FAIRCHILD CD4016BC

Revised March 2002
CD4016BC
Quad Bilateral Switch
General Description
■ Extremely high control input impedance: 1012Ω (typ)
The CD4016BC is a quad bilateral switch intended for the
transmission or multiplexing of analog or digital signals. It is
pin-for-pin compatible with CD4066BC.
■ Low crosstalk between switches:
−50 dB (typ.)
@ fIS = 0.9 MHz, RL = 1 kΩ
■ Frequency response, switch “ON”: 40 MHz (typ)
Features
■ Wide supply voltage range: 3V to 15V
■ Wide range of digital and analog switching: ±7.5 VPEAK
Applications
• Analog signal switching/multiplexing
■ “ON” Resistance for 15V operation: 400Ω (typ)
Signal gating
■ Matched “ON” Resistance over 15V signal input:
Squelch control
∆RON = 10Ω (typ)
Chopper
■ High degree of linearity:
Modulator/Demodulator
0.4% distortion (typ)
Commutating switch
@ fIS = 1 kHz, VIS = 5 Vp-p,
• Digital signal switching/multiplexing
VDD−VSS = 10V, RL = 10 kΩ
• CMOS logic implementation
• Analog-to-digital/digital-to-analog conversion
■ Extremely low “OFF” switch leakage:
• Digital control of frequency, impedance, phase, and
analog-signal gain
0.1 nA (typ.)
@ VDD − VSS = 10V
TA = 25°C
Ordering Code:
Order Number
Package Number
Package Description
CD4016BCM
M14A
14-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-012, 0.150" Narrow
CD4016BCN
N14A
14-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300" Wide
Devices also available in Tape and Reel. Specify by appending the letter suffix “X” to the ordering code.
Connection Diagram
© 2002 Fairchild Semiconductor Corporation
Schematic Diagram
DS005661
www.fairchildsemi.com
CD4016BC Quad Bilateral Switch
November 1983
CD4016BC
Absolute Maximum Ratings(Note 1)
Recommended Operating
Conditions (Note 2)
(Note 2)
−0.5V to +18V
VDD Supply Voltage
VIN Input Voltage
TS Storage Temperature Range
−0.5V to VDD + 0.5V
−65°C to + 150°C
VDD Supply Voltage
3V to 15V
VIN Input Voltage
0V to VDD
−55°C to +125°C
TA Operating Temperature Range
Power Dissipation (PD)
Dual-In-Line
700 mW
Small Outline
500 mW
Note 1: “Absolute Maximum Ratings” are those values beyond which the
safety of the device cannot be guaranteed. They are not meant to imply
that the devices should be operated at these limits. The tables of “Recommended Operating Conditions” and “Electrical Characteristics” provide conditions for actual device operation.
Lead Temperature
260°C
(Soldering, 10 seconds)
Note 2: VSS = 0V unless otherwise specified.
