ETC CS8126

CS8126
5.0 V, 750 mA Low
Dropout Linear Regulator
with Delayed RESET
The CS8126 is a low dropout, high current 5.0 V linear regulator. It
is an improved replacement for the CS8156. Improvements include
higher accuracy, tighter saturation control, better supply rejection, and
enhanced RESET circuitry. Familiar PNP regulator features such as
reverse battery protection, overvoltage shutdown, thermal shutdown,
and current limit make the CS8126 suitable for use in automotive and
battery operated equipment. Additional on–chip filtering has been
included to enhance rejection of high frequency transients on all
external leads.
An active microprocessor RESET function is included on–chip with
externally programmable delay time. During power–up, or after
detection of any error in the regulated output, the RESET lead will
remain in the low state for the duration of the delay. Types of errors
include short circuit, low input voltage, overvoltage shutdown,
thermal shutdown, or others that cause the output to become
unregulated. This function is independent of the input voltage and will
function correctly with an output voltage as low as 1.0 V. Hysteresis is
included in both the reset and Delay comparators for enhanced noise
immunity. A latching discharge circuit is used to discharge the Delay
capacitor, even when triggered by a relatively short fault condition.
This circuit improves upon the commonly used SCR structure by
providing full capacitor discharge (0.2 V type).
Note: The CS8126 is lead compatible with the LM2927 and
LM2926.
http://onsemi.com
TO–220
FIVE LEAD
T SUFFIX
CASE 314D
1
5
TO–220
FIVE LEAD
TVA SUFFIX
CASE 314K
1
1
TO–220
FIVE LEAD
THA SUFFIX
CASE 314A
Pin 1. VIN
2. VOUT
3. GND
4. Delay
5. RESET
5
TO–220
FIVE LEAD
THE SUFFIX
CASE 314J
1
5
Features
• Low Dropout Voltage (0.6 V at 0.5 A)
• 3.0% Output Accuracy
• Active RESET
• External RESET Delay for Reset
• Protection Circuitry
– Reverse Battery Protection
– +60 V, –50 V Peak Transient Voltage
– Short Circuit Protection
– Internal Thermal Overload Protection
D2PAK
7–PIN
DPS SUFFIX
CASE 936H
1
7
Pin 1. VIN
2. VOUT
3. VOUT(SENSE)
4. GND
5. Delay
6. RESET
7. NC
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 9 of this data sheet.
DEVICE MARKING INFORMATION
See general marking information in the device marking
section on page 9 of this data sheet.
 Semiconductor Components Industries, LLC, 2001
October, 2001 – Rev. 13
1
Publication Order Number:
CS8126/D
CS8126
VIN
Over Voltage
Shutdown
VOUT
Regulated Supply
for Circuit Bias
Pre–Regulator
Bandgap
Reference
Error
Amp
Anti–Saturation
and
Current Limit
–
+
Internally
connected
on 5 Lead
TO–220
VOUT(SENSE)
Charge
Current
Generator
Thermal
Shutdown
Delay
Latching
Discharge
–
Q
S
R
–
+
Reset
Comparator
+
Delay
Comparator
VDischarge
+
–
GND
Figure 1. Block Diagram
http://onsemi.com
2
RESET
CS8126
MAXIMUM RATINGS*
Rating
Value
Unit
Internally Limited
–
–50, 60
V
Internally Limited
–
ESD Susceptibility (Human Body Model)
4.0
kV
Package Thermal Resistance, TO–220 5–Lead:
Junction–to–Case, RθJC
Junction–to–Ambient, RθJA
2.1
50
°C/W
°C/W
2.1
10–50**
°C/W
°C/W
Junction Temperature Range
–40 to +150
°C
Storage Temperature Range
–55 to +150
°C
260 peak
230 peak
°C
°C
Power Dissipation
Peak Transient Voltage (46 V Load Dump)
Output Current
Package Thermal Resistance, D2PAK, 7–Pin:
Junction–to–Case, RθJC
Junction–to–Ambient, RθJA
Lead Temperature Soldering:
Wave Solder (through hole styles only) (Note 1)
Reflow (SMD styles only) (Note 2)
1. 10 second maximum.
