TB62600F TOSHIBA Bi−CMOS INTEGRATED CIRCUIT SILICON MONOLITHIC TB62600F 64BIT SHIFT REGISTER / LATCH DRIVER The TB62600F is specifically designed for 64bit Thermal Head drivers. And this IC is monolithic integrated circuits designed to be used together with Bi−CMOS (DMOS) integrated circuit. The devices consist of a 64bit shift register, dual 64bit latches, and 64 output DMOS structures. FEATURE Built−in selection circuit : parallel−in parallel−out (8 × 8) or serial−in parallel−out (1 × 64) CMOS compatible inputs Weight: 1.6 g (typ.) Open−drain DMOS outputs Low steady−state power consumption Built−in mono stable multi−viblator for head protection Package : QFP100−P−1420C 1 2006-06-14 TB62600F PIN CONNECTION (TOP VIEW) 2 2006-06-14 TB62600F BLOCK DIAGRAM 3 2006-06-14 TB62600F BLOCK DIAGRAM (8 × 8, 1 × 64 shift register) 4 2006-06-14 TB62600F TIMING WAVEFORM 5 2006-06-14 TB62600F TERMINAL DESCRIPTION PIN NAME PIN No. FUNCTION CLOCK 97 Input Terminals for Shift register Clock. ENABLE 84 "L" : All Outputs "On". Pull−Down Input Terminal. RESET 98 "L" : Reset shift register and latch. Pull−Down Input Terminal. D0~D7 88~95 MMV−C/R 78 CR Connection Terminal for CR Timer (MMV) MMV−OUT 79 Output Terminal for CR Timer (MMV) OUT0 ~ 63 ― Output Terminals. These are Open Drain Outputs. SELECT 83 Input Terminal for Input Mode Data. "H" : 8bit Parallel Input Mode, "L" : 1bit Serial Input Mode. S−OUT 96 Output Terminal for Serial Data "D63". LATCH1 / LATCH2 86 / 85 Input Terminal for Latch. "H" : Data Throught, "L" : Data Latch. Input Terminals for Output Data. "H" : Output On, "L" : Output Off. VDD 81, 100 Supply Voltage Terminal for Control Logic. L−GND 82, 99 Ground Terminal for Control Logic P−GND ― Ground Terminal for Drivers. 10 Terminals. 6 2006-06-14 TB62600F MMV OPERATION MMV Output of Q becomes "L" when the MMV / E voltage becomes less than Vref (L) after the first rising edge of Internal Clock. And becomes "H" when the MMV / E voltage above Vref (H) after re−changing of external capacitance connect to MMV / E. The external capacitance and resistor connect to MMV / E control MMV Output "ON" period. So Output Load is protected from burn−out. It's required enough discharging time (decided by Time period of Internal Clock) of external capacitance. (Refer to figure below) PULSE WIDTH OF MMV See Below 7 2006-06-14 TB62600F ABSOLUTE MAXIMUM RATINGS (Ta = 25°C) CHARACTERISTIC SYMBOL RATING UNIT Supply Voltage VDD −0.3~7.0 V Output Drain−Source Voltage VDS −0.4~30 V Output Current IDS 130 mA / ch Input Current IIN ±5 mA Input Voltage VIN −0.3~VDD ± 0.3 V Free Air Power Dissipation (Note 1) PCB 1.0 PD W 1.3 Operating Temperature Topr −40~85 °C Storage Temperature Tstg −55~150 °C Note 1: 60 × 60 × 1.6 mm Cu 24% Glass Epoxy PCB RECOMMENDED OPERATING CONDITIONS (Ta = −40~85°C, VSS = 0 V) CHARACTERISTIC SYMBOL CONDITION MIN TYP. MAX UNIT VDD ― 4.5 5 5.5 V "H" LEVEL VIH ― 0.7 VDD ― VDD "L" LEVEL VIL ― 0 ― 0.3 VDD Supply Voltage Input Voltage Output Drain−Source Voltage VOUT ― Duty = 100% Output Current IOUT Duty = 80% All Output "L" Level Duty = 50% ― ― 24 ― ― 44 ― ― 49 ― ― 62 V V mA / ch External Resistor REXT ― 200 ― 1000 kΩ External Capacitance CEXT ― 100 ― 4000 pF PD ― ― ― 0.67 mW Power Dissipation 8 2006-06-14 TB62600F ELECTRICAL CHARACTERISTICS (Ta = −10~80°C, VDD = 4.5~5.5 V, VSS = 0 V, "H" = VIH, "L" =VIL) CHARACTERISTIC SYMBOL TEST CIR− CUIT VDS1 ― VDS1 VDS2 MIN TYP. MAX IOUT = 40 mA, Ta = 25°C ― 0.16 0.32 ― IOUT = 40 mA ― ― 0.48 ― IOUT = 100 mA, Ta = 25°C ― 0.40 0.80 VDS2 ― IOUT = 100 mA ― ― 1.20 "H" Level IOH ― VOH = 4.6 V Ta =25°C ― 0.2 0.5 "L" Level IOL ― VOH = 0.4 V Ta=25°C ― 0.2 0.5 RON ― Ta = 25°C ― 4.00 8.00 IOZ1 ― VOUT = 30V, EN = "L", 1bit ― ― 10 IOZ2 ― VOUT = 30V, EN = "L", 64bit ― ― 100 IIN ― VIN = VDD or VSS ― ― ±1 "H" Level VIH ― ― 0.7 VDD ― ― "L" Level VIL ― ― 0 ― 0.3 VDD Voltage