GI750 THRU GI758 HIGH CURRENT PLASTIC RECTIFIER Reverse Voltage - 50 to 800 Volts Forward Current - 6.0 Amperes FEATURES Case style P600 ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ High forward current capability ♦ Diffused junction ♦ Construction utilizes void-free molded plastic technique ♦ High surge current capability ♦ High temperature soldering guaranteed: 250°C/10 seconds, 0.375" (9.5mm) lead length, 5 lbs. (2.3kg) tension 1.0 (25.4) MIN. 0.360 (9.1) 0.340 (8.6) 0.360 (9.1) 0.340 (8.6) MECHANICAL DATA 0.052 (1.32) 0.048 (1.22) DIA. Case: Void-free molded plastic body Terminals: Plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight: 0.07 ounce, 2.1 grams 1.0 (25.4) MIN. Dimensions are in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS GI750 GI751 GI752 GI754 GI756 GI758 UNITS Maximum repetitive peak reverse voltage VRRM 50 100 200 400 600 800 Volts Maximum RMS voltage VRMS 35 70 140 280 420 560 Volts VDC 50 100 200 400 600 800 Volts Maximum non-repetitive peak reverse voltage VRSM 60 120 240 480 720 1200 Volts Maximum average forward rectified current at TA=60°C, P.C.B. mounting (FIG. 1) TL=60°C, 0.125" (3.18mm) lead length (FIG. 2) I(AV) 6.0 22.0 Amps Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) IFSM 400.0 Amps Maximum instantaneous forward voltage at 6.0A 100A VF 0.90 1.25 Maximum DC reverse current at rated DC blocking voltage IR 5.0 1.0 µA mA CJ 150.0 pF Maximum DC blocking voltage TA=25°C TA=100°C Typical junction capacitance (NOTE 1) Typical reverse recovery time (NOTE 2) Typical thermal resistance (NOTE 3) Operating junction and storage temperature range Volts trr 2.5 µs RΘJA RΘJL 20.0 4.0 °C/W TJ, TSTG -50 to +150 °C NOTES: (1) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts (2) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25A (3) Thermal resistance from junction to ambient and from junction to lead at 0.375” (9.5mm) lead length, P.C.B. mounted with 1.1 x 1.1” (30 x 30mm) copper pads 10/12/98 0.95 1.30 AVERAGE FORWARD RECTIFIED CURRENT, AMPERES RATINGS AND CHARACTERISTIC CURVES GI750 THRU GI758 FIG.1 - MAXIMUM FORWARD CURRENT DERATING CURRENT FIG. 2 - MAXIMUM FORWARD CURRENT DERATING CURVE 60 HZ RESISTIVE or INDUCTIVE LOAD AVERAGE FORWARD CURRENT, AMPERES 28 1.1 x 1.1” (30 x 30mm) COPPER PADS 0 20 40 60 80 100 120 140 160 180 200 AMBIENT TEMPERATURE, °C L=0.125” (3.18mm) L=0.25” (6.35mm) 24 60 HZ RESISTIVE or INDUCTIVE LOAD 20 16 L=0.375” (9.5mm) 12 BOTH LEADS ATTACHED to HEAT SINKS with LENGTH as SHOWN “L” 8.0 4.0 0 0 L=0.625”(15.8mm) 20 40 60 80 100 120 140 160 180 200 LEAD TEMPERATURE, °C FIG. 3 - MAXIMUM PEAK FORWARD SURGE CURRENT FIG. 4 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS VRRM may be APPLIED BETWEEN EACH CYCLE of SURGE, the TJ NOTED is TJ PRIOR to SURGE NO EP ITIV TJ=25°C TJ= 150 25° C RE PE 100 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE ET E TJ= 100 INSTANTANEOUS FORWARD CURRENT, AMPERES N-R °C TIT IVE TJ=150°C 50 1 10 100 NUMBER OF CYCLES AT 60 HZ 10 1 0.1 FIG. 5 - TYPICAL REVERSE CHARACTERISTICS 100 0.01 0.6 0.8 1.0 1.2 1.4 1.6 1.8 INSTANTANEOUS FORWARD VOLTAGE, VOLTS 10 FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE TJ=125°C TRANSIENT THERMAL IMPEDANCE, °C/W INSTANTANEOUS REVERSE CURRENT, MICROAMPERES PEAK FORWARD SURGE CURRENT AMPERES 600 TJ=100°C 1 TJ=25°C 0.1 0.01 0 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE, % 100 10 1 0.1 0.01 0.1 1 t, PULSE DURATION, sec. 10 100