ONSEMI NB4N840M

NB4N840M
3.3V 3.2Gb/s Dual
Differential Clock/Data 2 x 2
Crosspoint Switch with
CML Output and Internal
Termination
http://onsemi.com
MARKING
DIAGRAM
Description
The NB4N840M is a high−bandwidth fully differential dual
2 x 2 crosspoint switch with CML inputs/outputs that is suitable for
applications such as SDH/SONET, DWDM, Gigabit Ethernet and
high speed switching. Fully differential design techniques are used to
minimize jitter accumulation, crosstalk, and signal skew, which make
this device ideal for loop−through and protection channel switching
applications.
Internally terminated differential CML inputs accept AC−coupled
LVPECL (Positive ECL) or direct coupled CML signals. By providing
internal 50 W input and output termination resistor, the need for
external components is eliminated and interface reflections are
minimized. Differential 16 mA CML outputs provide matching
internal 50 W terminations, and 400 mV output swings when
externally terminated, 50 W to VCC.
Single−ended LVCMOS/LVTTL SEL inputs control the routing of
the signals through the crosspoint switch which makes this device
configurable as 1:2 fan−out, repeater or 2 x 2 crosspoint switch. The
device is housed in a low profile 5 x 5 mm 32−pin QFN package.
•
Plug−in compatible to the MAX3840 and SY55859L
Maximum Input Clock Frequency 2.7 GHz
Maximum Input Data Frequency 3.2 Gb/s
225 ps Typical Propagation Delay
80 ps Typical Rise and Fall Times
7 ps Channel to Channel Skew
430 mW Power Consumption
< 0.5 ps RMS Jitter
7 ps Peak−to−Peak Data Dependent Jitter
Power Saving Feature with Disabled Outputs
Operating Range: VCC = 3.0 V to 3.6 V with VEE = 0 V
CML Output Level (400 mV Peak−to−Peak Output), Differential
Output
These are Pb−Free Devices
© Semiconductor Components Industries, LLC, 2007
March, 2007 − Rev. 3
1
NB4N
840M
ALYWG
32
1
QFN32
MN SUFFIX
CASE 488AM
A
WL
YY
WW
G
DA0
DA0
CML
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
QA0
0
CML
1
QA0
ENA0
SELA0
0
DA1
DA1
CML
1
QA1
CML
QA1
ENA1
SELA1
DB0
DB0
Features
•
•
•
•
•
•
•
•
•
•
•
•
1
CML
0
QB0
CML
1
QB0
ENB0
SELB0
QB1
0
DB1
DB1
CML
1
CML
QB1
ENB1
SELB1
Figure 1. Functional Block Diagram
ORDERING INFORMATION
See detailed ordering and shipping information on page 8 of
this data sheet.
Publication Order Number:
NB4N840M/D
NB4N840M
Table 1. TRUTH TABLE
L
H
H
H
DA0/DB0
DA1/DB1
Quad Repeater
H
L
H
H
DA1/DB1
DA0/DB0
Crosspoint Switch
H
H
H
H
DA1/DB1
DA1/DB1
1:2 Fanout
X
X
L
L
Disable/Power Down
Disable/Power Down
SELA1
1:2 Fanout
DA0
DA0/DB0
DA0
QA1/QB1
DA0/DB0
SELA0
QA0/QB0
H
ENA0
ENB0/ENB1
H
DA1
ENA0/ENA1
L
DA1
SELA1/SELB1
L
ENA1
SELA0/SELB0
32
31
30
29
28
27
26
25
ENB1
1
24
GND
DB1
2
23
VCC
DB1
3
22
QA0
ENB0
4
21
QA0
NB4N840M
6
19
QA1
DB0
7
18
QA1
SELB1
8
17
VCC
11
12
13
14
15
Figure 2. Pin Configuration (Top View)
http://onsemi.com
2
16
VCC
10
VCC
GND
9
QB1
DB0
QB1
VCC
VCC
20
QB0
5
QB0
SELB0
Function
No output (@ VCC)
NB4N840M
Table 2. PIN DESCRIPTION
Pin
Name
I/O
1
ENB1
LVTTL
Description
2
DB1
CML Input
Channel B1 Positive Signal Input
3
DB1
CML Input
Channel B1 Negative Signal Input
4
ENB0
LVTTL
Channel B0 Output Enable. LVTTL low input powers down B0 output stage.
