TOREX XC61CC0902MR

Series
Low Voltage Detectors（VDF=0.9V∼1.5V）
◆CMOS
■Applications
◆Highly Accurate
●Microprocessor reset circuitry
: ± 2%
2
●Memory battery back-up circuits
◆Low Power Consumption : 0.7µA (VIN = 1.5V)
●Power-on reset circuits
◆Ultra small SSOT-24 (SC-82) Package
●Power failure detection
●System battery life and charge voltage monitors
■General Description
■Features
The XC61C series are highly precise, low power consumption voltage
detectors, manufactured using CMOS and laser trimming technologies.
Detect voltage is extremely accurate with minimal temperature drift.
Both CMOS and N-channel open drain output configurations are
available.
Highly accurate
: ± 2%
Low power consumption: TYP 0.7 µA [ VIN=1.5V ]
Detect voltage range
: 0.9V ~ 1.5V in 0.1V increments
Operating voltage range : 0.7V ~ 6.0V
Detect voltage temperature characteristics
: TYP± 100ppm/°C
Output configuration
: N-channel open drain or CMOS
Ultra small package
: SSOT-24 (150mW) super mini-mold
: SOT-23 (150mW) mini-mold
: SOT-89 (500mW) mini-power mold
: TO-92 ( 300mW )
Note : There are no products available with a set-up voltage
accuracy of ± 1%.
■Typical Application Circuits
VIN
VIN
R
VIN
VOUT
VIN
VSS
100kΩ
VOUT
VSS
CMOS Output
N-ch Open Drain Output
■Typical Performance Characteristic
SUPPLY CURRENT vs. INPUT VOLTAGE
Supply Current: ISS (μA)
3.5
ＸＣ６１ＣＣ０９０２ (０.９Ｖ)
3.0
2.5
2.0
1.5
Ta=85℃
25℃
1.0
0.5
-40℃
0
0
1
2
3
4
5
6
Input Voltage: VIN (V)
131
XC61C
Series
■Pin Configuration
V SS
■Pin Assignment
V IN
３
NC
４
３
1
２
V OUT
V IN
SSOT-24(SC-82)
(TOP VIEW)
PIN NUMBER
２
1
V OUT
V SS
SOT-23
(TOP VIEW)
SOT-89
PIN
TO-92 (T) TO-92 (L)
SOT-23
2
3
2
2
1
VIN
Supply Voltage Input
4
2
3
3
2
VSS
Ground
1
1
1
1
3
VOUT
Output
3
-
-
-
-
NC
No Connection
2
1
V OUT
２
V IN
３
V SS
SOT-89
(TOP VIEW)
1
2
VOUT VIN
3
1
2
3
VSS
VIN
VSS
VOUT
TO-92 (T Type)
（TOP VIEW）
TO-92 (L Type)
（TOP VIEW）
■Product Classification
●Ordering Information
XC61C x x x x x x x
a b cdef
DESIGNATOR
c
DESCRIPTION
Output Configuration :
C = CMOS
N = N-ch open drain
Detect Voltage :
09 = 0.9V
15 = 1.5V
Output Delay :
0 = No delay
d
Detect Accuracy :
2 = within ± 2.0%
a
b
132
DESIGNATOR
e
f
DESCRIPTION
Package Type:
N = SSOT-24 (SC-82)
M = SOT-23
P = SOT-89
T = TO-92 (Standard)
L = TO-92 (Custom pin Configuration)
Device Orientation :
R = Embossed Tape ( Right )
L = Embossed Tape ( Left )
H = Paper Type ( TO-92)
B = Bag ( TO-92 )
NAME
FUNCTION
SSOT-24
XC61C
Series
■Packaging Information
●SSOT-24 (SC-82)
D
e
C
2
E
He
L
b
b1
SIZE mm
A
A1
A2
MIN
y
TYP
MAX
A
0.80
1.10
A1
0.00
0.10
A2
0.80
b
0.15
1.00
0.25
0.30
b1
0.25
0.35
0.40
C
0.075
0.125
0.225
D
1.80
2.00
2.20
E
1.15
1.25
1.45
He
1.80
2.10
2.40
e
1.10
1.30
1.50
L
0.10
0.30
y
0.10
●SOT-23
0.4
+0.1
+0.1
-0.05
0.15 -0.05
0.2min
1.6
+0.2
-0.1
2.8±0.2
0∼0.1
（0.95）
1.1±0.1
1.9±0.2
2.9±0.2
133
XC61C
Series
●SOT-89
1.5±0.1
0.8
min
2
4.25max
+0.15
