ONSEMI NCV4279BDWR2

NCV4279B
5.0 V Micropower 150 mA
LDO Linear Regulator with
DELAY, Adjustable RESET,
and Monitor FLAG
The NCV4279B is a 5.0 V precision micropower voltage regulator.
The output current capability is 150 mA.
The output voltage is accurate within ±2.0% with a maximum
dropout voltage of 0.6 V at 150 mA. Low quiescent current is a feature
drawing only 90 A with a 100 A load. This part is ideal for any and
all battery operated microprocessor equipment.
Microprocessor control logic includes an active RESET (with
DELAY), and a FLAG monitor which can be used to provide an early
warning signal to the microprocessor of a potential impending RESET
signal. The use of the FLAG monitor allows the microprocessor to
finish any signal processing before the RESET shuts the
microprocessor down.
The active RESET circuit operates correctly at an output voltage as
low as 1.0 V. The RESET function is activated during the power up
sequence or during normal operation if the output voltage drops
outside the regulation limits.
The reset threshold voltage can be decreased by the connection of
external resistor divider to RADJ lead.
The regulator is protected against reverse battery, short circuit, and
thermal overload conditions. The device can withstand load dump
transients making it suitable for use in automotive environments. The
device has also been optimized for EMC conditions.
http://onsemi.com
MARKING DIAGRAMS
8
8
1
4279B
ALYW
14
SO−14
D SUFFIX
CASE 751A
14
1
1
NCV4279B
AWLYWW
1
20
20
NCV4279B
AWLYYWW
SO−20L
DW SUFFIX
CASE 751D
1
A
WL, L
YY, Y
WW, W
1
= Assembly Location
= Wafer Lot
= Year
= Work Week
PIN CONNECTIONS
SO−8
Features
• 5.0 V ± 2.0% Output
• Low 90 A Quiescent Current
• Active RESET
• Adjustable Reset
• 150 mA Output Current Capability
• Fault Protection
− +60 V Peak Transient Voltage
− −15 V Reverse Voltage
− Short Circuit
− Thermal Overload
• Early Warning through FLAG/MON Leads
• Internally Fused Leads in SO−14 and SO−20L Packages
• NCV Prefix for Automotive and Other Applications Requiring Site
and Control Changes
SO−8
D SUFFIX
CASE 751
VIN
1
8
MON
RADJ
FLAG
RESET
DELAY
SO−14
SO−20L
GND
1
RADJ
DELAY
GND
GND
GND
NC
RESET
14
MON
VIN
GND
GND
GND
VOUT
FLAG
1
RADJ
DELAY
NC
GND
GND
GND
GND
NC
NC
RESET
VOUT
20
MON
VIN
NC
GND
GND
GND
GND
NC
VOUT
FLAG
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 10 of this data sheet.
 Semiconductor Components Industries, LLC, 2003
August, 2003 − Rev. 1
1
Publication Order Number:
NCV4279B/D
NCV4279B
VIN
VOUT
VDD
10 µF
10 µF
RADJ
NCV4279B
Delay
RFLG
10 k
Microprocessor
VBAT
RRST
10 k
MON
CDELAY
RESET
FLAG
I/O
GND
I/O
Figure 1. Application Diagram
MAXIMUM RATINGS*
Rating
Value
Unit
−15 to 45
V
Peak Transient Voltage (46 V Load Dump @ VIN = 14 V)
60
V
Operating Voltage
45
V
VOUT (DC)
16
V
Voltage Range (RESET, FLAG)
−0.3 to 10
V
Input Voltage Range (MON)
−0.3 to 10
V
2.0
kV
Junction Temperature, TJ
−40 to +150
°C
Storage Temperature, TS
−55 to 150
°C
VIN (DC)
ESD Susceptibility (Human Body Model)
°C/W
Package Thermal Resistance, SO−8:
Junction−to−Case, RθJC
Junction−to−Ambient, RθJA
45
165
Package Thermal Resistance, SO−14 (Fused) Minimum Pad Data:
Junction−to−Case, RθJC
Junction−to−Ambient, RθJA
Junction−to−Pin, RθJP (Note 3)
15
110
33
Package Thermal Resistance, SO−20L (Fused) Minimum Pad Data:
Junction−to−Case, RθJC
Junction−to−Ambient, RθJA
Junction−to−Pin, RθJP (Note 4)
12
82
26
°C/W
Lead Temperature Soldering:
°C/W
Reflow: (SMD styles only) (Notes 1, 2)
240 peak
°C
1. 60 second maximum above 183°C.
