HITACHI HA12179F

HA12179F
Audio Signal Processer for Car Deck and Cassette Deck
(Dolby B-type NR with PB Amp)
ADE-207-136
1st Edition
Apr. 1994
Description
HA12179F is silicon monolithic bipolar IC providing Dolby noise reduction system*, line mute, music
sensor and PB equalizer system in one chip.
Functions
• Line mute
× 2 channel
• PB equalizer
× 2 channel
• Dolby B-NR
× 2 channel
• Music sensor
× 1 channel
Features
• Different type of PB equalizer characteristics selection (normal/chrome or metal) is available with fully
electronic control switching built-in.
• Line mute ON/OFF is available.
• Changeable to Foward, Reverse-mode for PB head with fully electronic control switching built-in.
• Available to change music sensing level by external resistor.
• Music sensing level selection is available with fully electronic control switching built-in.
• Available to change frequency response of music sensor.
• NR-ON/OFF and REC/PB fully electronic control switching built-in.
• Pin compatible of HA12163 series except for 4 and 39 Pins.
*
Dolby is a trademark of Dolby Laboratories Licensing Corporation.
A license from Dolby Laboratories Licensing Corporation is required for the use of this IC.
HA12179F
Ordering Information
HA12179F
Package
PB-OUT level
REC OUT level
Dolby level
QFP 56
387.5 mVrms
300 mVrms
300 mVrms
PB-OUT level above shown is typical value when adjusting Dolby level at Rec-out with NR-off mode.
Rev.1, Apr. 1994, page 2 of 40
– +
120/70
41
–
1
120/70
EQOUT (R)
56
55
54
2
+
52 VREF (R)
F/R
53
51
50 GND
49 GND
48
F/R
47 VRER (L)
46
45
44
43
42
EQOUT (L)
38
4
6
37
PBOUT (R)
5
MUTE
+
–
MUTE
39
LINEOUT (R)
BIAS
3
×1
×1
40
RIP
+
7
36
PB OUT (L)
LINE OUT (L)
34
8
9
DOLBY B-NR
LPF
FF
DOLBY B-NR
35
32
10
12
13
14
15
16
17
18
19
D GND 20
21
DET MSV
CC
VCC 22
23
24
25
27
MS GND
26
VCC
To Microcomputer
+
NR ON/OFF
REC/PB
MUTE ON/OFF
120µ/70µ
F/R
MS GV
MSOUT
FFI
31
30 29
NOI
MS VREF
28
RECOUT (R)
11
MS AMP.
–
+
NO
33
RECOUT (L)
HA12179F
Block Diagram
Rev.1, Apr. 1994, page 3 of 40
HA12179F
Pin Discription (VCC = 9 V Single supply, Ta = 25°C, No signal, The value in the table
show typical value.)
Pin No.
Terminal
name
Zin
DC
voltage Equivalent circuit
2
TAI
100 kΩ VCC/2
Description
Tape input
41
VCC/2
5
MUI
Mute circuit input
25
MSI
Music sensor
rectifier input
10
NR DET
—
2.5 V
Time constant
pin for rectifier
BIAS
—
0.28 V
Reference
current input
38
33
3
GND
24
MS DET
—
VCC
Time constant
pin for rectifier
GND
40
RIP
—
Rev.1, Apr. 1994, page 4 of 40
VCC/2
Ripple filter
HA12179F
Pin Discription (VCC = 9 V Single supply, Ta = 25°C, No signal, The value in the table
show typical value.) (cont)
Pin No.
Terminal
name
Zin
DC
voltage Equivalent circuit
Description
43
EQ OUT
—
VCC/2
Equalizer output
56
VCC
GND
6
PB OUT
Play back
37
(Decode) output
30
MS VREF
Reference
voltage buffer
output
26
MA OUT
Music sensor
amp. output
47
VREF
Reference
52
12
voltage buffer
output
REC OUT
Recording
31
4
(Encode) output
LINE OUT
Mute circuit
39
44
output
EQ OUT-M
—
VCC/2
Equalizer output
(Metal)
VCC
GND
55
Rev.1, Apr. 1994, page 5 of 40
HA12179F
Pin Discription (VCC = 9 V Single supply, Ta = 25°C, No signal, The value in the table
show typical value.) (cont)
Pin No.
Terminal
name
Zin
DC
voltage Equivalent circuit
21
MS OUT
—
—
Description
MS VCC
Music sensor
output to MPU
D GND
22
VCC
—
VCC
—
Power supply
23
MS VCC
20
D GND
—
0.0 V
—
Digital (Logic)
ground
27
MS GND
Music sensor
ground
49
GND
Ground
50
48
FIN
—
51
46
PB-EQ input for
forward
RIN
53
45
VCC/2
PB-EQ input for
reverse
NFI
54
Negative
feedback
terminal of PBEQ amp.
28
NOI
Negative
feedback input
for normal speed
29
FFI
Negative
feedback input
for FF or REW
Rev.1, Apr. 1994, page 6 of 40
HA12179F
Pin Discription (VCC = 9 V Single supply, Ta = 25°C, No signal, The value in the table
show typical value.) (cont)
Pin No.