-0.2
2.5±0.1
1.6
（0.4）
4.5±0.1
0.42±0.06
0.42±0.06
0.4
+0.03
-0.02
0.47±0.06
1.5±0.1 1.5±0.1
●TO-92
+0.35
-0.45
1.6±0.1
3.7±0.3
10.0min
4.8 -0.5
+0.4
4.65
0.45±0.1
+0.4
2.5 -0.1
134
+0.4
2.5 -0.1
0.4±0.05
XC61C
Series
■Marking
●SSOT-24, SOT-23, SOT-89
q w r
q w e r
SSOT-24(SC-82)
(TOP VIEW)
SOT-23
(TOP VIEW)
w
r
q
e
SOT-89
(TOP VIEW)
2
q Represents the integer of the Output Voltage and Detect Voltage
CMOS Output (XC61CC series)
DESIGNATOR
A
B
N-Channel Open Drain Output (XC61CN series)
CONFIGURATION
CMOS
CMOS
VOLTAGE (V)
0.w
1.w
DESIGNATOR
K
L
w Represents the decimal number of the Detect Voltage
VOLTAGE
q.0
q.1
q.2
q.3
q.4
DESIGNATOR
0
1
2
3
4
DESIGNATOR
5
6
7
8
9
CONFIGURATION
VOLTAGE (V)
0.w
1.w
N-ch
N-ch
e Based on internal standards
( SSOT-24 excepted )
VOLTAGE
q .5
q .6
q .7
q .8
q .9
DESIGNATOR
3
r Represents the assembly lot no.
Based on internal standards
●TO-92
61C 1
61C 1
2 3 4 5 L
2 3 4 5
6 7
6 7
w Represents the Detect Voltage
q Represents the output
configuration
DESIGNATOR
OUTPUT
DESIGNATOR
CONFIGURATION
C
CMOS
N
N-ch
②
③
VOLTAGE
(V)
0
9
0.9
1
5
1.5
r Indicates Delay Time
DESIGNATOR
DELAY TIME
0
No delay
t Represents the Detect Voltage Accuracy
TO-92（T Type）
(TOP VIEW)
TO-92（L Type）
(TOP VIEW)
DESIGNATOR
DETECT VOLTAGE ACCURACY
2
within ±2％
y Represents a least significant
digit of the produced year
DESIGNATOR
Produced year
0
2000
1
2001
u Denotes the production lot number
0 to 9, A to Z repeated(G.I.J.O.Q.W excepted)
135
XC61C
Series
■Block Diagram
(2) N-ch Open Drain Output
(1) CMOS Output
V IN
V IN
＋
＋
V OUT
V OUT
−
−
Vref
Vref
2
V SS
V SS
■Absolute Maximum Ratings
Ta = 25 OC
PARAMETER
SYMBOL
RATINGS
Input Voltage
V IN
9
V
Output Current
IOUT
50
mA
Output Voltage
CMOS
N-ch open drain
VOUT
V
Pd
150
500
Operating Ambient Temperature
Topr
-40 ~ +85
O
C
Storage Temperature
Tstg
-40 ~ +125
O
C
Power Dissipation
TO-92
136
VSS -0.3 ~ 9
150
SSOT-24
SOT-23
SOT-89
VSS -0.3 ~ VIN +0.3
UNITS
mW
300
XC61C
Series
■Electrical Characteristics
V DF (T) = 0.9 to 1.5V ± 2%
Ta = 25 OC
PARAMETER
Detect Voltage
SYMBOL
V DF
Hysteresis Range
V HYS
CONDITIONS
MIN
VDF
TYP
VDF
x 0.98
Supply Current
I SS
Operating Voltage
V IN
VIN = 1.5V
=2.0V
=3.0V
=4.0V
=5.0V
VDF(T) = 0.9V to 1.5V
N-ch
Output Current
Temperature Characteristics
Delay Time
(VDR VOUT inversion)
I OUT
∆ VDF
∆ Topr • VDF
tDLY
P-ch
VDS=0.5V
VIN=0.7V
=1.0V
VDS=2.1V
VIN=6.0V
( with CMOS output )
-40 OC ≤ Topr ≤ 85OC
MAX
VDF
CIRCUIT
1
V
1
µA
2
V
1
x 1.02
VDF
VDF
VDF
x 0.02
x 0.05
x 0.08
0.7
0.8
0.9
1.0
1.1
2.3
2.7
3.0
3.2
3.6
6.0
0.7
0.1
0.85
UNITS
V
0.8
2.7
-7.5
2
3
mA
-1.5
± 100
0.2
4
ppm/°C
-
ms
5
Note :
VDF (T) : Established Detect Voltage Value
Release Voltage : VDR = VDF + VHYS
137
XC61C
Series
■Functional Description
●Functional Description ( CMOS output )
2
q When input voltage (VIN) rises above detect voltage (VDF), output voltage (VOUT) will be equal to VIN.