2. 60 second maximum above 183°C.
*The maximum package power dissipation must be observed.
**Depending on thermal properties of substrate. RθJA = RθJC + RθCA.
ELECTRICAL CHARACTERISTICS (TA = –40°C to +125°C, TJ = –40°C to +150°C, VIN = 6.0 to 26 V,
IO = 5.0 to 500 mA, RRESET = 4.7 kΩ to VCC, unless otherwise noted.)
Characteristic
Test Conditions
Min
Typ
Max
Unit
–
4.85
5.00
5.15
V
Output Stage (VOUT)
Output Voltage
Dropout Voltage
IOUT1 = 500 mA
–
0.35
0.60
V
Supply Current
IOUT ≤ 10 mA
IOUT ≤ 100 mA
IOUT ≤ 500 mA
–
–
–
2.0
6.0
55
7.0
12
100
mA
mA
mA
Line Regulation
VIN = 6.0 to 26 V, IOUT = 50 mA
–
5.0
50
mV
Load Regulation
IOUT = 50 to 500 mA, VIN = 14 V
–
10
50
mV
Ripple Rejection
f = 120 Hz, VIN = 7.0 to 17 V, IOUT = 250 mA
54
75
–
dB
Current Limit
–
0.75
1.20
–
A
Overvoltage Shutdown
–
32
–
40
V
–
95
–
V
–15
–30
–
V
–
–80
–
V
150
180
210
°C
Maximum Line Transient
VOUT ≤ 5.5 V
Reverse Polarity Input Voltage DC
VOUT ≥ –0.6 V, 10 Ω Load
Reverse Polarity Input Voltage Transient
1.0% Duty Cycle, T < 100 ms, 10 Ω Load
Thermal Shutdown
Note 3
3. Guaranteed By Design
http://onsemi.com
3
CS8126
ELECTRICAL CHARACTERISTICS (continued) (TA = –40°C to +125°C, TJ = –40°C to +150°C, VIN = 6.0 to 26 V,
IO = 5.0 to 500 mA, RRESET = 4.7 kΩ to VCC, unless otherwise noted.)
Characteristic
Test Conditions
Min
Typ
Max
Unit
RESET and Delay Functions
Delay Charge Current
VDelay = 2.0 V
5.0
10
15
µA
RESET Threshold
VOUT Increasing, VRT(ON)
VOUT Decreasing, VRT(OFF)
4.65
4.50
4.90
4.70
VOUT – 0.01
VOUT – 0.15
V
V
RESET Hysteresis
VRH = VRT(ON) – VRT(OFF)
150
200
250
mV
Delay Threshold
Charge, VDC(HI)
Discharge, VDC(LO)
3.25
2.85
3.50
3.10
3.75
3.35
V
V
200
400
800
mV
Delay Hysteresis
–
RESET Output Voltage Low
1.0 V < VOUT < VRTL, 3.0 kΩ to VOUT
–
0.1
0.4
V
RESET Output Leakage Current
VOUT > VRT(ON)
–
0
10
µA
Delay Capacitor Discharge Voltage
Discharge Latched “ON”, VOUT > VRT
–
0.2
0.5
V
Delay Time
CDelay = 0.1 µF*. Note 4
16
32
48
ms
CDelay VDelayThreshold Charge
* Delay Time CDelay 3.2
ICharge
4. Assumes Ideal Capacitor
PACKAGE LEAD DESCRIPTION
PACKAGE LEAD #
TO–220
5 LEAD
D2PAK
7–PIN
LEAD SYMBOL
1
1
VIN
2
2
VOUT
Regulated 5.0 V output.
3
4
GND
Ground connection.
4
5
Delay
Timing capacitor for RESET function.
5
6
RESET
–
3
VOUT(SENSE)
–
7
NC
FUNCTION
Unregulated supply voltage to IC.