2. −5°C/+0°C allowable conditions.
3. Measured to pin 9.
4. Measured to pin 12.
*The maximum package power dissipation must be observed.
†During the voltage range which exceeds the maximum tested voltage of VIN, operation is assured, but not specified. Wider limits may apply.
Thermal dissipation must be observed closely.
http://onsemi.com
2
NCV4279B
ELECTRICAL CHARACTERISTICS (IOUT = 1.0 mA, −40°C ≤ TJ ≤ 125°C; 6.0 V < VIN < 26 V; unless otherwise specified.)
Test Conditions
Characteristic
Min
Typ
Max
Unit
4.90
4.85
5.0
5.0
5.10
5.15
V
V
−
−
400
100
600
150
mV
mV
-30
5.0
30
mV
Output Stage
Output Voltage
9.0 V < VIN < 16 V, 100 A ≤ IOUT ≤ 150 mA
6.0 V < VIN < 26 V, 100 A ≤ IOUT ≤ 150 mA
Dropout Voltage (VIN − VOUT)
IOUT = 150 mA
IOUT = 100 A
Load Regulation
VIN = 14 V, 5.0 mA ≤ IOUT ≤ 150 mA
Line Regulation
[VOUT(typ) + 1.0] < VIN < 26 V, IOUT = 1.0 mA
−
15
60
mV
Quiescent Current, (IQ)
Active Mode
IOUT = 100 A, VIN = 12 V, Delay = 3.0 V, MON = 3.0 V
IOUT = 75 mA, VIN = 14 V, Delay = 3.0 V, MON = 3.0 V
IOUT ≤ 150 mA, VIN = 14 V, Delay = 3.0 V, MON = 3.0 V
−
−
−
90
4.0
12
125
6.0
19
A
mA
mA
−
151
300
−
mA
Current Limit
Short Circuit Output Current
VOUT = 0 V
40
190
−
mA
Thermal Shutdown
(Guaranteed by Design)
150
180
−
°C
RESET Threshold
HIGH (VRH)
LOW (VRL)
VOUT Increasing
VOUT Decreasing
4.55
4.50
4.70
4.60
0.98 × VOUT
0.97 × VOUT
V
V
Output Voltage
Low (VRLO)
1.0 V ≤ VOUT ≤ VRL, RRESET = 10 k
−
0.1
0.4
V
1.4
1.8
2.2
V
−
−
0.1
V
Reset Function (RESET)
Delay Switching Threshold (VDT)
−
Reset Delay Low Voltage
VOUT < RESET Threshold Low(min)
Delay Charge Current
DELAY = 1.0 V, VOUT > VRH
1.5
2.5
3.5
A
Delay Discharge Current
DELAY = 1.0 V, VOUT = 1.5 V
5.0
−
−
mA
−
1.23
1.31
1.39
V
Increasing and Decreasing
1.10
1.20
1.31
V
20
50
100
mV
−0.5
0.1
0.5
A
−
0.1
0.4
V
Reset Adjust Switching Voltage
(VR(ADJ))
FLAG/Monitor
Monitor Threshold
Hysteresis
−
Input Current
MON = 2.0 V
Output Saturation Voltage
MON = 0 V, IFLAG = 1.0 mA
http://onsemi.com
3
NCV4279B
PACKAGE PIN DESCRIPTION
Package Pin Number
SO−8
SO−14
SO−20L
Pin Symbol
3
1
1
RADJ
4
2
2
DELAY
5
3−5, 10−12
4−7, 14−17
GND
−
6
3, 8, 9, 13, 18
NC
6
7
10
RESET
7
8
11
FLAG
Open collector output from early warning comparator.
8
9
12
VOUT
±2.0%, 150 mA output.
1
13
19
VIN
2
14
20
MON
Function
Reset Adjust. If not needed connect to ground.
Timing capacitor for RESET function.
Ground. All GND leads must be connected to Ground.
No connection.
Active reset (accurate to VOUT ≥ 1.0 V)
Input Voltage.
Monitor. Input for early warning comparator. If not needed connect to VOUT.