Superviser Operating Voltage VVS ― ― 2.0 ― 4.0 V Supply Current IDD ― ― ― ― 300 µA IDD1 ― fCLK = 5MHz, Duty = 50% Data = 1 / 2 fCLK, OUTPUT off LATCH = "L", LATCH −Data = "L" ― ― 5.0 IDD2 ― fCLK = 1MHz, Duty = 50% Data=1 / 64 fCLK All OUTPUT open LATCH = "H", 1bit ON ― ― 6.0 Input Pull−Up Resistor RVDD ― VDD = 5.0 V, Ta = 25°C 150 300 600 Input Pull−Down Resistor RVSS ― VDD = 5.0 V, Ta = 25°C 150 300 600 Internal Clock Frequency fint ― VDD = 5.0 V, Ta = 25°C 400 800 ― Output Voltage "L" Level Output Current Output Resistor Output Leakage Current Input Current TEST CONDITION S−OUT MMV−OUT Input Voltage Operating Supply Current 9 UNIT V mA Ω µA µA V mA kΩ kHz 2006-06-14 TB62600F RECOMMENDED TIMING CONDITIONS (Ta = −40~85°C, VDD = 4.5~5.5 V, VSS = 0 V) CHARACTERISTIC SYMBOL TEST CONDITION MIN TYP. MAX UNIT Clock Pulse Width tw CLK ― 50 ― ― ns Enable Pulse Width tw EN ― 0.5 ― ― µs Latch Pulse Width tw LAT ― 50 ― ― ns Clear Pulse Width tw CLR ― 80 ― ― ns Data Set up Time tsetup ― 37 50 ― ns Data Hold Time thold ― 50 ― ― ns MIN TYP. MAX UNIT MMV−C / R = "L" ― ― 1000 R − Outn MMV−C / R = "L" ― ― 1000 LAT1 − Outn MMV−C / R = "L" ― ― 1000 LAT2 − Outn MMV−C / R = "L" ― ― 1000 EN− Outn R = 750 kΩ, C = 2600 pF,Ta = 25°C ― ― 2500 CLK− Outn MMV−C / R = "L" ― ― 1000 LAT1 − Outn MMV−C / R = "L" ― ― 1000 MMV−C / R = "L" ― ― 1000 R = 750 kΩ, C = 2600 pF,Ta = 25°C ― ― 2500 SWITCHING CHARACTERISTICS (Ta = 25°C, VDD = 5 V, VOUT = 26 V, R1 = 650 Ω, CL = 15 pF) CHARACTERISTIC SYMBOL CLK− Outn Propagation Delay Time (Low−to−High) Propagation Delay Time (High−to−Low) LAT2 − Outn tpLH tpHL EN− Outn Set Up Time Hold Time TEST CONDITION ns ns CLK− LATn tsetup (L) ― ― 70 120 CLK−S−IN tsetup (D) ― ― ― 30 CLK− LATn thold (L) ― ― ― 0 CLK−S−IN thold (D) ― ― ― 20 tw CLK ― ― ― 50 ns ― ― ― 50 ns Clock Pulse Width Latch Pulse Width tw LATn ns Reset Pulse Width tw R ― ― ― 50 ns Enable Pulse Width tw EN ― ― ― 400 ns ― 200 500 ns ns Output Rise Time tor OUTn OUTn ― 200 500 Maximum Clock Frequency fMAX Duty = 50% 10 15 ― Voltage Superviser Operating Pulse Width tw VS VDD (H) = 5 V, VDD (L) = 2 V ― 200 ― MMV Reset Time tMMV R = 750 kΩ, C = 2600 pF,Ta = 25°C 1 3 5 Output Fall Time tof 10 2006-06-14 TB62600F EQUIVALENT OF INPUTS AND OUTPUT CIRCUIT 1. CLOCK, SELECT 2. ENABLE, LATCH1, LATCH2 , RESET ,D0~7 3. OUTn 4. MMV−C / R 5. S−OUT, MMV−OUT PRECAUTIONS for USING This IC does not integrate protection circuits such as overcurrent and overvoltage protectors. Thus, if excess current or voltage is applied to the IC, the IC may be damaged. Please design the IC so that excess current or voltage will not be applied to the IC. Utmost care is necessary in the design of the output line, VCC (VDD) and GND (L−GND, P−GND) line since IC may be destroyed due to short−circuit between outputs, air contamination fault, or fault by improper grounding. 11 2006-06-14 TB62600F PACKAGE DIMENSIONS QFP100−P−1420−0.65C Unit: mm Weight: 1.6 g (typ.) 12 2006-06-14 TB62600F Notes on Contents 1. Block Diagrams Some of the functional blocks, circuits, or constants in the block diagram may be omitted or simplified for explanatory purposes. 2. Equivalent Circuits The equivalent circuit diagrams may be simplified or some parts of them may be omitted for explanatory purposes. 3. Timing Charts Timing charts may be simplified for explanatory purposes. IC Usage Considerations Notes on Handling of ICs (1) The absolute maximum ratings of a semiconductor device are a set of ratings that must not be exceeded, even for a moment. Do not exceed any of these ratings. Exceeding the rating(s) may cause the device breakdown, damage or deterioration, and may result injury by explosion or combustion. (2) Use an appropriate power supply fuse to ensure that a large current does not continuously flow in case of over current and/or IC failure. The IC will fully break down when used under