HITACHI HA12166F

HA12163 Series
Audio Signal Processor for Car Deck and Cassette Deck
(Dolby B-type NR with PB Amp)
ADE-207-059C (Z)
4th Edition
Jun. 1999
Description
HA12163 series are silicon monolithic bipolar IC providing Dolby noise reduction system*, music sensor
and PB equalizer system in one chip.
Functions
• PB equalizer × 2 channel
• Dolby B-NR × 2 channel
• Music sensor × 1 channel
Features
• Different type of PB equalizer characteristics selection (normal/chrome or metal) is available with fully
electronic control switching built-in.
• 2 type of input selection (radio/tape) is available.
• Changeable to forward, reverse-mode for PB head with fully electronic control switching built-in.
• Available to change music sensing level by external resistor.
• Music sensing level selection is available with fully electronic control switching built-in.
• Available to change frequency response of music sensor.
• NR-on/off and REC/PB fully electronic control switching built-in.
• 4 type of PB-out level.
• Available to allow common PCB designs with HA12173 series.
*
Dolby is a trademark of Dolby Laboratories Licensing Corporation.
A license from Dolby Laboratories Licensing Corporation is required for the use of this IC.
HA12163 Series
Ordering Information
HA12163
PB-OUT level
Dolby level
REC-OUT level
Unit
Package
300
300
300
mVrms
FP–56
HA12166F
FP–48
HA12164
450
300
300
mVrms
FP–56
HA12165
580
300
300
mVrms
FP–56
HA12160
550
300
300
mVrms
FP–56
Notes: 1. PB-OUT level above shown is typical value when adjusting Dolby level at Rec-out with NR-off
mode.
2. HA12166F is only changes by package from HA12163. It is the same electrical characteristics
that HA12163.
Absolute Maximum Ratings
Item
Supply voltage
1
Symbol
Ratings
Unit
VCC max
16
V
2
Power dissipation*
Pd
400*
mW
Operating temperature
Topr
–40 to +85
°C
Storage temperature
Tstg
–55 to +125
°C
Notes: 1. Value at Ta ≤ 85°C
2. HA12166F = 360 mW
Operating Voltage Range
Type
Min
Max
Unit
HA12163, HA12166F
6.5
16
V
HA12164
7.2
16
V
HA12165
8.5
16
V
HA12160
8.2
16
V
Note:
1. The minimum operating voltage of HA12163 series are different from the HA12173 series (Dolby
B/C–type).
Rev.4, Jun. 1999, page 2 of 66
HA12163 Series
Block Diagram (HA12163/164/165/160)
RADIO
IN(L)
EQOUT(L)
PBOUT(L)
RECOUT(L)
+
42
41
40
39
38
37
36
35
34
33
32
RIP
43
31
30
29
MS VREF
28
120/70
27
44
MS GND
– +
45
26
DOLBY B-NR
T/R
46
25
R/F
24
47 VREF (L)
48
DET MS VCC
49 GND
–
+
–
50 GND
LPF
VCC
+
VCC
22
21
MS AMP
+
23
MS OUT
To Microcomputer
D GND 20
51
19
52 VREF (R)
T/R
R/F
DOLBY B-NR
53
18
17
54
MS GV (S/R)
F/R
120 µ/70 µ
From
– +
16
55
120/70
15
56
TAPE/RADIO
Microcomputer
REC/PB
BIAS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
NR ON/OFF
EQOUT(R)
RADIO
IN(R)
PBOUT(R)
RECOUT(R)
Rev.4, Jun. 1999, page 3 of 66
HA12163 Series
Block Diagram (HA12166F)
RADIO
IN(L) PBOUT(L)
EQOUT(L)
35
36
RECOUT(L)
+
34
33
32
31
30
29
28
27
26
25
MS VREF
RIP
37
MS GND 24
120/70
– +
38
23
S/R
DOLBY B-NR
39
40 VREF(L)
22
T/R
F/R
21
×1
41
+
VCC
DET MS VCC 20
MS AMP.
42
43
GND
VCC 19
–
+
–
GND
LPF
+
18 MS OUT
44
45
To Microcomputer
D GND 17
×1
VREF(R)
F/R
46
16
15
T/R
DOLBY B-NR
47
14
– +
120/70
13
48
MS GV (S/R)
F/R
120 µ/70 µ
From
TAPE/RADIO
BIAS
1
2
3
4
5
6
7
8
9
10
11
12
REC/PB
EQOUT(R)
ON/OFF
RADIO PBOUT(R)
IN(R)
Rev.4, Jun. 1999, page 4 of 66
RECOUT(R)
Microcomputer
HA12163 Series
Electrical Characteristics (Ta = 25°C Dolby level 300 mVrms (Rec-out pin))
HA12163, HA12166F VCC = 9.0 V
HA12165 VCC = 12 V
Item
Symbol
HA12164 VCC = 9.0 V
HA12160 VCC = 9.0 V
Min
Typ
Max
Unit
Test conditions
Note
Quiescent current IQ
6.0
11.0
17.0
mA
No input
No Signal
NR-ON,70 µ
Input
HA12163
GvIA TAI
18.5
20.0
21.5
dB
Vin = 0 dB, f = 1 kHz
amp
HA12166F GvIA RAI
15.5
17.0
18.5
gain
HA12164
GvIA TAI
22.0
23.5
25.0
GvIA RAI
19.0
20.5
22.0
HA12165
GvIA TAI
24.2
25.7
27.2
GvIA RAI
21.2
22.7
24.2
GvIA TAI
23.7
25.2
26.7
GvIA RAI
20.7
22.2
23.7
B-type encode
ENC –2k (1)
2.8
4.3
5.8
Boost
ENC –2k (2)
7.0
8.5
10.0
Vin = –30 dB, f = 2 kHz
ENC –5k (1)
1.7
3.2
4.7
Vin = –20 dB, f = 5 kHz
HA12160
Vin = 0 dB, f = 1 kHz
Vin = 0 dB, f = 1 kHz
Vin = 0 dB, f = 1 kHz
dB
Vin = –20 dB, f = 2 kHz
ENC –5k (2)
6.7
8.2
9.7
Signal handling
Vo max
12.0
13.0
—
dB
THD = 1%, f = 1 kHz
Signal to noise
ratio
S/N
64.0
70.0
—
dB
Rg = 5.1 kΩ, CCIR/ARM
THD
THD
—
0.05
0.3
%
Vin = 0 dB, f = 1 kHz
Channel
CT RL (1)
70.0
85.0
—
dB
Vin = 0 dB, f = 1 kHz
RAI input
separation
CT RL (2)
50.0
60.0
—
Vin = 0.6 mVrms, f = 1 kHz
EQ input
Crosstalk
CT EQ → RAI 70.0
80.0
—
CT RAI → EQ 50.0
60.0
—
Gv EQ 1k
37.0
40.0
43.0
Gv EQ 10k (1) 33.0
36.0
39.0
Gv EQ 10k (2) 29.0
32.0
35.0
600
—
PB - EQ gain
PB - EQ maximum VoM
output
PB - EQ THD
THD - EQ
300
Vin = –30 dB, f = 5 kHz
*1
EQ input
dB
Vin = 0 dB, f = 1 kHz
RAI input
Vin = 0.6 mVrms, f = 1 kHz
120 µ
Vin = 0.6 mVrms, f = 10 kHz
70 µ
mVrms THD = 1%, f = 1 kHz
—
0.05
0.3
%
Noise voltage level VN
converted in input
—
0.7
1.5
µVrms Rg = 680 Ω, DIN - AUDIO
MS sensing level
VON (1)
–36.0 –32.0 –28.0 dB
f = 5 kHz, Normal speed
VON (2)
–18.0 –14.0 –10.0
f = 5 kHz, High speed
*1
Vin = 0.6 mVrms, f = 1 kHz
Rev.4, Jun. 1999, page 5 of 66
HA12163 Series
Electrical Characteristics (Ta = 25°C Dolby level 300 mVrms (Rec-out pin)) (cont)
HA12163, HA12166F VCC = 9.0 V
HA12165 VCC = 12 V
HA12164 VCC = 9.0 V
HA12160 VCC = 9.0 V
Item
Symbol
Min
Typ
Max
Unit
MS output low
level
VOL
—
1.0
1.5
V
MS output leak
current
IOH
—
0.0
2.0
µA
Control voltage
VIL
–0.2
—
1.5
V
VIH
3.5
—
5.3
Note:
Test conditions
Note
1. HA12163 HA12166F VCC = 6.5 V, HA12164 VCC = 7.2 V, HA12165 VCC = 8.5 V,HA12160 VCC = 8.2
V
Rev.4, Jun. 1999, page 6 of 66
L
R
AC VM1
SW17
ON
SW15
SW25
OFF
SW16
R1
680
51
GND
50
+ C1
22 µ
VREF
(R)
FIN
(R)
C25
0.01 µ
RIN
(R)
RIN
(L)
C2
22 µ
+
R2
680
R3
180
C3
0.01 µ
R5
330 k
R7
12 k
R6
18 k
56
EQ
EQ
NFI OUT-M OUT
(R)
(R)
(R)
55
C24
0.1 µ
R35
5.1 k
2
TAI
(R)
TAI
(L)
C4
0.1 µ
R8
5.1 k
1
N.C.