Terminal
name
Zin
DC
voltage Equivalent circuit
14
ON/OFF
122 kΩ —
Description
Mode control
input
22k
100k
D GND
GND
15
REC/PB
16
MUTE
17
120 µ/70 µ
18
F/R
19
MS GV
1
NC
No connection
7
8
9
11
13
32
34
35
36
42
Absolute Maximum Ratings
Item
Symbol
Ratings
Unit
Supply voltage
VCC max
16
V
Power dissipation
PT
400
mW
Operating temperature
Topr
–40 to +85
°C
Storage temperature
Tstg
–55 to +125
°C
Note
Ta ≤ 85 °C
Note: Operating voltage range is
VCC = 6.8 to 16.0 V
Rev.1, Apr. 1994, page 7 of 40
HA12179F
Electrical Characteristics (Ta = 25 °C Dolby Level 300 mVrms, VCC = 9.0 V)
Item
Symbol
Min
Typ
Max
Unit
Test conditions
Quiescent current
IQ
6.5
12.0
17.5
mA
PB mode, NR-ON, 70µ,
MUTE-OFF No signal
Input amp. gain
GvIA TAI
21.2
22.2
23.2
dB
Vin = 0 dB, f = 1 kHz
B-type encode
ENC-2 k (1)
2.8
4.3
5.8
dB
Vin = -20 dB, f = 2 kHz
boost
ENC-2 k (2)
7.0
8.5
10.0
Vin = -30 dB, f = 2 kHz
ENC-5 k (1)
1.7
3.2
4.7
Vin = -20 dB, f = 5 kHz
ENC-5 k (2)
6.7
8.2
9.7
Vin = -30 dB, f = 5 kHz
VO max
12.0
13.0
—
dB
THD = 1%, f = 1 kHz
64.0
70.0
—
dB
Rg = 5.1 kΩ, CCIR/ARM
Signal handling
Signal to noise ratio S/N
Remark
*1
THD
THD
—
0.05
0.3
%
Vin = 0 dB, f = 1 kHz
Channel
CT RL (1)
65.0
80.0
—
dB
Vin = 0 dB, f = 1 kHz
TAI IN
separation
CT RL (2)
50.0
60.0
—
Vin = 0.6 mVrms, f = 1 kHz
EQ IN
Mute attenuation
MUTE ATT
70.0
85.0
—
Vin = 0 dB, f = 1 kHz
TAI IN
PB-EQ gain
Gv EQ 1 k
37.0
40.0
43.0
Vin = 0.6 mVrms, f = 1 kHz
120 µ
Gv EQ 10 k (1) 33.0
36.0
39.0
Gv EQ 10 k (2) 29.0
32.0
35.0
PB-EQ maximum
output
VoM
300
600
—
mVrms THD = 1%, f = 1 kHz
PB-EQ THD
THD-EQ
—
0.05
0.3
%
Vin = 0.6 mVrms, f = 1 kHz
Noise voltage level
converted in input
VN
—
0.7
1.5
µVrms
Rg = 680 Ω DIN-AUDIO
MS sensing level
VON (1)
–36.0 –32.0 –28.0 dB
f = 5 kHz, Normal speed
VON (2)
–18.0 –14.0 –10.0
f = 5 kHz, High speed
dB
Vin = 0.6 mVrms, f = 10 kHz
70 µ
MS output low level VOL
—
1.0
1.5
V
MS output leak
current
IOH
—
0.0
2.0
µA
Control voltage
VIL
–0.2
—
1.0
V
VIH
3.5
—
5.3
Note:
1 VCC = 6.8 V
Rev.1, Apr. 1994, page 8 of 40
*1
L
OFF
Audio SG
TAI (R)
Note: 1. Resistor tolerance are ±1%
2. Capacitor tolerance are ±1%
3. Unit R: Ω C: F
AC VM1
SW17
ON
SW15
36
35
34
33
C17
0.1µ
31
C15
2.2 µ
32
+
30
29
C28
4700P
R28
18 k
R26
33 k
28
27
26
25
+
C13
0.33 µ
24 23
EQOUT (L)
LINEOUT (L)
RECOUT (L)
R27
330 k
R24
R25
330 k
47 k
C14
0.01µ
22
EQOUT (L)
LINEOUT (L)
RECOUT (L)
ON
SW23 SW24
L R
OFF
HA12179F (PB 1 CHIP)
QFP-56
GND FIN VREF RIN NFI EQ EQ N.C. TAI RIP LINE MUI PB N.C. N.C. N.C. NR N.C. REC MS FFI NOI MS MA MSI MS MS VCC
(L) (L) (L) (L) OUT-M OUT
(L)
OUT (L) OUT
DET
OUT VRFE
GND OUT
DET VCC
(L)
(L)
(L)
(L)
(L)
(L)
R33
5.1 k
R34
R38 R35 5.1 k C23
0.47 µ C19
C27
R41
330 k 5.1 k
22 µ
680
+
+ 2.2 µ
R40 C25 R36
C24
+
+
680 0.01µ 12 k
+
0.1µ
C26
C22
C35
22 µ
SW27
1µ
R37 18 k
0.1µ
49 48 47 46 45 44 43 42 41 40 39 38 37
R39
180
R29
10 k
SW21
SW22
R10
5.1 k
R14
10 k
Oscillo scope
Noise meter
with CCIR/ARM filter
and DIN-Audio filter
Noise meter
R15
10 k
ON
Distortion
analyzer
RECOUT (R)
LINEOUT (R)
EQOUT (R)
RECOUT (R)
LINEOUT (R)
EQOUT (R)
A GND
+ C29 (VCC)
100 µ
DC Source1
DC VM1
D GND
DC Source2
Note:
The capacitor (29) should
be connected.