conditions that exceed its absolute maximum ratings, when the wiring is routed improperly or when an abnormal pulse noise occurs from the wiring or load, causing a large current to continuously flow and the breakdown can lead smoke or ignition. To minimize the effects of the flow of a large current in case of breakdown, appropriate settings, such as fuse capacity, fusing time and insertion circuit location, are required. (3) If your design includes an inductive load such as a motor coil, incorporate a protection circuit into the design to prevent device malfunction or breakdown caused by the current resulting from the inrush current at power ON or the negative current resulting from the back electromotive force at power OFF. IC breakdown may cause injury, smoke or ignition. Use a stable power supply with ICs with built-in protection functions. If the power supply is unstable, the protection function may not operate, causing IC breakdown. IC breakdown may cause injury, smoke or ignition. (4) Do not insert devices in the wrong orientation or incorrectly. Make sure that the positive and negative terminals of power supplies are connected properly. Otherwise, the current or power consumption may exceed the absolute maximum rating, and exceeding the rating(s) may cause the device breakdown, damage or deterioration, and may result injury by explosion or combustion. In addition, do not use any device that is applied the current with inserting in the wrong orientation or incorrectly even just one time. (5) Carefully select external components (such as inputs and negative feedback capacitors) and load components (such as speakers), for example, power amp and regulator. If there is a large amount of leakage current such as input or negative feedback condenser, the IC output DC voltage will increase. If this output voltage is connected to a speaker with low input withstand voltage, overcurrent or IC failure can cause smoke or ignition. (The over current can cause smoke or ignition from the IC itself.) In particular, please pay attention when using a Bridge Tied Load (BTL) connection type IC that inputs output DC voltage to a speaker directly. 13 2006-06-14 TB62600F Points to Remember on Handling of ICs (1) Heat Radiation Design In using an IC with large current flow such as power amp, regulator or driver, please design the device so that heat is appropriately radiated, not to exceed the specified junction temperature (Tj) at any time and condition. These ICs generate heat even during normal use. An inadequate IC heat radiation design can lead to decrease in IC life, deterioration of IC characteristics or IC breakdown. In addition, please design the device taking into considerate the effect of IC heat radiation with peripheral components. (2) Back-EMF When a motor rotates in the reverse direction, stops or slows down abruptly, a current flow back to the motor’s power supply due to the effect of back-EMF. If the current sink capability of the power supply is small, the device’s motor power supply and output pins might be exposed to conditions beyond maximum ratings. To avoid this problem, take the effect of back-EMF into consideration in system design. 14 2006-06-14 TB62600F RESTRICTIONS ON PRODUCT USE 060116EBA • The information contained herein is subject to change without notice. 021023_D • TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc. 021023_A • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc. Unintended Usage of TOSHIBA products listed in this document shall be made at the customer’s own risk. 021023_B • The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. 060106_Q • The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of TOSHIBA or others. 021023_C • The products described in this document are subject to the foreign exchange and foreign trade laws. 021023_E 15 2006-06-14