CMOS/TTL compatible output lead. RESET goes low after detection of any error in
the regulated output or during power up.
Remote sensing of output voltage.
No Connection.
http://onsemi.com
4
CS8126
TYPICAL PERFORMANCE CHARACTERISTICS
RLOAD = 25 Ω
Room Temp.
120
110
55
50
45
35
ICQ (mA)
ICQ (mA)
40
30
25°C
25
20
15
RLOAD = 6.67
100
90
80
125°C
70
60
RLOAD = 10
50
40
30
20
–40°C
10
5.0
RLOAD = 25
10
0
0
0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
10
RLOAD = NO LOAD
0
1.0
2.0
3.0
4.0
7.0
8.0
Figure 2. ICQ vs. VIN Over Temperature
Figure 3. ICQ vs. VIN Over RLOAD
5.5
5.0
5.0
4.5
4.5
4.0
4.0
3.5
3.5
3.0
125°C
2.5
2.0
–40°C
1.5
10
9.0
10
RLOAD = NO LOAD
RLOAD = 6.67
3.0
2.5
2.0
1.5
1.0
RLOAD = 10
1.0
0.5
9.0
Room Temp.
5.5
VOUT (V)
VOUT (V)
6.0
VIN (V)
RLOAD = 25 Ω
0.5
25°C
0
0
0
100
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
10
0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
VIN (V)
VIN (V)
Figure 4. VOUT vs. VIN Over Temperature
Figure 5. VOUT vs. VIN Over RLOAD
6.0
VIN 6.0–26 V
80
TEMP = –40°C
4.0
40
Load Regulation (mV)
60
Line Regulation (mV)
5.0
VIN (V)
TEMP = 25°C
20
TEMP = 40°C
0
–20
–40
TEMP = 125°C
2.0
0
–2.0
VIN = 14 V
–6.0
TEMP = 125°C
–8.0
–60
–10
–80
–12
–100
TEMP = 25°C
–4.0
–14
0
100
200
300
400
500
600
700
800
0
100
200
300
400
500
600
700
Output Current (mA)
Output Current (mA)
Figure 6. Line Regulation vs. Output
Current Over Temperature
Figure 7. Load Regulation vs. Output
Current Over Temperature
http://onsemi.com
5
800
CS8126
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
900
100
700
600
Quiescent Current (mA)
Dropout Voltage (mV)
25°C
125°C
500
400
300
–40°C
200
100
80
25°C
VIN = 14 V
70
–40°C
60
50
40
30
20
10
0
0
0
100
200
300
400
500
600
700
800
0
100
200
300
600
700
Figure 8. Dropout Voltage vs. Output
Current Over Temperature
Figure 9. Quiescent Current vs. Output
Current Over Temperature
800
103
COUT ==10
COUT
10µF,
mF,ESR = 1
ESR
& 0.1=µF,
1 &ESR
0.1 =
mF,
0 ESR = 0
70
102
101
ESR (Ω)
60
50
40
COUT = 10 µF, ESR = 1.0 Ω
30
COUT = 47/68 µF
100
Stable Region
10–1
COUT = 47 µF
10–2
20
COUT = 10 µF, ESR = 10 Ω
101
102
103
104
105
106
COUT = 68 µF
10–3
10
100
500
Output Current (mA)
80
0
400
Output Current (mA)
90
Rejection (dB)
125°C
90
800
107
10–4
108
100
101
102
Freq. (Hz)
Output Current (mA)
Figure 10. Ripple Rejection
Figure 11. Output Capacitor ESR
103
RESET CIRCUIT WAVEFORM
VOUT
VRT(ON)
VRT(OFF)
(1) = No Delay Capacitor
(2) = With Delay Capacitor
(3) = Max:RESET Voltage (1.0 V)
VRH
(1)
RESET
(2)
(3)
VRL
tDelay
Delay
VDC(HI)
VDC(LO)
VDH
VDIS
(2)
Figure 12. RESET Circuit Waveform
http://onsemi.com
6
CS8126
CIRCUIT DESCRIPTION
The CS8126 RESET function, has hysteresis on both the
Reset and Delay comparators, a latching Delay capacitor
discharge circuit, and operates down to 1.0 V.