5
SELB0
LVTTL
Channel B0 Output Select. See Table 1.
6
DB0
CML Input
Channel B0 Positive Signal Input
7
DB0
CML Input
Channel B0 Negative Signal Input
8
SELB1
LVTTL
9,24
GND
−
Supply Ground. All GND pins must be externally connected to power supply to guarantee
proper operation.
10, 13, 16,
17, 20, 23
VCC
−
Positive Supply. All VCC pins must be externally connected to power supply to guarantee
proper operation.
11
QB0
CML Output
Channel B0 Negative Output.
12
QB0
CML Output
Channel B0 Positive Output.
14
QB1
CML Output
Channel B1 Negative Output.
15
QB1
CML Output
Channel B1 Positive Output.
18
QA1
CML Output
Channel A1 Negative Output.
19
QA1
CML Output
Channel A1 Positive Output.
21
QA0
CML Output
Channel A0 Negative Output.
22
QA0
CML Output
Channel A0 Positive Output.
25
SELA1
LVTTL
26
DA0
CML Input
Channel A0 Positive Signal Input.
27
DA0
CML Input
Channel A0 Negative Signal Input.
28
SELA0
LVTTL
Channel A0 Output Select, LVTTL Input. See Table 1.
29
ENA0
LVTTL
Channel A0 Output Enable. LVTTL low input powers down A0 output stage.
30
DA1
CML Input
Channel A1 Positive Signal Input.
31
DA1
CML Input
Channel A1 Negative Signal Input.
32
ENA1
LVTTL
−
EP
GND
Channel B1 Output Enable. LVTTL low input powers down B1 output stage.
Channel B1 Output Select. See Table 1.
Channel A1 Output Select, LVTTL Input. See Table 1.
Channel A1 Output Enable. LVTTL low input powers down A1 output stage.
Exposed Pad. The thermally exposed pad (EP) on package bottom (see case drawing)
must be attached to a heat−sinking conduit. The exposed pad must be soldered to the
circuit board GND for proper electrical and thermal operation.
http://onsemi.com
3
NB4N840M
Table 3. ATTRIBUTES
Characteristics
ESD Protection
Value
Human Body Model
Machine Model
Moisture Sensitivity (Note 1)
> 2000 V
> 110 V
QFN−32
Flammability Rating
Level 1
Oxygen Index: 28 to 34
UL 94 V−0 @ 0.125 in
Transistor Count
380
Meets or exceeds JEDEC Spec EIA/JESD78 IC Latchup Test
1. For additional information, refer to Application Note AND8003/D.
Table 4. MAXIMUM RATINGS
Symbol
Parameter
Condition 1
Rating
Unit
3.8
V
3.8
V
3.8
V
Static
Surge
45
80
mA
mA
Output Current
Continuous
Surge
25
80
mA
mA
TA
Operating Temperature Range
QFN−32
−40 to +85
°C
Tstg
Storage Temperature Range
−65 to +150
°C
qJA
Thermal Resistance (Junction−to−Ambient)
(Note 2)
0 lfpm
500 lfpm
QFN−32
QFN−32
31
27
°C/W
°C/W
qJC
Thermal Resistance (Junction−to−Case)
2S2P (Note 3)
