ROHM BU7962GUW

1/4
STRUCTURE
Silicon Monolithic Integrated Circuit
PRODUCTNAME
BU7962GUW
FUNCTION
Serial Interface for Mobile Devices Application
MSDL3(Mobile Shrink Data Link 3) Deserializer LSI
FEATURES
·Maximum transmission rate of highspeed differential interface MSDL3 is 900Mbps.
·Support LCD interface with 24bit parallel RGB video mode.
·Pixel clock frequency is 4~30MHz
1. Absolute maximum
Parameter
Power supply voltage for IOVDD
Power supply voltage for DVDD
Power supply voltage for MSVDD
Input voltage
Symbol
IOVDD
DVDD
MSVDD
VIN
Rated values
-0.3 ~ +4.5
-0.3 ~ +2.5
-0.3 ~ +2.5
-0.3 ~ IOVDD+0.3
-0.3 ~ +3.6
-0.3 ~ MSVDD+0.3
-10 ~ +10
300 *
-55 ~ +125
Unit
V
V
V
V
V
V
mA
mW
Remarks
I/O terminals of IOVDD line
XSD terminal
I/O terminals of MSVDD line
Input current
IIN
Package power dissipation
Pd
Without board mounted
Preservation temperature
Tstg
°C
*When it uses by Ta=25oC or higher, reduce by 3.0 mW/°C (for a single package).
2. Operating Condition
Parameter
Supply voltage for IOVDD
Supply voltage for DVDD
Supply voltage for MSVDD
SubLVDS data rate
Operating temperature range
Symbol
VIOVDD
VDVDD
VMSVDD
DR
Topr
Min
1.65
1.65
1.65
120
-30
Typ
1.80
1.80
1.80
25
Max
3.60
1.95
1.95
450
+85
Unit
Remarks
V
V
VDVDD=VMSVDD≤VIOVDD
V
Mbps/ch
°C
These goods are specific machines. Because the exclusive goods which are specially designed for the device are
considered. Whether that machine, device corresponds to strategic goods to decide as the foreign exchange and foreign
trade control law. You must have it judged.
As for contents of mention of these materials. A service in the foreign exchange and foreign trade control law
(Technology in the design, the manufacture and the use). Be careful of handling because it is likely to correspond.
This product is not designed against radioactive ray.
REV. A
2/4
3. ELECTRICAL CHARACTERISTICS
3.1 CMOS INOUT CHARACTERISTICS
Ta=25℃, DVDD=MSVDD=1.80V, IOVDD=1.80V,
Parameter
Symbol
Min
Typ
DGND=MSGND=0.00V, unless otherwise noted
Max
Unit
Conditions
POL_PCLK,
0.3*IOVDD
V
PLL_BW[1:0],
LS0, F_XS, TEST3
IOVDD
V
terminals
‘L’ input voltage1
VIL1
DGND
-
‘H’ input voltage1
VIH1
0.7*IOVDD
-
‘L’ input voltage2
VIL2
MSGND
-
0.3*MSVDD
V
‘H’ input voltage2
VIH2
0.7*MSVDD
-
MSVDD
V
‘H’ input voltage3
VIH3
0.7*IOVDD
-
3.6
V
XSD terminal
‘L’ output voltage1
VOL1
DGND
-
0.3*IOVDD
V
IO=1mA
‘H’ output voltage1
VOH1
0.7*IOVDD
-
IOVDD
V
IO=-1mA
‘L’ output voltage2
VOL2
DGND
-
0.3*IOVDD
V
IO=3mA
‘H’ output voltage2
VOH2
0.7*IOVDD
-
IOVDD
V
IO=-3mA
PCLK frequency1
fPCLK1
4.0
-
15.0
MHz
LS0=L
PCLK frequency2
fPCLK2
8.0
-
30.0
MHz
LS0=H
PCLK duty cycle
DPCLKO
40
50
60
%
Data setup to PCLK
TDSO
10.0
-
-
ns
Data hold to PCLK
tDHO
10.0
-
-
ns
3.2
MSDL3 RX CHARACTERISTICS
Ta=25℃, DVDD=MSVDD=1.80V, IOVDD=1.80V,
Symbol
Min
Typ
Parameter
Vdiff_rx
70
100
200
mVpp
Common mode voltage range
Vcm_rx
0.6
0.9
1.2
V
RX pull down current
Ipull_rx
12
30
90
μA
Threshold voltage of RX link
detection
Vlink_rx
0.2
0.3
0.4
V
DR_rx
120
-
450
Mbps/ch
3.3
CURRENT COMSUMPTION
Ta=25℃, DVDD=MSVDD=1.80V, IOVDD=1.80V,
Parameter
Symbol
Min
Typ
F_XS=L,
PCLK, CPO,
PD[26:0]
terminals
F_XS=H,
PCLK, CPO,
PD[26:0]
terminals
PCLK
terminal
PCLK terminal
PD[26:0] terminals
DGND=MSGND=0.00V, unless otherwise noted
Max
Unit
Conditions
Differential voltage range
SubLVDS data rate
LS1, LS_EN terminals
DGND=MSGND=0.00V, unless otherwise noted
Max
Unit
Conditions
Shutdown current
Iop_sht_rx
-
0.2
10.0
μA
XSD=L
Standby current
Iop_stb_rx
-
41.8
90.0
μA
XSD=H
Active current of
1ch27bit format
Iop_act_rx1
LS[1:0]=LL, PLL_BW[1:0]=HL,
fPCLK=15MHz, CL=10pF, *1
LS[1:0]=LH,
Active current of
Iop_act_rx2
28.0
36.8
mA PLL_BW[1:0]=HL,
2ch27bit format
fPCLK=30MHz, CL=10pF, *1
LS[1:0]=HH,
Active current of
Iop_act_rx3
17.6
23.5
mA PLL_BW[1:0]=HL,
1ch13bit format
fPCLK=30MHz, CL=10pF, *2
*1 :
Total operating current(IDVDD+IMSVDD+IIOVDD) with PD[26:0] outputs toggling 0x2AAAAAA and 0x5555555.
