STB13NK60ZT4, STP13NK60Z STP13NK60ZFP, STW13NK60Z N-channel 600 V, 0.48 Ω, 13 A, TO-220, TO-220FP, D2PAK TO-247 Zener-protected SuperMESH™ Power MOSFET Features Type VDSS RDS(on) max ID Pw STB13NK60ZT4 STP13NK60ZFP STP13NK60Z STW13NK60Z 600 V 600 V 600 V 600 V <0.55 Ω <0.55 Ω <0.55 Ω <0.55 Ω 13 A 13 A 13 A 13 A 150 W 35 W 150 W 150 W ■ Gate charge minimized ■ Very low intrinsic capacitances ■ 3 3 1 TO-247 D²PAK 3 3 1 Very good manufacturing repeatability TO-220 Application ■ 2 1 Figure 1. 2 1 2 TO-220FP Internal schematic diagram Switching applications Description The SuperMESH™ series is obtained through an extreme optimization of ST’s well established strip-based PowerMESH™ layout. In addition to pushing on-resistance significantly down, special care is taken to ensure a very good dv/dt capability for the most demanding applications. Table 1. Device summary Order codes Marking Package Packaging STB13NK60ZT4 B13NK60Z D²PAK Tape and reel STP13NK60ZFP P13NK60ZFP TO-220FP Tube STP13NK60Z P13NK60Z TO-220 Tube STW13NK60Z W13NK60Z TO-247 Tube April 2009 Doc ID 8527 Rev 7 1/18 www.st.com 18 Contents STB13NK60ZT4, STx13NK60Z, STP13NK60ZFP Contents 1 Electrical ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2.1 Electrical characteristics (curves) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 3 Test circuits 4 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 5 Packing mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 6 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 2/18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Doc ID 8527 Rev 7 STB13NK60ZT4, STx13NK60Z, STP13NK60ZFP 1 Electrical ratings Electrical ratings Table 2. Absolute maximum ratings Value Symbol Parameter TO-220 / TO-247 D²PAK Unit TO-220FP VDS Drain-source voltage (VGS = 0) 600 V VGS Gate-source voltage ± 30 V ID Drain current (continuous) at TC = 25 °C 13 13 (1) A ID Drain current (continuous) at TC = 100 °C 8.2 8.2 (1) A IDM (2) Drain current (pulsed) 52 52(1) A PTOT Total dissipation at TC = 25 °C 150 35 W Derating factor 1.20 0.27 W/°C Vesd(G-S) G-S ESD (HBM C=100pF, R=1.5 kΩ) dv/dt (3) VISO Tj Tstg Peak diode recovery voltage slope Insulation withstand voltage (AC) 4000 V 4.5 V/ns -- Operating junction temperature Storage temperature 2500 -55 to 150 V °C 1. Limited only by maximum temperature allowed 2. Pulse width limited by safe operating area 3. ISD ≤ 13 A, di/dt ≤ 200 A/µs, VDD ≤ V(BR)DSS, TJ ≤ TJMAX Table 3. Thermal data Value Symbol Parameter TO-220 TO-247 Rthj-case Thermal resistance junction-case max Rthj-pcb (1) Thermal resistance junction-pcb max Rthj-amb Tl Unit D²PAK 0.83 -- 60 TO-220FP 3.6 °C/W -- °C/W Thermal resistance junction-amb max 62.5 °C/W Maximum lead temperature for soldering purpose 300 °C 1. When mounted on minimum footprint Doc ID 8527 Rev 7 3/18 Electrical ratings Table 4. 4/18 STB13NK60ZT4, STx13NK60Z, STP13NK60ZFP Avalanche characteristics Symbol Parameter Max value Unit IAR Avalanche current, repetitive or notrepetitive (pulse width limited by Tj max) 10 A EAS Single pulse avalanche energy (starting Tj=25 °C, ID=IAR, VDD= 50 V) 400 mJ Doc ID 8527 Rev 7 STB13NK60ZT4, STx13NK60Z, STP13NK60ZFP 2 Electrical characteristics Electrical characteristics (TCASE = 25 °C unless otherwise specified) Figure 2. Symbol V(BR)DSS On/off states Parameter Test conditions Drain-source breakdown voltage ID = 1 mA, VGS= 0 Min. Typ. Max. 600 Unit V VDS = Max rating, VDS = Max rating,Tc=125 °C 1 50 µA µA Gate body leakage current (VDS = 0) VGS = ±20 V ±10 µA VGS(th) Gate threshold voltage VDS= VGS , ID = 100 µA 3.75 4.5 V RDS(on) Static drain-source on resistance VGS= 10 V, ID= 4.5 A 0.48 0.55 Ω Min. Typ. Max. Unit IDSS Zero gate voltage drain current (VGS = 0) IGSS Table 5. Symbol gfs (1) Ciss Coss Crss Coss eq.