QFN−32
12
°C/W
Tsol
Wave Solder
<3 sec @ 260 C
260
°C
VCC
Positive Power Supply
GND = 0 V
VI
Positive Input
GND = 0 V
VINPP
Differential Input Voltage
IIN
Input Current Through Internal 50 W Resistor
IOUT
Condition 2
GND = VI = VCC
|D − D|
Pb−Free
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
2. JEDEC standard 51−6, multilayer board − 2S2P (2 signal, 2 power).
3. JEDEC standard multilayer board − 2S2P (2 signal, 2 power) with 8 filled thermal vias under exposed pad.
http://onsemi.com
4
NB4N840M
Table 5. DC CHARACTERISTICS, CLOCK INPUTS, CML OUTPUTS VCC = 3.0 V to 3.6 V, TA = −40°C to +85°C
Symbol
Characteristic
Min
ICC
Power Supply Current (All outputs enabled)
Voutdiff
CML Differential Output Swing (Note 4, Figures 5 and 12)
VCMR
(Note 6)
CML Output Common Mode Voltage (Loaded 50 W to VCC)
VID
Differential Input Voltage (VIHD − VILD)
640
Typ
Max
Unit
130
170
mA
800
1000
mV
VCC − 200
CML Single−Ended Input Voltage Range
mV
VCC − 0.8
VCC + 0.4
mV
300
1600
mV
LVTTL CONTROL INPUT PINS
VIH
Input HIGH Voltage (LVTTL Inputs)
VIL
Input LOW Voltage (LVTTL Inputs)
IIH
Input HIGH Current (LVTTL Inputs)
IIL
2000
mV
800
mV
−10
10
mA
Input LOW Current (LVTTL Inputs)
−10
10
mA
RTIN
CML Single−Ended Input Resistance
42.5
50
57.5
W
RTOUT
Differential Output Resistance
85
100
115
W
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
4. CML outputs require 50 W receiver termination resistors to VCC for proper operation (Figure 10).
5. Input and output parameters vary 1:1 with VCC.
6. VCMR min varies 1:1 with VEE, VCMR max varies 1:1 with VCC.
Table 6. AC CHARACTERISTICS VCC = 3.0 V to 3.6 V, VEE = 0 V (Note 7, Figure 9)
−40°C
Symbol
Characteristic
Min
Typ
VOUTPP
Output Voltage Amplitude (@ VINPPmin) fin ≤ 2 GHz
(See Figure 3)
fin ≤ 3 GHz
fin ≤ 3.5 GHz
280
235
170
365
310
220
fDATA
Maximum Operating Data Rate
3.2
tPLH,
tPHL
Propagation Delay to Output Differential
tSKEW
Duty Cycle Skew (Note 8)
Within−Device Skew (Figure 4)
Device−to−Device Skew (Note 12)
tJITTER
RMS Random Clock Jitter (Note 10) fin v 3.2 GHz
Peak−to−Peak Data Dependent Jitter fin = 2.5 Gb/s
(Note 11)
fin = 3.2 Gb/s
tr
tf
Output Rise/Fall Times @ 0.5 GHz
(20% − 80%)
Min
Typ
280
235
170
365
310
220
Max
3.2
140
225
340
5
5
20
0.15
7
7
Crosstalk−Induced RMS Jitter (Note 13)
Input Voltage Swing/Sensitivity
(Differential Configuration) (Note 9)
Max
85°C
Min
Typ
280
235
170
365
310
220
Max
Unit
mV
3.2
Gb/s
ps
D/D to Q/Q
VINPP
25°C
140
225
340
25
25
85
5
5
20
0.5
20
20
0.15
7
7
0.5
150
Q, Q
800
80
135
140
225
340
25
25
85
5
5
20
25
25
85
ps
0.5
20
20
0.15
7
7
0.5
20
20
ps
0.5
ps
800
mV
135
ps
0.5
150
800
80
135
150
80
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
7. Measured by forcing VINPP (MIN) from a 50% duty cycle clock source. All loading with an external RL = 50 W to VCC. Input edge rates 40 ps
(20% − 80%).