*2 :
Total operating current(IDVDD+IMSVDD+IIOVDD) with PD[26:15],PD[2] outputs toggling 0x0AAA and 0x1555.
-
17.6
REV. A
24.0
mA
3/4
4. PACKAGE VIEW
5. PIN LIST
1PIN
MARK
5.0±0.1
BU7962
Pin
No.
A1
A2
A3
A4
A5
A6
A7
A8
B1
B2
B3
B4
B5
B6
B7
B8
C1
C2
C3
C4
C5
C6
C7
C8
Lot No.
0.9 MAX
5.0±0.1
0.10
S
0.08
S
0.75±0.1
A
0.75±0.1
P = 0.5×7
0.5
63-φ0.295±0.05
0.05 M S AB
H
B
G
P = 0.5×7
F
E
D
C
B
A
1
2
3
4
5
6
7
8
(UNIT:mm)
VBGA063W050
6. SYSTEM BLOCK DIAGRAM
IOVDD
Pin
name
TEST0
PD18
PD16
PD15
PD13
PD12
PD9
TEST2
PCLK
PD17
PD14
PD11
PD10
PD8
PD7
PD21
PD19
DVDD
IOVDD
TEST3
DVDD
PD6
PD5
Pin
No.
D1
D2
D3
D4
D5
D6
D7
D8
E1
E2
E3
E4
E5
E6
E7
E8
F1
F2
F3
F4
F5
F6
F7
F8
DVDD
Pin
name
PD22
PD20
POL_PCLK
DGND
DGND
IOVDD
PD3
PD4
PD24
PD23
IOVDD
DGND
MSGND
PLL_BW0
PD0
PD2
PD25
PD26
MSVDD
MSGND
MSVDD
LS0
PLL_BW1
PD1
Pin
No.
G1
G2
G3
G4
G5
G6
G7
G8
H1
H2
H3
H4
H5
H6
H7
H8
MSVDD
High Speed I/F
PD
CPO
D0+
D0-
I/F
Logic
Serial
to
Parallel
Error
Detection
PCLK
D1+
D1-
PCLK
Control
Timing
Generator
Rx
CLK+
PLL
Rx
CLK-
XSD
LS
F_XS
POL_PCLK
PLL_BW
Reset
Generator
Link
Monitor
LS_EN
Control
Logic
Reference
TEST
DGND
REV. A
MSGND
DRVR
Pin
name
CPO
F_XS
DRVR
MSGND
MSVDD
LS1
LS_EN
XSD
TESTA
D1+
D1CLK+
CLKDO+
D0TEST1
4/4
7. USAGE PRECAUTIONS
(1) Absolute Maximum Ratings
An excess in the absolute maximum ratings, such as supply voltage, temperature range of operatingconditions, etc., can
break down devices, thus making impossible to identify breaking mode such as a short circuit or an open circuit. If any
special mode exceeding the absolute maximum ratings is assumed, consideration should be given to take physical safety
measures including the use of fuses, etc.
(2) Operating conditions
These conditions represent a range within which characteristics can be provided approximately as
expected. The electrical characteristics are guaranteed under the conditions of each parameter.
(3) Reverse connection of power supply connector
The reverse connection of power supply connector can break down ICs. Take protective measures against the breakdown
due to the reverse connection, such as mounting an external diode between the power supply and the IC’s power supply
terminal.
(4) Power supply line
Design PCB pattern to provide low impedance for the wiring between the power supply and the GND lines.In this regard,
for the digital block power supply and the analog block power supply, even though these power supplies has the same level
of potential, separate the power supply pattern for the digital block from that for the analog block, thus suppressing the
diffraction of digital noises to the analog block power supply resulting from impedance common to the wiring patterns. For
the GND line, give consideration to design the patterns in a similar manner.
Furthermore, for all power supply terminals to ICs, mount a capacitor between the power supply and the GND terminal. At
the same time, in order to use an electrolytic capacitor, thoroughly check to be sure the characteristics of the capacitor to be
used present no problem including the occurrence of capacity dropout at a low temperature, thus determining the constant.
