ONSEMI MC74HC4052

MC74HC4051A,
MC74HC4052A,
MC74HC4053A
Analog Multiplexers /
Demultiplexers
High–Performance Silicon–Gate CMOS
The MC74HC4051A, MC74HC4052A and MC74HC4053A utilize
silicon–gate CMOS technology to achieve fast propagation delays,
low ON resistances, and low OFF leakage currents. These analog
multiplexers/demultiplexers control analog voltages that may vary
across the complete power supply range (from VCC to VEE).
The HC4051A, HC4052A and HC4053A are identical in pinout to
the metal–gate MC14051AB, MC14052AB and MC14053AB. The
Channel–Select inputs determine which one of the Analog
Inputs/Outputs is to be connected, by means of an analog switch, to the
Common Output/Input. When the Enable pin is HIGH, all analog
switches are turned off.
The Channel–Select and Enable inputs are compatible with standard
CMOS outputs; with pullup resistors they are compatible with LSTTL
outputs.
These devices have been designed so that the ON resistance (Ron) is
more linear over input voltage than Ron of metal–gate CMOS analog
switches.
For a multiplexer/demultiplexer with injection current protection,
see HC4851A and HC4852A.
• Fast Switching and Propagation Speeds
• Low Crosstalk Between Switches
• Diode Protection on All Inputs/Outputs
• Analog Power Supply Range (VCC – VEE) = 2.0 to 12.0 V
• Digital (Control) Power Supply Range (VCC – GND) = 2.0 to 6.0 V
• Improved Linearity and Lower ON Resistance Than Metal–Gate
Counterparts
• Low Noise
• In Compliance With the Requirements of JEDEC Standard No. 7A
• Chip Complexity: HC4051A — 184 FETs or 46 Equivalent Gates
HC4052A — 168 FETs or 42 Equivalent Gates
HC4053A — 156 FETs or 39 Equivalent Gates
http://onsemi.com
MARKING
DIAGRAMS
16
PDIP–16
N SUFFIX
CASE 648
16
1
HC405xAN
AWLYYWW
1
16
SO–16
D SUFFIX
CASE 751B
16
1
HC405xAD
AWLYYWW
1
16
SO–16 WIDE
DW SUFFIX
CASE 751G
16
HC405xA
AWLYWW
1
1
16
HC40
5xA
ALYW
TSSOP–16
DT SUFFIX
CASE 948F
16
1
1
16
SOEIAJ–16
F SUFFIX
CASE 966
16
1
74HC405xA
ALYW
1
A
WL
YY
WW
= Assembly Location
= Wafer Lot
= Year
= Work Week
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 13 of this data sheet.
 Semiconductor Components Industries, LLC, 2000
March, 2000 – Rev. 1
1
Publication Order Number:
MC74HC4051A/D
MC74HC4051A, MC74HC4052A, MC74HC4053A
FUNCTION TABLE – MC74HC4051A
LOGIC DIAGRAM
MC74HC4051A
Single–Pole, 8–Position Plus Common Off
Control Inputs
Enable
C
L
L
L
L
L
L
L
L
H
L
L
L
L
H
H
H
H
X
13
X0
14
X1
15
X2
ANALOG
12
MULTIPLEXER/
INPUTS/ X3
DEMULTIPLEXER
OUTPUTS X4 1
5
X5
2
X6
4
X7
11
A
CHANNEL
10
B
SELECT
9
INPUTS
C
6
ENABLE
PIN 16 = VCC
PIN 7 = VEE
PIN 8 = GND
3
X
COMMON
OUTPUT/
INPUT
Select
B
A
ON Channels
X0
X1
X2
X3
X4
X5
X6
X7
NONE
L
H
L
H
L
H
L
H
X
L
L
H
H
L
L
H
H
X
X = Don’t Care
Pinout: MC74HC4051A (Top View)
VCC
16
X2
X1
X0
X3
A
B
C
15
14
13
12
11
10
9
6
7
8
GND
1
2
3
4
5
X4
X6
X
X7
X5
Enable VEE
FUNCTION TABLE – MC74HC4052A
LOGIC DIAGRAM
MC74HC4052A
Double–Pole, 4–Position Plus Common Off
Control Inputs
Select
Enable
B
A
ON Channels
L
L
L
L
H
L
L
H
H
X
L
H
L
H
X
Y0
Y1
Y2
Y3
12
ANALOG
INPUTS/OUTPUTS
CHANNEL-SELECT
INPUTS
X0
14
X1
15
X2
11
X3
Y0
Y1
Y2
Y3
A
B
ENABLE
X SWITCH
13
X
COMMON
OUTPUTS/INPUTS
1
5
2
Y SWITCH
3
Y
4
6
NONE
X = Don’t Care
Pinout: MC74HC4052A (Top View)
10
9
X0
X1
X2
X3
VCC
16
PIN 16 = VCC
PIN 7 = VEE
PIN 8 = GND
http://onsemi.com
2
X2
X1
X
X0
X3
A
B
15
14
13
12
11
10
9
6
7
8
GND
1
2
3
4
5
Y0
Y2
Y
Y3
Y1
Enable VEE
MC74HC4051A, MC74HC4052A, MC74HC4053A
FUNCTION TABLE – MC74HC4053A
Control Inputs
LOGIC DIAGRAM
MC74HC4053A
Triple Single–Pole, Double–Position Plus Common Off
12
X0
13
X1
14
X SWITCH
2
ANALOG
INPUTS/OUTPUTS
Y0
1
Y1
15
Y SWITCH
5
Z0
3
Z1
4
Z SWITCH
Enable
C
L
L
L
L
L
L
L
L
H
L
L
L
L
H
H
H
H
X
X
Y
COMMON
OUTPUTS/INPUTS
Select
B
A
L
L
H
H
L
L
H
H
X
ON Channels
Z0
Z0
Z0
Z0
Z1
Z1
Z1
Z1
L
H
L
H
L
H
L
H
X
Y0
Y0
Y1
Y1
Y0
Y0
Y1
Y1
NONE
X0
X1
X0
X1
X0
X1
X0
X1
X = Don’t Care
Z
11
A
10
B
9
C
6
ENABLE
PIN 16 = VCC
PIN 7 = VEE
PIN 8 = GND
CHANNEL-SELECT
INPUTS
Pinout: MC74HC4053A (Top View)
VCC
16
Y
X
X1
X0
A
B
C
15
14
13
12
11
10
9
6
7
8
GND
NOTE: This device allows independent control of each switch.
