1 5.49 (.6 10)
1 4.73 (.5 80)
3
2.7 9 (.110 )
2.2 9 (.090 )
2.61 (.1 03 )
2.32 (.0 91 )
5.28 (.2 08 )
4.78 (.1 88 )
3X
1.40 (.0 55)
1.14 (.0 45)
3X
5 .08 (.20 0)
0.55 (.0 22)
0.46 (.0 18)
0.9 3 (.0 37 )
0.6 9 (.0 27 )
0.25 (.0 10 )
M
8.8 9 (.3 50 )
R E F.
1.3 9 (.0 55 )
1.1 4 (.0 45 )
B A M
M IN IM U M R EC O M M E ND E D F O O TP R IN T
1 1.43 (.4 50 )
NO TE S:
1 D IM EN S IO N S A FTER SO LD E R D IP .
2 D IM EN S IO N IN G & TO LE R AN C IN G P ER AN S I Y1 4.5M , 19 82 .
3 C O N TRO L LIN G D IM EN S IO N : IN C H.
4 H E ATSINK & L EA D D IM E N SIO N S DO N O T IN C LU D E B U R RS .
LE AD AS SIG N M E N TS
1 - G ATE
2 - D RA IN
3 - SO U R C E
8 .89 (.35 0)
17 .78 (.70 0)
3.81 (.1 5 0)
2.0 8 (.08 2)
2X
2.5 4 (.100 )
2X
D2Pak Part Marking Information
IN TE R N A TIO N A L
R E C T IF IE R
LO G O
A S S E M B LY
LO T C O D E
8
A
PART NUM BER
F530S
9 24 6
9B
1M
DATE CODE
(Y YW W )
YY = Y E A R
W W = W EEK
www.irf.com
IRF2807S/IRF2807L
TO-262 Package Outline
TO-262 Part Marking Information
www.irf.com
9
IRF2807S/IRF2807L
D2Pak Tape & Reel Information
TR R
1 .6 0 (.0 6 3 )
1 .5 0 (.0 5 9 )
4 .1 0 ( .1 6 1 )
3 .9 0 ( .1 5 3 )
F E E D D IR E C TIO N 1 .8 5 ( .0 7 3 )
1 .6 5 ( .0 6 5 )
1 .6 0 (.0 6 3 )
1 .5 0 (.0 5 9 )
1 1.6 0 (.4 57 )
1 1.4 0 (.4 49 )
0.3 6 8 (.01 4 5 )
0.3 4 2 (.01 3 5 )
1 5 .42 (.60 9 )
1 5 .22 (.60 1 )
2 4 .3 0 (.9 5 7 )
2 3 .9 0 (.9 4 1 )
TRL
1 0.9 0 (.4 2 9)
1 0.7 0 (.4 2 1)
1 .75 (.06 9 )
1 .25 (.04 9 )
4 .7 2 (.1 3 6)
4 .5 2 (.1 7 8)
16 .1 0 (.63 4 )
15 .9 0 (.62 6 )
F E E D D IR E C T IO N
13.50 (.532 )
12.80 (.504 )
2 7.4 0 (1.079 )
2 3.9 0 (.9 41)
4
3 30 .00
( 14.1 73 )
MAX.
6 0.0 0 (2.36 2)
M IN .
N O TE S :
1 . CO M F OR M S TO E IA -418 .
2 . CO N TR O L LIN G D IM E N SIO N : M IL LIM E T ER .
3 . DIM E NS IO N M EA S UR E D @ H U B.
4 . IN C LU D ES FL AN G E DIST O R T IO N @ O UT E R E D G E.
26 .40 (1 .03 9)
24 .40 (.9 61 )
3
30.4 0 (1.19 7)
M A X.
4
Data and specifications subject to change without notice.
This product has been designed and qualified for the Industrial market.
Qualification Standards can be found on IR’s Web site.
IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105
TAC Fax: (310) 252-7903
Visit us at www.irf.com for sales contact information. 02/02
10
www.irf.com
Note: For the most current drawings please refer to the IR website at:
http://www.irf.com/package/