1/4 ◆Structure Silicon monolithic integrated circuit ◆Product 3ch 16bit 12MSPS CIS/CCD Analog Front End ◆Type BU6577FV ◆Features ・Correlated double sampling (CDS) ・Programmable gain amplifier (8bit resolution) ・16bit 12MSPS ADC ・Serial control interface ・Offset calibration DAC (8bit resolution) ・Internally generated voltage references ・8 or 4-bit wide multiplexed data output formats ◆Absolute maximum ratings (Ta=25℃) Parameter Symbol Supply voltage 1 VAVDD Supply voltage 2 VDVDD I/O supply voltage VVDDIO Digital input voltage *1 VID Digital output voltage *2 VOD Analog input voltage *3 VIA Analog output voltage *4 VOA Storage temperature Tstg Power dissipation *5 Pd Ratings -0.2～4.0 -0.2～4.0 -0.2～4.0 -0.2～VVDDIO + 0.3 -0.2～VVDDIO + 0.3 -0.2～VAVDD + 0.3 -0.2～VAVDD + 0.3 -40～125 640 Unit V V V V V V V ℃ mW *1 : Pin No.4,5,6,7,9,11,12 *2 : Pin No.13,14,15,16,17,18,19,20 *3 : Pin No.1,27,28 *4 : Pin No.23,24,25,26 *5 : Reduced by 6.4mW for each increase in Ta of 1℃ over 25℃ ◆Operating conditions (Ta = 0℃ to 70℃) Parameter Symbol Supply voltage 1 VAVDD Supply voltage 2 VDVDD I/O supply voltage VVDDIO MIN 3.135 3.135 3.0 TYP 3.3 3.3 3.3 This product is not designed for protection against radioactive rays Status of this document The Japanese version of this document is the formal specification. A customer may use this translation version only for a reference to help reading the formal version. If there are any differences in translation version of this document, formal version takes priority. REV. A MAX 3.465 3.465 3.6 Unit V V V 2/4 ◆ Electrical characteristics (Unless otherwise noted, Ta=25℃、VAVDD=VDVDD=VVDDIO=3.3V、MCLK=24MHz) MIN SPEC TYP MAX VIN RATE 0.26 - - 2.7 12 V MSPS VIH VIL IIH IIL 0.7*VVDDIO - - 0.2*VVDDIO 1 1 V V μA μA VOH VOL VVDDIO-0.5 - - 0.5 V V Total supply current active ITOTAL - 68 130 mA Total Analog AVDD, Supply current - active IAVDD - 60 100 mA Total digital DVDD, Supply current - active IDVDD - 3 10 mA Total digital I/O, Supply current - active IVDDIO - 5 20 mA Supply current – full power down mode IPD - 30 60 μA Parameter Symbol Unit Conditions Overall System Specification Input signal limits Conversion Rate Digital Inputs High level input voltage Low level input voltage High level input current Low level input current Digital Outputs High level output voltage Low level output voltage Supply Currents REV. A IOH = 1mA IOL = 1mA MCLK=Low 3/4 ◆Package outline Part number Include. BURR BU6577FV 1PIN MARK Lot No. SSOP-B28 (Unit: mm) ◆Pin description ◆Block diagram VSMP MCLK RLC/ACYC AVDD AGND AGND TIMING CONTROL CP BANDGAP REFERENCE VIN1 CLAMP CM PGA CN OEB 8 VIN2 CLAMP PGA 8 VIN3 VBIAS GENERATOR 16-bit ADC OFFSET DAC B[0] B[1] B[2] B[3] B[4] B[5] B[6] L A T C H B[7] /SDO CLAMP PGA 8 VRLC /VBIAS OFFSET DAC OFFSET DAC 8 CONTROL REGISTER DIGITAL INTERFACE SEN SCK SDI DVDD REV. A DGND VDDIO Pin Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Pin Name VIN1 AGND DVDD OEB VSMP RLC/ACYC MCLK DGND SEN VDDIO SDI SCK B[0] B[1] B[2] B[3] B[4] B[5] B[6] B[7]/SDO AVDD AGND CN CP CM VRLC/VBIAS VIN3 VIN2 4/4 ●Cautions on use (1) Absolute Maximum Ratings An excess in the absolute maximum ratings, such as supply voltage, temperature range of operating conditions, etc., can break down devices, thus making impossible to identify breaking mode such as a short circuit or an open circuit. If any special mode exceeding the absolute maximum ratings is assumed, consideration should be given to take physical safety measures including the use of fuses, etc. (2) Power supply and GND line Design PCB pattern to provide low impedance for the wiring between the power supply and the GND lines. Pay attention to the interference by common impedance of layout pattern when there are plural power supplies and GND lines. Especially, when there are GND pattern for small signal and GND pattern for large current included the external circuits, separate each GND pattern. Furthermore, for all power supply terminals to ICs, mount a capacitor between the power supply and the GND terminal. At the same time, in order to use a capacitor, thoroughly check to be sure the characteristics of the capacitor to be used present no problem including the occurrence of capacity dropout at a low temperature, thus determining the constant. (3) GND voltage Make setting of the potential of the GND terminal so that it will be maintained at the minimum in any operating state. Furthermore, check to be sure no terminals are at a potential lower than the GND voltage including an actual electric transient. (4) Short circuit between terminals and erroneous mounting In order to mount ICs on a set PCB, pay thorough attention to the direction and offset of the ICs. Erroneous mounting can break down the ICs. Furthermore, if a short circuit occurs due to foreign matters entering between terminals or between the terminal and the power supply or the GND terminal, the ICs can break down. (5) Operation in strong electromagnetic field Be noted that using ICs in the strong electromagnetic field can malfunction them. (6) Input terminals In terms of the construction of IC, parasitic elements are inevitably formed in relation to potential. The operation of the parasitic element can cause interference with circuit operation, thus resulting in a malfunction and then breakdown of the input terminal. Therefore, pay thorough attention not to handle the input terminals; such as to apply to the input terminals a voltage lower than the GND respectively, so that any parasitic element will operate. Furthermore, do not apply a voltage to the input terminals when no power supply voltage is applied to the IC. In addition, even if the power supply voltage is applied, apply to the input terminals a voltage lower than the power supply voltage or within the guaranteed value of electrical characteristics. (7) External capacitor In order to use a ceramic capacitor as the external capacitor, determine the constant with consideration given to a degradation in the nominal capacitance due to DC bias and changes in the capacitance due to temperature, etc. (8) Rush current For ICs with more than one power supply, it is possible that rush current may flow instantaneously due to the internal powering sequence and delays. Therefore, give special consideration to power coupling capacitance, power wiring, width of GND wiring, and routing of wiring. REV. A Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuel-controller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. R0039A