Channel–Select Input A controls the X–Switch, Input B controls
the Y–Switch and Input C controls the Z–Switch
1
2
3
4
5
Y1
Y0
Z1
Z
Z0
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎ
Enable VEE
MAXIMUM RATINGS*
Symbol
Parameter
Value
Unit
– 0.5 to + 7.0
– 0.5 to + 14.0
V
Negative DC Supply Voltage (Referenced to GND)
– 7.0 to + 5.0
V
VIS
Analog Input Voltage
VEE – 0.5 to
VCC + 0.5
V
Vin
Digital Input Voltage (Referenced to GND)
– 0.5 to VCC + 0.5
V
DC Current, Into or Out of Any Pin
± 25
mA
PD
Power Dissipation in Still Air,
750
500
450
mW
Tstg
Storage Temperature Range
– 65 to + 150
_C
VCC
Positive DC Supply Voltage
VEE
I
TL
(Referenced to GND)
(Referenced to VEE)
Plastic DIP†
EIAJ/SOIC Package†
TSSOP Package†
This device contains protection
circuitry to guard against damage
due to high static voltages or electric
fields. However, precautions must
be taken to avoid applications of any
voltage higher than maximum rated
voltages to this high–impedance circuit. For proper operation, Vin and
Vout should be constrained to the
range GND (Vin or Vout) VCC.
Unused inputs must always be
tied to an appropriate logic voltage
level (e.g., either GND or VCC).
Unused outputs must be left open.
v
v
_C
Lead Temperature, 1 mm from Case for 10 Seconds
Plastic DIP, SOIC or TSSOP Package
260
*Maximum Ratings are those values beyond which damage to the device may occur.
Functional operation should be restricted to the Recommended Operating Conditions.
†Derating — Plastic DIP: – 10 mW/_C from 65_ to 125_C
EIAJ/SOIC Package: – 7 mW/_C from 65_ to 125_C
TSSOP Package: – 6.1 mW/_C from 65_ to 125_C
For high frequency or heavy load considerations, see Chapter 2 of the ON Semiconductor High–Speed CMOS Data Book (DL129/D).
http://onsemi.com
3
MC74HC4051A, MC74HC4052A, MC74HC4053A
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎ
ÎÎÎ
ÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎ
RECOMMENDED OPERATING CONDITIONS
Symbol
Parameter
Min
Max
Unit
2.0
2.0
6.0
12.0
V
Negative DC Supply Voltage, Output (Referenced to
GND)
– 6.0
GND
V
VIS
Analog Input Voltage
VEE
VCC
V
Vin
Digital Input Voltage (Referenced to GND)
GND
VCC
V
VIO*
Static or Dynamic Voltage Across Switch
1.2
V
– 55
+ 125
_C
0
0
0
0
1000
600
500
400
ns
VCC
Positive DC Supply Voltage
VEE
(Referenced to GND)
(Referenced to VEE)
TA
Operating Temperature Range, All Package Types
tr, tf
Input Rise/Fall Time
(Channel Select or Enable Inputs)
VCC = 2.0 V
VCC = 3.0 V
VCC = 4.5 V
VCC = 6.0 V
*For voltage drops across switch greater than 1.2V (switch on), excessive VCC current may be
drawn; i.e., the current out of the switch may contain both VCC and switch input components.
The reliability of the device will be unaffected unless the Maximum Ratings are exceeded.
