XC61F Series ETR0202_001 Voltage Detectors, Delay Circuit Built-In ■GENERAL DESCRIPTION The XC61F series are highly accurate, low power consumption voltage detectors, manufactured using CMOS and laser trimming technologies. A delay circuit is built-in to each detector. Detect voltage is extremely accurate with minimal temperature drift. Both CMOS and N-channel open drain output configurations are available. Since the delay circuit is built-in, peripherals are unnecessary and high density mounting is possible. ■APPLICATIONS ■FEATURES ●Microprocessor reset circuitry Highly Accurate : ± 2% Low Power Consumption : 1.0μA(TYP.)[ VIN=2.0V ] Detect Voltage Range : 1.6V ~ 6.0V in 100mV increments Operating Voltage Range : 0.7V ~ 10.0V Detect Voltage Temperature Characteristics :±100ppm/℃(TYP.) Built-In Delay Circuit : ① 1ms ~ 50ms ② 50ms ~ 200ms ③ 80ms ~ 400ms Output Configuration : N-channel open drain or CMOS CMOS Mini Mold Package Ultra Small Packages : SOT-23 (150mW) mini-mold : SOT-89 (500mW) mini-power mold : TO-92 (300mW) * No parts are available with an accuracy of ± 1% ●Memory battery back-up circuits ●Power-on reset circuits ●Power failure detection ●System battery life and charge voltage monitors ●Delay circuitry ■TYPICAL APPLICATION CIRCUITS ■TYPICAL PERFORMANCE CHARACTERISTICS Ambient Temperature:Ta(℃) 1/12 XC61F Series ■PIN CONFIGURATION ■PIN ASSIGNMENT PIN NUMBER PIN NAME FUNCTION VIN Supply Voltage Input 2 VSS Ground 3 VOUT Output SOT-23 SOT-89 TO-92 (T) TO-92 (L) 3 2 2 1 2 3 3 1 1 1 ■PRODUCT CLASSIFICATION ●Ordering Information XC61F ①②③④⑤⑥⑦ DESIGNATOR DESCRIPTION ① Output Configuration ② ③ ④ ⑤ ⑥ ⑦ 2/12 Detect Voltage Output Delay Detect Accuracy Package Device Orientation SYMBOL DESCRIPTION C : CMOS output N : N-ch open drain output 16 ~ 60 : e.g. 2.5V → ②2 , ③5 : e.g. 3.8V → ②3, ③8 1 : 50ms ~ 200ms 4 : 80ms ~ 400ms 5 : 1ms ~ 50ms 2 : Within ± 2.0% M : SOT-23 P : SOT-89 T : TO-92 (Standard) L : TO-92 (Custom pin configuration) R : Embossed tape, standard feed L : Embossed tape, reverse feed H : Paper type (TO-92) B : Bag (TO-92) XC61F Series ■BLOCK DIAGRAMS (1) CMOS output (2) N-channel open drain output ■ABSOLUTE MAXIMUM RATINGS PARAMETER Input Voltage SYMBOL VIN Output Current IOUT CMOS N-ch open drain SOT-23 Power Dissipation SOT-89 TO-92 Operating Temperature Range Storage Temperature Range Output Voltage VOUT Pd Topr Tstg Ta = 25℃ RATINGS 12.0 UNITS V 50 VSS -0.3 ~ VIN + 0.3 VSS -0.3 ~ 9 150 500 300 -30～+85 -40～+125 mA V mW ℃ ℃ ■ELECTRICAL CHARACTERISTICS PARAMETER SYMBOL Detect Voltage VDF Hysteresis Range VHYS Supply Current ISS Operating Voltage VIN Output Current IOUT Detect Voltage Temperature Characteristics Transient Delay Time (VDR → VOUT inversion) ΔVDF ΔTopr･ VDF TDLY＊ CONDITIONS VIN = 1.5V VIN = 2.0V VIN = 3.0V VIN = 4.0V VIN = 5.0V VDF= 1.6V to 6.0V VIN = 1.0V VIN = 2.0V N-ch VDF =0.5V VIN = 3.0V VIN = 4.0V VIN = 5.0V CMOS, P-ch VDF=2.1V VIN = 8.0V VIN changes from 0.6V to 10V Ta=25℃ MIN. VDF(T) x 0.98 VDF x 0.02 0.7 - TYP. VDF(T) UNITS VDF x 0.05 0.9 1.0 1.3 1.6 2.0 2.2 7.7 10.1 11.5 13.0 -10.0 MAX. VDF(T) x 1.02 VDF x 0.08 2.6 3.0 3.4 3.8 4.2 10.0 - - ±100 - ppm/℃ 50 - 200 ms V V μA V mA VDF (T): Setting detect voltage value Release Voltage: VDR = VDF + VHYS * Transient Delay Time: 1ms to 50ms & 80ms to 400ms versions are also available. Note: The power consumption during power-start to output being stable (release operation) is 2μA greater than it is after that period (completion of release operation) because of delay circuit through current. 