NLX2G06 Dual Inverter, Open Drain The NLX2G06 MiniGatet is an advanced high-speed CMOS dual inverter with open drain output in ultra-small footprint. The NLX2G06 input and output structures provide protection when voltages up to 7.0 V are applied, regardless of the supply voltage. http://onsemi.com Features •High Speed: tPD = 2.4 ns (Typ) @ VCC = 5.0 V •Low Power Dissipation: ICC = 1 mA (Max) at TA = 25°C •Power Down Protection Provided on inputs •Balanced Propagation Delays •Overvoltage Tolerant (OVT) Input and Output Pins •Ultra-Small Packages •These are Pb-Free Devices MARKING DIAGRAMS 1 IN A1 1 6 5 2 VCC 1 P M 3 IN A2 4 M OUT Y1 ULLGA6 1.45 x 1.0 CASE 613AF GND M P ULLGA6 1.2 x 1.0 CASE 613AE M P 1 P ULLGA6 1.0 x 1.0 CASE 613AD = Device Marking = Date Code OUT Y2 PIN ASSIGNMENT Figure 1. Pinout (Top View) IN A1 1 OUT Y1 IN A2 1 OUT Y2 1 IN A1 2 GND 3 IN A2 4 OUT Y2 5 VCC 6 OUT Y1 Figure 2. Logic Symbol FUNCTION TABLE A Y L H Z L ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 5 of this data sheet. © Semiconductor Components Industries, LLC, 2008 March, 2008 - Rev. 0 1 Publication Order Number: NLX2G06/D NLX2G06 MAXIMUM RATINGS Symbol Value Unit VCC DC Supply Voltage -0.5 to +7.0 V VIN DC Input Voltage -0.5 to +7.0 V DC Output Voltage -0.5 to +7.0 V VIN < GND -50 mA VOUT < GND -50 mA VOUT Parameter IIK DC Input Diode Current IOK DC Output Diode Current IO DC Output Source/Sink Current ±50 mA ICC DC Supply Current Per Supply Pin ±100 mA IGND DC Ground Current per Ground Pin ±100 mA TSTG Storage Temperature Range -65 to +150 °C TL Lead Temperature, 1 mm from Case for 10 Seconds 260 °C TJ Junction Temperature Under Bias 150 °C MSL FR ILATCHUP Moisture Sensitivity Level 1 Flammability Rating Oxygen Index: 28 to 34 UL 94 V-0 @ 0.125 in Latchup Performance Above VCC and Below GND at 125 °C (Note 5) ±500 mA Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. Measured with minimum pad spacing on an FR4 board, using 10 mm-by-1 inch, 2 ounce copper trace no air flow. 2. Tested to EIA/JESD22-A114-A. 3. Tested to EIA/UESD22-A115-A. 4. Tested to JESD22-C101-A. 5. Tested to EIA / JESD78. RECOMMENDED OPERATING CONDITIONS Symbol Parameter Min Max Unit 1.65 5.5 V VCC Positive DC Supply Voltage VIN Digital Input Voltage 0 5.5 V Output Voltage 0 5.5 V -55 +125 °C 0 0 0 20 10 5 ns/V VOUT TA Operating Free-Air Temperature Dt/DV Input Transition Rise or Fall Rate VCC = 2.5 V ± 0.2 V VCC = 3.3 V ± 0.3 V VCC = 5.0 V ± 0.5 V http://onsemi.com 2 NLX2G06 DC ELECTRICAL CHARACTERISTICS VCC (V) Min Typ TA = +855C Max Min Max TA = -555C to +1255C Min Max Symbol Parameter VIH Low-Level Input Voltage 1.65-1.95 0.75 x VCC 0.75 x VCC 0.75 x VCC 2.3 to 5.5 0.70 x VCC 0.70 x VCC 0.70 x VCC Low-Level Input Voltage 1.65-1.95 0.25 x VCC 0.25 x VCC 0.25 x VCC 2.3 - 5.5 0.30 x VCC 0.30 x VCC 0.30 x VCC 1.65 - 5.5 0.1 0.1 0.1 0.24 0.3 0.4 0.4 0.55 0.55 0.24 0.3 0.4 0.4 0.55 0.55 0.24 0.3 0.4 0.4 0.55 0.55 5.5 ±5.0 ±10 ±10 mA 0 to 5.5 ±0.1 ±1.0 ±1.0 mA 0 1.0 10 10 mA 5.5 1.0 10 10 mA VIL VOL Low-Level Output Voltage Conditions TA = 25 5C VIN = VIH or VIL IOL = 100 mA VIN = VIH or VIL IOH = 4 mA IOH = 8 mA IOH = 12 mA IOH = 16 mA IOH = 24 mA IOH = 32 mA ILKG Z-State Output Leakage Current VIN = VIL, VOUT = VCC or GND IIN Input Leakage Current 0 v VIN v 5.5 V IOFF Power-Off Output Leakage Current VIN or VOUT = 5.5 V ICC Quiescent Supply Current 0 v VIN v VCC 1.65 2.3 2.7 3.0 3.0 4.5 0.08 0.2 0.22 0.28 0.38 0.42 http://onsemi.com 3 Unit V V V NLX2G06 AC ELECTRICAL CHARACTERISTICS (Input tr = tf = 3.0 nS) VCC (V) Test Condition 1.65-1.95 TA = -555C to +1255C TA = 25 5C Min Typ Max Min Max Unit RL = R1 = 5000 W, CL = 15 pF 2.0 5.7 10.5 2.0 11 ns 2.3-2.7 RL = R1 = 500 W, CL = 50 pF 0.8 3.0 3.6 0.8 4.1 3.0-3.6 RL = R1 = 500 W, CL = 50 pF 0.8 2.4 3.2 0.8 3.7 4.5-5.5 RL = R1 = 500 W, CL = 50 pF 0.5 2.4 3.0 0.5 3.5 1.65-1.95 RL = R1 = 5000 W, CL = 15 pF 2.0 5.7 10.5 2.0 11 2.3-2.7 RL = R1 = 500 W, CL = 50 pF 0.8 3.8 3.6 0.8 4.1 3.0-3.6 RL = R1 = 500 W, CL = 50 pF 0.8 2.9 3.2 0.8 3.7 4.5-5.5 RL = R1 = 500 W, CL = 50 pF 0.5 1.2 3.0 0.5 3.5 Input Capacitance 5.5 VIN = 0 V or VCC 2.5 pF COUT Output Capacitance 5.5 VIN = 0 V or VCC 4 pF CPD Power Dissipation Capacitance (Note 6) 3.3 5.5 10 MHz VIN = 0 V or VCC 4 pF Symbol tPZL tPLZ CIN Parameter Propagation Delay (Figures 3 and 4) Propagation Delay (Figures 3 and 4) ns 6. CPD is defined as the value of the internal equivalent capacitance which is calculated from the dynamic operating current consumption without load. Average operating current can be obtained by the equation ICC(OPR) = CPD • VCC • fin + ICC. CPD is used to determine the no-load dynamic power consumption: PD = CPD • VCC2 • fin + ICC • VCC. VCC A 50% GND tPZL Y tPLZ 50% VCC HIGH IMPEDANCE VOL +0.3 V Figure 3. Switching Waveforms VCC R1 PULSE GENERATOR DUT RT CL RT = ZOUT of pulse generator (typically 50 W) Figure 4. Test Circuit http://onsemi.com 4 RL VCC x 2 NLX2G06 ORDERING INFORMATION Package Shipping† NLX2G06AMX1TCG ULLGA6, 1.45 x 1.0, 0.5P (Pb-Free) 3000 / Tape & Reel