DC CHARACTERISTICS — Digital Section (Voltages Referenced to GND) VEE = GND, Except Where Noted
Symbol
Parameter
Condition
Guaranteed Limit
VCC
V
–55 to 25°C
≤85°C
≤125°C
Unit
VIH
Minimum High–Level Input
Voltage, Channel–Select or
Enable Inputs
Ron = Per Spec
2.0
3.0
4.5
6.0
1.50
2.10
3.15
4.20
1.50
2.10
3.15
4.20
1.50
2.10
3.15
4.20
V
VIL
Maximum Low–Level Input
Voltage, Channel–Select or
Enable Inputs
Ron = Per Spec
2.0
3.0
4.5
6.0
0.5
0.9
1.35
1.8
0.5
0.9
1.35
1.8
0.5
0.9
1.35
1.8
V
Iin
Maximum Input Leakage Current,
Channel–Select or Enable Inputs
Vin = VCC or GND,
VEE = – 6.0 V
6.0
± 0.1
± 1.0
± 1.0
µA
Maximum Quiescent Supply
Current (per Package)
Channel Select, Enable and
VIS = VCC or GND; VEE = GND
VIO = 0 V
VEE = – 6.0
6.0
6.0
1
4
10
40
20
80
ICC
µA
NOTE: Information on typical parametric values can be found in Chapter 2 of the ON Semiconductor High–Speed CMOS Data Book (DL129/D).
http://onsemi.com
4
MC74HC4051A, MC74HC4052A, MC74HC4053A
DC CHARACTERISTICS — Analog Section
Guaranteed Limit
Symbol
Ron
Condition
VCC
VEE
–55 to 25°C
≤85°C
≤125°C
Unit
Vin = VIL or VIH; VIS = VCC to
VEE; IS ≤ 2.0 mA
(Figures 1, 2)
4.5
4.5
6.0
0.0
– 4.5
– 6.0
190
120
100
240
150
125
280
170
140
Ω
Vin = VIL or VIH; VIS = VCC or
VEE (Endpoints); IS ≤ 2.0 mA
(Figures 1, 2)
4.5
4.5
6.0
0.0
– 4.5
– 6.0
150
100
80
190
125
100
230
140
115
Parameter
Maximum “ON” Resistance
∆Ron
Maximum Difference in “ON”
Resistance Between Any Two
Channels in the Same Package
Vin = VIL or VIH;
VIS = 1/2 (VCC – VEE);
IS ≤ 2.0 mA
4.5
4.5
6.0
0.0
– 4.5
– 6.0
30
12
10
35
15
12
40
18
14
Ioff
Maximum Off–Channel Leakage
Current, Any One Channel
Vin = VIL or VIH;
VIO = VCC – VEE;
Switch Off (Figure 3)
6.0
– 6.0
0.1
0.5
1.0
Maximum Off–Channel HC4051A Vin = VIL or VIH;
Leakage Current,
HC4052A VIO = VCC – VEE;
Common Channel
HC4053A Switch Off (Figure 4)
6.0
6.0
6.0
– 6.0
– 6.0
– 6.0
0.2
0.1
0.1
2.0
1.0
1.0
4.0
2.0
2.0
Maximum On–Channel HC4051A Vin = VIL or VIH;
Leakage Current,
HC4052A Switch–to–Switch =
Channel–to–Channel HC4053A VCC – VEE; (Figure 5)
6.0
6.0
6.0
– 6.0
– 6.0
– 6.0
0.2
0.1
0.1
2.0
1.0
1.0
4.0
2.0
2.0
Ion
Ω
µA
µA
AC CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6 ns)
Guaranteed Limit
VCC
V
–55 to 25°C
≤85°C
≤125°C
Unit
Symbol
Parameter
tPLH,
tPHL
Maximum Propagation Delay, Channel–Select to Analog Output
(Figure 9)
2.0
3.0
4.5
6.0
270
90
59
45
320
110
79
65
350
125
85
75
ns
tPLH,
tPHL
Maximum Propagation Delay, Analog Input to Analog Output
(Figure 10)
2.0
3.0
4.5
6.0
40
25
12
10
60
30
15
13
70
32
18
15
ns
tPLZ,
tPHZ
Maximum Propagation Delay, Enable to Analog Output
(Figure 11)
2.0
3.0
4.5
6.0
160
70
48
39
200
95
63
55
220
110
76
63
ns
tPZL,
tPZH
Maximum Propagation Delay, Enable to Analog Output
(Figure 11)
2.0
3.0
4.5
6.0
245
115
49
39
315
145
69
58
345
155
83
67
ns
Cin
Maximum Input Capacitance, Channel–Select or Enable Inputs
10
10
10
pF
CI/O
Maximum Capacitance
Analog I/O
35
35
35
pF
Common O/I: HC4051A
HC4052A
HC4053A
130
80
50
130
80
50
130
80
50
Feedthrough
1.0
1.0
1.0
(All Switches Off)
NOTE: For propagation delays with loads other than 50 pF, and information on typical parametric values, see Chapter 2 of the ON
Semiconductor High–Speed CMOS Data Book (DL129/D)
Typical @ 25°C, VCC = 5.0 V, VEE = 0 V
CPD
Power Dissipation Capacitance (Figure 13)*
HC4051A
HC4052A
HC4053A
45
80
45
pF
* Used to determine the no–load dynamic power consumption: P D = C PD V CC 2 f + I CC V CC . For load considerations, see Chapter 2 of the
ON Semiconductor High–Speed CMOS Data Book (DL129/D).