N.C.
R33
5.1 k
R9
5.1 k
3
R11
18 k
BIAS
RIP
+
N.C.
PB
OUT
(L)
N.C.
38 37 36
C19
2.2 µ
N.C.
NR
DET
(L)
35 34 33
N.C.
C15
2.2 µ
C8
2.2 µ +
5
N.C.
R10
5.1 k
C5
0.47 µ
+
4
RAI
(R)
R14
10 k
6
PB
OUT
(R)
7
N.C.
8
N.C.
9
N.C.
10
N.C.
N.C.
REC
OUT
(R)
REC
OUT
(L)
C12
2.2 µ
+
C28
4700 p
R28
18 k
EQOUT(L)
R25
47 k
R27
330 k
RECOUT(L)
PBOUT(L)
ON/
OFF
FFI
RAD
MS
GV
MS
DET
SW11
SW1
SW10
EQOUT(R)
PBOUT(R)
RECOUT(R)
EQOUT(R)
PBOUT(R)
RECOUT(R)
SW8
R23
3.9 k
SW20
L
AC VM2
SW19
R
SW18
MSOUT
SW21
SW22
Note
1) Resistor tolerance are ±1%
2) Capacitor tolerance are±1%
3) Unit R: Ω C: F
DISTORTION
ANALYZER
SW9
REP
R22
22 k
21
20
SW2
SER
22
V CC
MS
OUT
MS
VCC
OFF
D
GND
R21
22 k
FOR REV
OSCILLO SCOPE
NOISE METER
with CCIR/ARM filter
and DIN-AUDIO filter
F/R
MSI
23
C13
0.33 µ
+
R
ON
RECOUT(L)
SW24
25 24
70 µ
SW3
120 µ
R20
22 k
R19
22 k
SW4
SW12
TAP
SW13
REC
SW5
R18
22 k
C33
22 µ +
PB
SW6
R17
22 k
MA
OUT
R24
330 k
L
EQOUT(L)
PBOUT(L)
16 17 18 19
OFF ON
C32
22 µ +
MS
GND
REC TAPE/ 120µ
/PB RADIO /70µ
NOI
13 14 15
N.C.
MS
VREF
SW23
C14
0.01 µ
30 29 28 27 26
R26
33 k
NOISE METER
R15
10 k
11 12
C10
0.1 µ
NR
DET
(R)
+
R29
10 k
32 31
C17
0.1 µ
HA12163/4/5/0 (PB 1 CHIP)
RAI
(L)
40 39
C22
C23
1 µ + 0.47 µ +
R34
5.1 k
43 42 41
NFI
EQ
EQ
(L) OUT-M OUT
(L)
(L)
R37
18 k
R36
12 k
R38
330 k
46 45 44
+
R40
680
R39
180
52 53 54
VREF
(L)
FIN
(L)
C26
22 µ
48 47
R41
680
49
C27
22 µ
GND
AUDIO SG
RAI(R)
EQIR(R)
EQIF(R)
EQIF(L)
EQIR(L)
RAI(L)
R30
10 k
A GND
DC SOURCE1
C29
100 µ
D GND
DC SOURCE3
DC SOURCE2
5V
5V
Note) The capacitor(C29) should
be connected.
It's recommended to be
connected close to the IC.
+
DC VM1
HA12163 Series
Test Circuit
HA12163/164/165/160
Rev.4, Jun. 1999, page 7 of 66
Rev.4, Jun. 1999, page 8 of 66
R
OFF
SW16
EQIR(L)
+ C1
22 µ
R1
680
44 45
43
C2
22 µ
VREF RIN
(R)
(R)
+
R2
680
R3
180
1
R5
330 k
R7
12 k
R6
18 k
48
EQ
EQ
OUT-M OUT
(R)
(R)
EQ
EQ
OUT-M OUT
(L)
(L)
C3
0.01 µ
46 47
NFI
(R)
NFI
(L)
FIN
(R)
RIN
(L)
R37
18 k
R36
12 k
R38
330 k
37 36
C25
0.01 µ
GND
R40
680
40 39 38
+
VREF
(L)
C26
22 µ
FIN
(L)
R41
680
42 41
C27
22 µ
R39
180
GND
+
AUDIO SG
RAI(R)
EQIR(R)
EQIF(R)
EQIF(L)
Note
1) Resistor tolerance are ±1%
2) Capacitor tolerance are±1%
3) Unit R: Ω C: F
AC VM1
SW17
ON
SW15
L
SW25
RAI(L)
RIP
RAI
(L)
34 33
PB
OUT
(L)
N.C.
N.C.
32 31 30
+
C19
2.2 µ
R8
5.1 k
2
TAI
(R)
R9
5.1 k
C4
0.1 µ
3
R11
18 k
BIAS
+
4
R10
5.1 k
C5
0.47 µ
RAI
(R)
5
PB
OUT
(R)
+
R14
10 k
C8
2.2 µ
6
N.C.
7
N.C.
HA12166 (PB 1 CHIP)
TAI
(L)
R33
5.1 k
C22
C23
1 µ + 0.47 µ +
R34
5.1 k
35
R35
5.1 k
R30
10 k
C12
2.2 µ
8
9
REC
OUT
(R)
REC
OUT
(L)
+
C28
4700 p
R28
18 k
R25
47 k
R27
330 k
RECOUT(L)
PBOUT(L)
EQOUT(L)
ON/
OFF
FFI
RAD
FOR
70 µ
SW3
R20
22 k
OSCILLO SCOPE
NOISE METER
with CCIR/ARM filter
and DIN-AUDIO filter
REV
R22
22 k
R23
3.9 k
EQOUT(R)
PBOUT(R)
RECOUT(R)
EQOUT(R)
PBOUT(R)
RECOUT(R)
SW8
REP
SW1
DISTORTION
ANALYZER
SW9
SER
SW2
R21
22 k
SW11 SW10
120 µ
SW4
SW12
TAP
SW13
REC
SW5
R19
22 k
18
17
C33
22 µ +
R18
22 k
19
V CC
13 14 15 16
MS
VCC
20
OFF
ON
MS
OUT
F/R
MS
DET
22 21
MSI
C13
0.33 µ
+
R
SW24
RECOUT(L)
D
GND
PB
SW6
R17
22 k
MA
OUT
R24
330 k
L
EQOUT(L)
PBOUT(L)
MS
GV
OFF ON
C32
22 µ +
MS
GND
REC TAPE/ 120µ
/PB RADIO /70µ
NOI
10 11 12
N.C.
MS
VREF
SW23
C14
0.01 µ
27 26 25 24 23
R26
33 k
NOISE METER
R15
10 k
C10
0.1 µ
NR
DET
(R)
NR
DET
(L)
29 28
C17
0.1 µ
+
C15
2.2 µ
R29
10 k
SW20
L
AC VM2
SW19
R
SW18
MSOUT
SW21
SW22
+
A GND
D GND
DC SOURCE3
DC SOURCE2
5V
5V
Note) The capacitor(C29) should
be connected.
It's recommended to be
connected close to the IC.
C29
100 µ
DC SOURCE1
DC VM1
HA12163 Series
HA12166F
HA12163 Series
Pin Description (VCC = 9 V Single supply, Ta = 25°C, No signal, The value in the table
show typical value)
Pin No.
Terminal
DC
QFP-48 QFP-56 name
Zin
2
2
100 kΩ VCC/2
35
41
TAI
voltage Equivalent circuit
Description
Tape input
VCC / 2
4
4
33
39
RAI
Radio input
22
25
MSI
Music sensor
rectifier input
8
10
NR DET
—
2.5 V
Time
constant pin
for rectifier
29
33
3
3
BIAS
—
0.28 V
Reference
current input
GND
Rev.4, Jun. 1999, page 9 of 66
HA12163 Series
Pin Description (VCC = 9 V Single supply, Ta = 25°C, No signal, The value in the table
show typical value) (cont)
Pin No.