NLX2G06BMX1TCG ULLGA6, 1.2 x 1.0, 0.4P (Pb-Free) 3000 / Tape & Reel NLX2G06CMX1TCG ULLGA6, 1.0 x 1.0, 0.35P (Pb-Free) 3000 / Tape & Reel Device †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 5 NLX2G06 PACKAGE DIMENSIONS ULLGA6 1.0x1.0, 0.35P CASE 613AD-01 ISSUE A PIN ONE REFERENCE 0.10 C ÉÉ ÉÉ ÉÉ 0.10 C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.30 mm FROM THE TERMINAL TIP. 4. A MAXIMUM OF 0.05 PULL BACK OF THE PLATED TERMINAL FROM THE EDGE OF THE PACKAGE IS ALLOWED. A B D E DIM A A1 b D E e L L1 TOP VIEW 0.05 C A 6X 0.05 C SEATING PLANE SIDE VIEW MOUNTING FOOTPRINT SOLDERMASK DEFINED* C A1 MILLIMETERS MIN MAX --0.40 0.00 0.05 0.12 0.22 1.00 BSC 1.00 BSC 0.35 BSC 0.25 0.35 0.30 0.40 5X 0.48 6X 0.22 e 5X L NOTE 4 3 1 1.18 L1 0.53 6 4 6X b 0.05 C 0.35 PITCH DIMENSIONS: MILLIMETERS 0.10 C A B BOTTOM VIEW 1 PKG OUTLINE *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. NOTE 3 http://onsemi.com 6 NLX2G06 PACKAGE DIMENSIONS ULLGA6 1.2x1.0, 0.4P CASE 613AE-01 ISSUE A PIN ONE REFERENCE 0.10 C ÉÉ ÉÉ ÉÉ 0.10 C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.30 mm FROM THE TERMINAL TIP. 4. A MAXIMUM OF 0.05 PULL BACK OF THE PLATED TERMINAL FROM THE EDGE OF THE PACKAGE IS ALLOWED. A B D E DIM A A1 b D E e L L1 TOP VIEW 0.05 C A 6X 0.05 C SEATING PLANE SIDE VIEW MOUNTING FOOTPRINT SOLDERMASK DEFINED* C A1 MILLIMETERS MIN MAX --0.40 0.00 0.05 0.15 0.25 1.20 BSC 1.00 BSC 0.40 BSC 0.25 0.35 0.35 0.45 5X 0.49 e 5X L NOTE 4 3 1 6X 0.26 1.24 L1 0.53 6 4 6X b 0.05 C NOTE 3 0.40 PITCH DIMENSIONS: MILLIMETERS 0.10 C A B BOTTOM VIEW 1 PKG OUTLINE *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 7 NLX2G06 PACKAGE DIMENSIONS ULLGA6 1.45x1.0, 0.5P CASE 613AF-01 ISSUE A PIN ONE REFERENCE 0.10 C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.30 mm FROM THE TERMINAL TIP. 4. A MAXIMUM OF 0.05 PULL BACK OF THE PLATED TERMINAL FROM THE EDGE OF THE PACKAGE IS ALLOWED. A B D ÉÉÉ ÉÉÉ ÉÉÉ E DIM A A1 b D E e L L1 TOP VIEW 0.10 C 0.05 C MILLIMETERS MIN MAX --0.40 0.00 0.05 0.15 0.25 1.45 BSC 1.00 BSC 0.50 BSC 0.25 0.35 0.30 0.40 A 6X 0.05 C MOUNTING FOOTPRINT SOLDERMASK DEFINED* SEATING PLANE SIDE VIEW 5X C A1 e 5X L 0.49 NOTE 4 3 1 6X 0.30 1.24 L1 0.53 6 4 BOTTOM VIEW 6X b 0.10 C A B 0.05 C NOTE 3 1 PKG OUTLINE 0.50 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. MiniGate is a trademark of Semiconductor Components Industries, LLC (SCILLC). ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 http://onsemi.com 8 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NLX2G06/D