http://onsemi.com
5
MC74HC4051A, MC74HC4052A, MC74HC4053A
ADDITIONAL APPLICATION CHARACTERISTICS (GND = 0 V)
Symbol
BW
—
—
Parameter
2.25
4.50
6.00
–2.25
–4.50
–6.00
Off–Channel Feedthrough Isolation
(Figure 7)
fin = Sine Wave; Adjust fin Voltage to
Obtain 0dBm at VIS
fin = 10kHz, RL = 600Ω, CL = 50pF
2.25
4.50
6.00
–2.25
–4.50
–6.00
–50
–50
–50
fin = 1.0MHz, RL = 50Ω, CL = 10pF
2.25
4.50
6.00
–2.25
–4.50
–6.00
–40
–40
–40
Vin ≤ 1MHz Square Wave (tr = tf = 6ns);
Adjust RL at Setup so that IS = 0A;
Enable = GND
RL = 600Ω, CL = 50pF
2.25
4.50
6.00
–2.25
–4.50
–6.00
25
105
135
RL = 10kΩ, CL = 10pF
2.25
4.50
6.00
–2.25
–4.50
–6.00
35
145
190
fin = Sine Wave; Adjust fin Voltage to
Obtain 0dBm at VIS
fin = 10kHz, RL = 600Ω, CL = 50pF
2.25
4.50
6.00
–2.25
–4.50
–6.00
–50
–50
–50
fin = 1.0MHz, RL = 50Ω, CL = 10pF
2.25
4.50
6.00
–2.25
–4.50
–6.00
–60
–60
–60
Total Harmonic Distortion
(Figure 14)
fin = 1kHz, RL = 10kΩ, CL = 50pF
THD = THDmeasured – THDsource
VIS = 4.0VPP sine wave
VIS = 8.0VPP sine wave
VIS = 11.0VPP sine wave
Unit
25°C
fin = 1MHz Sine Wave; Adjust fin Voltage to
Obt i 0dBm
Obtain
0dB att VOS; Increase
I
fin
Frequency Until dB Meter Reads –3dB;
RL = 50Ω, CL = 10pF
Crosstalk Between Any Two
Switches (Figure 12)
(Test does not apply to HC4051A)
THD
Limit*
VEE
V
Maximum On–Channel Bandwidth
or Minimum
Mi i
Frequency
F
Response
R
(Figure 6)
Feedthrough Noise.
Channel–Select Input to Common
I/O (Figure 8)
—
VCC
V
Condition
‘51
‘52
‘53
80
80
80
95
95
95
120
120
120
MHz
dB
mVPP
dB
%
2.25
4.50
6.00
–2.25
–4.50
–6.00
0.10
0.08
0.05
*Limits not tested. Determined by design and verified by qualification.
180
160
250
Ron , ON RESISTANCE (OHMS)
Ron , ON RESISTANCE (OHMS)
300
200
125°C
150
25°C
– 55°C
100
50
140
120
125°C
100
80
25°C
60
– 55°C
40
20
0
0
0.25
0.5
0.75
1.0
1.25
1.5
1.75
2.0
0
2.25
0
0.25 0.5 0.75 1.0 1.25 1.5 1.75 2.0 2.25 2.5 2.75 3.0
VIS, INPUT VOLTAGE (VOLTS), REFERENCED TO VEE
VIS, INPUT VOLTAGE (VOLTS), REFERENCED TO VEE
Figure 1a. Typical On Resistance, VCC – VEE = 2.0 V
Figure 1b. Typical On Resistance, VCC – VEE = 3.0 V
http://onsemi.com
6
120
105
100
90
80
Ron , ON RESISTANCE (OHMS)
Ron , ON RESISTANCE (OHMS)
MC74HC4051A, MC74HC4052A, MC74HC4053A
125°C
60
25°C
40
– 55°C
20
0
75
125°C
60
25°C
45
– 55°C
30
15
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
0
4.5
0
0.5
Figure 1c. Typical On Resistance, VCC – VEE = 4.5 V
3.0 3.5
4.0
4.5 5.0 5.5 6.0
60
70
Ron , ON RESISTANCE (OHMS)
Ron , ON RESISTANCE (OHMS)
2.0 2.5
Figure 1d. Typical On Resistance, VCC – VEE = 6.0 V
80
60
50
125°C
40
30
25°C
20
– 55°C
10
0
–4.5
1.0 1.5
VIS, INPUT VOLTAGE (VOLTS), REFERENCED TO VEE
VIS, INPUT VOLTAGE (VOLTS), REFERENCED TO VEE
–3.5
–2.5
–1.5
–0.5
0.5
1.5
2.5
3.5
50
125°C
40
25°C
30
– 55°C
20
10
0
–6.0 –5.0 –4.0 –3.0 –2.0 –1.0
4.5
VIS, INPUT VOLTAGE (VOLTS), REFERENCED TO VEE
2.0
3.0 4.0
5.0
6.0
Figure 1f. Typical On Resistance, VCC – VEE = 12.0 V
PLOTTER
–
1.0
VIS, INPUT VOLTAGE (VOLTS), REFERENCED TO VEE
Figure 1e. Typical On Resistance, VCC – VEE = 9.0 V
PROGRAMMABLE