( A condition of high impedance exists with N-ch open drain output configurations. )
w When input voltage (VIN) falls below detect voltage (VDF), output voltage (VOUT) will be equal to the ground voltage (VSS)
level.
e When input voltage (VIN) falls to a level below that of the minimum operating voltage (VMIN), output will become unstable.
In this condition, VIN will equal the pulled-up output ( should output be pulled-up.)
r When input voltage (VIN) rises above the ground voltage (VSS) level, output will be unstable at levels below the minimum
operating voltage (VMIN). Between the VMIN and detect release voltage (VDR) levels, the ground voltage (VSS) level will be
maintained.
t When input voltage (VIN) rises above detect release voltage (VDR), output voltage (VOUT) will be equal to VIN.
( A condition of high impedance exists with N-ch open drain output configurations. )
y The difference between VDR and VDF represents the hysteresis range.
●Timing Chart
■Timing Chart
INPUT VOLTAGE (VIN)
DETECT RELEASE VOLTAGE(VDR)
y DETECT VOLTAGE(VDF)
MIN. OPERATING VOLTAGE(VMIN)
GROUND VOLTAGE (VSS)
OUTPUT VOLTAGE (VOUT)
GROUND VOLTAGE(VSS)
q w
138
e
r
t
XC61C
Series
■Directions for use
●Notes on Use
1. Please use this IC within the stated maximum ratings. Operation beyond these limits may cause degrading or
permanent damage to the device.
2. When a resistor is connected between the VIN pin and the input with CMOS output configurations, oscillation may
occur as a result of voltage drops at RIN if load current (IOUT) exists. ( refer to the Oscillation Description (1) below )
3. When a resistor is connected between the VIN pin and the input with CMOS output configurations, irrespective of
N-ch output configurations, oscillation may occur as a result of through current at the time of voltage release even
if load current (IOUT) does not exist. ( refer to the Oscillation Description (2) below )
2
4. With a resistor connected between the VIN pin and the input, detect and release voltage will rise as a result of the
IC's supply current flowing through the VIN pin.
5. In order to stabilise the IC's operations, please ensure that VIN pin's input frequency's rise and fall times are more
than several μ sec / V.
6. Please use N-ch open drains configuration, when a resistor R IN is connected between the V IN pin and power
source.
In such cases, please ensure that RIN is less than 10kΩ and that C is more than 0.1μF.
XC61CN Series
RIN
VOUT
VIN
VSS
C
Diagram: Circuit using an input resistor
●Oscillation Description
(1) Output current oscillation with the CMOS output configuration
When the voltage applied at IN rises, release operations commence and the detector's output voltage increases.
Load current (IOUT) will flow at RL. Because a voltage drop ( RIN x I OUT) is produced at the RIN resistor, located
between the input (IN) and the VIN pin, the load current will flow via the IC's VIN pin. The voltage drop will also lead
to a fall in the voltage level at the VIN pin. When the VIN pin voltage level falls below the detect voltage level, detect
operations will commence. Following detect operations, load current flow will cease and since voltage drop at RIN
will disappear, the voltage level at the VIN pin will rise and release operations will begin over again.