DC Electrical Characteristics (Note 2)
Symbol
IDD
Parameter
−55°C
Conditions
Min
Max
+125°C
25°C
Min
Typ
Max
Min
Max
Units
Quiescent Device
VDD = 5V, VIN = VDD or VSS
0.25
0.01
0.25
7.5
µA
Current
VDD = 10V, VIN = VDD or VSS
0.5
0.01
0.5
15
µA
VDD = 15V, VIN = V DD or VSS
1.0
0.01
1.0
30
µA
VDD = 10V
600
250
660
960
Ω
VDD = 15V
360
200
400
600
Ω
Signal Inputs and Outputs
RON
“ON” Resistance
RL = 10kΩ to (VDD − V SS)/2
VC = VDD, VIS = VSS or VDD
RL = 10kΩ to (VDD − V SS)/2
VC = VDD
∆RON
IIS
∆“ON” Resistance
VDD = 10V, VIS = 4.75 to 5.25V
1870
850
2000
2600
Ω
VDD = 15V, VIS = 7.25 to 7.75V
775
400
850
1230
Ω
RL = 10kΩ to (VDD − V SS)/2
Between any 2 of
VC = VDD, VIS = VSS to VDD
4 Switches
VDD = 10V
15
(In Same Package)
VDD = 15V
10
Input or Output
VC = 0, VDD = 15V
Leakage
VIS = 0V or 15V,
Switch “OFF”
VOS = 15V or 0V
±50
±0.1
Ω
Ω
±50
±500
nA
Control Inputs
VILC
LOW Level Input
VIS = VSS and VDD
Voltage
VOS = VDD and VSS
IIS = ±10 µA
VIHC
VDD = 5V
0.9
0.7
0.5
V
VDD = 10V
0.9
0.7
0.5
V
VDD = 15V
0.9
0.7
0.5
V
HIGH Level Input
VDD = 5V
3.5
3.5
3.5
V
Voltage
VDD = 10V
7.0
7.0
7.0
V
VDD = 15V
11.0
11.0
11.0
V
(Note 3) and Table 1
IIN
Input Current
VCC − VSS = 15V
±0.1
±10−5
±0.1
±1.0
µA
VDD ≥ VIS ≥ VSS
VDD ≥ VC ≥ VSS
Note 3: If the switch input is held at VDD, VIHC is the control input level that will cause the switch output to meet the standard “B” series VOH and IOH output
levels. If the analog switch input is connected to VSS, VIHC is the control input level — which allows the switch to sink standard “B” series |IOH|, HIGH level
current, and still maintain a VOL ≤ “B” series. These currents are shown in Table 1.
www.fairchildsemi.com
2
(Note 4)
TA = 25°C, tr = tf = 20 ns and VSS = 0V unless otherwise specified
Symbol
tPHL, tPLH
tPZH, tPZL
tPHZ, tPLZ
Parameter
Conditions
Typ
Max
Units
VDD = 5V
58
100
ns
VDD= 10V
27
50
ns
VDD = 15V
20
40
ns
ns
Propagation Delay Time
VC = VDD, CL = 50 pF, (Figure 1)
Signal Input to Signal Output
RL = 200k
Min
Propagation Delay Time
RL = 1.0 kΩ, CL = 50 pF, (Figure 2, Figure 3)
Control Input to Signal
VDD = 5V
20
50
Output HIGH Impedance to
VDD = 10V
18
40
ns
Logical Level
VDD = 15V
17
35
ns
Propagation Delay Time
RL = 1.0 kΩ, CL = 50 pF, (Figure 2, Figure 3)
Control Input to Signal
VDD = 5V
15
40
ns
Output Logical Level to
VDD = 10V
11
25
ns
HIGH Impedance
VDD = 15V
10
22
ns
Sine Wave Distortion
VC = VDD = 5V, VSS = −5
0.4
%
40
MHz
1.25
MHz
0.9
MHz
150
mVP-P
VDD = 5V
6.5
MHz
VDD = 10V
8.0
MHz
VDD = 15V
9.0
MHz
RL = 10 kΩ, VIS = 5 VP-P, f = 1 kHz,
(Figure 4)
Frequency Response — Switch
VC = VDD = 5V, VSS = −5V,
“ON” (Frequency at −3 dB)
RL = 1 kΩ, VIS = 5 VP-P,
20 Log10 V OS/VOS (1 kHz) −dB,
(Figure 4)
Feedthrough — Switch “OFF”
VDD = 5V, VC = VSS = −5V,
(Frequency at −50 dB)
RL = 1 kΩ, VIS = 5 VP-P,
20 Log10 (VOS/VIS) = −50 dB,
(Figure 4)
Crosstalk Between Any Two
VDD = VC(A) = 5V; VSS = VC(B) = −5V,
Switches (Frequency at −50 dB)
RL = 1 kΩVIS(A) = 5 VP-P,
20 Log10 (VOS(B)/VOS(A) ) = −50 dB,
(Figure 5)
Crosstalk; Control Input to
VDD = 10V, RL = 10 kΩ
Signal Output
RIN = 1 kΩ, VCC = 10V Square Wave,
Maximum Control Input
RL = 1 kΩ, CL = 50 pF, (Figure 7)
CL = 50 pF (Figure 6)
VOS(f) = ½ VOS(1 kHz)
CIS
Signal Input Capacitance
COS
Signal Output Capacitance
VDD = 10V
CIOS
Feedthrough Capacitance
VC = 0V
CIN
Control Input Capacitance
4
pF
4
pF
0.2
5
pF
7.5
pF
Note 4: AC Parameters are guaranteed by DC correlated testing.