Terminal
DC
QFP-48 QFP-56 name
Zin
voltage Equivalent circuit
Description
21
—
VCC
Time
constant pin
for rectifier
24
MS DET
GND
16
19
MS GV
100 kΩ —
Mode control
input
DGND
GND
34
40
RIP
Rev.4, Jun. 1999, page 10 of 66
—
VCC/2
Ripple filter
HA12163 Series
Pin Description (VCC = 9 V Single supply, Ta = 25°C, No signal, The value in the table
show typical value) (cont)
Pin No.
Terminal
DC
QFP-48 QFP-56 name
Zin
voltage Equivalent circuit
Description
1
43
—
VCC/2
Equalizer
36
56
EQ OUT
V CC
output
GND
5
6
PB OUT
Play back
32
37
27
30
MS VREF
Reference
voltage buffer
output
23
26
MA OUT
Music sensor
amp output
40
47
VREF
45
52
9
12
28
31
(Decode)
output
Reference
voltage buffer
output
REC OUT
Recording
(Encode)
output
Rev.4, Jun. 1999, page 11 of 66
HA12163 Series
Pin Description (VCC = 9 V Single supply, Ta = 25°C, No signal, The value in the table
show typical value) (cont)
Pin No.
Terminal
DC
QFP-48 QFP-56 name
Zin
voltage Equivalent circuit
Description
37
44
—
VCC/2
Equalizer
48
55
EQ OUT-M
VCC
output
(Metal)
GND
MS VCC
18
21
MS OUT
—
—
Music sensor
output to
MPU
19
22
VCC
—
VCC
—
Power supply
20
23
MS VCC
17
20
D GND
—
0.0 V
—
Digital (Logic)
ground
24
27
MS GND
Music sensor
ground
42
49
GND
Ground
43
50
D GND
Rev.4, Jun. 1999, page 12 of 66
HA12163 Series
Pin Description (VCC = 9 V Single supply, Ta = 25°C, No signal, The value in the table
show typical value) (cont)
Pin No.
Terminal
DC
QFP-48 QFP-56 name
Zin
voltage Equivalent circuit
Description
41
48
—
VCC/2
PB - EQ
44
51
39
46
46
53
38
45
47
54
25
28
NOI
Negative
feedback
input for
Normal
speed
26
29
FFI
Negative
feedback
input for FF
or REW
FIN
input for
Forward
RIN
PB - EQ
input for
Reverse
NFI
Negative
feedback
terminal of
PB - EQ amp
Rev.4, Jun. 1999, page 13 of 66
HA12163 Series
Pin Description (VCC = 9 V Single supply, Ta = 25°C, No signal, The value in the table
show typical value) (cont)
Pin No.
Terminal
DC
QFP-48 QFP-56 name
Zin
11
100 kΩ —
14
ON/OFF
voltage Equivalent circuit
Description
Mode control
input
D GND
GND
12
15
REC/PB
13
16
TAPE/
RADIO
14
17
120 µ/70 µ
15
18
F/R
6
1
NC
7
5
10
7
30
8
31
9
11
13
32
34
35
36
38
42
Rev.4, Jun. 1999, page 14 of 66
—
—
—
No
connection
HA12163 Series
Application Note
1. Power Supply Range
HA12163 series are provided with four line output level, which will permit on optimum overload
margin for power supply conditions. And this series are designd to operate on single supply only.
In case of split supply use, please consult with sales engineer.
Table 1
Supply Voltage
Single supply
HA12163
HA12164
HA12165
HA12160
6.5 V to 16.0 V
7.2 V to 16.0 V
8.5 V to 16.0 V
8.2 V to 16.0 V
A. The lower limit of supply voltage depends on the line output reference level.
The minimum value of the overload margin is specified as 12 dB by Dolby Laboratories.
B. In the reverse-voltage conditions such as ‘D-GND is higher than VCC’ or ‘D-GND is lower than
GND’, excessive current flows into the D-GND to destory this IC. To prevent such destruction, pay
attention to the followings on using.
Short-circuit the D-GND and GND directory on the board mounting this IC.
2. Reference Voltage
These devices provide the reference voltage of half the supply voltage that is the signal grounds. As the
peculiarity of these devices, the capacitor for the ripple filter is very small about 1/100 compared
with their usual value. The Reference voltage are provided for the left channel and the right channel
separately. The block diagram is shown as figure 1.
22
47 VREF(L)
VCC
+
–
L channel
reference
+
–
+
–
GND 49
50
40 RIP
+
C22
1µ
30 MS VREF
Music sensor
reference
R channel
reference
52 VREF(R)
Figure 1 The Block Diagram of Reference Voltage Supply
Rev.4, Jun. 1999, page 15 of 66
HA12163 Series
3. Operating Mode Control
HA12163 series provide fully electronic switching circuits. And each operating mode control are
controlled by parallel data (DC voltage).
Table 2
Threshold Voltage (VTH)
Pin No.
Low
High
Unit
Test conditions
14, 15, 16, 17,
18, 19
–0.2 to 1.5
3.5 to 5.3
V
Input Pin
Measure
22 k
V
Table 3
Switching Truth Table
Pin No.
Low
High
14
NR - OFF
NR - ON
15
PB
REC
16
TAPE
RADIO
17
120 µ (NORMAL)
70 µ (METAL or CHROME)
18
FORWARD
REVERSE
19
SER (FF or REV)
REP (NORMAL SPEED)
Notes: 1. Each pins are on pulled down with 100 kΩ internal resistor.
Therefore, it will be low-level when each pins are open.
2. Over shoot level and under shoot level of input signal must be the standardized (High: 5.3 V,
Low: –0.2 V)
3. When connecting microcomputer or Logic-IC with HA12163 series directly, there is apprehension
of rush-current under some transition timming of raising voltage or falling voltage at VCC ON/OFF.
On using, connect protective resistors of 10 to 22 kΩ to all the control pins. It is shown is test
circuit on this data sheet. And pins fixed to low level should be preferably open.
4. Pay attention not to make digital GND voltage lower than GND voltage.
Rev.4, Jun. 1999, page 16 of 66
HA12163 Series
4. Input Block Diagram and Level Diagram
HA12163:
HA12164:
HA12165:
HA12160:
R34
5.1 k
R35
5.1 k
R38
330 k
R39
180
R36
12 k
R37
18 k
C25
0.01 µ
300 mVrms (–8.2 dBs)
450 mVrms (–4.7 dBs)
580 mVrms (–2.5 dBs)
550 mVrms (–2.9 dBs)
C24
0.1 µ
EQ OUT
TAI
EQ OUT-M
30 mVrms
(–28.2 dBs)
–
PBOUT
42.4 mVrms
(–25.2 dBs)
INPUT AMP.
EQ AMP.
NFI
RAI
+
+
NR circuit
–
RIN
RECOUT
300 mVrms
(–8.2 dBs)
0.6 mVrms
(–62.2 dBs)
VREF
FIN
The each level shown above is typical value
when offering PBOUT level to PBOUT pin.
(EQ AMP Gv = 40 dB f = 1 kHz)
Figure 2 Input Block Diagram
5. Adjustment of Playback Dolby Level
After replace R34 and R35 with a half-fix volume of 10 kΩ, adjust RECOUT level to be Dolby level
with playback mode.
Rev.4, Jun. 1999, page 17 of 66
HA12163 Series
6. Note on Connecting with Tape Head to IC
This IC has no internal resistor to give the DC bias current to equalizer amp, therefore the DC bias
current will give through the head. This IC provides the Vref buffer output pin for Rch and Lch
separately (has two Vref terminal). In case of use that the Rch and Lch reference of head are
connected commonly, please use one of Vref terminals of IC (47 pin or 52 pin) for head reference.
If both 47 pin and 52 pin of IC are connected, rush current give the great damage to IC. The
application circuit is shown in figure 3.
43
44
–+
45
46
R/F
47 VREF(L)
48
49 GND
50 GND
51
52 VREF(R)
R/F
53
54
–+
55
56
Figure 3 Application Circuit
Rev.4, Jun. 1999, page 18 of 66
HA12163 Series
7. The Sensitivity Adjustment of a Music Sensor
Adjusting MS AMP gain by external resistor, the sensitivity of music sensor can set up.
R28
R27
R26
R25
DVCC
VCC
C14
0.01 µ
R24
330 k
+ C13
0.33 µ
IL
C28
4700 p
TAI (L)
X1
MS
VREF
FFI
NOI
MA MSI MS
OUT
DET
RL
L·R signal addition circuit
–6 dB
MS OUT
+
DET
+
LPF
Microcomputer
–
–
D GND
26 dB
25 kHz
MS AMP.