POWER
SUPPLY
0
MINI COMPUTER
DC ANALYZER
+
VCC
DEVICE
UNDER TEST
ANALOG IN
COMMON OUT
VEE
GND
Figure 2. On Resistance Test Set–Up
http://onsemi.com
7
MC74HC4051A, MC74HC4052A, MC74HC4053A
VCC
VCC
VCC
16
VEE
ANALOG I/O
OFF
A
VCC
VIH
OFF
VIH
6
7
8
VEE
COMMON O/I
6
7
8
VEE
Figure 3. Maximum Off Channel Leakage Current,
Any One Channel, Test Set–Up
VCC
Figure 4. Maximum Off Channel Leakage Current,
Common Channel, Test Set–Up
VCC
16
A
VEE
VCC
16
0.1µF
fin
ON
VOS
dB
METER
ON
N/C
COMMON O/I
OFF
VCC
OFF
VCC
COMMON O/I
OFF
NC
VCC
16
VEE
RL
CL*
ANALOG I/O
VIL
6
7
8
6
7
8
VEE
VEE
Figure 5. Maximum On Channel Leakage Current,
Channel to Channel, Test Set–Up
VCC
16
VIS
0.1µF
fin
Figure 6. Maximum On Channel Bandwidth,
Test Set–Up
VCC
16
VOS
dB
METER
OFF
RL
*Includes all probe and jig capacitance
CL*
RL
ON/OFF
COMMON O/I
ANALOG I/O
RL
OFF/ON
RL
RL
6
7
8
VEE
VIL or VIH
Vin ≤ 1 MHz
tr = tf = 6 ns
VEE
VCC
GND
CHANNEL SELECT
*Includes all probe and jig capacitance
6
7
8
TEST
POINT
CL*
VCC
11
CHANNEL SELECT
*Includes all probe and jig capacitance
Figure 7. Off Channel Feedthrough Isolation,
Test Set–Up
Figure 8. Feedthrough Noise, Channel Select to
Common Out, Test Set–Up
http://onsemi.com
8
MC74HC4051A, MC74HC4052A, MC74HC4053A
VCC
16
VCC
VCC
CHANNEL
SELECT
ON/OFF
50%
COMMON O/I
ANALOG I/O
OFF/ON
GND
tPLH
TEST
POINT
CL*
tPHL
ANALOG
OUT
6
7
8
50%
CHANNEL SELECT
*Includes all probe and jig capacitance
Figure 9a. Propagation Delays, Channel Select
to Analog Out
Figure 9b. Propagation Delay, Test Set–Up Channel
Select to Analog Out
VCC
16
ANALOG
IN
COMMON O/I
ANALOG I/O
VCC
ON
50%
TEST
POINT
CL*
GND
tPHL
tPLH
ANALOG
OUT
6
7
8
50%
*Includes all probe and jig capacitance
Figure 10a. Propagation Delays, Analog In
to Analog Out
tf
tr
90%
50%
10%
ENABLE
tPZL
ANALOG
OUT
Figure 10b. Propagation Delay, Test Set–Up
Analog In to Analog Out
tPLZ
1
VCC
2
GND
1
50%
TEST
POINT
ON/OFF
CL*
VOL
ENABLE
90%
1kΩ
ANALOG I/O
2
tPZH tPHZ
ANALOG
OUT
VCC
16
VCC
HIGH
IMPEDANCE
10%
POSITION 1 WHEN TESTING tPHZ AND tPZH
POSITION 2 WHEN TESTING tPLZ AND tPZL
VOH
50%
6
7
8
HIGH
IMPEDANCE
Figure 11a. Propagation Delays, Enable to
Analog Out
Figure 11b. Propagation Delay, Test Set–Up
Enable to Analog Out
http://onsemi.com
9
MC74HC4051A, MC74HC4052A, MC74HC4053A
VCC
VIS
A
VCC
16
RL
fin
16
VOS
ON
COMMON O/I
ON/OFF
NC
ANALOG I/O
0.1µF
OFF/ON
OFF
VEE
RL
RL
CL*
RL
CL*
6
7
8
VEE
VCC
6
7
8
11
CHANNEL SELECT
*Includes all probe and jig capacitance
Figure 12. Crosstalk Between Any Two
Switches, Test Set–Up
Figure 13. Power Dissipation Capacitance,
Test Set–Up
0
VIS
VCC
16
0.1µF
fin
– 10
VOS
ON
CL*
TO
DISTORTION
METER
– 30
– 40
dB
RL
FUNDAMENTAL FREQUENCY
– 20
– 50
DEVICE
– 60
6
7
8
VEE
SOURCE
– 70
– 80
– 90
*Includes all probe and jig capacitance
– 100
1.0
2.0
3.125
FREQUENCY (kHz)
Figure 14a. Total Harmonic Distortion, Test Set–Up
Figure 14b. Plot, Harmonic Distortion
APPLICATIONS INFORMATION
outputs to VCC or GND through a low value resistor helps
minimize crosstalk and feedthrough noise that may be
picked up by an unused switch.