Note 5: These devices should not be connected to circuits with the power “ON”.
Note 6: In all cases, there is approximately 5 pF of probe and jig capacitance on the output; however, this capacitance is included in CL wherever it is
specified.
Note 7: VIS is the voltage at the in/out pin and VOS is the voltage at the out/in pin. VC is the voltage at the control input.
3
www.fairchildsemi.com
CD4016BC
AC Electrical Characteristics
CD4016BC
AC Test Circuits and Switching Time Waveforms
FIGURE 1. tPLH, tPLH Propagation Delay Time Control to Signal Output
FIGURE 2. tPZH, tPHZ Propagation Delay Time Control to Signal Output
FIGURE 3. tPZH, tPHZ Propagation Delay Time Control to Signal Output
VC = VDD for distortion and frequency response tests
VC = VSS for feedthrough test
FIGURE 4. Sine Wave Distortion, Frequency Response and Feedthrough
www.fairchildsemi.com
4
CD4016BC
AC Test Circuits and Switching Time Waveforms
(Continued)
FIGURE 5. Crosstalk Between Any Two Switches
FIGURE 6. Crosstalk — Control to Input Signal Output
FIGURE 7. Maximum Control Input Frequency
5
www.fairchildsemi.com
CD4016BC
TABLE 1. CD4016B Switch Test Conditions for VIHC
Temperature
Switch Input
VDD
Range
COMMERCIAL
VIS
Switch Output
IIS (mA)
VOS(V)
−40°C
25°C
+85°C
5
0
0.2
0.16
0.12
5
5
−0.2
−0.16
−0.12
10
0
0.5
0.4
0.3
10
10
−0.5
−0.4
−0.3
15
0
1.4
1.2
1.0
15
15
−1.4
−1.2
−1.0
Min
Max
0.4
4.6
0.5
9.5
1.5
13.5
Typical Performance Characteristics
’ON’ Resistance vs.
Signal Voltage TA = 25°C
’ON’ Resistance Temperature Variation
for VDD − VSS = 10V
’ON’ Resistance Temperature Variation
for VDD − VSS = 15V
www.fairchildsemi.com
6
CD4016BC
Typical Applications
4 Input Multiplexer
Sample/Hold Amplifier
Special Considerations
non-linear. It is recommended that at 5V, voltages on the
in/out pins be maintained within about 1V of either VDD or
VSS; and that at 3V the voltages on the in/out pins should
be at VDD or VSS for reliable operation.
The CD4016B is composed of 4, two-transistor analog
switches. These switches do not have any linearization or
compensation circuitry for “RON” as do the CD4066B's.
Because of this, the special operating considerations for
the CD4066B do not apply to the CD4016B, but at low supply voltages, ≤5V, the CD4016B's On Resistance becomes
7
www.fairchildsemi.com
CD4016BC
Physical Dimensions inches (millimeters) unless otherwise noted
14-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-012, 0.150" Narrow
Package Number M14A
www.fairchildsemi.com
8
CD4016BC Quad Bilateral Switch
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
14-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300" Wide
Package Number N14A
Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and
Fairchild reserves the right at any time without notice to change said circuitry and specifications.
LIFE SUPPORT POLICY
FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD
SEMICONDUCTOR CORPORATION. As used herein:
2. A critical component in any component of a life support
device or system whose failure to perform can be reasonably expected to cause the failure of the life support
device or system, or to affect its safety or effectiveness.
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the
body, or (b) support or sustain life, and (c) whose failure
to perform when properly used in accordance with
instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the
user.
www.fairchildsemi.com
9
www.fairchildsemi.com