100 k
X1
D GND
TAI (R)
Figure 4 Music Sensor Block Diagram
Gv1
f1
f2
Normal speed
Gv
[dB]
f3
Gv2
f4
FF or REV
10
100
1k
f
10 k
25 k
100 k
[Hz]
Figure 5 Frequency Response
Rev.4, Jun. 1999, page 19 of 66
HA12163 Series
A. Normal mode
R27

Gv1 = 20 log 1 +
 [dB]

R28
1
[Hz], f 2 = 25 k [Hz]
f1 =
2 ⋅π ⋅C14⋅100 k
B. FF or REW mode
 R25 
Gv2 = 20 log 1 +
 [dB]
 R26 
f3 =
1
[Hz], f4 = 25k [Hz]
2 ⋅π ⋅C28 ⋅ R26
A standard level of TAI pin is 30 mVrms and the gain for TAI to MS AMP input is 10, therefore,
the other channel sensitivity of music sensor (S) is computed by the formula mentioned below.
C
1 
S = 20 log  ⋅
 [dB]
 30 10⋅ A 
A = MS AMP. gain (B dB)
C = The sensing level of music sensor
S = –7.3–B [dB]
C = 130 mVrms (typ.)
S is 6 dB up in case of the both channels.
8. Music Sensor Output (MS OUT)
As for the internal circuit of music sensor block, music sensor output pin is connected to the collector of
NPN Type directly, therefore, output level will be “high” when sensing no signal. And output level
will be “low” when sensing signal.
Connection with microcomputer, design IL at 1 mA typ.
DVCC – MSOUTLo *
IL =
RL
* MSOUTLo: sensing signal (about 1 V)
Notes: 1. Supply voltage of MS OUT pin must be less than VCC voltage.
2. MS VCC pin and VCC pin are required the same voltage.
Rev.4, Jun. 1999, page 20 of 66
HA12163 Series
9. The Tolerances of External Components for Dolby NR-block
For adequate Dolby NR tracking response, take external components shown below.
C17
0.1 µ
±10%
37
36
35
34
33
PB OUT
(L)
NC
NC
NC
NR
DET (L)
HA12163 series (PB 1 CHIP)
BIAS
PB OUT
(R)
NC
NC
NC
NR
DET (R)
3
6
7
8
9
10
R11
18 k
±2%
C10
0.1 µ
±10%
Unit R: Ω
C: F
Figure 6 Tolerances of External Components
Rev.4, Jun. 1999, page 21 of 66
HA12163 Series
10. PB Equalizer for Double Speed
PB equalizer can be design for double speed by using external components shown in figure 7.
Application data is shown in figure 8.
R35
5.1 k
No : Normal speed
Do : Double speed
0.015 µ
4.7 µ
+
22 k
VR1
R
No
0.1 µ
Do
EQ OUT
R38
330 k
R39
180
R36
12 k
EQ
OUT-M
R37
18 k
C25
0.01 µ
EQ
AMP.
– +
NFI
* Please ajust RECOUT level to
be Dolby level with volume of
VR 1.
+
TAI
RAI
PBOUT
INPUT AMP.
+
–
NR
circuit
RECOUT
RIN
VREF
Unit R: Ω
C: F
FIN
Figure 7 Application Circuit for Double Speed
60
G V (dB)
50
40
30
120 µ
No (Normal speed)
70 µ
R = 2.7 k
R = 2.2 k
Do (Double speed)
R = 1.8 k
R = 1.3 k
20
10
20
100
1k
10 k
Frequency (Hz)
100 k
* OUTPUT = TAIpin
Figure 8 Application Data
Rev.4, Jun. 1999, page 22 of 66
HA12163 Series
Typical Characteristic Curves
Quiescent Current vs. Supply Voltage
13
HA12163/164/165/160/166F
PB-OFF (NORMAL mode)
PB-ON (NORMAL mode)
PB-ON (METAL or CHROME mode)
Quiescent Current I CC (mA)
12
11
10
9
6
8
10
12
14
16
Supply Voltage V CC (V)
Rev.4, Jun. 1999, page 23 of 66
HA12163 Series
HA12163 Data
TAIin Input Amp. Gain vs. Frequency (PBmode)
22
HA12163/166F
18
Gain (dB)
PBOUT NR-OFF, RECOUT NR-ON/OFF
14
10
6
V CC = 9 V
2
10
100
1k
10 k
100 k
500 k
Frequency (Hz)
RAIin Input Amp. Gain vs. Frequency (RECmode)
22
HA12163/166F
Gain (dB)
18
14
PBOUT NR-ON/OFF, RECOUT NR-OFF
10
6
V CC = 9 V
2
10
100
1k
10 k
Frequency (Hz)
Rev.4, Jun. 1999, page 24 of 66
100 k
500 k
HA12163 Series
Encode Boost vs. Frequency (V CC = 6.5 V, 9 V, 16 V)
10.8
HA12163/166F
Vin = –40 dB
9.6
8.4
Encode Boost (dB)
–30 dB
7.2
6.0
16 V
4.8
–20 dB
6.5 V, 9 V
3.6
2.4
–10 dB
1.2
0 dB
0
–1.2
100
200
500
1k
2k
Frequency (Hz)
5k
10 k
20 k
Decode Cut vs. Frequency (V CC = 6.5 V, 9 V, 16 V)
1.2
HA12163/166F
Vin = 0 dB
0
–10 dB
–1.2
Decode Cut (dB)
–2.4
–20 dB
6.5 V, 9 V
–3.6
–4.8
–6.0
16 V
–30 dB
–7.2
–8.4
–9.6
–10.8
100
–40 dB
200
500
1k
2k
Frequency (Hz)
5k
10 k
20 k
Rev.4, Jun. 1999, page 25 of 66
HA12163 Series
Maximum Output Level Vo max (dB)
Maximum Output Level vs. Supply Voltage (1)
(RAIin RECmode RECOUT)
25
HA12163/166F
20
NR-ON
NR-OFF
f = 1 kHz
0 dB = 300mVrms
T.H.D. = 1 %
15
10
6
8
14
10
12
Supply Voltage VCC (V)
16
Maximum Output Level Vo max (dB)
Maximum Output Level vs. Supply Voltage (2)
(RAIin PBmode PBOUT)
25
HA12163/166F
20
NR-ON
NR-OFF
f = 1kHz
0 dB = 300mVrms
T.H.D. = 1 %
15
10
6
8
10
12
14
Supply Voltage VCC (V)
Rev.4, Jun. 1999, page 26 of 66
16
HA12163 Series
Signal to Noise Ratio vs. Supply Voltage
90
HA12163/166F
Signal to Noise Ratio S/N (dB)
RECmode NR-OFF
PBmode NR-ON
PBmode NR-OFF
80
RECmode NR-ON
70
↓
f = 1 kHz
CCIR / ARM
RAIin PBOUT, RECOUT
Total Harmonic Distortion T.H.D. (%)
60
6
8
10
14
12
Supply Voltage VCC (V)
16
Total Harmonic Distortion vs. Supply Voltage (1)
(RAIin RECmode RECOUT NR-ON)
1.0
fin = 100 Hz
HA12163/166F
1 kHz
0.5
10 kHz
0.2
0.1
0.05
0.02
0.01
6
8
10
12
14
16
Supply Voltage VCC (V)
Rev.4, Jun. 1999, page 27 of 66
Total Harmonic Distortion T.H.D. (%)
HA12163 Series
Total Harmonic Distortion vs. Supply Voltage (2)
(RAIin RECmode RECOUT NR-OFF)
1.0
fin = 100 Hz
HA12163/166F
1 kHz
0.5
10 kHz
0.2
0.1
0.05
0.02
0.01
6
8
10
12
14
16
Total Harmonic Distortion T.H.D. (%)
Supply Voltage VCC (V)
Total Harmonic Distortion vs. Supply Voltage (3)
(RAIin PBmode PBOUT NR-ON)
1.0
HA12163/166F
fin = 100 Hz
1 kHz
0.5
10 kHz
0.2
0.1
0.05
0.02
0.01
6
8
10
12
14
Supply Voltage VCC (V)
Rev.4, Jun. 1999, page 28 of 66
16