The RESET circuit output is an open collector type with
ON and OFF parameters as specified. The RESET output
NPN transistor is controlled by the two circuits described
(see Block Diagram).
voltage is above VRT(ON). Otherwise, the Delay lead sinks
current to ground (used to discharge the delay capacitor).
The discharge current is latched ON when the output voltage
falls below VRT(OFF). The Delay capacitor is fully
discharged anytime the output voltage falls out of
regulation, even for a short period of time. This feature
ensures a controlled RESET pulse is generated following
detection of an error condition. The circuit allows the
RESET output transistor to go to the OFF (open) state only
when the voltage on the Delay lead is higher than VDC(H1).
The Delay time for the RESET function is calculated from
the formula:
Low Voltage Inhibit Circuit
This circuit monitors output voltage, and when the output
voltage falls below VRT(OFF), causes the RESET output
transistor to be in the ON (saturation) state. When the output
voltage rises above VRT(ON), this circuit permits the RESET
output transistor to go into the OFF state if allowed by the
RESET Delay circuit.
Delay time CDelay VDelayThreshold
ICharge
Delay time CDelay 3.2 105
RESET Delay Circuit
If CDelay = 0.1 µF, Delay time (ms) = 32 ms ± 50%: i.e.
16 ms to 48 ms. The tolerance of the capacitor must be taken
into account to calculate the total variation in the delay time.
This circuit provides a programmable (by external
capacitor) delay on the RESET output lead. The Delay lead
provides source current to the external delay capacitor only
when the “Low Voltage Inhibit” circuit indicates that output
VOUT
VIN
C1 *
100 nF
RRST
4.7 kΩ
CS8126
RESET
Delay
Delay
0.1 µF
C2**
10 µF to 100 µF
GND
* C1 is required if the regulator is far from the power source filter.
** C2 is required for stability.
Figure 13. Application Diagram
APPLICATION NOTES
Stability Considerations
temperatures (–25°C to –40°C), both the value and ESR of
the capacitor will vary considerably. The capacitor
manufacturers data sheet usually provides this information.
The value for the output capacitor C2 shown in the test and
applications circuit should work for most applications,
however it is not necessarily the optimized solution.
To determine an acceptable value for C2 for a particular
application, start with a tantalum capacitor of the
recommended value and work towards a less expensive
alternative part.
The output or compensation capacitor helps determine
three main characteristics of a linear regulator: start–up
delay, load transient response and loop stability.
The capacitor value and type should be based on cost,
availability, size and temperature constraints. A tantalum or
aluminum electrolytic capacitor is best, since a film or
ceramic capacitor with almost zero ESR, can cause
instability. The aluminum electrolytic capacitor is the least
expensive solution, but, if the circuit operates at low
http://onsemi.com
7
CS8126
VIN(max) is the maximum input voltage,
VOUT(min) is the minimum output voltage,
IOUT(max) is the maximum output current, for the
application, and
IQ is the quiescent current the regulator consumes at
IOUT(max).
Once the value of PD(max) is known, the maximum
permissible value of RΘJA can be calculated:
Step 1: Place the completed circuit with a tantalum
capacitor of the recommended value in an environmental
chamber at the lowest specified operating temperature and
monitor the outputs with an oscilloscope. A decade box
connected in series with the capacitor will simulate the
higher ESR of an aluminum capacitor. Leave the decade box
outside the chamber, the small resistance added by the
longer leads is negligible.
Step 2: With the input voltage at its maximum value,
increase the load current slowly from zero to full load while
observing the output for any oscillations. If no oscillations
are observed, the capacitor is large enough to ensure a stable
design under steady state conditions.