TYPICAL PERFORMANCE CHARACTERISTICS
5.01
1.2
VIN = 12 V
VOUT = 5.0 V
VIN = 14 V
IOUT = 5.0 mA
1.0
5.00
+125°C
IQ (mA)
VOUT (V)
0.8
4.99
+25°C
0.6
−40°C
0.4
0.2
4.98
−40 −25 −10
5
20 35 50 65
Temperature (°C)
80
0
95 110 125
Figure 2. Output Voltage vs. Temperature
5
0
10
15
IOUT (mA)
20
Figure 3. Quiescent Current vs. Output Current
14
7
VIN = 12 V
T = 25°C
12
6
10
8
IOUT = 100 mA
5
+125°C
IQ (mA)
IQ (mA)
25
+25°C
6
4
3
−40°C
4
2
2
1
0
0
0
15
30
45
60 75 90
IOUT (mA)
105 120 135 140
IOUT = 50 mA
IOUT = 10 mA
6
8
10
12
14
16 18
VIN (V)
20
22
24
Figure 5. Quiescent Current vs. Input Voltage
Figure 4. Quiescent Current vs. Output Current
http://onsemi.com
4
26
NCV4279B
TYPICAL PERFORMANCE CHARACTERISTICS
120
450
T = 25°C
100
400
Dropout Voltage (mV)
IOUT = 100 A
IQ (µA)
80
60
49
20
0
350
300
+125°C
+25°C
250
−40°C
200
150
100
50
6
8
10
12
14
16 18
VIN (V)
20
22
24
0
26
0
Figure 6. Quiescent Current vs. Input Voltage
25
50
75
IOUT (mA)
100
125
150
Figure 7. Dropout Voltage vs. Output Current
1000
1000
Unstable Region
Unstable Region
CVout = 10 F
100
CVout = 0.1 F
ESR ()
ESR ()
100
10
10
1
Stable Region
Stable Region
0.1
CVout = 10 F
1
0.01
0
0 10 20 30 40 50 60 70 80 90 100110120130140150
OUTPUT CURRENT (mA)
10
20
30
40
50
60
70
80
90
100 110
OUTPUT CURRENT (mA)
Figure 8. Output Capacitor ESR
Figure 9. Output Stability with Output
Capacitor Change
http://onsemi.com
5
NCV4279B
VOUT
VIN
Current Source
(Circuit Bias)
IBIAS
Current Limit
Sense
+
+
−
RADJ
IBIAS
+ −
VBG
Error Amplifier
RESET
VBG
+
−
1.8 V
Thermal
Protection
3.0 µA
Delay
IBIAS
Bandgap
Reference
VBG
VBG
IBIAS
+
−
MON
Figure 10. Block Diagram
http://onsemi.com
6
GND
FLAG
NCV4279B
CIRCUIT DESCRIPTION
DELAY Function
REGULATOR CONTROL FUNCTIONS
The NCV4279B contains the microprocessor compatible
control function RESET (Figure 11).
The reset delay circuit provides a programmable (by
external capacitor) delay on the RESET output lead.
The DELAY lead provides source current (typically
2.5 A) to the external DELAY capacitor during the
following proceedings:
1. During Power Up (once the regulation threshold
has been verified).
2. After a reset event has occurred and the device is
back in regulation. The DELAY capacitor is
discharged when the regulation (RESET threshold)
has been violated. This is a latched incident. The
capacitor will fully discharge and wait for the
device to regulate before going through the delay
time event again.
VIN
RESET
Threshold
VOUT
DELAY
DELAY
Threshold
(VDT)
RESET
Td
Td
Figure 11. Reset and Delay Circuit Wave Forms
RESET Function
FLAG/Monitor Function
A RESET signal (low voltage) is generated as the IC
powers up until VOUT is within 6.0% of the regulated output
voltage, or when VOUT drops out of regulation,and is lower
than 8.0% below the regulated output voltage. Hysteresis is
included in the function to minimize oscillations.
The RESET output is an open collector NPN transistor,
controlled by a low voltage detection circuit. The circuit is
functionally independent of the rest of the IC thereby
guaranteeing that the RESET signal is valid for VOUT as low
as 1.0 V.
An on−chip comparator is provided to perform an early
warning to the microprocessor of a possible reset signal. The
reset signal typically turns the microprocessor off
instantaneously. This can cause unpredictable results with
the microprocessor. The signal received from the FLAG pin
will allow the microprocessor time to complete its present
task before shutting down. This function is performed by a
comparator referenced to the bandgap reference. The actual
trip point can be programmed externally using a resistor
divider to the input monitor (MON) (Figure 13). The typical
threshold is 1.20 V on the MON Pin.
Adjustable Reset Function
The reset threshold can be made lower by connecting an
external resistor divider to the RADJ lead from the VOUT
lead, as displayed in Figure 12. This lead is grounded to
select the default value of 4.6 V.