It's recommended to be
connected close to the IC.
SW20
L
AC VM2
SW19
R
SW18
MSOUT
EQ EQ
LINE
PB
NR
REC
OUT MUI OUT
DET
OUT
FIN VREF RIN NFI OUT-M OUT
TAI
ON/ REC/
120 µ/
GND (R) (R) (R) (R) (R) (R) N.C. (R) BIAS (R) (R) (R) N.C. N.C. N.C. (R) N.C. (R) N.C. OFF PB MUTE 70 µ F/R MS GV D GVD MS OUT
50 51 52 53 54 55 56
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21
C33
C10
C32 +
SW26
+ 1µ
0.1 µ
22 µ
C34
C3
R6
R19
R17
0.1 µ
0.01 µ 18 k
C2
10 k
22k
C4
+
SW5
SW3
SW1 R23
22 µ
R8 0.1µ
+
C8
R7
120
µ 70 µ
PB
REC
SER
REP 3.9 k
+
+
R11
R1
R2
12 k 5.1 k
C12
18 k 2.2 µ
680
680
+
C1
R3 R5
2.2
µ
R9
22 µ
C5
180 330 k 5.1 k
SW16 EQIF (R)
SW6 MUTE SW4
SW2
0.47 µ
R
EQIR (R)
OFF MUTE FOR REV
OFF ON
SW25
TAI (L)
EQIR (L)
EQIF (L)
R30
10 k
HA12179F
Test Circuit
Rev.1, Apr. 1994, page 9 of 40
HA12179F
Application Note
Power Supply Range
Table 1
Supply Voltage
HA12179F
Single supply
6.8 V to 16.0 V
HA12179F is designed to operate on single supply. Please consult to HITACHI sales engineers when it will
use the split supply.
1. The lower limit of supply voltage depends on the line output reference level.
The minimum value of the overload margin is specified as 12 dB by Dolby Laboratories.
2.
In the reverse-voltage conditions such as 'D-GND is higher than VCC' or 'D-GND is lower than GND',
excessive current flows into the D-GND to destroy this IC. To prevent such destruction, pay attention
to the followings on using.Therefore, Short-circuit the D-GND and GND directory on the board
mounting this IC.
Reference Voltage
For the single supply operation this device provides the reference voltage of half the supply voltage that is
the signal grounds. As the peculiarity of these devices, the capacitor for the ripple filter is very small about
1/100 compared with their usual value. The Reference voltage are provided for the left channel and the
right channel separately. The block diagram is shown as figure 1.
22
47
VCC
–
L channel
reference
+
30 MS VREF
–
Music sensor
reference
R channel
reference
+
–
GND
49
50
VREF (L)
+
40
+ RIP
C22
1µ
52
VREF (R)
Figure 1 The Block Diagram of Reference Voltage Supply
Rev.1, Apr. 1994, page 10 of 40
HA12179F
Operating Mode Control
HA12179F provides electronic switching circuits. And each operating mode control are controlled by
parallel data (DC voltage).
Table 2
Threshold Voltage (VTH)
Pin No.
Lo
Hi
Unit
Test condition
14 15 16 17 18
19
–0.2 to 1.0
3.5 to 5.3
V
Input Pin
Measure
V
Table 3
Switching Truth Table
Pin No.
Lo
Hi
14
NR-OFF
NR-ON
15
PB
REC
16
MUTE-OFF
MUTE-ON
17
120 µ (NORMAL)
70 µ (METAL or CHROME)
18
FORWARD
REVERSE
19
SER (FF or REV)
REP (NORMAL SPEED)
Notes: 1. Each pins are on pulled down with 100 kΩ internal resistor.
Therefore, it will be low-level when each pins are open.
2. Over shoot level and under shoot level of input signal must be the standardized (High: 5.3 V,
Low: –0.2 V)
3. Reducing pop noise is so much better for 10 kΩ to 22 kΩ resistor and 1 µF to 22 µF capacitor
shown Fig 2. But the resistor connected to MUTE terminal (pin 16) should be under 10 kΩ.
INPUT Pin
10 to 22kΩ
MPU
+
1 to 22µF
Figure 2 Interface for Reduction of Pop Noise
Rev.1, Apr. 1994, page 11 of 40
HA12179F
Input Block Diagram and Level Diagram
R34
5.1k
R38
330k
R39
180
R35
5.1k
R36
12k
R37
18k
C25
0.01µ
C24
0.1µ
EQ OUT
TAI
EQ AMP.
NFI
PBOUT
30mVrms
(–28.2dBs)
EQ OUT-M
–
HA12179F : 387.5mVrms (–6.0dBs)
INPUT AMP
+
+
–
RIN
RECOUT
NR circuit
300mVrms
(–8.2dBs)
0.6mVrms
(–62.2dBs)
VREF
FIN
Note: The each level shown above is typical value when offering PBOUT level to PBOUT pin. (EQ AMP.)