(2) Qg Qgs Qgd 3 Dynamic Parameter Test conditions Forward transconductance VDS =8 V, ID = 5 A - 11 S Input capacitance Output capacitance Reverse transfer capacitance VDS =25 V, f=1 MHz, VGS=0 - 2030 210 48 pF pF pF Equivalent output capacitance VGS=0, VDS =0 to 480 V - 125 pF - 66 11 33 Total gate charge Gate-source charge Gate-drain charge VDD=480 V, ID = 10 A VGS =10 V (see Figure 21) 92 nC nC nC 1. Pulsed: pulse duration = 300µs, duty cycle 1.5% 2. Coss eq. is defined as a constant equivalent capacitance giving the same charging time as Coss when VDS increases from 0 to 80% VDSS Doc ID 8527 Rev 7 5/18 Electrical characteristics Table 6. Symbol STB13NK60ZT4, STx13NK60Z, STP13NK60ZFP Switching times Parameter Test conditions Min. Typ. Max. Unit td(on) tr Turn-on delay time Rise time VDD= 300 V, ID= 5 A, RG=4.7 Ω, VGS=10 V (see Figure 20) - 22 14 - ns ns td(off) tf Turn-off delay time Fall time VDD=300 V, ID= 5 A, RG=4.7 Ω, VGS=10 V (see Figure 20) - 61 12 - ns ns tr(Voff) tf tc Off-voltage rise time Fall time Cross-over time VDD=480 V, ID= 10 A, RG=4.7 Ω, VGS=10 V (see Figure 20) - 10 9 20 - ns ns ns Table 7. Symbol BVGSO Gate-source Zener diode Parameter Test conditions Gate-source breakdown voltage Igs=±1mA (open drain) Min. Typ. Max. Unit 30 - - V The built-in back-to-back Zener diodes have specifically been designed to enhance not only the device’s ESD capability, but also to make them safely absorb possible voltage transients that may occasionally be applied from gate to source. In this respect the Zener voltage is appropriate to achieve an efficient and cost-effective intervention to protect the device’s integrity. These integrated Zener diodes thus avoid the usage of external components. Table 8. Symbol ISD ISDM (1) VSD (2) trr Qrr IRRM Source drain diode Parameter Test conditions Source-drain current Source-drain current (pulsed) Forward on voltage ISD = 10 A, VGS=0 Reverse recovery time Reverse recovery charge Reverse recovery current ISD= 10 A, di/dt = 100 A/µs, VDD=35 V, Tj=150 °C 1. Pulse width limited by safe operating area 2. Pulsed: pulse duration = 300µs, duty cycle 1.5% 6/18 Doc ID 8527 Rev 7 Min. Max. Unit - 10 40 A A - 1.6 V - Typ. 570 4.5 16 ns µC A STB13NK60ZT4, STx13NK60Z, STP13NK60ZFP Electrical characteristics 2.1 Electrical characteristics (curves) Figure 3. Safe operating area for TO-220/ D²PAK Figure 4. Thermal impedance for TO-220/ D²PAK Figure 5. Safe operating area for TO-220FP Figure 6. Thermal impedance for TO-220FP Figure 7. Safe operating area for TO-247 Figure 8. Thermal impedance for TO-247 Doc ID 8527 Rev 7 7/18 Electrical characteristics Figure 9. Output characteristics Figure 11. Transconductance STB13NK60ZT4, STx13NK60Z, STP13NK60ZFP Figure 10. Transfer characteristics Figure 12. Static drain-source on resistance Figure 13. Gate charge vs gate-source voltage Figure 14. Capacitance variations 8/18 Doc ID 8527 Rev 7 STB13NK60ZT4, STx13NK60Z, STP13NK60ZFP Electrical characteristics Figure 15. Normalized gate threshold voltage vs temperature Figure 16. Normalized on resistance vs temperature Figure 17. Source-drain diode forward characteristics Figure 18. Normalized BVDSS vs temperature Figure 19. Maximum avalanche energy vs temperature Doc ID 8527 Rev 7 9/18 Test circuits 3 STB13NK60ZT4, STx13NK60Z, STP13NK60ZFP Test circuits Figure 20. Switching times test circuit for resistive load Figure 21. Gate charge test circuit Figure 22. Test circuit for inductive