Step 3: Increase the ESR of the capacitor from zero using the
decade box and vary the load current until oscillations
appear. Record the values of load current and ESR that cause
the greatest oscillation. This represents the worst case load
conditions for the regulator at low temperature.
Step 4: Maintain the worst case load conditions set in step
3 and vary the input voltage until the oscillations increase.
This point represents the worst case input voltage
conditions.
Step 5: If the capacitor is adequate, repeat steps 3 and 4 with
the next smaller valued capacitor. A smaller capacitor will
usually cost less and occupy less board space. If the output
oscillates within the range of expected operating conditions,
repeat steps 3 and 4 with the next larger standard capacitor
value.
Step 6: Test the load transient response by switching in
various loads at several frequencies to simulate its real
working environment. Vary the ESR to reduce ringing.
Step 7: Raise the temperature to the highest specified
operating temperature. Vary the load current as instructed in
step 5 to test for any oscillations.
RJA (2)
The value of RΘJA can then be compared with those in the
package section of the data sheet. Those packages with
RΘJA’s less than the calculated value in equation 2 will keep
the die temperature below 150°C.
In some cases, none of the packages will be sufficient to
dissipate the heat generated by the IC, and an external
heatsink will be required.
IIN
VIN
IOUT
SMART
REGULATOR
VOUT
Control
Features
IQ
Figure 14. Single Output Regulator With Key
Performance Parameters Labeled
Heat Sinks
A heat sink effectively increases the surface area of the
package to improve the flow of heat away from the IC and
into the surrounding air.
Each material in the heat flow path between the IC and the
outside environment will have a thermal resistance. Like
series electrical resistances, these resistances are summed to
determine the value of RΘJA.
Once the minimum capacitor value with the maximum
ESR is found, a safety factor should be added to allow for the
tolerance of the capacitor and any variations in regulator
performance. Most good quality aluminum electrolytic
capacitors have a tolerance of ± 20% so the minimum value
found should be increased by at least 50% to allow for this
tolerance plus the variation which will occur at low
temperatures. The ESR of the capacitor should be less than
50% of the maximum allowable ESR found in step 3 above.
RJA RJC RCS RSA
(3)
where:
RΘJC = the junction–to–case thermal resistance,
RΘCS = the case–to–heatsink thermal resistance, and
RΘSA = the heatsink–to–ambient thermal resistance.
RΘJC appears in the package section of the data sheet. Like
RΘJA, it is a function of package type. RΘCS and RΘSA are
functions of the package type, heatsink and the interface
between them. These values appear in heat sink data sheets
of heat sink manufacturers.
Calculating Power Dissipation in a Single Output
Linear Regulator
The maximum power dissipation for a single output
regulator (Figure 14) is:
PD(max) VIN(max) VOUT(min)IOUT(max) VIN(max)IQ
150°C TA
PD
(1)
where:
http://onsemi.com
8
CS8126
ORDERING INFORMATION
Device
Description
Shipping
TO–220 FIVE LEAD STRAIGHT
50 Units/Rail
CS8126–1YTVA5
TO–220 FIVE LEAD VERTICAL
50 Units/Rail
CS8126–1YTHA5
TO–220 FIVE LEAD HORIZONTAL
50 Units/Rail
CS8126–1YTHE5
TO–220 FIVE LEAD SURFACE MOUNT
50 Units/Rail
CS8126–1YTHER5
TO–220 FIVE LEAD SURFACE MOUNT
750 Tape & Reel
CS8126–1YDPS7
D2PAK, 7–PIN
50 Units/Rail
CS8126–1YDPSR7
D2PAK,
CS8126–1YT5
7–PIN
750 Tape & Reel
MARKING DIAGRAMS
TO–220
FIVE LEAD
T SUFFIX
CASE 314D
TO–220
FIVE LEAD
TVA SUFFIX
CASE 314K
TO–220
FIVE LEAD
THA SUFFIX
CASE 314A
TO–220
FIVE LEAD
THE SUFFIX
CASE 314J
D2PAK
7–PIN
DPS SUFFIX
CASE 936H
CS8126
AWLYWW
CS8126
AWLYWW
CS8126
AWLYWW
CS8126
AWLYWW
CS8126
AWLYWW
1
1
1
1
A
WL, L
YY, Y
WW, W
1
= Assembly Location
= Wafer Lot
= Year
= Work Week
http://onsemi.com
9
CS8126
PACKAGE DIMENSIONS
TO–220
FIVE LEAD
T SUFFIX
CASE 314D–04
ISSUE E
–T–
–Q–
SEATING
PLANE
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION D DOES NOT INCLUDE
INTERCONNECT BAR (DAMBAR) PROTRUSION.