Gv = 40 dB, f = 1 kHz
Figure 3 Input Block Diagram
Adjustment of Playback Dolby Level
After replace R34 and R35 with a half-fix volume of 10 kΩ, adjust RECOUT level to be Dolby level with
playback mode.
Note on Connecting with Tape Head to IC
This IC has no internal resistor to give the DC bias current to equalizer amp., therefore the DC bias current
will give through the head. This IC provides the Vref buffer output pin for Rch and Lch separately (has
two Vref terminal). In case of use that the Rch and Lch reference of head are connected commonly, please
use one of Vref terminals of IC (47 pin or 52 pin) for head reference.
If both 47 pin and 52 pin of IC are connected, rush current give the great damage to IC. The application
circuit is shown in figure 4.
Rev.1, Apr. 1994, page 12 of 40
HA12179F
43
44
–+
45
46
R/F
47 VREF(L)
48
49 GND
50 GND
51
52 VREF(R)
53
54
R/F
– +
55
56
Figure 4 Application Circuit
Rev.1, Apr. 1994, page 13 of 40
HA12179F
The Sensitivity Adjustment of Music Sensor
Adjusting MS AMP. gain by external resistor, the sensitivity of music sensor can set up.
R28
R27
R26
R25
C14
0.01µ
VCC
R24
330k
D VCC
+
C13
0.33µ
C28
4700P
MS
VREF
TAI (L)
×1
FFI NOI MA
OUT
IL
MSI MS
DET
RL
L·R signal addition circuit
–6dB
+
–
26dB
MS OUT
–
LPF
25kHz
DET
+
Microcomptuter
D GND
MS AMP.
×1
100k
D GND
TAI (R)
Figure 5 Music Sensor Block Diagram
Gv1
Normal speed
Gv
[dB]
FF or REV
100
1k
f [Hz]
Figure 6 Frequency Responce
Rev.1, Apr. 1994, page 14 of 40
f4
f3
Gv2
10
f2
f1
10k
25k
100k
HA12179F
• Normal mode
 R27 
 [dB]
Gv1= 20 log 1 +
 R28 
f1=
1
[Hz], f2 = 25 k [Hz]
2 ⋅π ⋅C14 ⋅100 k
• FF or REW mode
 R25 
Gv 2 = 20 log 1 +
 [dB]
 R26 
f3 =
1
[Hz], f4 = 25k [Hz]
2 ⋅ π⋅ C28⋅R26
A standard level of TAI pin is 30 mVrms and the gain for TAI to MS AMP input is 10times, therefore, the
other channel sensitivity of music sensor (S) is computed by the formula mentioned below.
C
1 
S = 20 log  ⋅
 [dB]
 30 10 ⋅ A 
A = MS AMP. gain (B dB)
C = The sensing level of music sensor
S = –7.3 – B[dB] C = 130 mVrms (typ.)
S is 6 dB up in case of the both channels.
Music Sensor Time Constant
• Sensing no signal to signal (Attack) is determind by C13.
0.01 µF to 1 µF capacitor C13 can be applicable.
• Sensing signal to no signal (Recovery) is determind by C13 and R24, however preceding (Attack), 100
kΩ to 1 MΩ R24 can be applicable.
Music Sensor Output (MS OUT)
As for the internal circuit of music sensor block, music sensor out pin is connected to the collector of NPN
Type directly, therefore, output level will be “high” when sensing no signal. And output level will be
“low” when sensing signal.
Connection with microcomputer, design IL at 1mA typ.
DVCC – MSOUTLo *
RL
* MSOUTLO: Sensing signal (about 1 V)
IL =
Notes: 1. Supply voltage of MS OUT pin must be less than VCC voltage.
2. MS VCC pin and VCC pin are required the same voltage.
Rev.1, Apr. 1994, page 15 of 40
HA12179F
The Tolerances of External Components for Dolby NR-block
For adequate Dolby NR tracking response, take external components shown below.
C17
0.1µ
±10%
37
36
35
34
33
PBout
(L)
NC
NC
NC
NR
DET (L)
HA12179F (PB1 CHIP)
BIAS
3
R11
18k
±2%
PBout
(R)
NC
NC
NC
NR
DET (R)
6
7
8
9
10
C10
0.1µ
±10%
Figure 7 Tolerances of External Components
Rev.1, Apr. 1994, page 16 of 40
HA12179F
PB Equalizer for Double Speed
PB equalizer can be design for double speed by using external components shown in figure 8. Application
data is shown in figure 9.
R35
5.1k
No : Normal speed
Do : Double speed
0.015µ
4.7µ
22k
VR1
R
No
0.1µ
+
Do
+
EQ OUT
R36
12k
R38
330k
R37
18k
C25
0.01µ
TAI
PBOUT
EQ OUT-M
EQ AMP.
NFI
INPUT AMP.
–
+
+
–
NR circuit
RECOUT
RIN
VREF
FIN
Note : Please adjust RECOUT level to
be Dolby level with volume of
VR1.