3/12 XC61F Series ■OPERATIONAL EXPLANATION ●CMOS output ① When a voltage higher than the release voltage (VDR) is applied to the voltage input pin (VIN), the voltage will gradually fall. When a voltage higher than the detect voltage (VDF) is applied to VIN, output (VOUT) will be equal to the input at VIN. Note that high impedance exists at VOUT with the N-channel open drain configuration. If the pin is pulled up, VOUT will be equal to the pull up voltage. ② When VIN falls below VDF, VOUT will be equal to the ground voltage (VSS) level (detect state). Note that this also applies to N-channel open drain configurations. ③ When VIN falls to a level below that of the minimum operating voltage (VMIN ) output will become unstable. Because the output pin is generally pulled up with N-channel open drain configurations, output will be equal to pull up voltage. ④ When VIN rises above the VSS level (excepting levels lower than minimum operating voltage), VOUT will be equal to VSS until VIN reaches the VDR level. ⑤ Although VIN will rise to a level higher than VDR, VOUT maintains ground voltage level via the delay circuit. ⑥ Following transient delay time, VIN will be output at VOUT. Note that high impedance exists with the N-channel open drain configuration and that voltage will be dependent on pull up. Notes: 1. The difference between VDR and VDF represents the hysteresis range. 2. Propagation delay time (tDLY) represents the time it takes for VIN to appear at VOUT once the said voltage has exceeded the VDR level. ●Timing Chart 4/12 XC61F Series ■DIRECTIONS FOR USE ●Notes on Use 1. Please use this IC within the stated maximum ratings. The IC is liable to malfunction should the ratings be exceeded. 2. When a resistor is connected between the VIN pin and the input with CMOS output configurations, oscillation may occur as a result of voltage drops at RIN if load current (IOUT) exists. It is therefore recommend that no resistor be added. (refer to Oscillation Description (1) below) 3. When a resistor is connected between the VIN pin and the input with CMOS output configurations, irrespective of N-ch output configurations, oscillation may occur as a result of through current at the time of voltage release even if load current (IOUT) does not exist. (refer to Oscillation Description (2) below) 4. With a resistor connected between the VIN pin and the input, detect and release voltage will rise as a result of the IC's supply current flowing through the VIN pin. 5. If a resistor (RIN) must be used, then please use with as small a level of input impedance as possible in order to control the occurrences of oscillation as described above. Further, please ensure that RIN is less than 10kΩ and that CIN is more than 0.1μF (Figure 1). In such cases, detect and release voltages will rise due to voltage drops at RIN brought about by the IC's supply current. ●Oscillation Description (1) Oscillation as a result of output current with the CMOS output configuration: When the voltage applied at IN rises, release operations commence and the detector's output voltage increases. Load current (IOUT) will flow through RL. Because a voltage drop (RIN x IOUT) is produced at the RIN resistor, located between the input (IN) and the VIN pin, the load current will flow via the IC's VIN pin. The voltage drop will also lead to a fall in the voltage level at the VIN pin. When the VIN pin voltage level falls below the detect voltage level, detect operations will commence. Following detect operations, load current flow will cease and since voltage drop at RIN will disappear, the voltage level at the VIN pin will rise and