Total Harmonic Distortion T.H.D. (%)
HA12163 Series
Total Harmonic Distortion vs. Supply Voltage (4)
(RAIin PBmode PBOUT NR-OFF)
1.0
HA12163/166F
fin = 100 Hz
1 kHz
0.5
10 kHz
0.2
0.1
0.05
0.02
0.01
6
8
10
12
14
16
Supply Voltage VCC (V)
Total Harmonic Distortion vs. Output Level (1)
(RAIin RECmode RECOUT NR-ON)
Total Harmonic Distortion T.H.D. (%)
5
HA12163/166F
fin = 100 kHz
1 kHz
10 kHz
V CC = 9 V
2
1.0
0.5
0.2
0.1
0.05
0.02
0.01
−15
−10
−5
0
5
10
15
20
Output Level Vout (dB)
Rev.4, Jun. 1999, page 29 of 66
HA12163 Series
Total Harmonic Distortion vs. Output Level (2)
(RAIin RECmode RECOUT NR-OFF)
5
Total Harmonic Distortion T.H.D. (%)
HA12163/166F
2
fin = 100 kHz
1 kHz
10 kHz
VCC = 9 V
1.0
0.5
0.2
0.1
0.05
0.02
0.01
−15
−10
−5
0
5
10
15
20
Output Level Vout (dB)
Total Harmonic Distortion vs. Output Level (3)
(RAIin PBmode PBOUT NR-ON)
Total Harmonic Distortion T.H.D. (%)
5
HA12163/166F
2
fin = 100 kHz
1 kHz
10 kHz
VCC = 9 V
1.0
0.5
0.2
0.1
0.05
0.02
0.01
−15
−10
−5
0
5
10
Output Level Vout (dB)
Rev.4, Jun. 1999, page 30 of 66
15
20
HA12163 Series
Total Harmonic Distortion vs. Output Level (4)
(RAIin PBmode PBOUT NR-OFF)
5
Total Harmonic Distortion T.H.D. (%)
HA12163/166F
2
fin = 100 kHz
1 kHz
10 kHz
VCC = 9 V
1.0
0.5
0.2
0.1
0.05
0.02
0.01
−15
−10
−5
0
5
10
15
20
Total Harmonic Distortion T.H.D. (%)
Output Level Vout (dB)
Total Harmonic Distortion vs. Frequency (RAIin RECmode RECOUT NR-ON) (1)
0.2
HA12163/166F
0.1
0.05
+10 dB
0 dB
−10 dB
0.02
0.01
100
200
500
1k
2k
5k
10 k
20 k
Frequency (Hz)
Rev.4, Jun. 1999, page 31 of 66
Total Harmonic Distorion T.H.D. (%)
HA12163 Series
Total Harmonic Distortion vs. Frequency (RAIin RECmode RECOUT NR-OFF) (2)
0.2
HA12163/166F
+10 dB
0 dB
0.1
−10 dB
0.05
0.02
0.01
100
200
500
1k
2k
5k
10 k
20 k
Total Harmonic Distortion T.H.D. (%)
Frequency (Hz)
Total Harmonic Distortion vs. Frequency (RAIin PBmode PBOUT NR-ON) (3)
0.2
HA12163/166F
+10 dB
0 dB
0.1
−10 dB
0.05
0.02
0.01
100
200
500
1k
2k
Frequency (Hz)
Rev.4, Jun. 1999, page 32 of 66
5k
10 k
20 k
Total Harmonic Distortion vs. Frequency (RAIin PBmode PBOUT NR-OFF) (4)
0.2
HA12163/166F
+10 dB
0 dB
−10 dB
0.1
0.05
0.02
0.01
100
200
500
1k
2k
5k
10 k
20 k
Frequency (Hz)
−10
Crosstalk vs. Frequency (RADIO→TAPE) RECmode RECOUT
HA12163/166F
V CC = 9 V
−30
Crosstalk (dB)
Total Harmonic Distortion T.H.D. (%)
HA12163 Series
−50
NR-ON
−70
−90
−110
20
NR-OFF
50
100
200
500
1k
2k
5k
10 k 20 k
Frequency (Hz)
Rev.4, Jun. 1999, page 33 of 66
HA12163 Series
−10
Crosstalk vs. Frequency (RADIO→TAPE) PBmode PBOUT
HA12163/166F
V CC = 9 V
Crosstalk (dB)
−30
−50
−70
NR-OFF
−90
NR-ON
−110
20
50
100
200
500
1k
2k
5k
10 k 20 k
Frequency (Hz)
−20
Crosstalk vs. Frequency (L→R) RAIin, RECmode, RECOUT
HA12163/166F
V CC = 9 V
Crosstalk (dB)
−40
−60
NR-ON
−80
NR-OFF
−100
−120
20
50
100
200
500
1k
2k
Frequency (Hz)
Rev.4, Jun. 1999, page 34 of 66
5k
10 k 20 k
HA12163 Series
−20
Crosstalk vs. Frequency (L→R) RAIin, PBmode, PBOUT
HA12163/166F
V CC = 9 V
Crosstalk (dB)
−40
−60
−80
NR-OFF
−100
NR-ON
−120
20
50
100
200
500
1k
2k
5k
10 k 20 k
Frequency (Hz)
−20
Crosstalk vs. Frequency (R→L) RAIin, RECmode, RECOUT
HA12163/166F
V CC = 9 V
Crosstalk (dB)
−40
−60
−80
NR-ON
−100
NR-OFF
−120
20
50
100
200
500
1k
2k
5k
10 k 20 k
Frequency (Hz)
Rev.4, Jun. 1999, page 35 of 66
HA12163 Series
−20
Crosstalk vs. Frequency (R→L) RAIin, PBmode, PBOUT
HA12163/166F
V CC = 9 V
Crosstalk (dB)
−40
−60
−80
NR-OFF
−100
NR-ON
−120
20
50
100
200
500
1k
2k
5k
10 k 20 k
Frequency (Hz)
−10
Crosstalk vs. Frequency (TAPE→RADIO) PBmode PBOUT
HA12163/166F
V CC = 9 V
Crosstalk (dB)
−30
−50
−70
NR-OFF
−90
−110
20
NR-ON
50
100
200
500
1k
2k
Frequency (Hz)
Rev.4, Jun. 1999, page 36 of 66
5k
10 k 20 k
HA12163 Series
−10
Crosstalk vs. Frequency (FORWARD→REVERSE) PBmode
HA12163/166F
V CC = 9 V
Crosstalk (dB)
−30
−50
−70
NR-OFF
−90
−110
20
NR-ON
50
100
200
500
1k
2k
5k
10 k 20 k
Frequency (Hz)
−10
Crosstalk vs. Frequency (REVERSE→FORWARD) PBmode
HA12163/166F
V CC = 9 V
Crosstalk (dB)
−30
−50
−70
NR-OFF
−90
−110
20
NR-ON
50
100
200
500
1k
2k
5k
10 k 20 k
Frequency (Hz)
Rev.4, Jun. 1999, page 37 of 66
HA12163 Series
Crosstalk vs. Frequency (L→R) EQIFin, PBmode, PBOUT
0
HA12163/166F
V CC = 9 V
Crosstalk (dB)
−20
−40
−60
NR-OFF
−80
NR-ON
−100
20
50
100
200
500
1k
2k
5k
10 k 20 k
Frequency (Hz)
Crosstalk vs. Frequency (R→L) EQIFin, PBmode, PBOUT
0
HA12163/166F
V CC = 9 V
Crosstalk (dB)
−20
−40
−60
NR-OFF
−80
−100
20
NR-ON
50
100
200
500
1k
2k
Frequency (Hz)
Rev.4, Jun. 1999, page 38 of 66
5k
10 k 20 k
HA12163 Series
−10
Ripple Rejection Ratio vs. Frequency (RECmode RECOUT)
Ripple Rejection Ratio R.R.R (dB)
HA12163/166F
V CC = 9 V
−20
−30
NR-ON
−40
−50
NR-OFF
−60
20
50
100
200
500
1k
2k
5k
10 k 20 k
Frequency (Hz)
Ripple Rejection Ratio R.R.R (dB)
Ripple Rejection Ratio vs. Frequency (PBmode PBOUT, EQOUT)
−10
HA12163/166F
V CC = 9 V
−20
−30
PBOUT NR-ON
−40
−50
−60
20
PBOUT NR-OFF
EQOUT NR-ON/OFF
50
100
200
500
1k
2k
5k
10 k 20 k
Frequency (Hz)
Rev.4, Jun. 1999, page 39 of 66
HA12163 Series
EQ-AMP. Gain vs. Frequency
70
HA12163/164/165/160/166F
V CC = 9 V
Gain (dB)
60
50
40
120 µ
70 µ
30
20
20
50 100 200
500 1 k 2 k
5 k 10 k 20 k
Frequency
EQout Maximum Output Level vs.
