SEMICONDUCTOR TECHNICAL DATA The MC10ELT/100ELT22 is a dual TTL to differential PECL translator. Because PECL (Positive ECL) levels are used only +5V and ground are required. The small outline 8-lead SOIC package and the low skew, dual gate design of the ELT22 makes it ideal for applications which require the translation of a clock and a data signal. Because the mature MOSAIC 1.5 process is used, low cost can be added to the list of features. The ELT22 is available in both ECL standards: the 10ELT is compatible with positive MECL 10H logic levels while the 100ELT is compatible with positive ECL 100K logic levels. • • • • • • 1.5ns Typical Propagation Delay 8 1 <300ps Typical Output to Output Skew Differential PECL Outputs D SUFFIX PLASTIC SOIC PACKAGE CASE 751-05 Small Outline SOIC Package PNP TTL Inputs for Minimal Loading Flow Through Pinouts LOGIC DIAGRAM AND PINOUT ASSIGNMENT Q0 1 8 VCC Q0 7 D0 2 PECL Q1 Q1 PIN DESCRIPTION TTL 3 6 4 5 D1 PIN FUNCTION GND Qn Dn VCC GND Diff PECL Outputs TTL Inputs +5.0V Supply Ground 7/96 Motorola, Inc. 1996 3–1 REV 3 MC10ELT22 MC100ELT22 MAXIMUM RATINGS* Symbol Parameter VCC DC Supply Voltage (Referenced to GND) VIN Input Voltage IOUT Current Applied to Output in Low Output State TA Operating Temperature Range (In Free-Air) TSTG Storage Temperature Range Value Unit 7.0 V 0 to VCC V 50 100 mA –40 to 85 °C –55 to +150 °C Continuous Surge * Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. TTL INPUT DC CHARACTERISTICS (VCC = 4.75V to 5.25V; TA = –40°C to 85°C) Symbol Characteristic Min Typ Max Unit Condition IIH Input HIGH Current 20 µA VIN = 2.7V IIHH Input HIGH Current 100 µA VIN = 7.0V IIL Input LOW Current –0.6 mA VIN = 0.5V –1.2 V VIK VIH Input HIGH Voltage VIL Input LOW Voltage 2.0 IIN = –18mA V 0.8 V PECL OUTPUT DC CHARACTERISTICS (VCC = 4.75V to 5.25V; TA = –40°C to 85°C) –40°C Symbol 0°C 25°C 85°C Characteristic Min Max Min Max Min Typ Max Min Max Unit Condition VOH Output HIGH 10ELT1 Voltage 100ELT1 3.920 3.915 4.11 4.12 3.980 3.975 4.16 4.12 4.020 3.975 4.10 4.05 4.19 4.12 4.090 3.975 4.28 4.12 V VCC = 5.0V VOL Output LOW 10ELT1 Voltage 100ELT1 3.05 3.17 3.350 3.445 3.05 3.19 3.37 3.38 3.05 3.19 3.25 3.30 3.37 3.38 3.05 3.19 3.40 3.35 V VCC = 5.0V 22 mA ICC Power Supply Current 1. Levels will vary 1:1 with VCC. 22 22 22 AC CHARACTERISTICS (VCC = 4.75V to 5.25V; TA = –40°C to 85°C) –40°C Symbol Characteristic 0°C 25°C 85°C Min Max Min Max Min Typ Max Min Max Unit tPLH Propagation Delay1 0.6 1.2 0.65 1.45 0.9 1.2 1.5 0.6 1.35 ns tPHL Propagation Delay1 0.4 1.0 0.45 1.05 0.5 0.8 1.1 0.7 1.30 ns tr/tf Output Rise/Fall Time 0.4 1.6 0.4 1.6 0.4 1.6 0.4 1.6 ns fMAX Maximum Input Frequency 100 100 100 100 Condition 20–80% MHz 1. Specifications for standard TTL input signal. MOTOROLA 3–2 ECLinPS and ECLinPS Lite DL140 — Rev 3 MC10ELT22 MC100ELT22 OUTLINE DIMENSIONS D SUFFIX PLASTIC SOIC PACKAGE CASE 751–05 ISSUE P –A– M 1 4 R 0.25 (0.010) 4X –B– X 45 _ B M 5 P 8 NOTES: 1. DIMENSIONS A AND B ARE DATUMS AND T IS A DATUM SURFACE. 2. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 3. DIMENSIONS ARE IN MILLIMETER. 4. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 5. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE. 6. DIMENSION D DOES NOT INCLUDE MOLD PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. J M_ C F G –T– K SEATING PLANE 8X D 0.25 (0.010) M T B S A S DIM A B C D F G J K M P R MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.18 0.25 0.10 0.25 0_ 7_ 5.80 6.20 0.25 0.50 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454 JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315 MFAX: [email protected] – TOUCHTONE 602–244–6609 INTERNET: http://Design–NET.com ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298 ◊ ECLinPS and ECLinPS Lite DL140 — Rev 3 3–3 *MC10ELT22/D* MC10ELT22/D MOTOROLA