DIMENSION D INCLUDING PROTRUSION SHALL
NOT EXCEED 10.92 (0.043) MAXIMUM.
C
B
E
A
U
L
K
J
H
G
D
DIM
A
B
C
D
E
G
H
J
K
L
Q
U
1234 5
5 PL
0.356 (0.014)
M
T Q
M
INCHES
MIN
MAX
0.572
0.613
0.390
0.415
0.170
0.180
0.025
0.038
0.048
0.055
0.067 BSC
0.087
0.112
0.015
0.025
0.990
1.045
0.320
0.365
0.140
0.153
0.105
0.117
MILLIMETERS
MIN
MAX
14.529 15.570
9.906 10.541
4.318
4.572
0.635
0.965
1.219
1.397
1.702 BSC
2.210
2.845
0.381
0.635
25.146 26.543
8.128
9.271
3.556
3.886
2.667
2.972
TO–220
FIVE LEAD
TVA SUFFIX
CASE 314K–01
ISSUE O
–T–
SEATING
PLANE
C
B
–Q–
E
W
A
U
F
L
1
2
3
4
K
5
M
D
0.356 (0.014)
M
J
5 PL
T Q
M
G
S
R
http://onsemi.com
10
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION D DOES NOT INCLUDE
INTERCONNECT BAR (DAMBAR) PROTRUSION.
DIMENSION D INCLUDING PROTRUSION SHALL
NOT EXCEED 10.92 (0.043) MAXIMUM.
DIM
A
B
C
D
E
F
G
J
K
L
M
Q
R
S
U
W
INCHES
MIN
MAX
0.560
0.590
0.385
0.415
0.160
0.190
0.027
0.037
0.045
0.055
0.530
0.545
0.067 BSC
0.014
0.022
0.785
0.800
0.321
0.337
0.063
0.078
0.146
0.156
0.271
0.321
0.146
0.196
0.460
0.475
5°
MILLIMETERS
MIN
MAX
14.22
14.99
9.78
10.54
4.06
4.83
0.69
0.94
1.14
1.40
13.46
13.84
1.70 BSC
0.36
0.56
19.94
20.32
8.15
8.56
1.60
1.98
3.71
3.96
6.88
8.15
3.71
4.98
11.68
12.07
5°
CS8126
TO–220
FIVE LEAD
THA SUFFIX
CASE 314A–03
ISSUE E
–T–
B
–P–
Q
C
E
OPTIONAL
CHAMFER
A
U
F
L
DIM
A
B
C
D
E
F
G
J
K
L
Q
S
U
K
G
5X
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION D DOES NOT INCLUDE
INTERCONNECT BAR (DAMBAR) PROTRUSION.
DIMENSION D INCLUDING PROTRUSION SHALL
NOT EXCEED 0.043 (1.092) MAXIMUM.