Supply Voltage
Maximum Output Voltage Vo max (dB)
40
HA12163/164/165/160/166F
: NR-OFF Normal (120 µ )
: NR-OFF Metal (70 µ )
: NR-ON Normal (120 µ)
: NR-ON Metal (70 µ )
35
30
EQin ← EQOUT
0 dB = 60 mVrms (EQOUT)
f = 1 kHz
T.H.D. = 1 %
25
6
Rev.4, Jun. 1999, page 40 of 66
8
10
12
14
Supply Voltage (V)
16
50 k 100 k
HA12163 Series
Signal to Noise Ratio vs. Supply Voltage
65
: NR-ON (120 µ)
: NR-ON (70 µ)
: NR-OFF (120 µ)
: NR-OFF (70 µ)
Signal to Noise Ratio S/N (dB)
HA12163/166F
60
55
V CC = 9V
f = 1 kHz
DIN-Audio
EQin ← PBOUT
50
6
8
10
12
14
16
18
Supply Voltage (V)
Total Harmonic Distortion vs.
Supply Voltage (EQin PBOUT)
Total Harmonic Distortion T.H.D. (%)
0.5
HA12163/166F
EQin ← PBOUT
Vin = + 12 dB
0.2
0.1
0.05
: NR-ON (120 µ)
: NR-ON (70 µ)
: NR-OFF (120 µ)
: NR-OFF (70 µ)
0.02
0.01
6
8
10
12
14
Supply Voltage (V)
16
Rev.4, Jun. 1999, page 41 of 66
PBout and EQout T.H.D. (%)
HA12163 Series
PBOUT and EQOUT T.H.D. vs. Output Voltage
5
HA12163/166F
: PBOUT NR-OFF (120 µ)
: PBOUT NR-OFF (70 µ)
2
: PBOUT NR-ON (120 µ)
0 dB
: PBOUT NR-ON (70 µ)
= 60
: EQOUT (120 µ)
mVrms
1.0
: EQOUT (70 µ)
(EQOUT)
0.5
0 dB
= 300
mVrms
(PBOUT)
0.2
0.1
0.05
VCC = 9 V
0.02 f = 1 kHz
EQin ← EQOUT, PBOUT
0.01
−20
−10
0
10
20
Output Voltage (dB)
30
40
Total Harmonic Distortion vs. Frequency (EQin PBmode PBOUT)
0.5
Total Harmonic Distortion T.H.D. (%)
HA12163/166F
: NR-OFF 120
: NR-ON 120
: NR-OFF 70
: NR-ON 70
0.2
µ
µ
µ
µ
0.1
0.05
0.02
0.01
20
VCC = 9 V
EQin ← PBOUT
50
100
Rev.4, Jun. 1999, page 42 of 66
200
500
1k
Frequency (Hz)
2k
5k
10 k
20 k
HA12163 Series
MS-AMP. Gain vs. Frequency
50
HA12163/164/165/160/166F
MAOUT
40
Normal
30
MAOUT
20
FF or REV
10
MSI
0
20
50 100 200
500 1 k 2 k
5 k 10 k 20 k
50 k 100 k
Frequency (Hz)
MS Sensing Level vs. Frequency
15
HA12163/164/165/160/166F
5
MS Sensing Level (dB)
Gain (dB)
MSI
−5
−15
FF or REW
−25
Normal
−35
10
20
50 100 200
500 1 k 2 k
5 k 10 k 20 k 50 k 100 k
Frequency (Hz)
Rev.4, Jun. 1999, page 43 of 66
HA12163 Series
Sensing Time vs. Resistance
Sensing Time (ms)
500
HA12163/164/165/160/166F
VCC = 9 V
f = 5 kHz
TAI ← MSOUT
200
REPmode
: 0 dB
: −20 dB
100 0 dB : 300 mVrms
50
PBOUT
20
MSOUT
VCC
C13
0.33 µ
MS DET
10
50 k
100 k
200 k
+
R24
500 k
1M
Resistance R24 ( Ω)
Signal Sensing Time vs. Capacitance
Signal Sensing Time (ms)
50
HA12163/164/165/160/166F
VCC = 9 V
20 f = 5 kHz
TAI ← MSOUT
REPmode
10
5
2
1.0
0.5
0.2
0.01
Rev.4, Jun. 1999, page 44 of 66
: 0 dB
: −20 dB
: −30 dB
0 dB = 300 mVrms
PBOUT
MSOUT
VCC
C13
MS DET
+
R24
330 k
0.1
0.5
Capacitance C13 ( µF)
1.0
HA12163 Series
Encode Boost vs. Frequency (V CC = 7.2 V, 9 V, 16 V)
10.8
HA12164
Vin = –40 dB
9.6
8.4
Encode Boost (dB)
–30 dB
7.2
6.0
16 V
4.8
–20 dB
7.2 V, 9 V
3.6
2.4
–10 dB
1.2
0 dB
0
–1.2
100
200
500
1k
2k
Frequency (Hz)
5k
10 k
20 k
Decode Cut vs. Frequency (V CC = 7.2 V, 9 V, 16 V)
1.2
HA12164
Vin = 0 dB
0
–10 dB
–1.2
Decode Cut (dB)
–2.4
–20 dB
7.2 V, 9 V
–3.6
–4.8
–6.0
16 V
–30 dB
–7.2
–8.4
–9.6
–10.8
100
–40 dB
200
500
1k
2k
Frequency (Hz)
5k
10 k
20 k
Rev.4, Jun. 1999, page 45 of 66
HA12163 Series
TAIin Input Amp. Gain vs. Frequency (PBmode)
26
HA12164
Gain (dB)
22
PBOUT NR-OFF
18
RECOUT NR-ON/OFF
14
10
V CC = 9 V
6
10
100
1k
10 k
Frequency (Hz)
100 k
500 k
RAIin Input Amp. Gain vs. Frequency (RECmode)
26
HA12164
Gain (dB)
22
PBOUT NR-ON/OFF
18
RECOUT NR-OFF
14
10
V CC = 9 V
6
10
Rev.4, Jun. 1999, page 46 of 66
100
1k
10 k
Frequency (Hz)
100 k
500 k
HA12163 Series
Maximum Output Level Vo max (dB)
Maximum Output Level vs. Supply Voltage (1)
(RAIin RECmode RECOUT)
25
HA12164
20
15
NR-ON
NR-OFF
f = 1 kHz
T.H.D = 1 %
0 dB = 300 mVrms
10
6
8
10
12
14
16
Supply Voltage (V)
Maximum Output Level Vo max (dB)
Maximum Output Level vs. Supply Voltage (2)
(RAIin PBmode PBOUT)
25
HA12164
20
15
NR-ON
NR-OFF
f = 1 kHz
T.H.D = 1 %
0 dB = 450 mVrms
10
6
8
10
12
14
16
Supply Voltage (V)
Rev.4, Jun. 1999, page 47 of 66
HA12163 Series
Signal to Noise Ratio vs. Supply Voltage
90
HA12164
PBmode NR-ON
PBmode NR-OFF
80
RECmode NR-ON
70
←
Signal to Noise Ratio S/N (dB)
RECmode NR-OFF
RAIin PBOUT, RECOUT
VCC = 9 V
f = 1 kHz
CCIR/ARM
60
5
6
8
10
12
14
Supply Voltage (V)
16
Total Harmonic Distortion vs. Output Level (1)
(RAIin RECmode RECOUT NR-ON)
Total Harmonic Distortion T.H.D. (%)
HA12164
fin = 100 Hz
fin = 1 kHz
fin = 10 kHz
VCC = 9 V
2
1.0
0.5
0.2
0.1
0.05
0.02
0.01
−15
Rev.4, Jun. 1999, page 48 of 66
−10
−5
0
5
10
Output Level Vout (dB)
15
20
HA12163 Series
5
Total Harmonic Distortion vs. Output Level (2)
(RAIin RECmode RECOUT NR-OFF)
Total Harmonic Distortion T.H.D. (%)
HA12164
fin = 100 Hz
fin = 1 kHz
fin = 10 kHz
VCC = 9 V
2
1.0
0.5
0.2
0.1
0.05
0.02
0.01
−15
5
−10
−5
0
5
10
Output Level Vout (dB)
15
20
Total Harmonic Distortion vs. Output Level (3)
(RAIin PBmode PBOUT NR-ON)
Total Harmonic Distortion T.H.D. (%)
HA12164
fin = 100 Hz
fin = 1 kHz
fin = 10 kHz
VCC = 9 V
2
1.0
0.5
0.2
0.1
0.05
0.02
0.01
−15
−10
−5
0
5
10
Output Level Vout (dB)
15
20
Rev.4, Jun. 1999, page 49 of 66
HA12163 Series
Total Harmonic Distortion vs. Output Level (4)
(RAIin PBmode PBOUT NR-OFF)
5
Total Harmonic Distortion T.H.D. (%)
HA12164
fin = 100 Hz
fin = 1 kHz
fin = 10 kHz
VCC = 9 V
2
1.0
0.5
0.2
0.1
0.05
0.02
0.01
−15
−10
−5
0
5
10
Output Level Vout (dB)
15
20
Ripple Rejection Ratio vs. Frequency (RECmode)
−10
Ripple Rejection Ratio R.R.R (dB)
HA12164
VCC = 9V
−20
−30
NR-ON
−40
NR-OFF
−50
−60
20
Rev.4, Jun. 1999, page 50 of 66
50
100
2k
500 1k
Frequency (Hz)
200
5k
10k 20k
HA12163 Series