NCV4279B
Delay
RRST
RESET
VOUT
VIN
NCV4279B
to µP and
System
Power
VOUT
RADJ
VBAT
COUT
MON
FLAG
RADJ
RESET
Delay
GND
VCC
µP
COUT
I/O
RESET
Figure 13. FLAG/Monitor Function
to µP and
RESET
Port
CDELAY
Figure 12. Adjustable RESET
http://onsemi.com
7
NCV4279B
APPLICATION NOTES
FLAG MONITOR
Figure 14 shows the FLAG Monitor waveforms as a result
of the circuit depicted in Figure 13. As the output voltage
falls (VOUT), the Monitor threshold is crossed. This causes
the voltage on the FLAG output to go low sending a warning
signal to the microprocessor that a RESET signal may occur
in a short period of time. TWARNING is the time the
microprocessor has to complete the function it is currently
working on and get ready for the RESET shutdown signal.
The value for the output capacitor COUT shown in Figure 15
should work for most applications, however it is not
necessarily the optimized solution.
VIN
VOUT
CIN*
0.1 F
NCV4279B
COUT**
10 F
RRST
RESET
VOUT
*CIN required if regulator is located far from the power supply filter.
**COUT required for stability. Capacitor must operate at minimum
temperature expected.
MON
FLAG Monitor
Ref. Voltage
Figure 15. Test and Application Circuit Showing
Output Compensation
RESET
CALCULATING POWER DISSIPATION IN A
SINGLE OUTPUT LINEAR REGULATOR
The maximum power dissipation for a single output
regulator (Figure 16) is:
FLAG
PD(max) [VIN(max) VOUT(min)] IOUT(max)
VIN(max)IQ
TWARNING
where:
VIN(max) is the maximum input voltage,
VOUT(min) is the minimum output voltage,
IOUT(max) is the maximum output current for the
application, and
IQ is the quiescent current the regulator consumes at
IOUT(max).
Once the value of PD(max) is known, the maximum
permissible value of RJA can be calculated:
Figure 14. FLAG Monitor Circuit Waveform
SETTING THE DELAY TIME
The delay time is controlled by the Reset Delay Low
Voltage, Delay Switching Threshold, and the Delay Charge
Current. The delay follows the equation:
tDELAY [CDELAY(Vdt Reset Delay Low Voltage)]
Delay Charge Current
Example:
Using CDELAY = 33 nF.
Assume reset Delay Low Voltage = 0.
Use the typical value for Vdt = 1.8 V.
Use the typical value for Delay Charge Current = 2.5 A.
tDELAY (1)
T
RJA 150°C A
PD
(2)
The value of RJA can then be compared with those in the
package section of the data sheet. Those packages with
RJA’s less than the calculated value in equation 2 will keep
the die temperature below 150°C.
In some cases, none of the packages will be sufficient to
dissipate the heat generated by the IC, and an external
heatsink will be required.
[33 nF(1.8 0)]
23.8 ms
2.5 A
STABILITY CONSIDERATIONS
The output or compensation capacitor helps determine
three main characteristics of a linear regulator: start−up
delay, load transient response and loop stability.
The capacitor value and type should be based on cost,
availability, size and temperature constraints. A tantalum or
aluminum electrolytic capacitor is best, since a film or
ceramic capacitor with almost zero ESR can cause
instability. The aluminum electrolytic capacitor is the least
expensive solution, but, if the circuit operates at low
temperatures (−25°C to −40°C), both the value and ESR of
the capacitor will vary considerably. The capacitor
manufacturers data sheet usually provides this information.
IOUT
IIN
VIN
SMART
REGULATOR
VOUT
} Control
Features
IQ
Figure 16. Single Output Regulator with Key
Performance Parameters Labeled
http://onsemi.com
8
NCV4279B
HEAT SINKS
A heat sink effectively increases the surface area of the
package to improve the flow of heat away from the IC and
into the surrounding air.
Each material in the heat flow path between the IC and the
outside environment will have a thermal resistance. Like
series electrical resistances, these resistances are summed to
determine the value of RJA:
RJA RJC RCS RSA
where:
RJC = the junction−to−case thermal resistance,
RCS = the case−to−heatsink thermal resistance, and
RSA = the heatsink−to−ambient thermal resistance.