Oscillation may occur with this " release - detect - release " repetition.
Further, this condition will also appear via means of a similar mechanism during detect operations.
(2) Oscillation as a result of through current
Since the XC61C series are CMOS IC S, through current will flow when the IC's internal circuit switching operates
( during release and detect operations ). Consequently, oscillation is liable to occur as a result of drops in voltage
at the through current's resistor (RIN) during release voltage operations. ( refer to diagram 2 )
Since hysteresis exists during detect operations, oscillation is unlikely to occur.
IN
IN
RIN
XC61CC Series
RIN
RIN x IOUT
Voltage Drop
VIN
IOUT
VOUT
VSS
XC61CC Series
XC61CN Series
RIN x ISS
Voltage Drop
VIN
VOUT
VSS
RL
ISS*
（Includes Current）
Diagram 1: Oscillation in relation to output current
Diagram 2: Oscillation in relation to through current
139
XC61C
Series
■Measuring Circuits
Circuit 2
Circuit 1
A
R
VIN
100kΩ
(Note 1)
VIN
VOUT
VOUT
V
2
VSS
VSS
V
Circuit 3
VIN
Circuit 4
VDS
VIN
VIN
VIN
VOUT
VOUT
A
VSS
VDS
Circuit 5
R
VIN
VOUT
100kΩ
(Note 1)
measurement of
waveform
VSS
Note 1 : Not necessary with CMOS output products.
140
VIN
VIN
VSS
A
XC61C
Series
■Typical Performance Characteristics
(1) SUPPLY CURRENT vs. INPUT VOLTAGE
3.5
3.0
2.5
2.0
1.5
Ta=85℃
25℃
1.0
0.5
-40℃
0
ＸＣ６１ＣＣ１１０２ (１.１Ｖ)
3.5
3.0
Supply Current: ISS (μA)
ＸＣ６１ＣＣ０９０２ (０.９Ｖ)
Supply Current: ISS (μA)
Supply Current: ISS (μA)
3.5
2.5
2.0
1.5
25℃
Ta=85℃
1.0
0.5
-40℃
1
2
3
4
5
6
3.0
2.5
2.0
1.5
Ta=85℃
25℃
2
1.0
0.5
-40℃
0
0
0
ＸＣ６１ＣＣ１５０２ (１.５Ｖ)
0
Input Voltage: VIN (V)
1
2
3
4
5
0
6
1
2
3
4
5
6
Input Voltage: VIN (V)
Input Voltage: VIN (V)
(2) DETECT, RELEASE VOLTAGE vs. AMBIENT TEMPERATURE
0.95
1.20
VDR
0.90
VDF
0.85
0.80
-50
-25
0
25
50
75
100
ＸＣ６１ＣＣ１１０２ (１.１Ｖ)
1.60
Detect, Release Voltage: VDF,VDR (V)
ＸＣ６１ＣＣ０９０２ (０.９Ｖ)
Detect, Release Voltage: VDF,VDR (V)
Detect, Release Voltage: VDF,VDR (V)
1.00
VDR
1.15
1.10
VDF
1.05
1.00
-50
Ambient Temp.: Ta (℃)
-25
0
25
50
75
100
ＸＣ６１ＣＣ１５０２ (１.５Ｖ)
VDR
1.55
1.50
VDF 1.45
1.40
-50
-25
0
25
50
75
100
Ambient Temp.: Ta (℃)