release operations will begin over again. Oscillation may occur with this " release - detect - release " repetition. Further, this condition will also appear via means of a similar mechanism during detect operations. (2) Oscillation as a result of through current: Since the XC61F series are CMOS ICS, through current will flow when the IC's internal circuit switching operates (during release and detect operations). Consequently, oscillation is liable to occur during release voltage operations as a result of output current which is influenced by this through current (Figure 3). Since hysteresis exists during detect operations, oscillation is unlikely to occur. Figure 1. When using an input resistor 5/12 XC61F Series ■DIRECTIONS FOR USE (Continued) ●Oscillation Description (Continued) 6/12 XC61F Series ■TYPICAL PERFORMANCE CHARACTERISTICS 7/12 XC61F Series ■TYPICAL PERFORMANCE CHARACTERISTICS (Continued) 8/12 XC61F Series ■TYPICAL PERFORMANCE CHARACTERISTICS (Continued) 9/12 XC61F Series ■PACKAGING INFORMATION ●SOT-23 ●TO-92 10/12 ●SOT-89 XC61F Series ■MARKING RULE ●SOT-23, SOT-89 3 ① ② ③ ④ 1 ③ ① ④ 2 ② 1 2 3 ①Represents integer of detect voltage and output configuration CMOS output (XC61FC series) MARK CONFIGURATION VOLTAGE (V) A CMOS 0.x B CMOS 1.x C CMOS 2.x D CMOS 3.x E CMOS 4.x F CMOS 5.x H CMOS 6.x N-channel open drain (XC61FN series) MARK CONFIGURATION VOLTAGE (V) K N-ch 0.x L N-ch 1.x M N-ch 2.x N N-ch 3.x P N-ch 4.x R N-ch 5.x S N-ch 6.x ②Represents decimal number of detect voltage MARK VOLTAGE (V) MARK 0 x.0 5 1 x.1 6 2 x.2 7 3 x.3 8 4 x.4 9 ③Represents delay time VOLTAGE (V) 5 6 7 VOLTAGE (V) x.5 x.6 x.7 x.8 x.9 DELAY TIME 50 ~ 200ms 80 ~ 400ms 1 ~ 50ms ④Represents assembly lot number (Based on internal standards) ●TO-92 ①Represents output configuration MARK C N ②, ③Represents detect voltage MARK ② 3 5 OUTPUT CONFIGURATION CMOS N-ch VOLTAGE (V) ③ 3 0 ④Represents delay time MARK 1 4 5 ⑤Represents detect voltage accuracy MARK 2 3.3 5.0 DELAY TIME 50ms ~ 200ms 80ms ~ 400ms 1ms ~ 50ms DETECT VOLTAGE ACCURACY Within +2% ⑥Represents a least significant digit of the production year (ex.) MARK PRODUCTION YEAR 3 2003 4 2004 ⑦Represents production lot number 0 to 9, A to Z repeated (G, I, J, O, Q, W expected) 11/12 XC61F Series 1. The products and product specifications contained herein are subject to change without notice to improve performance characteristics. Consult us, or our representatives before use, to confirm that the information in this catalog is up to date. 2. We assume no responsibility for any infringement of patents, patent rights, or other rights arising from the use of any information and circuitry in this catalog. 3. Please ensure suitable shipping controls (including fail-safe designs and aging protection) are in force for equipment employing products listed in this catalog. 4. The products in this catalog are not developed, designed, or approved for use with such equipment whose failure of malfunction can be reasonably expected to directly endanger the life of, or cause significant injury to, the user. (e.g. Atomic energy; aerospace; transport; combustion and associated safety equipment thereof.) 5. Please use the products listed in this catalog within the specified ranges. Should you wish to use the products under conditions exceeding the specifications, please consult us or our representatives. 6. We assume no responsibility for damage or loss due to abnormal use. 7. All rights reserved. No part of this catalog may be copied or reproduced without the prior permission of Torex Semiconductor Ltd. 12/12