Figure 8 Application Circuit for Double Speed
Rev.1, Apr. 1994, page 17 of 40
HA12179F
60
50
Gv (dB)
40
120µ No :
Normal speed
70µ
R=2.7k
R=2.2k Do :
R=1.8k Double speed
R=1.3k
30
20
10
20
100
Note : OUTPUT = TAIpin
1k
10k
Frequency (Hz)
Figure 9 Application Data
Rev.1, Apr. 1994, page 18 of 40
100k
HA12179F
Quiescent Current vs.
Supply Voltage Characteristics (1)
Quiescent Current IQ (mA)
14
13
12
120 µ NR
NR
70 µ NR
NR
PBmode
MUTE-OFF
11
OFF
ON
OFF
ON
10
6
8
10
12
14
Supply Voltage (V)
16
Quiescent Current vs.
Supply Voltage Characteristics (2)
Quiescent Current IQ (mA)
14
13
12
120 µ NR
NR
70 µ NR
NR
PBmode
MUTE-ON
11
OFF
ON
OFF
ON
10
6
8
10
12
14
Supply Voltage (V)
16
Rev.1, Apr. 1994, page 19 of 40
HA12179F
Gain vs. Frequency Characteristics (PBmode)
30
VCC =9 V
NR-OFF
28
26
Gain (dB)
24
22
20
TAIin
LINEout
TAIin
RECout
18
16
14
12
10
10
100
1k
10 k
Frequency (Hz)
100 k
1M
Gain vs. Frequency Characteristics (RECmode)
30
VCC =9 V
NR-OFF
28
26
Gain (dB)
24
22
20
TAIin
LINEout
TAIin
RECout
18
16
14
12
10
10
100
Rev.1, Apr. 1994, page 20 of 40
1k
10 k
Frequency (Hz)
100 k
1M
HA12179F
Encode Boost vs. Frequency Characteristics (VCC = 6.8V,9V,16V)
10.8
VIN= –40 dB
9.6
8.4
Encode Boost (dB)
7.2
–30 dB
6.0
16 V
4.8
3.6
6.8 V,9 V
–20 dB
2.4
–10 dB
1.2
0
–1.2
100
0 dB
200
500
1k
2k
5k
10k
20k
Frequency (Hz)
1.2
Decode Cut vs. Frequency Characteristics (VCC=6.8V,9V,16V)
VIN=0 dB
0
–10 dB
–1.2
Decode Cut (dB)
–2.4
–20 dB
6.8 V,9 V
–3.6
–4.8
16 V
–6.0
–30 dB
–7.2
–8.4
–40 dB
–9.6
–10.8
100
200
500
1k
2k
Frequency (Hz)
5k
10k
20k
Rev.1, Apr. 1994, page 21 of 40
HA12179F
Maximum Output Level vs.
Supply Voltage Characteristics (1)
Maximum Output Level Vomax (dB)
25
NR-OFF
NR-ON
f=1 kHz
20
15
PB mode
TAIin →LINEOUT
10
6
8
10
12
14
Supply Voltage VCC (V)
16
Maximum Output Level vs.
Supply Voltage Characteristics (2)
Maximum Output Level Vomax (dB)
25
NR-OFF
NR-ON
f=1 kHz
20
15
REC mode
TAIin →RECOUT
10
6
Rev.1, Apr. 1994, page 22 of 40
8
10
12
14
Supply Voltage (V)
16
HA12179F
Signal to Noise Ratio vs. Supply
Voltage Characteristics
CCIR/ARM filter
90
Signal to Noise Ratio (dB)
PB NR-ON
REC NR-OFF
80
PB NR-OFF
REC NR-ON
70
0 dB = 300mVrms (RECmode, RECOUT)
0 dB = 387.5mVrms (PBmode, LINEOUT)
60
6
8
10
12
14
Supply Voltage (V)
16
Total Harmonic Distortion vs.
Supply Voltage Characteristics (1)
Total Harmonic Distortion T.H.D. (%)
1.0
TAI RECOUT
REC mode NR-ON
VIN = 0 dB
0.5
f=100 Hz
f=1 kHz
f=10 kHz
0.2
0.1
0.05
0.02
0.01
6
8
10
12
14
Supply Voltage VCC (V)
16
Rev.1, Apr. 1994, page 23 of 40
HA12179F
Total Harmonic Distortion vs.
Supply Voltage Characteristics (2)
Total Harmonic Distortion T.H.D. (%)
1.0
TAI RECOUT
REC mode NR-OFF
VIN = 0 dB
0.5
f=100 Hz
f=1 kHz
f=10 kHz
0.2
0.1
0.05
0.02
0.01
6
8
10
12
14
Supply Voltage VCC (V)
16
Total Harmonic Distortion vs.
Supply Voltage Characteristics (3)
Total Harmonic Distortion T.H.D. (%)
1.0
TAI LINEOUT
PB mode NR-ON
VIN = 0 dB
f=100 Hz
f=1 kHz
f=10 kHz
0.5
0.2
0.1
0.05
0.02
0.01
6
Rev.1, Apr. 1994, page 24 of 40
8
10
12
14
Supply Voltage VCC (V)
16
HA12179F
Total Harmonic Distortion vs.
