1N4001 THRU 1N4007 GENERAL PURPOSE PLASTIC RECTIFIER Reverse Voltage - 50 to 1000 Volts Forward Current - 1.0 Ampere DO-204AL FEATURES ♦ The plastic package carries Underwriters Laboratory Flammability Classification 94V-0 ♦ Construction utilizes void-free molded plastic technique ♦ Low reverse leakage ♦ High forward surge current capability ♦ High temperature soldering guaranteed: 250°C/10 seconds, 0.375" (9.5mm) lead length, 5 lbs. (2.3kg) tension 1.0 (25.4) MIN. 0.107 (2.7) 0.080 (2.0) DIA. 0.205 (5.2) 0.160 (4.1) MECHANICAL DATA Case: JEDEC DO-204AL molded plastic body Terminals: Plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight: 0.012 ounce, 0.3 gram 1.0 (25.4) MIN. 0.034 (0.86) 0.028 (0.71) DIA. NOTE: Lead diameter is 0.026 (0.66) 0.023 (0.58) for suffix "E" part numbers Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS 1N 4001 1N 4002 1N 4003 1N 4004 1N 4005 1N 4006 1N 4007 UNITS *Maximum repetitive peak reverse voltage VRRM 50 100 200 400 600 800 1000 Volts *Maximum RMS voltage VRMS 35 70 140 280 420 560 700 Volts *Maximum DC blocking voltage VDC 50 100 200 400 600 800 1000 Volts *Maximum average forward rectified current 0.375" (9.5mm) lead length at T A=75°C I(AV) 1.0 Amp *Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) TA=75°C IFSM 30.0 Amps *Maximum instantaneous forward voltage at 1.0A VF 1.1 Volts *Maximum full load reverse current full cycle average 0.375" (9.5mm) lead length at TL=75°C IR(AV) 30.0 µA IR 5.0 50.0 µA trr 30.0 µs *Maximum DC reverse current at rated DC blocking voltage TA= 25°C TA=100°C Typical reverse recovery time (NOTE 1) Typical junction capacitance (NOTE 2) Typical thermal resistance (NOTE 3) Maximum DC blocking voltage temperature *Operating junction and storage temperature range CJ 15.0 pF RΘJA RΘJL 50.0 25.0 °C/W TA +150 °C TJ, TSTG -50 to +175 °C NOTES: (1) Measured on Tektronix Type "S" recovery plug-in. Tektronix 545 Scope or equivalent, IFM=20mA, IRM=1mA (2) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts (3) Thermal resistance from junction to ambient and from junction to lead at 0.375" (9.5mm) lead length, P.C.B. mounted *JEDEC registered value 4/98 RATINGS AND CHARACTERISTIC CURVES 1N4001 THRU 1N4007 FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 1.0 30 60 HZ RESISTIVE OR INDUCTIVE LOAD PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD RECTIFIED CURRENT, AMPERES FIG.1 - FORWARD CURRENT DERATING CURVE 0.8 0.2 x 0.2” (5.0 x 5.0mm) COPPER PADS 0.6 0.4 0.2 8.3ms SINGLE HALF SINE WAVE (JEDEC Method) TA=75°C 25 20 15 10 0.375” (9.5mm) LEAD LENGTH 0 5.0 0 25 50 75 100 125 150 175 1 AMBIENT TEMPERATURE, °C 10 100 NUMBER OF CYCLES AT 60 HZ INSTANTANEOUS REVERSE CURRENT, MICROAMPERES FIG. 4 - TYPICAL REVERSE CHARACTERISTICS FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS INSTANTANEOUS FORWARD CURRENT, AMPERES 20 10 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 1 0.1 0.01 0.6 0.8 1.0 1.2 1.4 1.6 1.8 INSTANTANEOUS FORWARD VOLTAGE, VOLTS 1,000 100 TJ=150°C 10 TJ=100°C 1 0.1 TJ=25°C 0.01 0 20 40 60 80 100 PERCENTAGE OF PEAK REVERSE VOLTAGE, % FIG. 5 - TYPICAL JUNCTION CAPACITANCE TJ=25°C f=1.0 MHz Vsig=50mVp-p 10 1 0.1 1 10 REVERSE VOLTAGE, VOLTS 100 FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE TRANSIENT THERMAL IMPEDANCE, °C/W JUNCTION CAPACITANCE, pF 100 100 10 1 0.1 0.01 0.1 1 t, PULSE DURATION, sec. 10 100