Although used here, balanced supplies are not a
requirement. The only constraints on the power supplies are
that:
VCC – GND = 2 to 6 volts
VEE – GND = 0 to –6 volts
VCC – VEE = 2 to 12 volts
and VEE ≤ GND
When voltage transients above VCC and/or below VEE are
anticipated on the analog channels, external Germanium or
Schottky diodes (Dx) are recommended as shown in Figure
16. These diodes should be able to absorb the maximum
anticipated current surges during clipping.
The Channel Select and Enable control pins should be at
VCC or GND logic levels. VCC being recognized as a logic
high and GND being recognized as a logic low. In this
example:
VCC = +5V = logic high
GND = 0V = logic low
The maximum analog voltage swings are determined by
the supply voltages VCC and VEE. The positive peak analog
voltage should not exceed VCC. Similarly, the negative peak
analog voltage should not go below VEE. In this example,
the difference between VCC and VEE is ten volts. Therefore,
using the configuration of Figure 15, a maximum analog
signal of ten volts peak–to–peak can be controlled. Unused
analog inputs/outputs may be left floating (i.e., not
connected). However, tying unused analog inputs and
http://onsemi.com
10
MC74HC4051A, MC74HC4052A, MC74HC4053A
VCC
+5V
16
+5V
ANALOG
SIGNAL
–5V
ON
6
7
8
Dx
+5V
ANALOG
SIGNAL
VCC
16
Dx
Dx
VEE
VEE
7
8
–5V
VEE
Figure 15. Application Example
Figure 16. External Germanium or
Schottky Clipping Diodes
+5V
+5V
16
+5V
ANALOG
SIGNAL
VEE
ON/OFF
6
7
8
VEE
Dx
ON/OFF
–5V
TO EXTERNAL CMOS
CIRCUITRY 0 to 5V
DIGITAL SIGNALS
11
10
9
VCC
ANALOG
SIGNAL
+5V
*
R
R
11
10
9
+5V
+5V
VEE
VEE
16
ANALOG
SIGNAL
ON/OFF
+5V
ANALOG
SIGNAL
R
VEE
+5V
6
7
8
LSTTL/NMOS
CIRCUITRY
VEE
* 2K ≤ R ≤ 10K
a. Using Pull–Up Resistors
11
10
9
LSTTL/NMOS
CIRCUITRY
HCT
BUFFER
b. Using HCT Interface
Figure 17. Interfacing LSTTL/NMOS to CMOS Inputs
A
11
13
LEVEL
SHIFTER
14
B
10
15
LEVEL
SHIFTER
12
C
9
1
LEVEL
SHIFTER
5
ENABLE
6
2
LEVEL
SHIFTER
4
3
Figure 18. Function Diagram, HC4051A
http://onsemi.com
11
X0
X1
X2
X3
X4
X5
X6
X7
X
MC74HC4051A, MC74HC4052A, MC74HC4053A
A
10
12
LEVEL
SHIFTER
14
B
9
15
LEVEL
SHIFTER
11
13
ENABLE
6
1
LEVEL
SHIFTER
5
2
4
3
X0
X1
X2
X3
X
Y0
Y1
Y2
Y3
Y
Figure 19. Function Diagram, HC4052A
A
11
13
LEVEL
SHIFTER
12
14
B
10
1
LEVEL
SHIFTER
2
15
C
9
3
LEVEL
SHIFTER
5
4
ENABLE
6
LEVEL
SHIFTER
Figure 20. Function Diagram, HC4053A
http://onsemi.com
12
X1
X0
X
Y1
Y0
Y
Z1
Z0
Z
MC74HC4051A, MC74HC4052A, MC74HC4053A
ORDERING & SHIPPING INFORMATION
Package
Shipping
MC74HC4051AN
Device
PDIP–16
500 Units / Unit Pak
MC74HC4051AD
SOIC–16
48 Units / Rail
MC74HC4051ADR2
SOIC–16
2500 Units / Tape & Reel
MC74HC4051ADT
TSSOP–16
96 Units / Rail
MC74HC4051ADTR2
TSSOP–16
2500 Units / Tape & Reel
MC74HC4051ADW
SOIC WIDE
48 Units / Rail
MC74HC4051ADWR2
SOIC WIDE
1000 Units / Tape & Reel
MC74HC4051AF
SOEIAJ–16
See Note 1.
MC74HC4051AFEL
SOEIAJ–16
See Note 1.