Ripple Rejection Ratio R.R.R (dB)
−10
Ripple Rejection Ratio vs. Frequency (PBmode)
HA12164
VCC = 9V
−20
−30
PBOUT NR-ON
−40
PBOUT NR-OFF
−50
EQOUT NR-ON/OFF
−60
20
50
100
2k
500 1k
Frequency (Hz)
200
5k
10k 20k
HA12165 Data
Encode Boost vs. Frequency (V CC = 8.5 V, 12 V, 16 V)
10.8
HA12165
Vin = –40 dB
9.6
8.4
Encode Boost (dB)
–30 dB
7.2
6.0
16 V
4.8
–20 dB
8.5 V, 12 V
3.6
2.4
–10 dB
1.2
0 dB
0
–1.2
100
200
500
1k
2k
Frequency (Hz)
5k
10 k
20 k
Rev.4, Jun. 1999, page 51 of 66
HA12163 Series
Decode Cut vs. Frequency (V CC = 8.5 V, 12 V, 16 V)
1.2
HA12165
Vin = 0 dB
0
–10 dB
–1.2
Decode Cut (dB)
–2.4
–20 dB
–3.6
8.5 V, 12 V
–4.8
–6.0
16 V
–30 dB
–7.2
–8.4
–9.6
–40 dB
–10.8
100
200
500
1k
2k
Frequency (Hz)
5k
10 k
20 k
TAIin Input Amp. Gain vs. Frequency (PBmode)
28
HA12165
24
Gain (dB)
PBOUT NR-OFF
20
RECOUT NR-ON/OFF
16
12
V CC = 12 V
8
10
Rev.4, Jun. 1999, page 52 of 66
100
1k
10 k
Frequency (Hz)
100 k
500 k
HA12163 Series
RAIin Input Amp. Gain vs. Frequency (RECmode)
28
HA12165
PBOUT NR-ON/OFF
20
16
RECOUT NR-OFF
12
V CC = 12 V
8
10
100
1k
10 k
Frequency (Hz)
100 k
500 k
Maximum Output Level vs. Supply Voltage (1)
(RAIin RECmode RECOUT)
20
HA12165
Maximum Output Level Vo max (dB)
Gain (dB)
24
15
10
NR-ON
NR-OFF
f = 1 kHz
T.H.D = 1 %
0 dB = 300 mVrms
5
6
8
10
12
14
16
Supply Voltage (V)
Rev.4, Jun. 1999, page 53 of 66
HA12163 Series
Maximum Output Level Vo max (dB)
Maximum Output Level vs. Supply Voltage (2)
(RAIin PBmode PBOUT)
20
HA12165
15
10
NR-ON
NR-OFF
f = 1 kHz
T.H.D = 1 %
0 dB = 580 mVrms
5
6
8
10
12
14
16
Supply Voltage (V)
Signal to Noise Ratio vs. Supply Voltage
90
RECmode NR-OFF
PBmode NR-ON
PBmode NR-OFF
80
RECmode NR-ON
70
←
Signal to Noise Ratio S/N (dB)
HA12165
RAIin PBOUT, RECOUT
VCC = 12 V
f = 1 kHz
CCIR/ARM
60
Rev.4, Jun. 1999, page 54 of 66
6
8
10
12
14
Supply Voltage (V)
16
18
HA12163 Series
Total Harmonic Distortion vs. Output Level (1)
(RAIin RECmode RECOUT NR-OFF)
5
Total Harmonic Distortion T.H.D. (%)
HA12165
fin = 100 Hz
fin = 1 kHz
fin = 10 kHz
VCC = 12 V
2
1.0
0.5
0.2
0.1
0.05
0.02
0.01
−15
5
−10
−5
0
5
10
Output Level Vout (dB)
15
20
Total Harmonic Distortion vs. Output Level (2)
(RAIin RECmode RECOUT NR-ON)
Total Harmonic Distortion T.H.D. (%)
HA12165
fin = 100 Hz
fin = 1 kHz
fin = 10 kHz
VCC = 12 V
2
1.0
0.5
0.2
0.1
0.05
0.02
0.01
−15
−10
−5
0
5
10
Output Level Vout (dB)
15
20
Rev.4, Jun. 1999, page 55 of 66
HA12163 Series
Total Harmonic Distortion vs. Output Level (3)
(RAIin PBmode PBOUT NR-ON)
10
HA12165
fin = 100 Hz
fin = 1 kHz
fin = 10 kHz
VCC = 12 V
Total Harmonic Distortion T.H.D. (%)
5
2
1.0
0.5
0.2
0.1
0.05
0.02
0.01
−15
10
−10
−5
0
5
10
Output Level Vout (dB)
20
15
Total Harmonic Distortion vs. Output Level (4)
(RAIin PBmode PBOUT NR-OFF)
HA12165
Total Harmonic Distortion T.H.D. (%)
5
fin = 100 Hz
fin = 1 kHz
fin = 10 kHz
VCC = 12 V
2
1.0
0.5
0.2
0.1
0.05
0.02
0.01
−15
Rev.4, Jun. 1999, page 56 of 66
−10
−5
0
5
10
Output Level Vout (dB)
15
20
HA12163 Series
−10
Ripple Rejection Ratio vs. Frequency (RECmode)
Ripple Rejection Ratio R.R.R (dB)
HA12165
VCC = 12V
−20
−30
NR-ON
−40
NR-OFF
−50
−60
20
−10
50
100
2k
500 1k
Frequency (Hz)
200
5k
10k 20k
Ripple Rejection Ratio vs. Frequency (PBmode)
Ripple Rejection Ratio R.R.R (dB)
HA12165
V CC = 12V
−20
−30
PBOUT NR-ON
−40
PBOUT NR-OFF
−50
−60
20
EQOUT NR-ON/OFF
50
100
2k
500 1k
Frequency (Hz)
200
5k
10k 20k
Rev.4, Jun. 1999, page 57 of 66
HA12163 Series
HA12160 Data
Encode Boost vs. Frequency (V CC = 8.2 V, 9 V, 16 V)
10.8
HA12160
Vin = –40 dB
9.6
8.4
Encode Boost (dB)
–30 dB
7.2
6.0
16 V
4.8
–20 dB
8.2 V, 9 V
3.6
2.4
–10 dB
1.2
0 dB
0
–1.2
100
200
500
1k
2k
Frequency (Hz)
5k
10 k
20 k
Decode Cut vs. Frequency (V CC = 8.2 V, 9 V, 16 V)
1.2
HA12160
Vin = 0 dB
0
–10 dB
–1.2
Decode Cut (dB)
–2.4
–20 dB
8.2 V, 9 V
–3.6
–4.8
–6.0
16 V
–30 dB
–7.2
–8.4
–9.6
–10.8
100
Rev.4, Jun. 1999, page 58 of 66
–40 dB
200
500
1k
2k
Frequency (Hz)
5k
10 k
20 k
HA12163 Series
TAIin Input Amp. Gain vs. Frequency (PBmode)
28
HA12160
24
Gain (dB)
PBOUT NR-OFF
20
RECOUT NR-ON/OFF
16
12
V CC = 9 V
8
10
100
1k
10 k
Frequency (Hz)
100 k
500 k
RAIin Input Amp. Gain vs. Frequency (RECmode)
28
HA12160
Gain (dB)
24
PBOUT NR-ON/OFF
20
16
RECOUT NR-OFF
12
V CC = 9 V
8
10
100
1k
10 k
Frequency (Hz)
100 k
500 k
Rev.4, Jun. 1999, page 59 of 66
HA12163 Series
Maximum Output Level vs. Supply Voltage (1)
(RAIin RECmode RECOUT)
20
Maximum Output Level Vo max (dB)
HA12160
15
NR-ON
NR-OFF
f = 1 kHz
T.H.D. = 1 %
0 dB = 300 mVrms
10
8
6
8
10
12
14
16
Supply Voltage (V)
Maximum Output Level vs. Supply Voltage (2)
(RAIin PBmode PBOUT)
20
Maximum Output Level Vo max (dB)
HA12160
15
NR-ON
NR-OFF
f = 1 kHz
T.H.D = 1 %
0 dB = 550 mVrms
10
8
6
8
10
12
Supply Voltage (V)
Rev.4, Jun. 1999, page 60 of 66
14
16
HA12163 Series
Signal to Noise Ratio vs. Supply Voltage
90
HA12160
PBmode NR-OFF
80
RECmode NR-ON
70
←
Signal to Noise Ratio S/N (dB)
RECmode NR-OFF
PBmode NR-ON
RAIin PBOUT, RECOUT
VCC = 9 V
f = 1 kHz
CCIR/ARM
60
5
6
8
10
12
14
Supply Voltage (V)
16
18
Total Harmonic Distortion vs. Output Level (1)
(RAIin RECmode RECOUT NR-ON)
Total Harmonic Distortion T.H.D. (%)
HA12160
fin = 100 Hz
fin = 1 kHz
fin = 10 kHz
VCC = 9 V
2
1.0
0.5
0.2
0.1
0.05
0.02
0.01
−15
−10
−5
0
5
10
Output Level Vout (dB)
15
Rev.4, Jun. 1999, page 61 of 66
HA12163 Series
Total Harmonic Distortion vs. Output Level (2)
(RAIin RECmode RECOUT NR-OFF)
2
Total Harmonic Distortion T.H.D. (%)
HA12160
fin = 100 Hz
fin = 1 kHz
fin = 10 kHz
VCC = 9 V
1.0
0.5
0.2
0.1
0.05
0.02