Supply Voltage Characteristics (4)
Total Harmonic Distortion T.H.D. (%)
1.0
TAI LINEOUT
PB mode NR-OFF
VIN = 0 dB
f=100 Hz
f=1 kHz
f=10 kHz
0.5
0.2
0.1
0.05
0.02
0.01
6
8
10
12
14
Supply Voltage VCC (V)
16
Total Harmonic Distortion vs.
Output Level Characteristics (1)
10
Total Harmonic Distortion T.H.D. (%)
5.0
100 Hz
1 kHz
10 kHz
2.0
1.0
0.5
0.2
0.1
0.05
VCC = 9 V
TAI
REC mode
REC mode NR-ON
0.02
0.01
–15
–10
–5
0
5
10
Output Level VOUT (dB)
15
20
Rev.1, Apr. 1994, page 25 of 40
HA12179F
Total Harmonic Distortion vs.
Output Level Characteristics (2)
10
Total Harmonic Distortion T.H.D. (%)
5.0
f = 100 Hz
f = 1 kHz
f = 10 kHz
2.0
1.0
0.5
VCC = 9 V
TAI
RECOUT
REC mode NR-OFF
0.2
0.1
0.05
0.02
0.01
–15
–10
–5
0
5
10
Output Level VOUT (dB)
15
20
15
20
Total Harmonic Distortion vs.
Output Level Characteristics (3)
10
Total Harmonic Distortion T.H.D. (%)
5.0
f = 100 Hz
f = 1 kHz
f = 10 kHz
2.0
1.0
0.5
0.2
VCC = 9 V
TAI
LINEOUT
PB mode NR-ON
0.1
0.05
0.02
0.01
–15
Rev.1, Apr. 1994, page 26 of 40
–10
–5
0
5
10
Output Level VOUT (dB)
HA12179F
Total Harmonic Distortion vs.
Output Level Characteristics (4)
10
Total Harmonic Distortion T.H.D. (%)
5.0
f = 100 Hz
f = 1 kHz
f = 10 kHz
2.0
1.0
0.5
0.2
VCC = 9 V
TAI
LINEOUT
PB mode NR-OFF
0.1
0.05
0.02
0.01
–15
–10
–5
0
5
10
15
20
Output Level VOUT (dB)
Rev.1, Apr. 1994, page 27 of 40
HA12179F
Total Harmonic Distortion vs. Frequency Characteristics (1)
Total Harmonic Distortion T.H.D. (%)
0.5
–10 dB
0 dB
+10 dB
Audio
Band
Pass
0.2
400 Hz High pass
+
80 kHz Low pass
0.1
0.05
0.02
VCC =9 V
TAI RECout
RECmode NR-ON
0.01
50
100
300
1k
Frequency (Hz)
3k
10 k
30 k
Total Harmonic Distortion vs. Frequency Characteristics (2)
Total Harmonic Distortion T.H.D. (%)
0.5
–10 dB
0 dB
+10 dB
VCC =9 V
TAI RECout
RECmode NR-OFF
Audio
Band
Pass
0.2
400 Hz High pass
+
80 kHz Low pass
0.1
0.05
0.02
0.01
50
100
Rev.1, Apr. 1994, page 28 of 40
300
1k
Frequency (Hz)
3k
10 k
30 k
HA12179F
Total Harmonic Distortion vs. Frequency Characteristics (3)
Total Harmonic Distortion T.H.D. (%)
0.5
–10 dB
0 dB
+10 dB
VCC =9 V
TAI LINEout
PBmode NR-ON
Audio
Band
Pass
0.2
400 Hz High pass
+
80 kHz Low pass
0.1
0.05
0.02
0.01
50
100
300
1k
Frequency (Hz)
3k
10 k
30 k
Total Harmonic Distortion vs. Frequency Characteristics (4)
Total Harmonic Distortion T.H.D. (%)
0.5
–10 dB
0 dB
+10 dB
VCC =9 V
TAI LINEout
PBmode NR-OFF
300
1k
Frequency (Hz)
Audio
Band
Pass
0.2
400 Hz High pass
+
80 kHz Low pass
0.1
0.05
0.02
0.01
50
100
3k
10 k
30 k
Rev.1, Apr. 1994, page 29 of 40
HA12179F
Channel Separation vs. Frequency Characteristics (1)
Channel separation (dB)
–20
–40
VCC =9 V
PBmode
TAIin Lch
Rch
–60
RECOUT NR-OFF
–80
RECOUT NR-ON
–100
–120
10
1k
10 k
100 k
Frequency (Hz)