RJC appears in the package section of the data sheet. Like
RJA, it too is a function of package type. RCS and RSA are
functions of the package type, heatsink and the interface
between them. These values appear in heat sink data sheets
of heat sink manufacturers.
(3)
http://onsemi.com
9
NCV4279B
ORDERING INFORMATION
Device
Output Voltage
Package
NCV4279BD1
98 Units/Rail
SO 8
SO−8
NCV4279BD1R2
NCV4279BD2
NCV4279BD2R2
Shipping
2500 Tape & Reel
55 Units/Rail
50V
5.0
SO 14
SO−14
NCV4279BDW
1000 Tape & Reel
37 Units/Rail
SO 20L
SO−20L
NCV4279BDWR2
http://onsemi.com
10
1000 Tape & Reel
NCV4279B
PACKAGE DIMENSIONS
SO−8
D SUFFIX
CASE 751−07
ISSUE AA
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A AND B DO NOT INCLUDE MOLD
PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER
SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN
EXCESS OF THE D DIMENSION AT MAXIMUM
MATERIAL CONDITION.
6. 751−01 THRU 751−06 ARE OBSOLETE. NEW
STANDAARD IS 751−07
−X−
A
8
5
0.25 (0.010)
S
B
1
M
Y
M
4
K
−Y−
G
C
N
X 45 SEATING
PLANE
−Z−
0.10 (0.004)
H
M
D
0.25 (0.010)
Z Y
M
X
S
J
S
DIM
A
B
C
D
G
H
J
K
M
N
S
MILLIMETERS
MIN
MAX
4.80
5.00
3.80
4.00
1.35
1.75
0.33
0.51
1.27 BSC
0.10
0.25
0.19
0.25
0.40
1.27
0
8
0.25
0.50
5.80
6.20
INCHES
MIN
MAX
0.189
0.197
0.150
0.157
0.053
0.069
0.013
0.020
0.050 BSC
0.004
0.010
0.007
0.010
0.016
0.050
0
8
0.010
0.020
0.228
0.244
SO−14
D SUFFIX
CASE 751A−03
ISSUE F
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
−A−
14
8
−B−
1
P 7 PL
0.25 (0.010)
7
G
M
B
M
F
R X 45 C
−T−
SEATING
PLANE
D 14 PL
0.25 (0.010)
T B
J
M
K
M
S
A
S
http://onsemi.com
11
DIM
A
B
C
D
F
G
J
K
M
P
R
MILLIMETERS
MIN
MAX
8.55
8.75
3.80
4.00
1.35
1.75
0.35
0.49
0.40
1.25
1.27 BSC
0.19
0.25
0.10
0.25
0
7
5.80
6.20
0.25
0.50
INCHES
MIN
MAX
0.337
0.344
0.150
0.157
0.054
0.068
0.014
0.019
0.016
0.049
0.050 BSC
0.008
0.009
0.004
0.009
0
7
0.228
0.244
0.010
0.019
NCV4279B
PACKAGE DIMENSIONS
SO−20L
DW SUFFIX
CASE 751D−05
ISSUE F
A
20
X 45 M
E
h
0.25
H
10X
NOTES:
1. DIMENSIONS ARE IN MILLIMETERS.
2. INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.5M, 1994.
3. DIMENSIONS D AND E DO NOT INCLUDE MOLD
PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE.
5. DIMENSION B DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE PROTRUSION SHALL
BE 0.13 TOTAL IN EXCESS OF B DIMENSION AT
MAXIMUM MATERIAL CONDITION.
11
B
M
D
1
10
20X
B
B
0.25
M
T A
S
B
S
L
A
18X
e
A1
SEATING
PLANE
C
T
DIM
A
A1
B
C
D
E
e
H
h
L
MILLIMETERS
MIN
MAX
2.35
2.65
0.10
0.25
0.35
0.49
0.23
0.32
12.65
12.95
7.40
7.60
1.27 BSC
10.05
10.55
0.25
0.75
0.50
0.90
0
7
SMART REGULATOR is a registered trademark of Semiconductor Components Industries, LLC.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make
changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all
liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be
validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others.
SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death
may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.
PUBLICATION ORDERING INFORMATION
Literature Fulfillment:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
JAPAN: ON Semiconductor, Japan Customer Focus Center
2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051
Phone: 81−3−5773−3850
ON Semiconductor Website: http://onsemi.com
For additional information, please contact your local
Sales Representative.
N. American Technical Support: 800−282−9855 Toll Free USA/Canada
http://onsemi.com
12
NCV4279B/D