0.01
−15
−10
−5
0
5
Output Level Vout (dB)
10
15
Total Harmonic Distortion vs. Output Level (3)
(RAIin PBmode PBOUT NR-ON)
5
Total Harmonic Distorition T.H.D. (%)
HA12160
2
1.0
fin = 100 Hz
fin = 1 kHz
fin = 10 kHz
VCC = 9 V
0.5
0.2
0.1
0.05
0.02
0.01
−15
Rev.4, Jun. 1999, page 62 of 66
−10
−5
0
5
Output Level Vout (dB)
10
15
HA12163 Series
5
Total Harmonic Distortion vs. Output Level (4)
(RAIin PBmode PBOUT NR-OFF)
Total Harmonic Distorition T.H.D. (%)
HA12160
fin = 100 Hz
fin = 1 kHz
fin = 10 kHz
VCC = 9 V
2
1.0
0.5
0.2
0.1
0.05
0.02
0.01
−15
−10
−10
−5
0
5
10
Output Level Vout (dB)
15
Ripple Rejection Ratio vs. Frequency (RECmode)
Ripple Rejection Ratio R.R.R (dB)
HA12160
V CC = 9 V
−20
−30
NR-ON
−40
NR-OFF
−50
−60
20
50
100
200
500
1k
2k
5k
10 k 20 k
Frequency (Hz)
Rev.4, Jun. 1999, page 63 of 66
HA12163 Series
Ripple Rejection Ratio vs. Frequency (PBmode)
−10
Ripple Rejection Ratio R.R.R (dB)
HA12160
V CC = 9 V
−20
−30
PBOUT NR-ON
−40
PBOUT NR-OFF
EQOUT NR-ON/OFF
−50
−60
20
50
100
200
500
1k
2k
Frequency (Hz)
Rev.4, Jun. 1999, page 64 of 66
5k
10 k 20 k
HA12163 Series
Package Dimensions
Unit: mm
24
48
0.5
37
13
12
0.08
M
0.10 ± 0.07
0.75
*0.17 ± 0.05
0.15 ± 0.04
1
*0.21 ± 0.05
0.19 ± 0.04
1.40
1.70 Max
9.0 ± 0.2
9.0 ± 0.2
7.0
36
25
0.10
1.00
0.75
0˚ – 8˚
0.50 ± 0.10
Hitachi Code
JEDEC
EIAJ
Weight (reference value)
*Dimension including the plating thickness
Base material dimension
FP-48
—
Conforms
0.2 g
12.8 ± 0.3
Unit: mm
10.0
42
29
43
0.65
12.8 ± 0.3
28
56
15
1
0.35
0.10
*Dimension including the plating thickness
Base material dimension
0.1 +0.1
–0.09
0.775
2.20
0.13 M
*0.17 ± 0.05
0.15 ± 0.04
*0.32 ± 0.08
0.30 ± 0.06
2.54 Max
14
0.775
1.40
0˚ – 8 ˚
0.60 ± 0.15
Hitachi Code
JEDEC
EIAJ
Weight (reference value)
FP-56
—
—
0.5 g
Rev.4, Jun. 1999, page 65 of 66
HA12163 Series
Disclaimer
1. Hitachi neither warrants nor grants licenses of any rights of Hitachi’s or any third party’s patent,
copyright, trademark, or other intellectual property rights for information contained in this document.
Hitachi bears no responsibility for problems that may arise with third party’s rights, including
intellectual property rights, in connection with use of the information contained in this document.
2. Products and product specifications may be subject to change without notice. Confirm that you have
received the latest product standards or specifications before final design, purchase or use.
3. Hitachi makes every attempt to ensure that its products are of high quality and reliability. However,
contact Hitachi’s sales office before using the product in an application that demands especially high
quality and reliability or where its failure or malfunction may directly threaten human life or cause risk
of bodily injury, such as aerospace, aeronautics, nuclear power, combustion control, transportation,
traffic, safety equipment or medical equipment for life support.
4. Design your application so that the product is used within the ranges guaranteed by Hitachi particularly
for maximum rating, operating supply voltage range, heat radiation characteristics, installation
conditions and other characteristics. Hitachi bears no responsibility for failure or damage when used
beyond the guaranteed ranges. Even within the guaranteed ranges, consider normally foreseeable
failure rates or failure modes in semiconductor devices and employ systemic measures such as failsafes, so that the equipment incorporating Hitachi product does not cause bodily injury, fire or other
consequential damage due to operation of the Hitachi product.
5. This product is not designed to be radiation resistant.
6. No one is permitted to reproduce or duplicate, in any form, the whole or part of this document without
written approval from Hitachi.
7. Contact Hitachi’s sales office for any questions regarding this document or Hitachi semiconductor
products.
Sales Offices
Hitachi, Ltd.
Semiconductor & Integrated Circuits.
Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan
Tel: Tokyo (03) 3270-2111 Fax: (03) 3270-5109
URL
NorthAmerica
: http://semiconductor.hitachi.com/
Europe
: http://www.hitachi-eu.com/hel/ecg
Asia
: http://sicapac.hitachi-asia.com
Japan
: http://www.hitachi.co.jp/Sicd/indx.htm
For further information write to:
Hitachi Semiconductor
(America) Inc.
179 East Tasman Drive,
San Jose,CA 95134
Tel: <1> (408) 433-1990
Fax: <1>(408) 433-0223
Hitachi Europe GmbH
Electronic Components Group
Dornacher Straße 3
D-85622 Feldkirchen, Munich
Germany
Tel: <49> (89) 9 9180-0
Fax: <49> (89) 9 29 30 00
Hitachi Europe Ltd.
Electronic Components Group.
Whitebrook Park
Lower Cookham Road
Maidenhead
Berkshire SL6 8YA, United Kingdom
Tel: <44> (1628) 585000
Fax: <44> (1628) 585160
Hitachi Asia Ltd.
Hitachi Tower
16 Collyer Quay #20-00,
Singapore 049318
Tel : <65>-538-6533/538-8577
Fax : <65>-538-6933/538-3877
URL : http://www.hitachi.com.sg
Hitachi Asia Ltd.
(Taipei Branch Office)
4/F, No. 167, Tun Hwa North Road,
Hung-Kuo Building,
Taipei (105), Taiwan
Tel : <886>-(2)-2718-3666
Fax : <886>-(2)-2718-8180
Telex : 23222 HAS-TP
URL : http://www.hitachi.com.tw
Hitachi Asia (Hong Kong) Ltd.
Group III (Electronic Components)
7/F., North Tower,
World Finance Centre,
Harbour City, Canton Road
Tsim Sha Tsui, Kowloon,
Hong Kong
Tel : <852>-(2)-735-9218
Fax : <852>-(2)-730-0281
URL : http://www.hitachi.com.hk
Copyright  Hitachi, Ltd., 2000. All rights reserved. Printed in Japan.
Colophon 2.0
Rev.4, Jun. 1999, page 66 of 66