8. Duty cycle skew is measured between differential outputs using the deviations of the sum of Tpw− and Tpw+ @ 0.5 GHz.
9. VINPP (MAX) cannot exceed 800 mV. Input voltage swing is a single−ended measurement operating in differential mode.
10. Additive RMS jitter using 50% duty cycle clock input signal.
11. Additive peak−to−peak data dependent jitter using input data pattern with PRBS 223−1 and K28.5, VINPP = 400 mV.
12. Device to device skew is measured between outputs under identical transition @ 0.5 GHz.
13. Data taken on the same device under identical condition.
http://onsemi.com
5
450
20
400
18
350
16
14
300
TIME (ps)
OUTPUT VOLTAGE AMPLITUDE (mV)
NB4N840M
250
200
150
12
10
8
Channel B
6
100
4
50
Channel A
2
0
0.05 0.5
1
1.5
2
2.5
3
3.5
4
4.5
0
5
−40
25
85
INPUT CLOCK FREQUENCY (GHz)
TEMPERATURE (°C)
Figure 3. Output Voltage Amplitude (VOUTPP)
vs. Input Clock Frequency (fIN) at Ambient
Temperature (Typ)
Figure 4. Within−Device Skew vs. Temperature
at VCC = 3.3 V
900
170
800
160
600
CURRENT (mA)
VOLTAGE (mV)
700
500
400
300
150
140
130
200
120
100
25
110
−40
85
25
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 5. CML Differential Voltage vs.
Temperature
Figure 6. Supply Current vs. Temperature
(All 4 Outputs Enabled)
VOLTAGE (50 mV/div)
VOLTAGE (50 mV/div)
0
−40
DDJ = 4 ps
DDJ = 3 ps
TIME (80.4 ps/div)
TIME (62.5 ps/div)
Figure 7. Typical Output Waveform at 2.488 Gb/s
with PRBS 223−1 (Input Signal DDJ = 12 ps)
Figure 8. Typical Output Waveform at 3.2 Gb/s
with K28.5 (Input Signal DDJ = 14 ps)
http://onsemi.com
6
85
NB4N840M
Dx
VINPP = VIH(DX) − VIL(DX)
Dx
Qx
VOUTPP = VOH(QX) − VOL(QX)
Qx
tPHL
tPLH
Figure 9. AC Reference Measurement
VCC
50 W
50 W
Zo = 50 W
Q
D
Receiver
Device
Driver
Device
Zo = 50 W
Q
D
Figure 10. Typical Termination for Output Driver and Device Evaluation
(See Application Note AND8173/D)
VCC
50 W
VCC
50 W
50 W
50 W
QX
DX
QX
DX
16 mA
GND
Input
GND
GND
Output
Figure 11. CML Input and Output Structure
http://onsemi.com
7
NB4N840M
640 mV
MIN
QX
320 mV
MIN
QX
(QX − QX)
QX
1000 mV
MAX
500 mV
MAX
QX
(QX − QX)
Figure 12. CML Output Levels
ORDERING INFORMATION
Package
Shipping
NB4N840MMNG
Device
QFN32
(Pb−Free)
74 Units / Rail
NB4N840MMNR4G
QFN32
(Pb−Free)
1000 / Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
8
NB4N840M
PACKAGE DIMENSIONS
PIN ONE
LOCATION
ÉÉ
ÉÉ
0.15 C
2X
2X
QFN32 5*5*1 0.5 P
CASE 488AM−01
ISSUE O
A
B
D
NOTES:
1. DIMENSIONS AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED
TERMINAL AND IS MEASURED BETWEEN
0.25 AND 0.30 MM TERMINAL
4. COPLANARITY APPLIES TO THE EXPOSED
PAD AS WELL AS THE TERMINALS.
E
DIM
A
A1
A3
b
D
D2
E
E2
e
K
L
TOP VIEW
0.15 C
(A3)
0.10 C
A
32 X
0.08 C
SEATING
PLANE
A1
SIDE VIEW
MILLIMETERS
MIN
NOM MAX
0.800 0.900 1.000
0.000 0.025 0.050
0.200 REF
0.180 0.250 0.300
5.00 BSC
2.950 3.100 3.250
5.00 BSC
2.950 3.100 3.250
0.500 BSC
0.200
−−−
−−−
0.300 0.400 0.500
C
SOLDERING FOOTPRINT*
L
EXPOSED PAD
32 X
D2
9
16
K
5.30
32 X
17
8
3.20
E2
32 X
0.63
1
24
32
25
32 X b
0.10 C A B
3.20
e
5.30
0.05 C
BOTTOM VIEW
32 X
0.28
28 X
0.50 PITCH
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
9
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NB4N840M/D