MC74HC4052AN
PDIP–16
500 Units / Unit Pak
MC74HC4052AD
SOIC–16
48 Units / Rail
MC74HC4052ADR2
SOIC–16
2500 Units / Tape & Reel
MC74HC4052ADT
TSSOP–16
96 Units / Rail
MC74HC4052ADTR2
TSSOP–16
2500 Units / Tape & Reel
MC74HC4052ADW
SOIC WIDE
48 Units / Rail
MC74HC4052ADWR2
SOIC WIDE
1000 Units / Tape & Reel
MC74HC4052AF
SOEIAJ–16
See Note 1.
MC74HC4052AFEL
SOEIAJ–16
See Note 1.
MC74HC4053AN
PDIP–16
500 Units / Unit Pak
MC74HC4053AD
SOIC–16
48 Units / Rail
MC74HC4053ADR2
SOIC–16
2500 Units / Tape & Reel
MC74HC4053ADT
TSSOP–16
96 Units / Rail
MC74HC4053ADTR2
TSSOP–16
2500 Units / Tape & Reel
MC74HC4053ADW
SOIC WIDE
48 Units / Rail
MC74HC4053ADWR2
SOIC WIDE
1000 Units / Tape & Reel
MC74HC4053AF
SOEIAJ–16
See Note 1.
MC74HC4053AFEL
SOEIAJ–16
See Note 1.
1. For ordering information on the EIAJ version of the SOIC packages, please contact your local ON Semiconductor representative.
http://onsemi.com
13
MC74HC4051A, MC74HC4052A, MC74HC4053A
PACKAGE DIMENSIONS
PDIP–16
N SUFFIX
CASE 648–08
ISSUE R
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.
4. DIMENSION B DOES NOT INCLUDE MOLD FLASH.
5. ROUNDED CORNERS OPTIONAL.
–A
–
16
9
1
8
B
F
C
DIM
A
B
C
D
F
G
H
J
K
L
M
S
L
S
–T
–
SEATING
PLANE
K
H
D 16 PL
0.25 (0.010)
M
M
J
G
T A
M
INCHES
MILLIMETERS
MIN
MAX
MIN
MAX
0.740 0.770 18.80 19.55
0.250 0.270
6.85
6.35
0.145 0.175
4.44
3.69
0.015 0.021
0.53
0.39
0.040 0.070
1.77
1.02
0.100 BSC
2.54 BSC
0.050 BSC
1.27 BSC
0.008 0.015
0.38
0.21
0.110 0.130
3.30
2.80
0.295 0.305
7.74
7.50
10°
0°
10°
0°
0.020 0.040
1.01
0.51
SOIC–16
D SUFFIX
CASE 751B–05
ISSUE J
–A
–
16
9
1
8
–B
–
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
P 8 PL
0.25 (0.010)
M
B
M
G
K
F
R X 45°
C
–T
SEATING
–
PLANE
J
M
D 16 PL
0.25 (0.010)
M
T
B
S
A
S
http://onsemi.com
14
DIM
A
B
C
D
F
G
J
K
M
P
R
MILLIMETERS
MIN
MAX
9.80 10.00
4.00
3.80
1.75
1.35
0.49
0.35
1.25
0.40
1.27 BSC
0.25
0.19
0.25
0.10
7°
0°
6.20
5.80
0.50
0.25
INCHES
MIN
MAX
0.386 0.393
0.150 0.157
0.054 0.068
0.014 0.019
0.016 0.049
0.050 BSC
0.008 0.009
0.004 0.009
0°
7°
0.229 0.244
0.010 0.019
MC74HC4051A, MC74HC4052A, MC74HC4053A
PACKAGE DIMENSIONS
SOIC–16 WIDE
DW SUFFIX
CASE 751G–03
ISSUE B
A
D
9
1
8
NOTES:
1. DIMENSIONS ARE IN MILLIMETERS.
2. INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.5M, 1994.
3. DIMENSIONS D AND E DO NOT INLCUDE MOLD
PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE.
5. DIMENSION B DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.13 TOTAL IN EXCESS
OF THE B DIMENSION AT MAXIMUM MATERIAL
CONDITION.
h X 45 _
H
E
0.25
8X
M
B
M
16
q
B
B
16X
M
T A
14X
e
S
B
S
L
A
0.25
DIM
A
A1
B
C
D
E
e
H
h
L
A1
SEATING
PLANE
q
C
T
MILLIMETERS
MIN
MAX
2.35
2.65
0.10
0.25
0.35
0.49
0.23
0.32
10.15
10.45
7.40
7.60
1.27 BSC
10.05
10.55
0.25
0.75
0.50
0.90
0_
7_
TSSOP–16
DT SUFFIX
CASE 948F–01
ISSUE O
16X K REF
0.10 (0.004)
0.15 (0.006) T U
M
T U
V
S
S
S
K
ÉÉÉ
ÇÇÇ
ÇÇÇ
ÉÉÉ
ÇÇÇ
K1
2X
L/2
16
9
J1
B
–U–
L
SECTION N–N
J
PIN 1
IDENT.
8
1
N
0.25 (0.010)
0.15 (0.006) T U
S
A
–V–
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD FLASH.
PROTRUSIONS OR GATE BURRS. MOLD FLASH OR
GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER
SIDE.