load Figure 23. Unclamped inductive load test switching and diode recovery times circuit Figure 24. Unclamped inductive waveform 10/18 Figure 25. Switching time waveform Doc ID 8527 Rev 7 STB13NK60ZT4, STx13NK60Z, STP13NK60ZFP 4 Package mechanical data Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK is an ST trademark. Doc ID 8527 Rev 7 11/18 Package mechanical data STB13NK60ZT4, STx13NK60Z, STP13NK60ZFP TO-220 mechanical data mm inch Dim Min A b b1 c D D1 E e e1 F H1 J1 L L1 L20 L30 ∅P Q 12/18 Typ 4.40 0.61 1.14 0.49 15.25 Max Min 4.60 0.88 1.70 0.70 15.75 0.173 0.024 0.044 0.019 0.6 10.40 2.70 5.15 1.32 6.60 2.72 14 3.93 0.393 0.094 0.194 0.048 0.244 0.094 0.511 0.137 1.27 10 2.40 4.95 1.23 6.20 2.40 13 3.50 0.181 0.034 0.066 0.027 0.62 0.409 0.106 0.202 0.051 0.256 0.107 0.551 0.154 0.645 1.137 3.85 2.95 Doc ID 8527 Rev 7 Max 0.050 16.40 28.90 3.75 2.65 Typ 0.147 0.104 0.151 0.116 STB13NK60ZT4, STx13NK60Z, STP13NK60ZFP Package mechanical data TO-220FP mechanical data mm. Dim. Min. A 4.40 inch Typ Max. Min. 4.60 0.173 Typ. 0.181 Max. B 2.5 2.7 0.098 0.106 D 2.5 2.75 0.098 0.108 E 0.45 0.70 0.017 0.027 F 0.75 1.00 0.030 0.039 F1 1.15 1.50 0.045 0.067 F2 1.15 1.50 0.045 0.067 G 4.95 5.20 0.195 0.204 G1 2.40 2.70 0.094 0.106 H 10 10.40 0.393 L2 16 0.409 0.630 28.6 30.6 1.126 L4 9.80 10.60 0.385 1.204 0.417 L5 2.9 3.6 0.114 0.141 L6 15.90 16.40 0.626 0.645 L7 9 9.30 0.354 0.366 Dia 3 3.2 0.118 0.126 B D A E L3 L3 L6 F2 H G G1 Dia F F1 L7 L2 L5 1 2 3 L4 7012510-I Doc ID 8527 Rev 7 13/18 Package mechanical data STB13NK60ZT4, STx13NK60Z, STP13NK60ZFP TO-247 Mechanical data mm. Dim. A Min. 4.85 A1 2.20 Typ 2.60 b 1.0 1.40 b1 2.0 2.40 b2 3.0 3.40 c 0.40 0.80 D 19.85 20.15 E 15.45 15.75 e 5.45 L 14.20 14.80 L1 3.70 4.30 L2 18.50 øP 3.55 3.65 øR 4.50 5.50 S 14/18 Max. 5.15 5.50 Doc ID 8527 Rev 7 STB13NK60ZT4, STx13NK60Z, STP13NK60ZFP Package mechanical data D²PAK (TO-263) mechanical data mm inch Dim Min A A1 b b2 c c2 D D1 E E1 e e1 H J1 L L1 L2 R V2 Typ 4.40 0.03 0.70 1.14 0.45 1.23 8.95 7.50 10 8.50 Max Min 4.60 0.23 0.93 1.70 0.60 1.36 9.35 0.173 0.001 0.027 0.045 0.017 0.048 0.352 0.295 0.394 0.334 10.40 2.54 4.88 15 2.49 2.29 1.27 1.30 Max 0.181 0.009 0.037 0.067 0.024 0.053 0.368 0.409 0.1 5.28 15.85 2.69 2.79 1.40 1.75 0.192 0.590 0.099 0.090 0.05 0.051 8° 0° 0.4 0° Typ 0.208 0.624 0.106 0.110 0.055 0.069 0.016 8° 0079457_M Doc ID 8527 Rev 7 15/18 Packing mechanical data 5 STB13NK60ZT4, STx13NK60Z, STP13NK60ZFP Packing mechanical data D2PAK FOOTPRINT TAPE AND REEL SHIPMENT REEL MECHANICAL DATA DIM. mm MIN. A B 1.5 C 12.8 D 20.2 G 24.4 N 100 T TAPE MECHANICAL DATA DIM. mm inch MIN. MAX. MIN. A0 10.5 10.7 0.413 0.421 MAX. B0 15.7 15.9 0.618 0.626 D 1.5 1.6 0.059 0.063 D1 1.59 1.61 0.062 0.063 E 1.65 1.85 0.065 0.073 F 11.4 11.6 0.449 0.456 K0 4.8 5.0 0.189 0.197 P0 3.9 4.1 0.153 0.161 P1 11.9 12.1 0.468 0.476 P2 1.9 2.1 0.075 0.082 R 50 1.574 T 0.25 0.35 0.0098 0.0137 W 23.7 24.3 0.933 0.956 * on sales type 16/18 Doc ID 8527 Rev 7 inch MAX. MIN. MAX. 330 12.992 13.2 0.504 0.520 26.4 0.960 1.039 0.059 0795 3.937 30.4 1.197 BASE QTY BULK QTY 1000 1000 STB13NK60ZT4, STx13NK60Z, STP13NK60ZFP 6 Revision history Revision history Table 9. Document revision history Date Revision Changes 20-Sep-2005 4 05-Oct-2005 5 Inserted ECOPACK® indication 29-Feb-2008 6 VISO parameter on Table has been updated 15-Apr-2009 7 Order codes in Table 1: Device summary has been changed Doc ID 8527 Rev 7 17/18 STB13NK60ZT4, STx13NK60Z, STP13NK60ZFP Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2009 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 18/18 Doc ID 8527 Rev 7