Channel Separation vs. Frequency Characteristics (2)
Channel separation (dB)
–20
–40
VCC =9 V
PBmode
TAIin Lch
Rch
–60
LINEOUT NR-OFF
–80
–100
LINEOUT NR-ON
–120
10
1k
10 k
Frequency (Hz)
Rev.1, Apr. 1994, page 30 of 40
100 k
HA12179F
Channel Separation vs. Frequency Characteristics (3)
Channel separation (dB)
–20
–40
VCC =9 V
PBmode
EQin Lch
Rch
LINEOUT NR-OFF
–60
–80
LINEOUT NR-ON
–100
–120
10
1k
10 k
100 k
Frequency (Hz)
Channel Separation vs. Frequency Characteristics (4)
Channel separation (dB)
–20
–40
VCC =9 V
PBmode
EQin Rch
–60
Lch
LINEOUT NR-OFF
–80
LINEOUT NR-ON
–100
–120
10
1k
10 k
100 k
Frequency (Hz)
Rev.1, Apr. 1994, page 31 of 40
HA12179F
Crosstalk vs. Frequency Characteristics (1)
–20
Crosstalk (dB)
–40
FORWARD REVERSE
VCC = 9 V
PB mode
–60
LINE OUT
NR-OFF
–80
LINE OUT
NR-ON
–100
–120
100
1k
10 k
100 k
Frequency (Hz)
Crosstalk vs. Frequency Characteristics (2)
–20
Crosstalk (dB)
–40
REVERSE FORWARD
VCC = 9 V
PB mode
–60
LINE OUT
NR-OFF
–80
LINE OUT
NR-ON
–100
–120
100
1k
10 k
Frequency (Hz)
Rev.1, Apr. 1994, page 32 of 40
100 k
HA12179F
MUTE Attenuation vs. Frequency Characteristics
MUTE Aftenuation (dB)
0
–20
VCC = 9 V
TAIIN LINEOUT
PB mode
–40
–60
–80
–100
20
100
1k
10 k
100 k
Frequency (Hz)
Ripple Rejection Ratio R.R.R. (dB)
Ripple Rejection Ratio vs. Frequency Characteristics (1)
0
VCC = 9 V
PB mode
PBOUT, NO-OFF
–20
PBOUT, NR-ON
–40
EQOUT
–60
–80
20
100
1k
Frequency (Hz)
10 k
100 k
Rev.1, Apr. 1994, page 33 of 40
HA12179F
Ripple Rejection Ration R.R.R. (dB)
Ripple Rejection Ratio vs. Frequency Characteristics (2)
0
VCC = 9 V
REC mode
–20
RECOUT, NR-ON
–40
RECOUT, NR-OFF
–60
–80
20
100
1k
Frequency (Hz)
10 k
100 k
EQ-AMP. Gain vs. Frequency Characteristics
70
V CC = 9 V
Gain (dB)
60
50
40
120 µ
70 µ
30
20
20
50 100 200
500 1 k 2 k
5 k 10 k 20 k
Frequency (Hz)
Rev.1, Apr. 1994, page 34 of 40
50 k 100 k
HA12179F
EQout Maximum Output Level vs.
Supply Voltage
Maximum Output Voltage Vo max (dB)
40
: NR-OFF Normal (120 µ )
: NR-OFF Metal (70 µ )
: NR-ON Normal (120 µ)
: NR-ON Metal (70 µ )
35
30
EQin ← EQout
0 dB = 60 mVrms (EQout)
f = 1 kHz
T.H.D. = 1 %
25
6
8
10
12
14
Supply Voltage (V)
16
Signal to Noise Ratio vs. Supply Voltage
Signal to Noise Ratio S/N (dB)
65
: NR-ON (120 µ)
: NR-ON (70 µ)
: NR-OFF (120 µ)
: NR-OFF (70 µ)
60
55
f = 1 kHz
DIN-Audio
EQin ← LINEOUT
50
6
8
10
12
14
16
18
Supply Voltage (V)
Rev.1, Apr. 1994, page 35 of 40
HA12179F
Total Harmonic Distortion vs.
Supply Voltage Characteristics
1.0
Total Harmonic Distortion T.H.D. (%)
EQIN LINEOUT
VIN = +6 dB
0.5
0.1
0.05
0.01
6
10
5.0
Total Harmonic Distortion T.H.D. (%)
NR-OFF 120µ
NR-ON 120µ
NR-OFF 70µ
NR-ON
70µ
2.0
8
10
12
14
Supply Voltage VCC (V)
16
Total Harmonic Distortion vs.
