MOTOROLA SEMICONDUCTOR TECHNICAL DATA Differential Receiver MC100LVEL16 The MC100LVEL16 is a differential receiver. The device is functionally equivalent to the EL16 device, operating from a low voltage supply. The LVEL16 exhibits a wider CMR range than its EL16 counterpart. With output transition times and propagation delays comparable to the EL16 the LVEL16 is ideally suited for interfacing with high frequency sources at 3.3V supplies. The LVEL16 provides a VBB output for either single-ended use or as a DC bias for AC coupling to the device. The VBB pin should be used only as a bias for the LVEL16 as its current sink/source capability is limited. Whenever used, the VBB pin should be bypassed to ground via a 0.01µf capacitor. Under open input conditions, the Q input will be pulled down to Vee and the Q input will be biased to VCC/2. This condition will force the Q output low. • • • • 8 1 D SUFFIX PLASTIC SOIC PACKAGE CASE 751-05 300ps Propagation Delay High Bandwidth Output Transitions 75kΩ Internal Input Pulldown Resistors >2000V ESD Protection LOGIC DIAGRAM AND PINOUT ASSIGNMENT NC 1 8 VCC D 2 7 Q D 3 6 Q VBB 4 5 PIN DESCRIPTION PIN FUNCTION D Q VBB Data Inputs Data Outputs Ref. Voltage Output VEE 5/96 Motorola, Inc. 1996 4–1 REV 0 MC100LVEL16 DC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = GND) –40°C Symbol Characteristic Min IEE Power Supply Current VBB Output Reference Voltage –1.38 VEE Power Supply Voltage –3.0 IIH Input HIGH Current IIL Input LOW Current 0°C Typ Max 17 23 –3.3 Min –1.26 –1.38 –3.8 –3.0 25°C Typ Max 17 23 –3.3 –1.26 –1.38 –3.8 –3.0 150 D D 0.5 –600 Min Typ Max 17 23 –3.3 150 0.5 –600 85°C Min –1.26 –1.38 –3.8 –3.0 Typ Max Unit 18 24 mA –1.26 V –3.8 V 150 µA –3.3 150 0.5 –600 µA 0.5 –600 AC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = GND) –40°C Symbol 0°C 25°C 85°C Characteristic Min Typ Max Min Typ Max Min Typ Max Min Typ Max tPLH tPHL Propagation Delay to Output (Diff) (SE) 150 100 275 275 400 450 215 165 290 290 365 415 225 175 300 300 375 425 240 190 315 315 390 440 tSKEW Duty Cycle Skew1 (Diff) 5 30 5 20 5 20 5 20 VPP Minimum Input Swing2 150 VCMR Common Mode Range3 VPP < 500mV VPP ≥ 500mV –2.0 –1.8 Unit ps 150 150 150 ps mV V –0.4 –0.4 –2.1 –1.9 –0.4 –0.4 –2.1 –1.9 –0.4 –0.4 –2.1 –1.9 –0.4 –0.4 tr Output Rise/Fall Times Q 120 220 320 120 220 320 120 220 320 120 220 320 ps tf (20% – 80%) 1. Duty cycle skew is the difference between a TPLH and TPHL propagation delay through a device. 2. Minimum input swing for which AC parameters guaranteed. The device has a DC gain of ≈40. 3. The CMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPPmin and 1V. The lower end of the CMR range varies 1:1 with VEE. The numbers in the spec table assume a nominal VEE = –3.3V. Note for PECL operation, the VCMR(min) will be fixed at 3.3V – |VCMR(min)|. MOTOROLA 4–2 ECLinPS and ECLinPS Lite DL140 — Rev 3 MC100LVEL16 OUTLINE DIMENSIONS D SUFFIX PLASTIC SOIC PACKAGE CASE 751–05 ISSUE M NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. –A– 8 5 –B– 1 4X P 0.25 (0.010) 4 M B R C –T– 8X K D 0.25 (0.010) M T B SEATING PLANE S M A X 45 _ M_ F J S DIM A B C D F G J K M P R MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.18 0.25 0.10 0.25 0_ 7_ 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.189 0.196 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.007 0.009 0.004 0.009 0_ 7_ 0.229 0.244 0.010 0.019 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454 JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315 MFAX: [email protected] – TOUCHTONE 602–244–6609 INTERNET: http://Design–NET.com ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298 ◊ ECLinPS and ECLinPS Lite DL140 — Rev 3 4–3 *MC100LVEL16/D* MC100LVEL16/D MOTOROLA