(5) GND voltage
Make setting of the potential of the GND terminal so that it will be maintained at the minimum in any operating state.
Furthermore, check to be sure no terminals are at a potential lower than the GND voltage including an actual electric
transient.
(6) Short circuit between terminals and erroneous mounting
In order to mount ICs on a set PCB, pay thorough attention to the direction and offset of the ICs. Erroneous mounting can
break down the ICs. Furthermore, if a short circuit occurs due to foreign matters entering between terminals or between the
terminal and the power supply or the GND terminal, the ICs can break down.
(7) Operation in strong electromagnetic field
Be noted that using ICs in the strong electromagnetic field can malfunction them.
(8) Inspection with set PCB
On the inspection with the set PCB, if a capacitor is connected to a low-impedance IC terminal, the IC can suffer stress.
Therefore, be sure to discharge from the set PCB by each process. Furthermore, in order to mount or dismount the set
PCB to/from the jig for the inspection process, be sure to turn OFF the power supply and then mount the set PCB to the jig.
After the completion of the inspection, be sure to turn OFF the power supply and then dismount it from the jig. In addition,
for protection against static electricity, establish a ground for the assembly process and pay thorough attention to the
transportation and the storage of the set PCB.
(9) Input terminals
In terms of the construction of IC, parasitic elements are inevitably formed in relation to potential. The operation of the
parasitic element can cause interference with circuit operation, thus resulting in a malfunction and then breakdown of the
input terminal. Therefore, pay thorough attention not to handle the input terminals, such as to apply to the input terminals a
voltage lower than the GND respectively, so that any parasitic element will operate. Furthermore, do not apply a voltage to
the input terminals when no power supply voltage is applied to the IC. In addition, even if the power supply voltage is
applied, apply to the input terminals a voltage lower than the power supply voltage or within the guaranteed value of
electrical characteristics.
(10) Ground wiring pattern
If small-signal GND and large-current GND are provided, It will be recommended to separate the large-current GND pattern
from the small-signal GND pattern and establish a single ground at the reference point of the set PCB so that resistance to
the wiring pattern and voltage fluctuations due to a large current will cause no fluctuations in voltages of the small-signal
GND. Pay attention not to cause fluctuations in the GND wiring pattern of external parts as well.
(11) External capacitor
In order to use a ceramic capacitor as the external capacitor, determine the constant with consideration
given to a degradation in the nominal capacitance due to DC bias and changes in the capacitance due to
temperature, etc.
(12) No Connecting input terminals
In terms of extremely high impedance of CMOS gate, to open the input terminals causes unstable state. And unstable state
brings the inside gate voltage of p-channel or n-channel transistor into active. As a result, battery current may increase. And
unstable state can also causes unexpected operation of IC. So unless otherwise specified, input terminals not being used
should be connected to the power supply or GND line.
REV. A
Notice
Notes
No copying or reproduction of this document, in part or in whole, is permitted without the
consent of ROHM Co.,Ltd.
The content specified herein is subject to change for improvement without notice.
The content specified herein is for the purpose of introducing ROHM's products (hereinafter
"Products"). If you wish to use any such Product, please be sure to refer to the specifications,
which can be obtained from ROHM upon request.
Examples of application circuits, circuit constants and any other information contained herein
illustrate the standard usage and operations of the Products. The peripheral conditions must
be taken into account when designing circuits for mass production.
Great care was taken in ensuring the accuracy of the information specified in this document.
However, should you incur any damage arising from any inaccuracy or misprint of such
information, ROHM shall bear no responsibility for such damage.
The technical information specified herein is intended only to show the typical functions of and
examples of application circuits for the Products. ROHM does not grant you, explicitly or
implicitly, any license to use or exercise intellectual property or other rights held by ROHM and
other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the
use of such technical information.
The Products specified in this document are intended to be used with general-use electronic
equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices).
The Products specified in this document are not designed to be radiation tolerant.
While ROHM always makes efforts to enhance the quality and reliability of its Products, a
Product may fail or malfunction for a variety of reasons.
Please be sure to implement in your equipment using the Products safety measures to guard
against the possibility of physical injury, fire or any other damage caused in the event of the
failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM
shall bear no responsibility whatsoever for your use of any Product outside of the prescribed
scope or not in accordance with the instruction manual.
The Products are not designed or manufactured to be used with any equipment, device or
system which requires an extremely high level of reliability the failure or malfunction of which
may result in a direct threat to human life or create a risk of human injury (such as a medical
instrument, transportation equipment, aerospace machinery, nuclear-reactor controller,
fuel-controller or other safety device). ROHM shall bear no responsibility in any way for use of
any of the Products for the above special purposes. If a Product is intended to be used for any
such special purpose, please contact a ROHM sales representative before purchasing.
If you intend to export or ship overseas any Product or technology specified herein that may
be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to
obtain a license or permit under the Law.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact us.
ROHM Customer Support System
http://www.rohm.com/contact/
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
R0039A