Output Level Characteristics
NR-OFF 120µ
NR-ON 120µ
NR-OFF 70µ
70µ
NR-ON
1.0
0.5
0.2
0.1
0.05
VCC = 9 V
EQin LINEOUT
f = 1 kHz
0.02
0.01
–15
Rev.1, Apr. 1994, page 36 of 40
–10
–5
0
5
10
Output Level (dB)
15
20
HA12179F
MS-Amp. Gain vs. Frequency
VCC = 9V
45
Repeat
MAOUT Measure
25
Search
15 MSI Measure
5
10
20
40 60 100
200 400 600 1 k 2 k 4 k 6 k 10 k 20 k 40 k 60 k 100 k
Frequency (Hz)
MS Sensing Level vs. Frequency
+10
MS Sensing Level (dB)
Gain (dB)
35
0
Search
–10
–20
–30 V = 9 V
CC
1 channel Input
–40 0 dB = 387.5 mV at PBOUT
High Low (Non-music to Music)
Low High (Music to Non-music)
–50
30
100
300
1k
3k
Frequency (Hz)
Repeat
10 k
30 k
100 k
Rev.1, Apr. 1994, page 37 of 40
HA12179F
Signal Sensing Time vs. Capacitance
(Music Sensor)
1000
VCC
22
PBOUT
500
MSOUT
200
Ta
R24
MSDET
24
Tr
+
C13
330 k
Signal Sensing Time (ms)
100
50
Tr
20
10
Ta
5
VCC = 9 V
f = 5 kHz
TAIin
Repeat
0 dB
–20 dB
2
1.0
0.5
0.2
0.005µ 0.01µ 0.02 µ
0.05µ 0.1µ 0.2 µ
0.5 µ
1µ
Capacitance C13 (F)
Signal Sensing Time vs. Resistance
(Music Sensor)
1000
VCC
22
PBOUT
Signal Sensing Time (ms)
500
0.33µ
Ta
200
+ C13
R24
MSOUT
Tr
MSDET
24
Recomended value of R24
is 100kΩ to 1MΩ
100
Tr
50
Ta
20
10
5
3
20 k
Rev.1, Apr. 1994, page 38 of 40
VCC = 9 V
f = 5 kHz
TAI
Repeat
0 dB
–20 dB
50 k 100 k 200 k 500 k
Resistance R24 ( Ω)
1M
2M
HA12179F
Package Dimensions
Unit: mm
12.8 ± 0.3
10.0
42
29
28
56
15
14
0.10
0.13 M
1.40
0˚ – 5˚
0.1
0.3 ± 0.10
0.15 ± 0.05
1
2.54 Max
0.65
12.8 ± 0.3
43
Hitachi Code
JEDEC Code
EIAJ Code
Weight
FP-56
Rev.1, Apr. 1994, page 39 of 40
HA12179F
Disclaimer
1. Hitachi neither warrants nor grants licenses of any rights of Hitachi’s or any third party’s patent,
copyright, trademark, or other intellectual property rights for information contained in this document.
Hitachi bears no responsibility for problems that may arise with third party’s rights, including
intellectual property rights, in connection with use of the information contained in this document.
2. Products and product specifications may be subject to change without notice. Confirm that you have
received the latest product standards or specifications before final design, purchase or use.
3. Hitachi makes every attempt to ensure that its products are of high quality and reliability. However,
contact Hitachi’s sales office before using the product in an application that demands especially high
quality and reliability or where its failure or malfunction may directly threaten human life or cause risk
of bodily injury, such as aerospace, aeronautics, nuclear power, combustion control, transportation,
traffic, safety equipment or medical equipment for life support.
4. Design your application so that the product is used within the ranges guaranteed by Hitachi particularly
for maximum rating, operating supply voltage range, heat radiation characteristics, installation
conditions and other characteristics. Hitachi bears no responsibility for failure or damage when used
beyond the guaranteed ranges. Even within the guaranteed ranges, consider normally foreseeable
failure rates or failure modes in semiconductor devices and employ systemic measures such as failsafes, so that the equipment incorporating Hitachi product does not cause bodily injury, fire or other
consequential damage due to operation of the Hitachi product.
5. This product is not designed to be radiation resistant.
6. No one is permitted to reproduce or duplicate, in any form, the whole or part of this document without
written approval from Hitachi.
7. Contact Hitachi’s sales office for any questions regarding this document or Hitachi semiconductor
products.
Sales Offices
Hitachi, Ltd.
Semiconductor & Integrated Circuits.
Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan
Tel: Tokyo (03) 3270-2111 Fax: (03) 3270-5109
URL
NorthAmerica
: http://semiconductor.hitachi.com/
Europe
: http://www.hitachi-eu.com/hel/ecg
Asia
: http://sicapac.hitachi-asia.com
Japan
: http://www.hitachi.co.jp/Sicd/indx.htm
For further information write to:
Hitachi Semiconductor
(America) Inc.
179 East Tasman Drive,
San Jose,CA 95134
Tel: <1> (408) 433-1990
Fax: <1>(408) 433-0223
Hitachi Europe GmbH
Electronic Components Group
Dornacher Straße 3
D-85622 Feldkirchen, Munich
Germany
Tel: <49> (89) 9 9180-0
Fax: <49> (89) 9 29 30 00
Hitachi Europe Ltd.
Electronic Components Group.
Whitebrook Park
Lower Cookham Road
Maidenhead
Berkshire SL6 8YA, United Kingdom
Tel: <44> (1628) 585000
Fax: <44> (1628) 585160
Hitachi Asia Ltd.
Hitachi Tower
16 Collyer Quay #20-00,
Singapore 049318
Tel : <65>-538-6533/538-8577
Fax : <65>-538-6933/538-3877
URL : http://www.hitachi.com.sg
Hitachi Asia Ltd.
(Taipei Branch Office)
4/F, No. 167, Tun Hwa North Road,
Hung-Kuo Building,
Taipei (105), Taiwan
Tel : <886>-(2)-2718-3666
Fax : <886>-(2)-2718-8180
Telex : 23222 HAS-TP
URL : http://www.hitachi.com.tw
Hitachi Asia (Hong Kong) Ltd.
Group III (Electronic Components)
7/F., North Tower,
World Finance Centre,
Harbour City, Canton Road
Tsim Sha Tsui, Kowloon,
Hong Kong
Tel : <852>-(2)-735-9218
Fax : <852>-(2)-730-0281
URL : http://www.hitachi.com.hk
Copyright  Hitachi, Ltd., 2000. All rights reserved. Printed in Japan.
Colophon 2.0
Rev.1, Apr. 1994, page 40 of 40