4. DIMENSION B DOES NOT INCLUDE INTERLEAD
FLASH OR PROTRUSION. INTERLEAD FLASH OR
PROTRUSION SHALL NOT EXCEED
0.25 (0.010) PER SIDE.
5. DIMENSION K DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR PROTRUSION
SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K
DIMENSION AT MAXIMUM MATERIAL CONDITION.
6. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
7. DIMENSION A AND B ARE TO BE DETERMINED AT
DATUM PLANE –W–.
M
N
F
DETAIL E
–W–
C
0.10 (0.004)
–T– SEATING
PLANE
DETAIL E
H
D
G
http://onsemi.com
15
DIM
A
B
C
D
F
G
H
J
J1
K
K1
L
M
MILLIMETERS
MIN
MAX
4.90
5.10
4.30
4.50
–––
1.20
0.05
0.15
0.50
0.75
0.65 BSC
0.18
0.28
0.09
0.20
0.09
0.16
0.19
0.30
0.19
0.25
6.40 BSC
0_
8_
INCHES
MIN
MAX
0.193
0.200
0.169
0.177
–––
0.047
0.002
0.006
0.020
0.030
0.026 BSC
0.007
0.011
0.004
0.008
0.004
0.006
0.007
0.012
0.007
0.010
0.252 BSC
0_
8_
MC74HC4051A, MC74HC4052A, MC74HC4053A
PACKAGE DIMENSIONS
SOEIAJ–16
F SUFFIX
PLASTIC EIAJ SOIC PACKAGE
CASE 966–01
ISSUE O
16
LE
9
Q1
M_
E HE
1
L
8
DETAIL P
Z
D
e
VIEW P
A
A1
b
0.13 (0.005)
c
M
0.10 (0.004)
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS D AND E DO NOT INCLUDE
MOLD FLASH OR PROTRUSIONS AND ARE
MEASURED AT THE PARTING LINE. MOLD FLASH
OR PROTRUSIONS SHALL NOT EXCEED 0.15
(0.006) PER SIDE.
4. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
5. THE LEAD WIDTH DIMENSION (b) DOES NOT
INCLUDE DAMBAR PROTRUSION. ALLOWABLE
DAMBAR PROTRUSION SHALL BE 0.08 (0.003)
TOTAL IN EXCESS OF THE LEAD WIDTH
DIMENSION AT MAXIMUM MATERIAL CONDITION.
DAMBAR CANNOT BE LOCATED ON THE LOWER
RADIUS OR THE FOOT. MINIMUM SPACE
BETWEEN PROTRUSIONS AND ADJACENT LEAD
TO BE 0.46 ( 0.018).
DIM
A
A1
b
c
D
E
e
HE
L
LE
M
Q1
Z
MILLIMETERS
MIN
MAX
–––
2.05
0.05
0.20
0.35
0.50
0.18
0.27
9.90
10.50
5.10
5.45
1.27 BSC
7.40
8.20
0.50
0.85
1.10
1.50
10 _
0_
0.70
0.90
–––
0.78
INCHES
MIN
MAX
–––
0.081
0.002
0.008
0.014
0.020
0.007
0.011
0.390
0.413
0.201
0.215
0.050 BSC
0.291
0.323
0.020
0.033
0.043
0.059
10 _
0_
0.028
0.035
–––
0.031
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes
without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular
purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability,
including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be
validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others.
SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or
death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold
SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable
attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.
PUBLICATION ORDERING INFORMATION
NORTH AMERICA Literature Fulfillment:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada
Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada
Email: [email protected]
Fax Response Line: 303–675–2167 or 800–344–3810 Toll Free USA/Canada
N. American Technical Support: 800–282–9855 Toll Free USA/Canada
EUROPE: LDC for ON Semiconductor – European Support
German Phone: (+1) 303–308–7140 (M–F 1:00pm to 5:00pm Munich Time)
Email: ONlit–[email protected]
French Phone: (+1) 303–308–7141 (M–F 1:00pm to 5:00pm Toulouse Time)
Email: ONlit–[email protected]
English Phone: (+1) 303–308–7142 (M–F 12:00pm to 5:00pm UK Time)
Email: [email protected]
EUROPEAN TOLL–FREE ACCESS*: 00–800–4422–3781
*Available from Germany, France, Italy, England, Ireland
CENTRAL/SOUTH AMERICA:
Spanish Phone: 303–308–7143 (Mon–Fri 8:00am to 5:00pm MST)
Email: ONlit–[email protected]
ASIA/PACIFIC: LDC for ON Semiconductor – Asia Support
Phone: 303–675–2121 (Tue–Fri 9:00am to 1:00pm, Hong Kong Time)
Toll Free from Hong Kong & Singapore:
001–800–4422–3781
Email: ONlit–[email protected]
JAPAN: ON Semiconductor, Japan Customer Focus Center
4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–8549
Phone: 81–3–5740–2745
Email: [email protected]
ON Semiconductor Website: http://onsemi.com
For additional information, please contact your local
Sales Representative.
http://onsemi.com
16
MC74HC4051A/D