SEATING
PLANE
5X
J
S
D
0.014 (0.356)
M
T P
M
INCHES
MIN
MAX
0.572
0.613
0.390
0.415
0.170
0.180
0.025
0.038
0.048
0.055
0.570
0.585
0.067 BSC
0.015
0.025
0.730
0.745
0.320
0.365
0.140
0.153
0.210
0.260
0.468
0.505
MILLIMETERS
MIN
MAX
14.529 15.570
9.906 10.541
4.318
4.572
0.635
0.965
1.219
1.397
14.478 14.859
1.702 BSC
0.381
0.635
18.542 18.923
8.128
9.271
3.556
3.886
5.334
6.604
11.888 12.827
TO–220
FIVE LEAD
THE SUFFIX
CASE 314J–01
ISSUE O
–T–
SEATING
PLANE
C
B
–Q–
E
W
A
U
F
L
1
D
0.356 (0.014)
M
2
3
4
5
5 PL
T Q
K
J
M
G
–M–
S
0.102 (0.004)
–N–
http://onsemi.com
11
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION D DOES NOT INCLUDE
INTERCONNECT BAR (DAMBAR) PROTRUSION.
DIMENSION D INCLUDING PROTRUSION SHALL
NOT EXCEED 10.92 (0.043) MAXIMUM.
4. DIMENSIONS EXCLUSIVE OF MOLD FLASH
AND METAL BURRS.
5. FOOTPAD LENGTH MEASURED FROM LEAD
TIP WITH REFERENCE TO DATUM -M-.
6. COPLANARITY 0.004" MAX. REFERENCE TO
DATUM -N- STANDOFF HEIGHT 0.00 - 0.010".
DIM
A
B
C
D
E
F
G
J
K
L
Q
S
U
W
INCHES
MIN
MAX
0.568
0.583
0.395
0.405
0.170
0.180
0.028
0.036
0.045
0.055
0.543
0.558
0.067 BSC
0.014
0.022
0.073
0.088
0.324
0.339
0.146
0.156
0.000
0.010
0.460
0.475
5°
MILLIMETERS
MIN
MAX
14.43
14.81
10.03
10.29
4.32
4.57
0.71
0.91
1.14
1.40
13.79
14.17
1.70 BSC
0.36
0.56
1.85
2.24
8.23
8.61
3.71
3.96
0.00
0.25
11.68
12.07
5°
CS8126
D2PAK
7–PIN
DPS SUFFIX
CASE 936H–01
ISSUE O
–T– SEATING
PLANE
B
M
U
C
E
8
NOTES:
1. DIMENSIONS AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. TAB CONTOUR OPTIONAL WITHIN DIMENSIONS
B AND M.
4. DIMENSIONS A AND B DO NOT INCLUDE MOLD
FLASH OR GATE PROTRUSIONS. MOLD FLASH
AND GATE PROTRUSIONS NOT TO EXCEED
0.025 (0.635) MAX.
V
DIM
A
B
C
D
E
F
G
H
J
K
M
N
U
V
A
1 2 34 5 6 7
K
F
G
D
H
7 PL
0.13 (0.005)
M
T B
J
M
INCHES
MIN
MAX
0.326
0.336
0.396
0.406
0.170
0.180
0.026
0.036
0.045
0.055
0.058
0.078
0.050 BSC
0.100
0.110
0.018
0.025
0.204
0.214
0.055
0.066
0.000
0.004
0.256 REF
0.305 REF
MILLIMETERS
MIN
MAX
8.28
8.53
10.05
10.31
4.31
4.57
0.66
0.91
1.14
1.40
1.41
1.98
1.27 BSC
2.54
2.79
0.46
0.64
5.18
5.44
1.40
1.68
0.00
0.10
6.50 REF
7.75 REF
N
SMART REGULATOR is a registered trademark of Semiconductor Components Industries, LLC (SCILLC).
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes
without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular
purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability,
including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be
validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others.
SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or
death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold
SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable
attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.
PUBLICATION ORDERING INFORMATION
Literature Fulfillment:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada
Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada
Email: [email protected]
JAPAN: ON Semiconductor, Japan Customer Focus Center
4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–0031
Phone: 81–3–5740–2700
Email: [email protected]
ON Semiconductor Website: http://onsemi.com
For additional information, please contact your local
Sales Representative.
N. American Technical Support: 800–282–9855 Toll Free USA/Canada
http://onsemi.com
12
CS8126/D