SEMICONDUCTOR TECHNICAL DATA The MC10EL/100EL05 is a 2-input differential AND/NAND gate. The device is functionally equivalent to the E404 device with higher performance capabilities. With propagation delays and output transition times significantly faster than the E404 the EL05 is ideally suited for those applications which require the ultimate in AC performance. Because a negative 2-input NAND is equivalent to a 2-input OR function, the differential inputs and outputs of the device allows the EL05 to also be used as a 2-input differential OR/NOR gate. The differential inputs employ clamp circuitry so that under open input conditions (pulled down to VEE) the input to the AND gate will be HIGH. In this way, if one set of inputs is open, the gate will remain active to the other input. 8 1 • • • • 275ps Propagation Delay D SUFFIX PLASTIC SOIC PACKAGE CASE 751-05 High Bandwidth Output Transitions 75kΩ Internal Input Pulldown Resistors >1000V ESD Protection LOGIC DIAGRAM AND PINOUT ASSIGNMENT D0 1 8 VCC D0 2 7 Q D1 3 6 Q D1 4 PIN DESCRIPTION PIN FUNCTION D0, D1 Q Data Inputs Data Outputs 5 VEE 12/93 Motorola, Inc. 1996 3–1 REV 2 MC10EL05 MC100EL05 DC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = GND) –40°C Symbol IEE VEE IIH Characteristic Min Power Supply Current 10EL 100EL Power Supply Voltage 10EL 100EL –4.75 –4.20 0°C Typ Max 18 18 22 22 –5.2 –4.5 –5.5 –5.5 Input HIGH Current Min –4.75 –4.20 25°C Typ Max 18 18 22 22 –5.2 –4.5 –5.5 –5.5 150 Min –4.75 –4.20 85°C Typ Max 18 18 22 22 –5.2 –4.5 –5.5 –5.5 150 Min –4.75 –4.20 Typ Max Unit 18 21 22 25 mA –5.2 –4.5 –5.5 –5.5 V 150 µA 150 AC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = GND) –40°C Symbol Characteristic 0°C 25°C 85°C Min Typ Max Min Typ Max Min Typ Max Min Typ Max Unit 260 440 185 275 390 185 275 390 215 305 420 ps tPLH tPHL Propagation Delay to Output 135 VPP Minimum Input Swing1 150 VCMR Common Mode Range2 –0.4 tr tf Output Rise/Fall Times Q (20% – 80%) 100 150 225 See2 –0.4 350 100 150 225 See2 –0.4 350 100 150 225 See2 –0.4 350 100 mV 225 See2 V 350 ps 1. Minimum input swing for which AC parameters are guaranteed. The device has a DC gain of ≈40. 2. The CMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPPmin and 1V. The lower end of the CMR range is dependent on VEE and is equal to VEE + 3.0V. MOTOROLA 3–2 ECLinPS and ECLinPS Lite DL140 — Rev 3 MC10EL05 MC100EL05 OUTLINE DIMENSIONS D SUFFIX PLASTIC SOIC PACKAGE CASE 751–05 ISSUE P –A– M 1 4 R 0.25 (0.010) 4X –B– X 45 _ B M 5 P 8 NOTES: 1. DIMENSIONS A AND B ARE DATUMS AND T IS A DATUM SURFACE. 2. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 3. DIMENSIONS ARE IN MILLIMETER. 4. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 5. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE. 6. DIMENSION D DOES NOT INCLUDE MOLD PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. J M_ C F G –T– K SEATING PLANE 8X D 0.25 (0.010) M T B S A S DIM A B C D F G J K M P R MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.18 0.25 0.10 0.25 0_ 7_ 5.80 6.20 0.25 0.50 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454 JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315 MFAX: [email protected] – TOUCHTONE 602–244–6609 INTERNET: http://Design–NET.com ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298 ◊ ECLinPS and ECLinPS Lite DL140 — Rev 3 3–3 *MC10EL05/D* MC10EL05/D MOTOROLA