Ambient Temp.: Ta (℃)
(3) OUTPUT VOLTAGE vs. INPUT VOLTAGE
ＸＣ６１ＣＮ０９０２ (０.９Ｖ)
1.4
Output Voltage: VOUT (V)
Output Voltage: VOUT (V)
Ta=25℃
1.0
0.8
0.6
0.4
0.2
0
ＸＣ６１ＣＮ１１０２ (１.１Ｖ)
2.0
1.2
1.0
0.8
0.6
0.4
0.2
0.2
0.4
0.6
0.8
Input Voltage: VIN (V)
1.0
1.2
Ta=25℃
1.5
1.0
0.5
0
0
0
ＸＣ６１ＣＮ１５０２ (１.５Ｖ)
Ta=25℃
Output Voltage: VOUT (V)
1.2
0
0.2
0.4
0.6
0.8
1.0
Input Voltage: VIN (V)
1.2
1.4
0
0.5
1.0
1.5
2.0
Input Voltage: VIN (V)
Note : The N-channel open drain pull up resistance value is 100kΩ
141
XC61C
Series
(4) N-ch DRIVER OUTPUT CURRENT vs. VDS
ＸＣ６１ＣＣ０９０２ (０.９Ｖ)
ＸＣ６１ＣＣ１１０２ (１.１Ｖ)
VIN =0.8V
1.0
0.8
0.6
0.7V
0.4
0.2
0
0
0.2
0.4
0.6
0.8
VIN =0.8V
1.0
0.8
0.6
0.7V
0.4
0.2
0
1.0
Ta=25℃
1.2
0
0.2
0.4
VDS (V)
ＸＣ６１ＣＣ１５０２ (１.５Ｖ)
0.8
1.5
1.0
0.5
0
1.0
0
0.2
0.4
0.6
0.8
1.0
VDS (V)
ＸＣ６１ＣＣ１５０２ (１.５Ｖ)
Ta=25℃
Ta=25℃
1.2
VIN =0.8V
1.0
0.8
0.6
0.7V
0.4
0.2
0
0.2
0.4
0.6
0.8
VIN =1.4V
6.0
1.2V
4.0
1.0V
2.0
0
1.0
0
0.2
0.4
VDS (V)
0.6
0.8
1.0
1.2
1.4
VDS (V)
(5) N-ch DRIVER OUTPUT CURRENT vs. INPUT VOLTAGE
ＸＣ６１ＣＣ１１０２ (１.１Ｖ)
ＸＣ６１ＣＣ０９０２ (０.９Ｖ)
ＸＣ６１ＣＣ１５０２ (１.５Ｖ)
10
5.0
Output Current: IOUT (mA)
VDS=0.5V
2.0
1.5
1.0
Ta=85℃
25℃
0.5
-40℃
0
Ta=-40℃
VDS=0.5V
Output Current: IOUT (mA)
2.5
Output Current: IOUT (mA)
VIN =1.0V
2.0
8.0
Output Current: IOUT (mA)
Output Current: IOUT (mA)
0.6
2.5
VDS (V)
1.4
0
Output Current: IOUT (mA)
Ta=25℃
1.2
3.0
Ta=25℃
Output Current: IOUT (mA)
Output Current: IOUT (mA)
2
ＸＣ６１ＣＣ１１０２ (１.１Ｖ)
1.4
1.4
4.0
25℃
3.0
2.0
80℃
1.0
0.2
0.4
0.6
0.8
1.0
Ta=-40℃
25℃
6
4
85℃
2
0
0
0
VDS=0.5V
8
0
Input Voltage: VIN (V)
0.2
0.4
0.6
0.8
1.0
1.2
0
Input Voltage: VIN (V)
0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6
Input Voltage: VIN (V)
(6) P-ch DRIVER OUTPUT CURRENT vs. INPUT VOLTAGE
ＸＣ６１ＣＣ０９０２ (０.９Ｖ)
ＸＣ６１ＣＣ１１０２ (１.１Ｖ)
12
Ta= 25℃
VDS=2.1V
8
1.5V
6
1.0V
4
0.5V
2
VDS=2.1V
10
8
1.5V
6
1.0V
4
0.5V
2
1
2
3
4
Input Voltage: VIN (V)
5
6
Ta= 25℃
10
VDS=2.1V
8
1.5V
6
1.0V
4
0.5V
2
0
0
0
Output Current: IOUT (mA)
Ta= 25℃
10
0
142
ＸＣ６１ＣＣ１５０２ (１.５Ｖ)
12
Output Current: IOUT (mA)
Output Current: IOUT (mA)
12
0
1
2
3
4
Input Voltage: VIN (V)
5
6
0
1
2
3
4
Input Voltage: VIN (V)
5
6